Documente Academic
Documente Profesional
Documente Cultură
(/)
Advertisement
(/wp-content/uploads/2013/07/AM-Receiver.jpg)
AM Receiver Circuit
P. MARIAN (HTTPS://WWW.ELECTROSCHEMATICS.COM/AUTHOR/ADMIN/)
(https://www.facebook.com/sharer/sharer.php?
u=https://www.electroschematics.com/9043/am-receiver-circuit/)
AM radio (/tag/am-radio) radio receivers (/tag/radio-receiver-circuits)
(https://twitter.com/share) (/qa/)
AM Receiver
Share
Notes
Open Project (/)
Q1
R5
10K
R4 C4
560K 0.1uF
C1
L1 R2 R3
500pF
200uH 1K 330
C3
0.1uF Q3
R1
C2 Q2
9V
0.1uF
Application:
A small, simple AM receiver project with only 3 transistors. This circuit can pick
up medium wave stations in your area.
Description:
It can use general purpose transistors, and in this example there are 3 BC109C
transistors. The schematic and BOM show a 200µH inductor and a trimmer
capacitor 150-500pF, though these parts can be salvaged from an old AM radio,
to preserve the directional nature of a tuning coil, and an adjustment knob
(plate capacitor) that work well for radio reception.
The 120k resistor is for regenerative feedback between the Q2 NPN transistor
and the input to the tank circuit. The value of this resistor is important to the
performance of the entire AM receiver. In fact, it may be better to replace the
xed value with a variable resistor paired with a xed resistor to adjust the
oscillation and sensitivity. All the connections should be short to minimize
interference.
much by its construction and its environment, a lot of hand tuning and
experimentation will be fun, instructive, and possibly necessary to make it work
best.
(/)
[learn_more caption=”Click here for Parts List”]
Digi-Key Part
RefDesName Value Part Number Description
Number
[/learn_more]
(https://www.electroschematics.com/wp-content/uploads/2013/07/AM-Receiver.jpg)
Previous
LA4440 Audio Ampli er
(https://www.electroschematics.com/9036/la4440-audio-ampli er/)
Next
Network Cable Tester
(https://www.electroschematics.com/9048/network-cable-tester/)
Related Tutorials
No related posts.
i need to interface r c circuit with the internal ADC pin of pic controller (/qa/10887/)
Recent Posts
10 Comments
divya
thanks for giving a good knowledge
nyni
https://www.electroschemat cs.com/9043/am-rece ver-c rcu t/ 5/12
23.02.2019 AM Rece ver C rcu t
can u explain the function of each component in the circuit please!!! thank u !! ASAP
Larbi
Hi John, I’m glad the mod was useful. I agree that cutnitg the tracks is tricky. It
might be simpler to lift the emitter lead of the transistor and solder the
resistor between it and ground. You could also probably remove the inductor
instead of cutnitg the track on the input. Either way it is a ddly job.I found
replacing the display quite easy. I rst straightened the two top clips with
pliers then screwed the display in place and nally bent the clips again with a
screwdriver. It looks like this is how it was assembled in the factory. Colin.
G4EML.
mohammad
hi
may u say where the speaker’s place is?
there is no sign in the schematic!
yash-verma28gmail-com
the output side u connect the speaker and connect the other end of speaker to
the negative terminal of battery……..
i think it is so good
for ten years ago i try to made good radio but i cannt help me please to send me good
(/)
circuits to do that
Majlinda
Hi all, well I tried the mod out on my uv-5re and while it did increase the
devaition I now have something strange. while the tdr(dual band mode) is on I
am getting a strange pulsating noise. it isn’t in the rx as the squelch is kicked
in and the signal indicator is out. It does stop if I opt out of dual band mode. It
also is producing static from the unit after you tx and I must hit the monitor
button to clear it up. It is similar to the above mentioned issue but without the
pulsating. I left L44 in place and cut the trace as illistrated, And lifted the leg
of Q17 instead of cutting the ground trace and installed the 470 ohm SMD
capacitor from the leg to ground. I am not sure if it is nessassary to cut the
ground trace or not. I am curious if anyone else has seen this issue?Thank you
in advance,M.S.
sahar paware
looks like really applicable.
(/)
i’m going to try this today itself. its nice one.
José Domínguez
Me gustaría que me enviasen las medidas, número de espiras y diámetro del hilo (AWG)
esmaltado para construir la bobina de 200 uH.
Login
Email
Password
Remember Me
Log In
View More ()
New Projects
Mains Power Failure Alert Circuit (https://www.electroschematics.com/14331/mains-power-
failure-alert-circuit/)
Recent Q&A
Can NE/SA575 chan 1 be used as ALC? (/qa/10916/)
https://www.electroschemat cs.com/9043/am-rece ver-c rcu t/ 9/12
23.02.2019 AM Rece ver C rcu t
(/)
ripple voltage (/qa/10888/)
i need to interface r c circuit with the internal ADC pin of pic controller (/qa/10887/)
Download
Datasheets
POWERED BY DATASHEETS.COM
Part Number
e.g. LM317
Search
(/subscribe)
(https://www.facebook.com/groups/electroschematics/)
(/)
THE BASICS
About Us
Contact Us (https://www.electroschematics.com/contact-us/)
Participate (https://www.electroschematics.com/participate/)
Feedback (https://www.surveymonkey.com/r/2SMMN52)
FOR ADVERTISERS
ASPENCORE NETWORK
GLOBAL NETWORK
Facebook (https://www.facebook.com/groups/electroschematics/)
Youtube (https://www.youtube.com/user/ElectroSchematics)
All contents are Copyright © 2019 by AspenCore, Inc. All Rights Reserved.