Documente Academic
Documente Profesional
Documente Cultură
com
E-mail:http://www.LGEservice.com/techsup.html
COLOR MONITOR
SERVICE MANUAL
CHASSIS NO. : CL-61
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
SPECIFICATIONS
Opraating Mode : Transmissive mode, Normally white POWER ON (NORMAL) ON/ON ACTIVE less than 25 W GREEN
Electrical Interface : LVDS interface
STAND-BY OFF/ON OFF less than 1 W AMBER
Top : typ.
4. MAX. RESOLUTION
-2-
Signal Connector Pin Assignment
?
DVI-I Connector (Digital/Analog)
Pin Signal (DVI-D) Pin Signal (DVI-D)
T. M. D. S. Data2- 16 Hot Plug Detect
T. M. D. S. Data2+ 17 T. M. D. S. Data0-
T. M. D. S. Data2/4 Shield T. M. D. S. Data0+
123456789
18
T. M. D. S. Data4- 19 T. M. D. S. Data0/5 Shield
T. M. D. S. Data4+ 20 T. M. D. S. Data5-
T. M. D. S. Data1- 24 T. M. D. S. Clock-
10 T. M. D. S. Data1+
11 T. M. D. S. Data1/3 Shield
12 T. M. D. S. Data3-
13 T. M. D. S. Data3+
14 +5V Power
-3-
PRECAUTION
permission from manufacturer or you will void the burn or take fire.
TAKE CARE DURING HANDLING THE LCD MODULE Leakage Current Hot Check Circuit
WITH BACKLIGHT UNIT.
AC Volt-meter
?
Must mount the module using mounting holes arranged
in four corners.
?
Do not press on the panel, edge of the frame strongly
orelectric shock as this will result in damage to the Good Earth Ground
such as WATER PIPE,
screen.
CONDUIT etc.
To Instrument's
?
Do not scratch or press on the panel with any sharp exposed
METALLIC PARTS
objects, such as pencil or pen as this may result in
?
Do not leave the module in high temperature and in
areas of high humidity for a long time.
?
The module not be exposed to the direct sunlight.
?
Avoid contact with water as it may a short circuit within
the module.
?
If the surface of panel become dirty, please wipe it off
with a softmaterial.
(Cleaning with a dirty or rough cloth
may damage the panel.)
CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.
-4-
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this 9. Use with this receiver only the test fixtures specified in
service manual and its supplements and addenda, read this service manual.
and follow the SAFETY PRECAUTIONS on page 3 of this CAUTION: Do not connect the test fixture ground strap
publication. to any heat sink in this receiver.
NOTE: If unforeseen circumstances create conflict
between the following servicing precautions and any of the Electrostatically (ES) Devices
Sensitive
safety precautions on page 3 of this publication, always Some semiconductor (solid-state) devices can be
follow the safety precautions. Remember: Safety First. damaged easily by static electricity. Such components
commonly are called Electrostatically Sensitive (ES)
General Servicing Precautions Devices. Examples of typical ES devices are integrated
1. Always unplug the receiver AC power cord from the AC circuits and some field-effect transistors and
power source before; semiconductor "chip" components. The following
a. Removing or reinstalling any component, circuit techniques should be used to help reduce the incidence of
board module orany other receiver assembly. component damage caused by static by static electricity.
b. Disconnecting or reconnecting any receiver electrical 1. Immediately before handling any semiconductor
d. Discharging the picture tube anode. 2. After removing an electrical assembly equipped with
2. Test high voltage only by measuring it with an ES devices, place the assembly on a conductive
appropriate high voltage meter or other voltage surface such as aluminum foil, to prevent electrostatic
measuring device (DVM, FETVOM, etc) equipped with charge buildup or exposure of the assembly.
a suitable high voltage probe. 3. Use only a grounded-tip soldering iron to solder or
4. Do not spray chemicals on or near this receiver or any protective package until immediately before you are
of its assemblies. ready to install it. (Most replacement ES devices are
5. Unless specified otherwise in this service manual, packaged with leads electrically shorted together by
clean electrical contacts
only by applying the following conductive foam, aluminum foil or comparable
mixture to the contacts with a pipe cleaner, cotton- conductive material).
tipped stick or comparable non-abrasive applicator; 7. Immediately before removing the protective material
10% (by volume) Acetone and 90% (by volume) from the leads of a replacement ES device, touch the
isopropyl alcohol (90%-99% strength) protective material to the chassis or circuit assembly
CAUTION: This is a flammable mixture. into which the device will be installed.
Unless specified otherwise in this service manual, CAUTION: Be sure no power is applied to the chassis
-5-
General Soldering Guidelines Replacement
1. Use grounded-tip, low-wattage soldering iron and
a 1. Carefully insert the replacement IC in the circuit board.
appropriate tip size and shape that will maintain tip 2. Carefully bend each IC lead against the circuit foil pad
within the range 500 F to 600 F. and solder it.
temperature or
2. Use an appropriate gauge of RMA resin-core solder 3. Clean the soldered areas with a small wire-bristle
brush. (It is not necessary to reapply acrylic coating to
composed of 60 parts tin/40 parts lead.
3. Keep the soldering iron tip clean and well tinned. the areas).
4. Thoroughly clean the surfaces to be soldered. Use a
mall wire-bristle (0.5 inch, or 1.25cm) brush with a "Small-Signal" Discrete Transistor
metal handle. Removal/Replacement
Do not 1. Remove the defective transistor by clipping its leads
freon-propelled spray-on cleaners.
use as
5. Use the following unsoldering technique close as possible to the component body.
a. Allow the soldering iron tip to reach normal 2. Bend into a "U" shape the end of each of three leads
-6-
Circuit Board Foil Repair At Other Connections
Excessive heat the copper foil of any printed
applied to Use the following technique to repair the defective copper
circuit board will weaken the adhesive that bonds the foil pattern at connections other than IC Pins. This technique
to the circuit board causing the foil to separate from or involves the installation of a jumper wire on the
"lift-off" the board. The following guidelines and component side of the circuit board.
procedures should be followed whenever this condition is 1. Remove the defective copper pattern with a sharp
encountered. knife.
Remove at least 1/4 inch of copper, to ensure that a
At IC Connections hazardous condition will not exist if the jumper wire
To repair a defective copper pattern at IC connections use opens.
the following procedure to install a jumper wire on the 2. Trace along the copper pattern from both sides of the
copper pattern side of the circuit board. (Use this pattern break and locate the nearest component that is
technique only on IC connections). directly connected to the affected copper pattern.
3. Connect insulated 20-gauge jumper wire from the lead
1. Carefully remove the damaged copper pattern with a of the nearest component on one side of the pattern
sharp knife. (Remove only as much copper as break to the lead of the nearest component on the
absolutely necessary). other side.
2. carefully scratch away the solder resist and acrylic Carefully crimp and solder the connections.
coating (if used) from the end of the remaining copper CAUTION: Be sure the insulated jumper wire is
pattern. dressed so the it does not touch components or sharp
3. Bend a small "U" in one end of small gauge jumper
a edges.
wire and carefully crimp it around the IC pin. Solder the
IC connection.
4. Route the jumper wire along the path of the out-away
copper pattern and let it overlap the previously scraped
end of the good copper pattern. Solder the overlapped
area and clip off any excess jumper wire.
-7-
TIMING CHART
VIDEO
A
D B
SYNC
H (Pixels)
--
H (Pixels)
--
H (Pixels)
--
H (Pixels)
--
H (Pixels)
--
H (Pixels)
--
-8-
DISASSEMBLY
#1 #4
1. Put a soft cushion on the floor and lay the stand on its 4. Cover the panel with your hand so that it is not scratched.
side so that the base is accessible. Then, pull up the cabinet corner side.
#2 #5
2. Hold the set while folding the latch and take out the stand 5-1. Disassemble the cabinet.
base.
5-2. Hold the control PCB as shown in the figure and gently
pull it out.
#3 #6
3-1. Push the cover upward and remove it. 6. Push up the back cover as shown in the figure and pull
3-2. Unscrew the four screws.
out the chassis assembly so that the latch is untied.
-9-
#7 #9
7. Push the shield cap upward and disassemble it. 9. Pull out the link cable while pushing up the main frame.
#8
-10-
WIRING DIAGRAM
J707
J1
Control Board
-11-
BLOCK DIAGRAM
-12-
DESCRIPTION OF BLOCK DIAGRAM
The Scaler gets the video signal converted analog to digital, interpolates input to 1280 X 768 resolution signal
and outputs 8-bit R, G, B signal to transmitter.
2. Power Part.
This part consists of the two 3.3V regulators, and two 2.5V drop diodes to convert power which is provided 12V,
5V in Power board.
3.3V is Provided for LCD panel and 5V is Provided for Micom
Also, 5V is converted 3.3V by regulator and 3.3V is converted 2.5V by drop diode.
Converted power is provided for IC in the main board.
3. MICOM Part.
This part consists of EEPROM IC which stores control data, Reset IC and the Micom.
The Micom distinguishes polarity and
frequency of the H/V sync are supplied from signal cable.
The controlled data of each modes is stored in EEPROM.
-13-
LIPS Board Block Diagram
12V
50 ~
60Hz
HVDC 100KHz 5V
EMI INPUT RECTIFIER ENERGY OUTPUT RECTIFIER
COMPONENTS AND FILTER TRANSFER AND FILTER
LINE GND
100 ~
240V
PWM SIGNAL
PHOTO-
CONTROL COLLECTI
COUPLER
CIRCUIT ON
ISOLATION
PRIMARY SECONDARY
Operation description_LIPS
1. EMI components.
This part contains of EMI components to comply with global marketing EMI standards like FCC,VCCI CISPR,
the circuit included a line-filter, across line capacitor and of course the primary protection fuse.
3. Energy Transfer.
This part function is for transfer the primary energy to secondary through a power transformer.
5. Photo-Coupler isolation.
This part function is to feed back the dc output changing status through a photo transistor to primary controller to
achieve the stabilized dc output voltage.
6. Signal collection.
This part function is to collect the any change from the dc output and feed back to the primary through photo
transistor
-14-
ADJUSTMENT
1) Run WinEDID.exe
1. PortSetup
a) Copy "UserPort.sys" file to
"c:\WINNT\system32\drivers" folder
b) Run Userport.exe
d) Add 300-3FF
-15-
SERVICE OSD
4)The service OSD menu contains additional menus that the User OSD menu as described below.
PUSH
9 6
IBM 5 1
11
Video Signal Compatible PC 1510 6
5 1
Generator C
PARALLEL PORT 13 1
used 25 14
Not
RS232C OFF ON
5V
F
C
PARALLEL
ContrlLie VGS POWER
220
Power inlet (required)
Power Select Switch
(110V/220V)
ON
E
5V
4.7K
5V
4.7K4.7K
74LS06
OFF
A ST Power LED
E ST Switch
B B
-16-
TROUBLESHOOTING GUIDE
1. NO POWER
NO POWER
(POWER INDICATOR OFF)
YES
YES
NO PROBLEM
CHECK KEY CONTROL
CONNECTOR ROUTINE
YES
IS U201 NO
PIN114 (3.3V) CHECK 3.3V LINE
VOLTAGE ?
YES
NO
2 CHECK U201 PIN 122 CHECK X-TAL
PULSE
YES
CHECK U201
Waveforms
-17-
2. NO RASTER (OSD IS NOT DISPLAYED) --
LIPS
NO RASTER
(OSD IS NOT DISPLAYED)
J707
NO
PIN5, PIN6 CHECK LIPS
5V?
YES
YES
1. CONFIRM BRIGHTNESS
J707 PIN1 NO OSD CONTRL STATE.
5V? 2. CHECK MICOM DIM-ADJ
PORT
YES
CHECK
PULSE AS
CONTACTING SCOPE
PROBE TO CAUTION LABEL. NO
PROBE TO REPLACE LIPS
(CONTACT
CAUTION LABEL.
CAN YOU SEE PULSE
AT YOUR
SCOPE?
YES
Waveforms
3 J707-#2 3 J707-#2
-18-
3. NO RASTER (OSD IS NOT DISPLAYED) --
MST9111B
NO RASTER
(OSD IS NOT DISPLAYED)
U201 NO
POWER PIN8, 114 CHECK U801
3.3V?
YES
YES
U501
PIN43 IS 48KHz H-SYNC?
NO CHECK CONNECTION LINE
5 PIN44 IS 60Hz V-SYNC?
FROM D-SUB TO U501
IS PULSE APPEARED
AT SIGNAL PINS?
AT MODE 12?
YES
TROUBLE IN CABLE
OR LCD MODULE
Waveforms
-19-
4. TROUBLE IN DPM
TROUBLE IN DPM
CHECK NO CHECK PC
6 PC IS NOT GOING
R773, R775 (SYNC) ?
INTO DPM OFF MODE
YES
CHECK NO
U501 PIN 19 CHECK H/V SYNC LINE
YES
TROUBLE IN PC
Waveforms
-20-
110
040
050
140
030
100
070
EXPLODVIW
130 070
060
090
080
120
020
010
-21-
EXPLODED VIEW PARTS LIST
6304FLP172A LCD(LIQUID CRYSTAL DISPLAY), LM150X08-A5 LG PHILPS TFT COLOR SOURCE D-IC 624CH,PSWG,LVDS,16MS,OKI/OKI
6304FLP173A LCD(LIQUID CRYSTAL DISPLAY), LM150X08-A5N1 LG PHILPS TFT COLOR LPL NJ,SOURCE D-IC624CH,PSWG,LVDS,16MS,OKI/OKI
020
6304FLP116A LCD(LIQUID CRYSTAL DISPLAY), LM150X08-A4N7 LG PHILPS TFT COLOR A4K3 LPL NJ,XGA,250NITS,
6304FLP146A LCD(LIQUID CRYSTAL DISPLAY), LM150X08-A4K8 LG PHILPS TFT COLOR PSWG,LVDS,16MS,SS S D-IC
6304FLP156A LCD(LIQUID CRYSTAL DISPLAY ), LM150X08-A4NA LG PHILPS TFT COLOR PSWG,LVDS,16MS,SS S D-IC LPL NJ,250NITS
6871TPT271X PWB(PCB) ASSEMBLY,POWER, M-CHASSIS 15INCH POWER TOTAL LIEN CHANG C306 68PF 450V
080
6871TPT271N PWB(PCB) ASSEMBLY,POWER, M-CHASSIS 15INCH POWER TOTAL LIEN CHANG C306 68PF
120 6631T11012R CONNECTOR ASSEMBLY, 20P H-H 140MM UL20276 PANEL LINK CABLE LM567D
-22-
REPLACEMENT PARTS LIST
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
MAIN BOARD
CAPACITORS C804 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C805 0CK105CD56A 1UF 1608 10V 10% R/TP X7R
C204 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C806 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C205 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C807 0CE107EF610 "100UF KMG,RD 16V 20% FL BULK"
C206 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C808 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C207 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C809 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C208 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C810 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C209 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C812 0CE107EF610 "100UF KMG,RD 16V 20% FL BULK"
C210 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C814 0CE107EF610 "100UF KMG,RD 16V 20% FL BULK"
C211 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C815 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C214 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C816 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C215 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C817 0CK105CD56A 1UF 1608 10V 10% R/TP X7R
C216 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C818 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C220 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R D701 0DS226009AA KDS226 TP KEC SOT-23 80V 30
C221 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R D702 0DS226009AA KDS226 TP KEC SOT-23 80V 30
C222 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R D706 0DS226009AA KDS226 TP KEC SOT-23 80V 30
C223 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R D804 0DD184009AA KDS184 TP KEC -
85V - - -
30
C225 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R D805 0DD184009AA KDS184 TP KEC -
85V - - -
30
C226 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R ZD701 0DZ560009GB BZT52C5V6S DIODES R/TP SOD32
C227 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R ZD702 0DZ560009GB BZT52C5V6S DIODES R/TP SOD32
C230 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R ZD703 0DZ560009GB BZT52C5V6S DIODES R/TP SOD32
C231 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R ZD704 0DZ560009GB BZT52C5V6S DIODES R/TP SOD32
C232 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R ZD705 0DZ560009GB BZT52C5V6S DIODES R/TP SOD32
C233 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R ZD711 0DZ560009GB BZT52C5V6S DIODES R/TP SOD32
C251 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C501 0CC101CK41A 100PF 1608 50V 5% R/TP NP0 ICs
E
C506 0CC030CK01A 3PF 1608 50V 0.25 PF R/TP NP U502 0ISG240860B M24C08W6 SGS-THOMSON 8SOP R/
C507 0CC180CK41A 18PF 1608 50V 5% R/TP NP0 U801 0IPMGKE011A KIA78D33F KEC DPAK R/TP 3.3V
C508 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R U803 0IPMGK2001B AIC1117A-33CYTR(BS33) AIC SO
C701 0CK105CD56A 1UF 1608 10V 10% R/TP X7R Q502 0IKE704200H KIA7042AP TO-92 TP 4.2 VOLT
C718 0CC101CK41A 100PF 1608 50V 5% R/TP NP0 Q703 0TR390609FA KST3906-MTF TP SAMSUNG SOT2
C719 0CC680CK41A 68PF 1608 50V 5% R/TP NP0 Q704 0TR390609FA KST3906-MTF TP SAMSUNG SOT2
C720 0CC101CK41A 100PF 1608 50V 5% R/TP NP0 Q706 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
C721 0CC680CK41A 68PF 1608 50V 5% R/TP NP0 Q707 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
C727 0CK105CD56A 1UF 1608 10V 10% R/TP X7R U802 0TFVI80023A VISHAY SI3865DV R/TP TSOP-6
C732 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C733 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R RESISTORs
C734 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C735 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R R201 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
C760 0CE107EF610 "100UF KMG,RD 16V 20% FL BULK" R202 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
C801 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y R203 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
C803 0CE107EF610 "100UF KMG,RD 16V 20% FL BULK" R207 0RJ3900D677 390 OHM 1/10 W 5% 1608 R/TP
-23-
DATE: 2004. 11. 4. DATE: 2004. 11. 4.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
R208 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP R744 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R209 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP R745 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R210 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP R747 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R213 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP R748 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R214 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP R749 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R220 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R770 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R506 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R771 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R508 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R772 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R512 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP R773 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R513 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP R774 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R514 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R775 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R515 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R779 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TP
R516 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R780 0RJ2001D677 2K OHM 1/10 W 5% 1608 R/TP
R518 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R781 0RJ2001D677 2K OHM 1/10 W 5% 1608 R/TP
R519 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP R782 0RJ0102D677 10 OHM 1/10 W 5% 1608 R/TP
R520 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R783 0RJ0102D677 10 OHM 1/10 W 5% 1608 R/TP
R521 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R802 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R522 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R807 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R523 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R808 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R524 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP R814 0RJ2202D677 22K OHM 1/10 W 5% 1608 R/TP
R525 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP R815 0RJ5600D677 560 OHM 1/10 W 5% 1608 R/TP
R526 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP R825 0RX0470J609 0.47 OHM 1 W 5% TA52
R531 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP X501 6212AA2004A HC-49U TXC 12.0MHZ +/- 30 PP
R561 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R5 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R563 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP R7 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TP
R564 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP R8 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TP
-24-
SCHEMATIC DIAGRAM
1. SCALER
1U20-#38_RGB
1
2U01-#2
-25-
2. MICOM
3U501-#7~2
3
4U501-#,2
4
5Q0-#3
5
6U502-#,6
6
-26-
3. POWER
-27-
4. CONNECTOR & JACKS
7J0-5V:#,6
8
8J703-#5
8J703-#5
-28-
Blank Page1
Blank Page2
Nov. 2004
P/NO 3828TSL088V
: Printed in Korea