Documente Academic
Documente Profesional
Documente Cultură
Setup Guide
http://www.elastix.org
PaloSanto Solutions
Snom 710 Server Setup Guide
2
PaloSanto Solutions
Snom 710 Server Setup Guide
1. Go to the web address of the Elastix Server Login page. The web address is
determined by the customer, for this guide we have used the IP address
192.168.1.75
2. On the Login page, type the username and password for an administrative user into
the Username and Password fields, see Figure 4-1. The username and password are
determined by the customer.
3
PaloSanto Solutions
Snom 710 Server Setup Guide
5. Click on the Submit button to add an extension, see Figure 4-3. This will take you
to the Add SIP Extension page.
6. On the Add SIP Extension page (Figure 4-4), fill in the following information:
7. Click on the „Submit‟ button at the end of the page. The extension will be created
and you will see the page on Figure 4-5 displaying the “Apply Configuration
Changes Here” pink ribbon on top of the screen.
4
PaloSanto Solutions
Snom 710 Server Setup Guide
9. With this you have just finished creating a SIP extension that will be used by the
Snom 710 to register with the Elastix Server. Repeat Steps 5 through 8 to similarly
create another extension (different values on Step 6) to be used by the IP (SIP)
Phone to register as well (extension 302 in this example). Once finished you will
see something similar to Figure 4-6
10. To register the Snom Phone, you will need to enter the information from the
extension created on the Elastix Server into the Snom Phone by logging into the
Snom 710 WebUI.
To register the Snom Phone there are two methods: Manual Configuration and
AutoProvisioning using Elastix’s Endpoint Configurator.
5
PaloSanto Solutions
Snom 710 Server Setup Guide
MANUAL CONFIGURATION
1. Log in to the Snom 710 WebUI by pointing your browser to the Snom Phone‟s IP
address.
For the initial configuration, refer to the Snom 710 User Manual found at:
http://wiki.snom.com/Snom710/Documentation
IP Addressing DHCP
Web Access User Name Not set
Web Access Password Not set
11. When the WebUI is loaded, use the information from the Add SIP Extension page
(Figure 4-4) to enter the following necessary information on “Setup => Identity 1
=> Login” section of the Snom Phone WebUI (Figure 4-7):
Identity active: ON
Displayname: (SnomPhone in this example)
Account: (301 in this example)
Password: (“h7Dka3Rf9si0t” in this example)
Registrar: Elastix Server‟s IP Address (192.168.1.75 in this example)
Outbound Proxy: Elastix Server‟s IP Address (192.168.1.75 in this example)
Authentication Username: (301 in this example)
Mailbox: *97
12. Once you have entered the required information, click on „Save‟ button. Now, go to
“Setup => Identity 1 => RTP”. The “RTP Encryption” option should be set to “off”.
Apply and save changes. (Figure 4-8).
6
PaloSanto Solutions
Snom 710 Server Setup Guide
13. To check the correct registration of the account, go to “Status => System
Information” section (Figure 4-9). If it‟s not registered, make sure you‟ve entered
the correct information.
14. Configure the other IP (SIP) Phone with the correct parameters.
15. To test the Snom 710, pick up the previously configured IP (SIP) Phone and call
the Snom 710‟s extension number (301 in this example). When the call is
established, speak into the phone and verify that the other IP (SIP) Phone can hear
your voice. Check this by calling from both ends.
7
PaloSanto Solutions
Snom 710 Server Setup Guide
Note: The support for Endpoint Configurator is available in Elastix 2.4 by installing the
new Endopoint configurator module. This new module is already included in Elastix
2.5.
1. For Elastix 2.4, log in to the console and install the module by entering the
command:
yum -y install elastix-endpointconfig2
2. After installation, in the Elastix Web Interface go to “PBX => Batch Configurations
=> New Endpoint Configurator”. See figure 4-10
3. Type the network address where the phone is located and click on the magnifying
glass. This will generate a list with all the phones available in that network. See
figure 4-11.
4. In the row where the phone you want to autoprovision is located (find it according
to either its MAC or IP Address):
8
PaloSanto Solutions
Snom 710 Server Setup Guide
5. After clicking in the configuration link, you will see a window with many tabs
according to what you want to configure. In this case we will configure a SIP
account. Go to the tab “Accounts” and drag the accounts you want to assign from
left to right. Then click on Apply button. See figure 4-12.
6. After configuring you will see that the status field of the phone has changed. See
figure 4-13
7. Now with the phones selected, click on the button “Apply Configuration” located
next to the magnifying glass button. A message will be shown saying the operation
was successful. See figure 4-14.
9
PaloSanto Solutions
Snom 710 Server Setup Guide
8. Your phone will reboot, and when it boots up it should be registered with Elastix
with the accounts you set. This step completes the procedure.
10