Documente Academic
Documente Profesional
Documente Cultură
1 Top of Form
Which Cisco IOS configuration option instructs the IPS to compile a signature category named ios_ips into memory
and use it to scan traffic?
R1(config)# ipips signature-category
R1(config-ips-category)# category all
R1(config-ips-category-action)# retired false
R1(config)# ipips signature-category
R1(config-ips-category)# category ios_ips basic
R1(config-ips-category-action)# retired false
R1(config)# ipips signature-category
R1(config-ips-category)# category all
R1(config-ips-category-action)# enabled true
R1(config)# ipips signature-category
R1(config-ips-category)# category ios_ips basic
R1(config-ips-category-action)# enabled true
Bottom of Form
2 Top of Form
Refer to the exhibit. An administrator has configured router R1 as indicated. However, SDEE messages fail to log.
Which solution corrects this problem?
Issue the clear ipipssdee events command to clear the SDEE buffer.
Bottom of Form
3 Top of Form
Which three principles are enabled by a Cisco Self-Defending Network? (Choose three.)
adaptability
collaboration
insulation
integration
mitigation
scalability
Bottom of Form
4 Top of Form
What are two disadvantages of using network IPS? (Choose two.)
Network IPS has a difficult time reconstructing fragmented traffic to determine if an attack was successful.
Network IPS is operating system-dependent and must be customized for each platform.
Network IPS is unable to provide a clear indication of the extent to which the network is being attacked.
Network IPS sensors are difficult to deploy when new networks are added.
Bottom of Form
5 Top of Form
Which access list statement permits HTTP traffic that is sourced from host 10.1.129.100 port 4300 and destined to host
192.168.30.10?
access-list 101 permit tcp 10.1.129.0 0.0.0.255 eq www 192.168.30.10 0.0.0.0 eq www
access-list 101 permit tcp 10.1.128.0 0.0.1.255 eq 4300 192.168.30.0 0.0.0.15 eq www
Bottom of Form
6 Top of Form
Which type of SDM rule is created to govern the traffic that can enter and leave the network based on protocol and
port number?
NAC rule
NAT rule
IPsec rule
access rule
Bottom of Form
7 Top of Form
Refer to the exhibit. When configuring SSH on a router using SDM from the Configure menu, which two steps are
required? (Choose two.)
Choose Additional Tasks > Router Access > SSH to generate the RSA keys.
Choose Additional Tasks > Router Access > VTY to specify SSH as the input and output protocol.
Choose Additional Tasks > Router Properties >Netflow to generate the RSA keys.
Choose Additional Tasks > Router Properties > Logging to specify SSH as the input and output protocol.
Choose Additional Tasks > Router Access > AAA to generate the RSA keys.
Choose Additional Tasks > Router Access > Management Access to specify SSH as the input and output protocol.
Bottom of Form
8 Top of Form
Refer to the exhibit. Which two statements are correct regarding the configuration on switch S1? (Choose two.)
Port Fa0/5 storm control for broadcasts will be activated if traffic exceeds 80.1 percent of the total bandwidth.
Port Fa0/6 storm control for multicasts and broadcasts will be activated if traffic exceeds 2,000,000 packets per
second.
Port Fa0/6 storm control for multicasts will be activated if traffic exceeds 2,000,000 packets per second.
Port Fa0/5 storm control for multicasts will be activated if traffic exceeds 80.1 percent of the total bandwidth.
Port Fa0/5 storm control for broadcasts and multicasts will be activated if traffic exceeds 80.1 percent of 2,000,000
packets per second.
Bottom of Form
9 Top of Form
Refer to the exhibit. Which three things occur if a user attempts to log in four times within 10 seconds using an incorrect
password? (Choose three.)
Subsequent virtual login attempts from the user are blocked for 60 seconds.
During the quiet mode, an administrator can virtually log in from any host on network 172.16.1.0/24.
A message is generated indicating the username and source IP address of the user.
During the quiet mode, an administrator can log in from host 172.16.1.2.
Bottom of Form
10 Top of Form
Which type of Layer 2 attack makes a host appear as the root bridge for a LAN?
LAN storm
VLAN attack
Bottom of Form
11 Top of Form
What occurs after RSA keys are generated on a Cisco router to prepare for secure device management?
All vty ports are automatically configured for SSH to provide secure management.
The general-purpose key size must be specified for authentication with the crypto key generatersa general-keys modulus
command.
The keys must be zeroized to reset secure shell before configuring other parameters.
Bottom of Form
12 Top of Form
An organization has mobile workers who use corporate-owned laptops at customer sites to view inventory and place orders.
Which type of VPN allows these workers to securely access all of the client/server applications of the organization?
Bottom of Form
13 Top of Form
Which two guidelines relate to in-band network management? (Choose two.)
Apply in-band management only to devices that must be managed on the production network.
Implement separate network segments for the production network and the management network.
Bottom of Form
14 Top of Form
Which three commands are required to configure SSH on a Cisco router? (Choose three.)
ip domain-namename in global configuration mode
Bottom of Form
15 Top of Form
An administrator needs to create a user account with custom access to most privileged EXEC commands.
Which privilege command is used to create this custom account?
Bottom of Form
16 Top of Form
Refer to the exhibit. An administrator has configured a standard ACL on R1 and applied it to interface serial 0/0/0 in
the outbound direction. What happens to traffic leaving interface serial 0/0/0 that does not match the configured ACL
statements?
The resulting action is determined by the destination IP address and port number.
The source IP address is checked and, if a match is not found, traffic is routed out interface serial 0/0/1.
The traffic is dropped.
Bottom of Form
17 Top of Form
Which statement describes configuring ACLs to control Telnet traffic destined to the router itself?
The ACL is applied to the Telnet port with the ip access-group command.
Apply the ACL to the vty lines without the in or out option required when applying ACLs to interfaces.
The ACL should be applied to all vty lines in the in direction to prevent an unwanted user from connecting to an
unsecured port.
Bottom of Form
18 Top of Form
Which three statements describe SSL-based VPNs? (Choose three.)
It is impossible to configure SSL and IPsec VPNs concurrently on the same router.
The application programming interface is used to extensively modify the SSL client software.
The primary restriction of SSL VPNs is that they are currently supported only in hardware.
Bottom of Form
19 Top of Form
Refer to the exhibit. What information can be obtained from the AAA configuration statements?
The local database is checked first when authenticating console and Telnet access to the router.
If the TACACS+ AAA server is not available, no users can establish a Telnet session with the router.
If the TACACS+ AAA server is not available, console access to the router can be authenticated using the local
database.
Bottom of Form
20 Top of Form
Which two Cisco IPS management and monitoring tools are examples of GUI-based, centrally managed IPS solutions?
(Choose two.)
Bottom of Form
21 Top of Form
Refer to the exhibit. Which AAA function and protocol is in use in the network?
Bottom of Form
22 Top of Form
Which three OSI layers can be filtered by a stateful firewall? (Choose three.)
Layer 2
Layer 3
Layer 4
Layer 5
Layer 6
Layer 7
Bottom of Form
23 Top of Form
Refer to the exhibit. Based on the SDM screen shown, which two actions will the signature take if an attack is detected?
(Choose two.)
Drop the packet and all future packets from this TCP flow.
Bottom of Form
24 Top of Form
Which three switch security commands are required to enable port security on a port so that it will dynamically learn
a single MAC address and disable the port if a host with any other MAC address is connected? (Choose three.)
switchport port-security
Bottom of Form
25 Top of Form
Which statement describes the SDM Security Audit wizard?
After the wizard identifies the vulnerabilities, the SDM One-Step Lockdown feature must be used to make all
security-related configuration changes.
After the wizard identifies the vulnerabilities, it automatically makes all security-related configuration changes.
The wizard autosenses the inside trusted and outside untrusted interfaces to determine possible security problems
that might exist.
Bottom of Form
26 Top of Form
Which component of AAA is used to determine which resources a user can access and which operations the user is
allowed to perform?
auditing
accounting
authorization
authentication
Bottom of Form
27 Top of Form
Which two protocols allow SDM to gather IPS alerts from a Cisco ISR router? (Choose two.)
FTP
HTTPS
SDEE
SSH
Syslog
TFTP
Bottom of Form
28 Top of Form
Refer to the exhibit. Which AAA command logs the activity of a PPP session?
29 Top of Form
What is a feature of the TACACS+ protocol?
It encrypts the entire body of the packet for more secure communications.
It hides passwords during transmission using PAP and sends the rest of the packet in plaintext.
Bottom of Form
30 Top of Form
Refer to the exhibit. Which interface configuration completes the CBAC configuration on router R1?
R1(config)# interface fa0/0
R1(config-if)# ip inspect INSIDE in
R1(config-if)# ip access-group OUTBOUND in
R1(config)# interface fa0/1
R1(config-if)# ip inspect INSIDE in
R1(config-if)# ip access-group OUTBOUND in
R1(config)# interface fa0/1
R1(config-if)# ip inspect OUTBOUND in
R1(config-if)# ip access-group INSIDE out
R1(config)# interface fa0/0
R1(config-if)# ip inspect OUTBOUND in
R1(config-if)# ip access-group INSIDE in
R1(config)# interface fa0/1
R1(config-if)# ip inspect OUTBOUND in
R1(config-if)# ip access-group INSIDE in
Bottom of Form
31 Top of Form
Refer to the exhibit. Which Cisco IOS security feature is implemented on router R2?
CBAC firewall
Bottom of Form
32 Top of Form
Which Cisco IOS privileged EXEC command can be used to verify that the Cisco IOS image and configuration files
have been properly backed up and secured?
Router# dir
Bottom of Form
33 Top of Form
Which device supports the use of SPAN to enable monitoring of malicious activity?
Cisco NAC
Cisco IronPort
34 Top of Form
Which three statements describe zone-based policy firewall rules that govern interface behavior and the traffic moving
between zone member interfaces? (Choose three.)
Pass, inspect, and drop options can only be applied between two zones.
If traffic is to flow between all interfaces in a router, each interface must be a member of a zone.
Traffic is implicitly prevented from flowing by default among interfaces that are members of the same zone.
To permit traffic to and from a zone member interface, a policy allowing or inspecting traffic must be configured
between that zone and any other zone.
Bottom of Form
35 Top of Form
Refer to the exhibit. Based on the SDM screen shown, which two conclusions can be drawn about the IKE policy being
configured? (Choose two.)
Bottom of Form
36 Top of Form
The use of 3DES within the IPsec framework is an example of which of the five IPsec building blocks?
authentication
confidentiality
Diffie-Hellman
integrity
nonrepudiation
Bottom of Form
37 Top of Form
Which statement describes the operation of the IKE protocol?
It uses TCP port 50 to exchange IKE information between the security gateways.
Bottom of Form
38 Top of Form
Which three types of views are available when configuring the Role-Based CLI Access feature? (Choose three.)
superuser view
root view
superview
CLI view
admin view
config view
Bottom of Form
39 Top of Form
Which statement describes a MAC address table overflow attack?
An attacker alters the MAC address in a frame to match the address of a target host.
Frames flood the LAN, creating excessive traffic and degrading network performance.
The attacking host broadcasts STP configuration and topology change BPDUs to force spanning-tree recalculations.
A software tool floods a switch with frames containing randomly generated source and destination MAC and IP
addresses.
Bottom of Form
40 Top of Form
When configuring a class map for zone-based policy firewall, how are the match criteria applied when using the
match-all parameter?
Traffic must match all of the match criteria specified in the statement.
Bottom of Form
41 Top of Form
Which three statements describe limitations in using privilege levels for assigning command authorization? (Choose three.)
Commands set on a higher privilege level are not available for lower privileged users.
Views are required to define the CLI commands that each user can access.
Creating a user account that needs access to most but not all commands can be a tedious process.
It is required that all 16 privilege levels be defined, whether they are used or not.
Bottom of Form
42 Top of Form
What is an important difference between network-based and host-based intrusion prevention?
Network-based IPS is better suited for inspection of SSL and TLS encrypted data flows.
Network-based IPS provides better protection against OS kernel-level attacks on hosts and servers.
Network-based IPS can provide protection to hosts without the need of installing specialized software on each one.
Bottom of Form
43 Top of Form
Refer to the exhibit. Based on the output from the show secure bootset command on router R1, which three
conclusions can be drawn regarding Cisco IOS Resilience? (Choose three.)
The Cisco IOS image file is hidden and cannot be copied, modified, or deleted.
The Cisco IOS image filename will be listed when the show flash command is issued on R1.
Bottom of Form
44 Top of Form
Which element of the Cisco Threat Control and Containment solution defends against attempts to attack servers by
exploiting application and operating system vulnerabilities?
Bottom of Form
45 Top of Form
Refer to the exhibit. Based on the SDM NTP Server Details screen, which two conclusions can be drawn from the
information entered and check boxes checked? (Choose two.)
NTP messages will be sent and received on interface Serial0/0/0 for this router.
NTP routing updates will be sent and received on interface Serial0/0/0 of the NTP server.
Bottom of Form
46 Top of Form
Which two statements match a type of attack with an appropriate example? (Choose two.)
To conduct an access attack, an attacker uses L0phtCrack to obtain a Windows server password.
To conduct an access attack, an attacker uses Wireshark to capture interesting network traffic.
To conduct a reconnaissance attack, an attacker initiates a ping of death attack to a targeted server.
To conduct a DoS attack, an attacker uses handler systems and zombies to obtain a Windows server password.
To conduct a DoS attack, an attacker initiates a smurf attack by sending a large number of ICMP requests to
directed broadcast addresses.
To conduct a reconnaissance attack, an attacker creates a TCP SYN flood causing the server to spawn many
half-open connections and become unresponsive.
Bottom of Form
47 Top of Form
The use of which two options are required for IPsec operation? (Choose two.)
Bottom of Form
48 Top of Form
Which three security services are provided by digital signatures? (Choose three.)
Bottom of Form
49 Top of Form
Which three statements should be considered when applying ACLs to a Cisco router? (Choose three.)
ACLs always search for the most specific entry before taking any filtering action.
A maximum of three IP access lists can be assigned to an interface per direction (in or out).
An access list applied to any interface without a configured ACL allows all traffic to pass.
Bottom of Form
50 Top of Form
Which consideration is important when implementing syslog in a network?
Enable the highest level of syslog available to ensure logging of all possible event messages.
Log all messages to the system buffer so that they can be displayed when accessing the router.
Synchronize clocks on all network devices with a protocol such as Network Time Protocol.
Bottom of Form