Documente Academic
Documente Profesional
Documente Cultură
EXECISE PROBLEMS
LARGE SAMPLE PROBLEMS
SINGLE MEAN
1. A melting point test of n = 40 samples of a binder used in manufacturing a rocket
propellant resulted in 𝑥̅ = 154.2°F. Assume that the melting point is normally distributed
with σ = 1.5°F. Test H0 :μ = 155 versus H1:μ ≠ 155 using α = 0.01.
2. The number of concurrent users for some internet service provider has always averaged
5000 with a standard deviation of 800. After an equipment upgrade, the average number
of users at 100 randomly selected moments of time is 5200. Does it indicate, at a 5%
level of significance, that the mean number of concurrent users has increased? Assume
that the standard deviation of the number of concurrent users has not changed.
4. A manufacturer is interested in the output voltage of a power supply used in a PC. Output
voltage is assumed to be normally distributed with standard deviation 0.25 volt, and the
manufacturer wishes to test H0: μ = 5 volts against H1: μ ≠ 5 volts, using n = 600units.
Find the power of the test for detecting a true mean output voltage of 5.1 volts at 5% l.o.s.
7. An engineer who is studying the tensile strength of a steel alloy intended for use in golf
club shafts knows that tensile strength is approximately normally distributed with σ = 60
psi. A random sample of 42 specimens has a mean tensile strength of x = 3450 psi. Test
the hypothesis that mean strength is 3500 psi. Use α = 0.01.
9. A manufacturer is interested in the output voltage of a power supply used in a PC. Output
voltage is assumed to be normally distributed with standard deviation 0.25 volt, and the
manufacturer wishes to test H0: μ = 5 volts against H1: μ ≠ 5 volts, using n = 600units.
Find the power of the test for detecting a true mean output voltage of 5.1 volts at 5% l.o.s.
10. The output voltage for an electric circuit is specified to be 130. A sample of 40
independent readings on the voltage for this circuit gave a sample mean 128.6 and
standard deviation 2.1. Test the hypothesis that the average output voltage is 130 against
the alternative that it is less than 130. Use a test with level .05.
SINGLE PROPORTION
1. A manufacturer of interocular lenses will qualify a new grinding machine if there is
evidence that the percentage of polished lenses that contain surface defects is 2%. A
random sample of 250 lenses contains 6 defective lenses. Formulate and test an
appropriate set of hypotheses to determine whether the machine can be qualified. Use α =
0.05.
2. A researcher claims that at least 10% of all football helmets have manufacturing flaws
that could potentially cause injury to the wearer. A sample of 200 helmets revealed that
16 helmets contained such defects. Does this finding support the researcher's claim? Use
α = 0.01.
3. A cell phone company claim that 84% of batteries for cell phones will not discharged
fully in 48 operating hours with proper charging procedures. A study of 5000 batteries is
carried out and 15 stop operating prior to 48 hours. Do these experimental results support
the claim of cell phone company at 5% i.o.s.
5. A computer manufacturer ships laptop computers with the batteries fully charged so that
customers can begin to use their purchases right out of the box. In its last model, 85% of
customers received fully charged batteries. To simulate arrivals, the company shipped
100 new model laptops to various company sites around the country. Of the 105 laptops
shipped, 96 of them arrived reading 100% charged. Do the data provide evidence that this
model’s rate is at least as high as the previous model? Test the hypothesis at α = 0.05.
TWO MEANS
1. Two types of plastic are suitable for an electronics component manufacturer to use. The
breaking strength of this plastic is important. It is known that σ1 = σ2 = 1.0 psi. From a
random sample of size n1 = 100 and n2 = 120, you obtain 𝑥1 ̅̅̅ = 162.5 and 𝑥2
̅̅̅= 155.0. The
company will not adopt plastic 1 unless its mean breaking strength exceeds that of plastic
2 by at least 10 psi. Based on the sample information, should it use plastic 1? Use α =
0.05 in reaching a decision.
2. A product developer is interested in reducing the drying time of a primer paint. Two
formulations of the paint are tested; formulation 1 is the standard chemistry, and
formulation 2 has a new drying ingredient that should reduce the drying time. From
experience, it is known that the standard deviation of drying time is 8 minutes, and this
inherent variability should be unaffected by the addition of the new ingredient. Ten
specimens are painted with formulation 1, and another 40 specimens are painted with
formulation 2; the 50 specimens are painted in random order. The two sample average
drying times are 𝑥1 ̅̅̅ = 121 minutes and 𝑥2̅̅̅ = 112 minutes, respectively. What
conclusions can the product developer draw about the effectiveness of the new
ingredient, using α = 0.05?
4. Tensile strength tests were performed on two different grades of aluminum spars used in
manufacturing the wing of a commercial transport aircraft. From past experience with the
spar manufacturing process and the testing procedure, the standard deviations of tensile
strengths are assumed to be known. The data obtained are as follows: n1 = 40, ̅̅̅
𝑥1 = 87.6,
̅̅̅
σ1 = 1, n2 = 42, 𝑥2 = 74.5, and σ2 = 1.5. Is there any difference in two grades of
aluminum spars at 5% i.o.s.
TWO PROPORTIONS
1. Two different types of injection-molding machines are used to form plastic parts. A part
is considered defective if it has excessive shrinkage or is discolored. Two random
samples, each of size 300, are selected, and 15 defective parts are found in the sample
from machine 1, and 8 defective parts are found in the sample from machine 2. Is it
reasonable to conclude that machine 2 produce less fraction of defective parts, using α =
0.05?
2. Two different types of polishing solutions are being evaluated for possible use in a
tumble-polish operation for manufacturing interocular lenses used in the human eye
following cataract surgery. Three hundred lenses were tumble polished using the first
polishing solution, and of this number, 253 had no polishing-induced defects. Another
300 lenses were tumble-polished using the second polishing solution, and 196 lenses
were satisfactory upon completion. Is there any reason to believe that the two polishing
solutions differ? Use α = 0.01.
3. Out of two weighing machines at a railway station 1st Machine fails to work 13 times in
250 trials. The 2nd Machine fails to work in 7 times in 200 trials. Can we conclude that
second machine failure proportion is less at 5% L.O.S
4. A quality inspector finds 10 defective parts in a sample of 500 parts received from
manufacturer A. Out of 400 parts from manufacturer B, she finds 12 defective ones. A
computer-making company uses these parts in their computers and claims that the quality
of parts produced by A and B is the same. At the 5% level of significance, do we have
enough evidence to disprove this claim?
5. A random sample of 10000 men shows that 8267 favour alliance of DMDK with ADMK
while 10000 women shows that 7824 fvaour the alliance of DMDK with ADMK. Is there
any difference in opinion at 5% i.o.s.
Single Mean
1. High sulfur content in steel is very undesirable, giving corrosion problems among other
disadvantages. If the sulfur content becomes too high, steps have to be taken. Five successive
independent specimens in a steel-making process give values of percentage sulfur of 0.0307,
0.0324, 0.0314, 0.0311 and 0.0307. Do these data give evidence at the 5% level of significance
that the true mean percentage sulfur is above 0.0300.
2. Two chemical processes for manufacturing the same product are being compared under
the same conditions. Yield from Process A gives an average value of 96.2 from six runs, and the
estimated standard deviation of yield is 2.75. Yield from Process B gives an average value of
93.3 from seven runs, and the estimated standard deviation is 3.35. Yields follow a normal
distribution. Is the difference between the mean yields statistically significant? Use the 5% level
of significance, and show rejection regions for the difference of mean yields on a sketch.
3. The average daily amount of scrap from a particular manufacturing process is 25.5 kg
with a standard deviation of 1.6 kg. A modification of the process is tried in an attempt to reduce
this amount. During a 10-day trial period, the kilograms of scrap produced each day were: 25.0,
21.9, 23.5, 25.2, 22.0, 23.0, 24.5, 25.0, 26.1, 22.8. From the nature of the modification, no
change in day-to-day variability of the amount of scrap will result. The normal distribution will
apply. A first glance at the figures suggests that the modification is effective in reducing the
scrap level. Does a significance test confirm this at the 1% level?
Difference of Means
1. Two companies produce resistors with a nominal resistance of 4000 ohms. Resistors from
company A give a sample of size 9 with sample mean 4025 ohms and estimated standard
deviation 42.6 ohms. A shipment from company B gives a sample of size l3 with sample mean
3980 ohms and estimated standard deviation 30.6 ohms. Resistances are approximately normally
distributed.
At 5% level of significance, is there a difference in the mean values of the resistors produced by
the two companies?
2. A new composition for car tires has been developed and is being compared with an older
composition. Ten tires are manufactured from the new composition, and ten are manufactured
from the old composition. One tire of the new composition and one of the old compositions are
placed on the front wheels of each of ten cars. Which composition goes on the left-hand or right-
hand wheel is determined randomly.
The wheels are properly aligned. Each car is driven 60,000 km under a variety of driving
conditions. Then the wear on each tire is measured. The results are:
Do the results show at the 1% level of significance that the new composition gives significantly
Car No. 1 2 3 4 5 6 7 8 9 10
Wear of 2.4 1.3 4.2 3.8 2.8 4.7 3.2 4.8 3.8 2.9
New
Composition
Wear of Old 2.7 1.9 4.3 4.2 3.0 4.8 3.8 5.3 3.7 3.1
Composition
less wear than the old composition?
3. Nine specimens of unalloyed steel were taken and each was halved, one half being sent
for analysis to a laboratory at Delhi and the other half to a laboratory at Bangalore. The
determinations of percentage carbon content were as follows:
Specimen l 2 3 4 5 6 7 8 9
No.
Delhi Lab 0.22 0.ll 0.46 0.32 0.27 0.l9 0.08 0.l2 0.l8
Bangalore 0.20 0.l0 0.39 0.34 0.23 0.l4 0.l3 0.08 0.l6
Lab
Is there any significant difference in mean carbon content tested by two labs at 1% l.o.s.
4. Two flow meters, A and B, are used to measure the flow rate of brine in a potash
processing plant. The two meters are identical in design and calibration and are mounted on two
adjacent pipes, A on pipe 1 and B on pipe 2. On a certain day, the following flow rates (in
m3/sec) were observed at 10-minute intervals from
1:00 p.m. to 2:00 p.m.
Meter A Meter B
1:00 p.m. 1.7 2.0
1:10 p.m. 1.6 1.8
1:20 p.m. 1.5 1.6
1:30 p.m. 1.4 1.3
1:40 p.m. 1.5 1.6
1:50 p.m. 1.6 1.7
2:00 p.m, 1.7 1.9
Is the flow in pipe 2 significantly different from the flow in pipe 1 at the 5% level of
significance?
5. Slaked lime is added to the furnace of an electric power station to reduce the production
of SO2 (a major cause of acid rain). Extensive previous data showed that a standard method of
adding slaked lime reduced SO2 emission by an average percentage of 31.0 with a standard
deviation of 4.70. A test on a new method gives mean percentage removed of 33.5 based on a
sample of size 15 with no change in the standard deviation. Is there evidence at the 1% level of
significance that the new method gives higher removal of SO2 than the standard method?
F- Test
1. Two different lighting techniques are compared by measuring the intensity of light at
selected locations in areas lighted by the two methods. If 15 measurements in the first area had a
SD of 2.7 foot-candles and 21 measurements in the second area had a SD of 4.2 foot-candles, can
it be concluded that the lighting in the second area is less uniform? Use 5% LOS
2. Two different lighting techniques are compared by measuring the intensity of light at
selected locations in areas lighted by the two methods. If 15 measurements in the first area had a
SD of 2.7 foot-candles and 21 measurements in the second area had a SD of 4.2 foot-candles, can
it be concluded that the lighting in the second area is less uniform? Use 5% LOS.
3. The following are the Brinell hardness values obtained for samples of two magnesium
alloys before testing.
Alloy 1: 66.3 63.5 64.9 61.8 64.3 64.7 65.1 64.5 68.4 63.2
Alloy 2: 71.3 60.4 62.6 63.9 68.8 70.1 64.8 68.9 65.8 66.2
Test whether the two samples came from same normal population.
4. The coefficients of thermal expansion of two alloys, A and B, are compared. Six random
measurements are made for each alloy. For alloy A, the coefficients (×106) are 12.95, 14.05,
12.75, 12.10, 13.50 and 13.00. Coefficients (×106) for alloy B are 14.05, 15.35, 14.35, 15.15, 13
85 and 14.25. Assume the values for each alloy are normally distributed. Is the variance of
coefficients for alloy A significantly different from the variance of coefficients for alloy B? Use
the 10% level of significance.
6. A general contractor is considering purchasing lumber from one of two different suppliers. A
sample of 12 boards is obtained from each supplier and the length of each board is measured.
The estimated standard deviations from the samples are s1 = 0.13 inch and s2 = 0.17 inch,
respectively. Assume the lengths follow a normal distribution. Does this data indicate the lengths
of one supplier’s boards are subject to less variability than those from the other supplier? Test
using a level of significance equal to 0.02.
7. Wire of a certain type is supplied to an electrical retailer by each of two manufacturers, A and
B. Users of the wire suggest that there is more variability (from specimen to specimen) in the
resistance of the wire supplied by Company A than in that supplied by Company B. Random
samples of wire from spools of the wire supplied by the two companies were taken. The
resistances were measured with the following results:
Company A B
Number of Samples 13 21
Sum of Resistances 96.8 201.4
Sum of Squares of Resistances 732.30 1936.90
Assume the resistances were normally distributed. Use the results of these samples to determine
at the 5% level of significance whether or not there is evidence to support the suggestion of the
users.
2. The following table gives the two wheeler accidents occurred during one week.
Days: Sun Mon Tue Wed Thu Fri Sat
Accidents: 14 16 8 12 11 9 14
Can you say that the accidents are uniformly distributed over the week? Use 5% LOS.
3. The following table shows the opinions of voters before and after a Prime Minister election.
Before After Total
For Ruling Party 79 91 170
For Opposition Party 84 66 150
Undecided 37 43 80
Total 200 200 400
Test at 5% LOS whether there has been any change of opinion of voters.
Very Good 9 49 63
Use 1% l.o.s to test the hypothesis that is there any relation between performance in the training
and the success in the jobs.
6. Car manufacturers are interested in whether there is a relationship between the size of car
an individual drives and the number of people in the driver’s family (that is, whether car size and
family size are independent). To test this, suppose that 800 car owners were randomly surveyed
with the following results. Conduct a test for independence.