Documente Academic
Documente Profesional
Documente Cultură
TA8277H
Max Power 43 W BTL × 4 ch Audio Power IC
Features
Weight: 7.7 g (typ.)
· High power : POUTMAX (1) = 43 W (typ.)
(VCC = 14.4 V, f = 1 kHz, JEITA max, RL = 4 Ω)
: POUTMAX (2) = 40 W (typ.)
(VCC = 13.7 V, f = 1 kHz, JEITA max, RL = 4 Ω)
: POUT (1) = 28 W (typ.)
(VCC = 14.4 V, f = 1 kHz, THD = 10%, RL = 4 Ω)
: POUT (2) = 24 W (typ.)
(VCC = 13.2 V, f = 1 kHz, THD = 10%, RL = 4 Ω)
· Low distortion ratio: THD = 0.02% (typ.)
(VCC = 13.2 V, f = 1 kHz, POUT = 5 W, RL = 4 Ω)
· Low noise: VNO = 0.10 mVrms (typ.)
(VCC = 13.2 V, Rg = 0 Ω, GV = 26dB, BW = 20 Hz~20 kHz)
· Built-in stand-by switch function (pin 4)
· Built-in muting function (pin 22)
· Built-in AUX amplifier from single input to 4 channels output (pin 16)
· Built-in various protection circuit
: Thermal shut down, over voltage, out to GND, out to VCC, out to out short
· Operating supply voltage: VCC (opr) = 9~18 V
1 2002-02-13
TA8277H
Block Diagram
C5
C3
1 20 6
TAB VCC1 VCC2
OUT1 (+)
9
IN1
11 PW-GND1 8 RL
C1
OUT1 (-)
7
OUT2 (+)
5
IN2
12 PW-GND2 2 RL
C1
OUT2 (-)
3
AUX IN
16
C6
OUT3 (+)
17
IN3
15 PW-GND3 18 RL
C1
OUT3 (-)
19
OUT4 (+)
21
IN4
14 PW-GND4 24 RL
C1
OUT4 (-)
23
PRE-GND
13
R2
C7
C8
R1
C4
: PRE-GND
: PW-GND
2 2002-02-13
TA8277H
Caution and Application Method
(Description is made only on the single channel.)
Amp. 2A
Amp. 1
Input
Amp. 2B
ON OFF 0~1.5
OFF ON 3~VCC Figure 2 With pin 4 set to High,
Power is turned ON
Adjustage of Stand-by SW
(1) Since VCC can directly be controlled to ON or OFF by the microcomputer, the switching relay can be
omitted.
(2) Since the control current is microscopic, the switching relay of small current capacity is satisfactory
for switching
3 2002-02-13
TA8277H
RELAY
Large current capacity switch
BATTERY BATTERY
– Conventional Method –
DIRECTLY FROM
Small current capacity switch MICROCOMPUTER
BATTERY BATTERY
Figure 3
ATT – VMUTE
0
-10
R1 = 5 kW
-20
(dB)
-50
R1 A -60
22
-70
VCC = 13.2 V
C4
IMUTE -80 Po = 10 W
VMUTE RL = 4 W
-90
f = 1 kHz
-100
1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8
4 2002-02-13
TA8277H
4. AUX Input (pin 16) 20dB AMP.
The pin 16 is for input terminal of AUX
amplifier.
The total gain is 0dB by using of AUX amplifier. IN
Therefore, the m-COM can directly drive the OUT (+)
AUX amplifier.
BEEP sound or voice synthesizer signal can be
input to pin 16 directly. OUT (-)
When AUX function is not used, this pin must be AUX AMP
AUX-IN
connected to PRE-GND (pin 13) via a capacitor. m-COM 16
-20dB
5 2002-02-13
TA8277H
Maximum Ratings (Ta = 25°C)
Electrical Characteristics
(unless otherwise specified, VCC = 13.2 V, f = 1 kHz, RL = 4 W, Ta = 25°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Quiescent current ICCQ ¾ VIN = 0 ¾ 200 400 mA
POUT MAX (1) ¾ VCC = 14.4 V, max Power ¾ 43 ¾
POUT MAX (2) ¾ VCC = 13.7 V, max Power ¾ 40 ¾
Output power W
POUT (1) ¾ VCC = 14.4 V, THD = 10% ¾ 28 ¾
POUT (2) ¾ THD = 10% 22 24 ¾
Total harmonic distortion THD ¾ POUT = 5 W ¾ 0.02 0.2 %
Voltage gain GV ¾ VOUT = 0.775 Vrms (0dBm) 24 26 28
dB
Voltage gain ratio DGV ¾ VOUT = 0.775 Vrms (0dBm) -1.0 0 1.0
VNO (1) ¾ Rg = 0 W, DIN45405 ¾ 0.12 ¾
Output noise voltage mVrms
VNO (2) ¾ Rg = 0 W, BW = 20 Hz~20 kHz ¾ 0.10 0.35
frip = 100 Hz, Rg = 620 W
Ripple rejection ratio R.R. ¾ 40 50 ¾ dB
Vrip = 0.775 Vrms (0dBm)
Rg = 620 W
Cross talk C.T. ¾ ¾ 65 ¾ dB
VOUT = 0.775 Vrms (0dBm)
Output offset voltage VOFFSET ¾ ¾ -150 0 +150 mV
Input resistance RIN ¾ ¾ ¾ 90 ¾ kW
Stand-by current ISB ¾ Stand-by condition ¾ 2 10 mA
VSB H ¾ Power: ON 3.0 ¾ VCC
Stand-by control voltage V
VSB L ¾ Power: OFF 0 ¾ 1.5
VM H ¾ Mute: OFF Open ¾
Mute control voltage (Note2)
VM L ¾ Mute: ON, R1 = 10 kW 0 ¾ 0.5 V
Mute: ON,
Mute attenuation ATT M ¾ VOUT = 7.75 Vrms (20dBm) at 80 90 ¾ dB
Mute: OFF.
Note 2: Muting function have to be controlled by open and low logic, which logic is a transistor, FET and m-COM port
of IMUTE > 50 mA ability.
This means than the mute control terminal : pin 22 must not be pulled-up.
6 2002-02-13
TA8277H
Test Circuit
0.1 mF
3900 mF
C5
C3
1 20 6
TAB VCC1 VCC2
OUT1 (+)
9
0.22 mF IN1
11 PW-GND1 8 RL
C1
OUT1 (-)
7
OUT2 (+)
5
0.22 mF IN2
12 PW-GND2 2 RL
C1
OUT2 (-)
3
0.22 mF AUX IN
16
C6
OUT3 (+)
17
0.22 mF IN3
15 PW-GND3 18 RL
C1
OUT3 (-)
19
OUT4 (+)
21
0.22 mF IN4
14 PW-GND4 24 RL
C1
OUT4 (-)
23
PRE-GND
13
C8 0.1 mF
R2 10 kW
C2 10 mF
C4 33 mF
R1 5 kW
: PRE-GND
: PW-GND
7 2002-02-13
TA8277H
(%)
10 10
T.H.D
T.H.D
5 5
3 3
VCC = 9.0 V
Total harmonic distortion
0.5 0.5
0.3 0.3
16.0 V
0.1 0.1
1 kHz
0.05 0.05
0.03 0.03
100 Hz
0.01 0.01
0.1 0.3 0.5 1 3 5 10 30 50 100 0.1 0.3 0.5 1 3 5 10 30 50 100
RL = 4 W
(mA)
POUT = 5 W
T.H.D
300
ICCQ
1
Total harmonic distortion
Quiescent current
200
0.1
100
0 0.01
0 10 20 30 10 100 1k 10 k 100 k
Power supply voltage VCC (V) Frequency f (Hz)
8 2002-02-13
TA8277H
VNO – Rg R.R. – f
300 0
VCC = 13.2 V VCC = 13.2 V
(mVrms)
RL = 4 W
200
-30
Output noise voltage
150
-40
100
-50
50
-60
0 -70
0 100 1k 10 k 100 k 0 100 1k 10 k 100 k
Singnal source resistance Rg (9) Frequency f (Hz)
C.T. (dB)
-20 RL = 4 W -20 RL = 4 W
-30 -30
Cross talk
Cross talk
-40 -40
-70 -70
0 100 1k 10 k 100 k 0 100 1k 10 k 100 k
Frequency f (Hz) Frequency f (Hz)
C.T. (dB)
-20 RL = 4 W -20 RL = 4 W
-30 -30
Cross talk
Cross talk
-40 -40
OUT4 ® OUT1, 2
OUT3 ® OUT1, 2 OUT3 ® OUT1, 2
-50 -50
OUT3 ® OUT4
OUT3 ® OUT4
-60 -60 OUT4 ® OUT3
-70 -70
0 100 1k 10 k 100 k 0 100 1k 10 k 100 k
Frequency f (Hz) Frequency f (Hz)
9 2002-02-13
TA8277H
GV – f PD – POUT
40 70
35
60
(W)
(dB)
30
50 16 V
PD
GV
25
Power dissipation
40
Voltage gain
20
13.2 V
30
15
20
10
VCC = 13.2 V f = 1 kHz
9V
5 RL = 4 W 10
RL = 4 W
VOUT = 0.775 Vrms (0dBm)
0 0
0 100 1k 10 k 100 k 0 5 10 15 20 25
PD MAX – Ta
120
(W)
40
20 ②
③
0
0 25 50 75 100 125 150
Ambient temperature Ta (°C)
10 2002-02-13
TA8277H
Package Dimensions
11 2002-02-13
TA8277H
· TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc..
· The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this
document shall be made at the customer’s own risk.
· This product generates heat during normal operation. However, substandard performance or malfunction may
cause the product and its peripherals to reach abnormally high temperatures.
The product is often the final stage (the external output stage) of a circuit. Substandard performance or
malfunction of the destination device to which the circuit supplies output may cause damage to the circuit or to the
product.
· The products described in this document are subject to the foreign exchange and foreign trade laws.
· The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other
rights of the third parties which may result from its use. No license is granted by implication or otherwise under
any intellectual property or other rights of TOSHIBA CORPORATION or others.
12 2002-02-13