Documente Academic
Documente Profesional
Documente Cultură
Foreword
Thanks for choosing BYD F3/F3R. To help you operate and maintain BYD F3/F3R, please read this Owner's Manual thoroughly.
BYD F3 uses electric injection engine, and the wiring harness is very complex, so please do not install the following additional electric equipment by
yourself: burglar alarm, central control lock, power window, audio devices and so on. Any damages or malfunctions caused by the above
modifications are not covered by warranty.
Throughout this manual, you will see safety and vehicle damage warnings. You must follow these warnings carefully to avoid possible injury or
damage.
The types of warning, what they look like, and how they are used in this manual are explained as follows:
Important Information
CAUTION
This is a warning against anything which may cause injury to people or
damages to your vehicle.
NOTICE
Be convenient to overhaul, please abide the following.
All pictures in this manual are schematic and only for references.
BYD reserves the right to modify the technical features and When you see the safety symbol shown above, it means:
specifications in this manual without notice. “Do not …”; “Do not do this”; or “Do not let this happen”.
Thanks for choosing BYD F3/F3R. All suggestions are welcome.
F3/F3R OWNER’S MANUAL
CONTENTS
-1-
F3/F3R OWNER’S MANUAL
* The actual fuel consumption depends on many factors, like vehicle condition, road condition,
and driving habit.
Technical specifications of BYD F3R
-2-
F3/F3R OWNER’S MANUAL
-3-
F3/F3R OWNER’S MANUAL
BYD F3 vehicle identification The VINs are set in the engine cabin
VIN: separately and on the upper left of the
panel, as shown
n in Figure 1. This is the
VIN of BYD-F3 for the car owner to
register. The Plate-2 shows the VIN as
well.
1 2 3 4
-4-
F3/F3R OWNER’S MANUAL
The picture above refers to children- Engine No. (4G1 series engine) CNG bottle alarm plate
protection system indication which is As showed in the picture above, the
downward to the children-protection number of Engine is indicated on the
lock on the inner side of the rear door. cylinder.
-5-
F3/F3R OWNER’S MANUAL
The picture above shows the tire Engine No. (473 series engine)
pressure indication which is set As showed in the picture above, the
below the lock ring of left front number of Engine is indicated on the
door cylinder.
-6-
F3/F3R OWNER’S MANUAL
-7-
F3/F3R OWNER’S MANUAL
-7-
9. Console box(Option)
10. Rear ashtray(Option)
11. Parking control assembly
12. Gear shift lever(MT)
13. Auxiliary box
14. Hook lock release lever
15. Power window lock switch(Option)
16. Central door lock switch(Option)
-8-
F3/F3R OWNER’S MANUAL
-9-
F3/F3R OWNER’S MANUAL
- 10 -
F3/F3R OWNER’S MANUAL
- 11 -
F3/F3R OWNER’S MANUAL
- 12 -
F3/F3R OWNER’S MANUAL
- 13 -
F3/F3R OWNER’S MANUAL
Indicator symbols on the combined instrument
Low engine oil pressure warning indicator* Headlight high beam indicator
The indicators marked with * are service reminder indicators. For details, please see “Instrument and service reminder indicators” in Section 1-5.
Indicator symbols on the combined instrument (AT)
- 14 -
F3/F3R OWNER’S MANUAL
Reverse indicator
Driver’s seat belt reminder light* SRS warning light*
light(AT)
Neutral indicator
Discharge warning light * Tail light indicator *
light(AT)
The indicators marked with * are service reminder indicators. For details, please see “Instrument and Service reminder indicators” insection 1-5.
- 15 -
F3/F3R OWNER’S MANUAL
SECTION 1-2
OPERATION OF INSTRUMENTS AND CONTROLS
- 16 -
F3/F3R OWNER’S MANUAL
Keys As the key is not needed when you should smash the
locking the door, please take a master key smallest window and open the door. In this
with yourself for spare use when your keys way, the cost will be very cheap. Pay
are locked in the car accidentally attention to the cullet, avoiding being injured.
Side doors
Vehicles with the central door lock system. All before closing the door. The outside door
doors lock and unlock simultaneously with handle must be held up while front doors are
Move the lock knob. To lock: push the rear of the switch
To unlock: pull the knob backward All the doors lock or unlock simultaneously.
To lock: push the knob forward Unlocking and locking the door
If you want to lock the door from the
automatically
outside, set the knob in the lock position
- 18 -
F3/F3R OWNER’S MANUAL
When the speeds reach to 20km/h, all doors Rear door child protector CAUTION
Move the lock lever to the “LOCK” position as
will be locked automatically. Before driving, be sure that the doors
shown in the figure.
When you turn the ignition key from “ON” to are closed and locked, especially
When the child-protector is locked, you can
“ACC” or “LOCK”, all doors will be opened. when small children are in the
not open the rear door via the inside door
You can cancel these functions. For details, vehicle. Along with proper use of seat
handle. We recommend using this feature
see the section “Settings of optional belts, locking the doors helps
when ever small child are in the vehicle.
functions”. prevent the driver and passengers
from being thrown out from the
.
vehicle in an accident. It also helps
prevent the doors from being opened
unintentionally.
- 19 -
F3/F3R OWNER’S MANUAL
The wireless remote control system is If the wireless remote control does not
designed to lock or unlock all the side actuate the doors, or can not operate from a
doors and back door in the distance of 1 normal distance, or the indicator on the key
m or so. is dimmed or does not illuminate,
please do the following actions:
To operate any switch, push it slowly ●Check for closeness to a radio
and securely. At this time, the indicator transmitter such as a radio station or an
flashes once. airport which can interfere with normal
Observe the following instructions to avoid operation of the key.
damages: ●The battery may have been consumed.
●Do not leave the key in places where the Check the battery inside the transmitter.
temperature becomes high such as on the Replace the battery. For details, see
dashboard. “Replacing the battery in the remote control”.
- 20 -
F3/F3R OWNER’S MANUAL
If you lose your wireless remote control key, be locked. At the same time, the horn will Cancel warning:
contact your BYD AUTO buzz one time to make a warning while the vehicle is under the state of anti-
service station as soon as possible. without entering the anti-theft mode. theft, the warning system is activated.
Press the “LOCK” switch, and all of
“LOCK” switch When the forth (fifth for F3R) door is closed
the doors will be locked one time. At the
If the switch is kept being pressed, the but do not in the state of anti-theft, press the
same time, the warning will be cancelled. In
operation is not repeated. Release the switch “LOCK” switch to lock the door.
this way, the vehicle is also under the
and then push again for another operation.
anti-theft state.
To lock: push the “LOCK” switch, all the side Finding the vehicle: when the vehicle enters
doors and back door are locked the state of anti-theft, press the “LOCK” “UNLOCK” SWITCH
simultaneously. At this time, the turn signal switch and you will hear a buzz and watch the If the switch is kept being pressed, the
lights flash once. turn signal light flashes 15 seconds. (When operation is not repeated. Release the switch
If the key is in the ignition switch, locking and you do not ensure the position of your vehicle, and then push again for another operation.
unlocking can not performed by the remote you can use this feature to find your vehicle.)
control. If the key is not in the ignition switch Under the state of finding the vehicle, press To unlock: press the “UNLOCK”
and no doors are locked, press the “LOCK” the “LOCK” switch again to switch, and all doors will be unlocked while
button on the remote control, and the forth enter this state again. the turn signal light will flash
(fifth for F3R) door will
- 21 -
F3/F3R OWNER’S MANUAL
twice. If you press this switch when the functions”.) warning and enable the turn signal light to
vehicle is under the state of anti-theft, the You have 30 seconds to open a door after flash. The warning lasts about 30 seconds. If
vehicle will be unlocked and the turn signal using the wireless remote control unlock you want to stop this warning within the 30
light will flash three times. feature. If a door is not opened by then, all seconds, you can press “UNLOCK” once or
You can not unlock the vehicle by pressing the doors will be automatically locked again. “PANIC” again (Please do
the “UNLOCK” switch if not press this switch during driving).
the key is in the ignition switch. If under the Quit the anti-theft state:
state of anti-theft and the key is in the ignition when the car is in the anti-theft state Replacing the battery in the remote
switch, pressing the “UNLOCK” switch can (including that the anti-theft warning is on), control
exit from the state of anti-theft and open all of press “UNLOCK” switch and all the doors will For replacement, use two CR2016 lithium
be open once with the turning light flash for
the doors simultaneously. batteries or the equivalent. It
three times. At the same time,
While using the wireless remote control to is recommended to go to BYD AUTO service
the car will quit the anti-theft state.
open the key, the rear inner station to replace it.
light and ignition switch reminder
light will be on for 30 seconds, and
“PANIC” switch
then off. (This function is optional.
Press the “PANIC” switch for 1.5 seconds or
For details, see “Settings of optional
longer at any time to start intermittent
- 22 -
F3/F3R OWNER’S MANUAL
CAUTION
NOTICE NOTICE
● Make sure the positive side and ● Don’t change emission frequency,
After replacing the battery, check whether the
negative side of the battery are
key operates properly. If the key still does not increase the emission power
faced correctly.
● Do not replace the batteries with operate properly, contact your BYD AUTO (including installing frequency
wet hands. Water may cause
service station. amplifier), or install other antenna
unexpected rust.
● Do not touch or move any by yourself.
components inside the ● Don’t bring baleful disturbance to
transmitter, or it may interfere Specification of the remote control
with proper operation. legal wireless communications.
Frequency range: 314.9-315.1 MHz
● Be careful not to bend the Upon disturbance, stop using it and
electrode when inserting the Emission power: ≤5500 μV/m
contact with BYD AUTO service
battery and that dust or oils do
Spurious emission threshold: ≤610μV/m
not adhere to the case. station to eliminate disturbance.
● Close the cover securely. Bandwidth: ≤300 kHz
● Don’t use it on airplane or around
the airport.
- 24 -
F3/F3R OWNER’S MANUAL
- 25 -
F3/F3R OWNER’S MANUAL
F3 F3R
CAUTION
- 26 -
F3/F3R OWNER’S MANUAL
CAUTION
- 28 -
F3/F3R OWNER’S MANUAL
Engine hood
Before driving, be sure that the hood is 2. In front of the vehicle, pull up the supporting rod into the slot
closed and securely locked. auxiliary catch lever and lift the hood. Before closing the hood, check whether you
left any tools or rags inside. Return the
Otherwise, the hood may open
supporting rod to its clip. Then, lower the
unexpectedly while driving and an
hood and make sure that it locks into place. If
accident may occur.
necessary, press down gently on the front
edge to lock it.
- 29 -
F3/F3R OWNER’S MANUAL
function, change the function mode first. For and the actions:
details, see “Settings of optional functions”. ● If the anti-theft system is deactivated,
If you take the key out, close the side doors, the turn signal lights will flash twice.
and do not operate the wireless remote ● If the anti-theft system is activated, the
control in 30 seconds, the vehicle will enter turn signal lights will flash three times,
the anti-theft state automatically. At this time, and the anti-theft indicator light will flash
inserting the key into the ignition switch will quickly. When the ignition key is turned
Press the “LOCK” switch and the manual cause an alarm. When the key is at the “ON” to the “ON” position, the indicator light
anti-theft setting will be exited in 1 second. position, the anti-theft state will be quitted will be off.
The indicator will flash slowly. automatically. You can also press the After you quit the anti-theft state, the rear
In the following situations, the anti-theft state “UNLOCK” switch to quit the state. interior light and ignition key reminder light
can not be enabled: Cancel the state of anti-theft will be on for about 30 seconds go off even
● Any one door is opened. Press the “UNLOCK” switch, and all of the when the doors are closed. The delay time
The buzzer will buzz for about 1 second. doors will be opened while the can be modified. For details, see the
Close the door and try again. vehicle quit the anti-theft mode. “Settings of optional functions”.
Automatic setting of the function If you can not quit the anti-theft mode by
This is an optional function. To use this The relations between the system state using wireless remote control, you
- 31 -
F3/F3R OWNER’S MANUAL
can use the key to cancel it: within the 15 ● The vehicle is knocked. functions”.
seconds when the doors are opened, turn the
ignition key from “ACC” to “ON” ten times, Dual-testing function Restarting the warning
and the state will be disabled. This feature is realized through the dual The warning will restart on the following
After the anti-theft state is disabled, all of the testing below. conditions after warning stops
doors will be locked again, and the vehicle ● A beep will be sent as an alarm upon a
will enter the anti-theft state again if any one light knock in anti-theft mode. Any door being open.
door If your vehicle detects a light knock in 10 Key being turned to “Start”
is not opened. seconds in anti-theft mode, it will warn by position.
Starting the anti-theft warning buzzing with the turning lights flashing for 30 Your vehicle will alarm by buzzing with the
When the anti-theft system detects an seconds. turning lights flashing for 30 seconds and
abnormal condition, the signal light will flash ● A beep will be sent as an alarm and the pausing for 15 seconds. This action circulates
and the warning will be on for 30 seconds. turning lights will flash for 30 seconds for three times.
● Any door is opened. upon a heavy knock in anti-theft mode. The cycle can be changed. Refer to “Settings
● The key is in “ignition” position. The alarm sensitivity against knocks can be of optional functions” for details.
● Reconnect the battery or anti-theft regulated. For details, see the corresponding
module. part in “Steps for changing optional Resetting of anti-theft system
- 32 -
F3/F3R OWNER’S MANUAL
If the anti-theft system does not stay in the For details, see the “Automatic locking and automatically. If 6 and 9
unlocking”.
states said above, the alarm stops after the warning cycles are disabled, 3 warning cycles
● On-board illuminating system
cycle. Then, the system will be reset will be enabled again.
For details, see the “Rear interior light” and
automatically when the auto set function is ● Delay time of entering the vehicle
the “Ignition switch reminder light”.
selected. (15s)
● Starting 6 warning cycles
After using the wireless remote control to
When the vehicle enters the anti-theft state,
Stopping the warn open all doors, the rear interior light and
an alarm will be sent and the turn signal lights
While warning, press “LOCK” to stop it with ignition key reminder light will be on for about
will flash 30
the anti-theft system still working. 15 seconds (original time: 30 seconds). If
seconds. A cycle will be performed every 15
While warning, press “UNLOCK” to selected, the default time, 30 seconds, will be
seconds. Three cycles are defaulted. You
stop it with the anti-theft system not working. disabled.
can choose 6 cycles. If so, 3 and 9 warning
● Delay time of entering the vehicle (30)
cycles are cancelled automatically. If 6 and 9
Settings of optional anti-theft functions After using the wireless remote control to
warning cycles are disabled, 3 warning cycles
Optional anti-theft functions: open all doors, the rear interior light and
will be enabled again.
● Automatic setting function ignition key reminder light will be on for about
● Starting 9 warning cycles
For details, see the “Automatic setting 30 seconds. To use this function, deselect
function”. Select this item to enable 9 warning cycles.
the 15s option first. If both options are
● Automatic locking and unlocking Then, 3 and 6 warning cycles are cancelled
- 33 -
F3/F3R OWNER’S MANUAL
selected, the system will set the time to be 15 6. Press the “LOCK” switch on the wireless Press
Optional function
seconds automatically. remote control according to the following LOCK
tables, and make sure that the indicator once Automatic setting
Steps for changing optional functions flashes. functions
1. Check whether the anti-theft system is Make sure the function state by pressing the twice Automatic locked and
released. “LOCK” switch on the wireless remote control. unlocked
2. Close all of the doors. While the function is chosen, the turn signal 3 times On-board light system
3. Insert the key into the ignition switch. light will flash once and you can hear the 4 times Starting 6 cycles warning
4. Open and close the driver’s door twice warning sound once. To deselect this 5 times Starting 9 cycles warning
within 10 seconds. (close→ function, open any a door and close it. If you
open→close→open→close) find the turn signal 6 times The delay time of
5. Turn the key from “ACC” to light flash twice hear the warning sound twice, entering the vehicle:15s
“ON” three times. (ACC→ON→ACC→ON it indicates that the function is disabled. If 7 times The delay time of
→ACC→ON→ACC) failed, re-open the door and close it again to entering the vehicle:30s
Now the anti-theft indicator light from disabled state to enabled state. standard
illuminates.
- 34 -
F3/F3R OWNER’S MANUAL
The sensitivity can be set in 4 grades: 1st ● Close the driver’s door for 30 seconds.
grade, 2nd grade, 3rd grade, and 4th grade. ● Press the “LOCK” switch on wireless
The 1st grade is most sensitive while the remote control again.
other grades feature a much less sensitivity
For details, please contact your BYD AUTO
in turn. While the vibration sensitivity
service station.
standard is selected, the turn signal light
corresponding to the grade will Fuel tank cap
flash and the warning sound corresponding to
the grade will be given. 1. To open the fuel filler door, pull the
Changing sensitivity standards: lever up.
After entering the vibration sensitivity When refueling, turn off the engine.
standard, you can open and then close any
door to step to the next grade.
- 35 -
F3/F3R OWNER’S MANUAL
CAUTION CAUTION
- 36 -
F3/F3R OWNER’S MANUAL
Electric sun roof (optional) Tilting operation Therefore, release the switch and then push
To operate the sun roof, use the switches it again to close it completely.
beside the front interior light.
The sun roof works when the ignition key is in Tilting operation:
the “ON” position. To tilt up: push the switch on the “UP” side.
The sun shade can be opened or
To lower: push the switch on the opposite
closed by hand.
side of the “UP” side.
Sliding operation:
You may stop the sun roof at any desired
To open: push the switch on the “SLIDE”
Sliding operation position. The roof will move while the switch
side.
is being pushed and stop when released.
The sun shade will be opened together with
the roof.
- 37 -
F3/F3R OWNER’S MANUAL
CAUTION
● While the vehicle is moving, always
keep the heads, hands and other
parts of the bodies of all occupants
away from the roof opening.
Otherwise, they could be seriously
injured if the vehicle stops suddenly
or if the vehicle is involved in an
accident.
● Before you close the sun roof, always
make sure nobody places his or her
head, hands, and other parts of the
body in the roof opening. Otherwise,
someone will be serious injured.
● Do not let any passenger (esp.
children) stay in the car when the
ignition key is inserted in case he/she
will touch sunroof switch and get
stuck. Passengers that nobody is
taking care, especially children, may
be involved in an accident.
- 38 -
F3/F3R OWNER’S MANUAL
SECTION 1-3
OPERATION OF INSTRUMENTS AND CONTROLS
- 39 -
F3/F3R OWNER’S MANUAL
- 40 -
F3/F3R OWNER’S MANUAL
- 41 -
F3/F3R OWNER’S MANUAL
Folding rear seat (F3, option) If necessary, each seat back can be folded
CAUTION
separately.
When the back seat is unfolded, to
Folding rear seat (F3R, option)
prevent occupants from injuring in the
event of an accident or emergency
brake, please obey measures as
following:
● Pull the back seat forward and
backward to make sure it has been
firmly locked, and the red mark on
the button can not be seen.
Otherwise, normal operation of the
safety belts may be affected.
● Make sure the safety belt has not
Pull upward the back seat handle to unlock been twisted or block in the back
seat. Then, put them in the right
the seat, and fold down it. Pull upward the back seat belts to unlock the
position for use.
In this way, the luggage compartment can be seat, and fold down it.
widened till the back of the front seats. For In this way, the luggage compartment can be
precaution when loading luggage, see widened till the back of the front seats. For
precaution when loading luggage, see
“Luggage storage precautions” in Section 2. “Luggage storage precautions” in section 2.
- 42 -
F3/F3R OWNER’S MANUAL
Integral back seat (F3, option) Seat belt precautions: properly, the force of the rapid inflation of the
Integral back seat can not been folded. BYD AUTO strongly urges that the driver and airbag may
passengers in the vehicle be properly cause death or serious injury to the child.
Rear armrest (option) restrained at all times with the seat belts Do not allow the child to stand up or kneel on
provided. Failure to do so could increase the either rear or front seats. An unrestrained
chance of injury and/or the severity of injury child could suffer serious injury or death
in accidents. during emergency braking or a collision. Also,
The seat belts provided for your vehicle are do not let the child sit on your lap. It does not
designed for people of adult size, large provide sufficient restraint.
enough to properly wear them.
Children must be sit in the rear seat and use
the seat belts. According to accident statistics,
CAUTION
the child is safer when properly restrained in
During driving, passengers must sit at
To use the armrest, pull it out as shown the rear seat than in the front seat.
seats, and fasten seat belts well.
above. If a child must sit in the front seat, the seat
Otherwise, injures or deaths may be
Seat belts belt should be worn properly. If an accident
easily caused when there is emergency
occurs and the seat belts are not worn
braking and collision.
- 43 -
F3/F3R OWNER’S MANUAL
When using the seat belts, observe the disassemble or modify the system.
● Keep the belts clean and dry. If they need
following:
cleaning, use a mild soap solution or
● Use the belt for only one person at a time. lukewarm water. Never use bleach, dye, or
Do not use a single belt for two or more abrasive cleaners which may severely
people, even children. weaken the belts. (See “Cleaning the
interior” in Section 5.)
● Avoid reclining the seatback any more than
● Replace the belt assembly (including bolts)
needed. The seat belts provide maximum if it has been used in a severe impact. The Adjust the seat as needed and sit up
protection in a frontal or rear collision when entire assembly should be replaced even if straight and well back in the seat.
the damage is not obvious. To fasten your belt, pull it out of the
the driver and the front passenger are
CAUTION retractor and insert the tab into the
sitting up straight and well back in the
The safety belts are designed only for buckle.
seats. You can refer to the You will hear a click when the tab locks into
adults, not suitable for children.
descriptions about seat adjustment. the buckle.
Children must be seated in the rear seat. The seat belt length automatically adjusts to
● Be careful not to damage the belt webbing
3-point seat belts your size and the seat position.
or hardware. Take care that they do not get The retractor will lock the belt during a
caught or pinched in the seat or doors. sudden stop or on impact. It also may lock if
● Inspect the belt system periodically. Check you lean forward too quickly. A slow, easy
for cuts, fraying, and loose parts. Damaged motion will allow the belt to extend, and you
parts should be replaced. Do not can move around freely.
- 44 -
F3/F3R OWNER’S MANUAL
- 45 -
F3/F3R OWNER’S MANUAL
CAUTION CAUTION
Both high-positioned and loose-fitting ● After inserting the tab, make sure the
lap belts could cause serious injuries tab and buckle are locked and that
due to sliding under the lap belt during a the belt is not twisted.
collision or other unintended result. ● Do not insert coins, clips, etc. in the
Keep the lap belt positioned as low on buckle as this may prevent you from
hips as possible. properly latching the tab and buckle.
● If the seat belt does not function
Remove excess length of the belt and normally, immediately contact BYD
adjust the belt position. AUTO service station. Do not use the
To shorten the belt, pull the free end of the seat until the seat belt is fixed. It can
belt. not protect an adult occupant or
Position the loin belt as low as possible on your child from injury.
your hips, not on your loin. Then, adjust it to a
snug fit.
- 47 -
F3/F3R OWNER’S MANUAL
- 48 -
F3/F3R OWNER’S MANUAL
- 49 -
F3/F3R OWNER’S MANUAL
for 5 seconds above. This means that when the ignition key is turned Conditions of activating SRS airbag
If the airbag has been closed by BYD ● The indicator does not goes off The SRS airbag system is designed to
service station, the indicator still work after 5 seconds the ignition key is activate in response to a severe frontal
as above but the airbag does not have turned on or comes on again after impact or other special impact.
the protection function. it goes off. The SRS airbag is not designed to inflate if
This warning light system monitors the airbag ● The indicator comes on again the vehicle is involved in a low-speed frontal
ECU, crash sensor, inflators, warning light, when the ignition key is turned collision, side or rear collision, or if it is
interconnecting wiring, and power sources. off. involved in a rollover. But seat belts will
For details, see “Maintaining the remainder ● The indicator goes on or flashes protect occupants.
indicator and warning buzzers” in Section when driving. When impact occurs, the SRS ECU will
- 50 -
F3/F3R OWNER’S MANUAL
on most road conditions and wrong usage of This way can reduce the injury to the person
the vehicle. However, please observe this farther. After the accident, the gas in the bag
manual to drive your vehicle to ensure your will be exhausted completely. Therefore, it
safety because man reasons may lead to will not block the front visual field.
accidents. The airbag deploys at some ms, thus
carrying out extra protection towards drivers
The protected process of the airbag and passengers.
While the airbag system is activated, the gas While the airbag is deploying, there is a large
is emitted in the airbag, and the airbag sound. Generally, it does not cause the injury.
inflates quickly. The driver and passenger are Maybe it can cause the tinnitus and cause
protected by the airbag from being hurt upon you to lose hearing temporarily. However,
the head, neck and the chest when he/she these are the unabiding and you will recover
gets into the airbag while the moving inertia is quickly. The gas from the airbag may give
buffered. some smell and affect your appetite, but it
When the airbag hustles the body, it can does not cause the driver or passengers toxic.
absorb the energy, and make the gas While the airbag is inflating, it may emit some
exhaust from the bag at some speed ratio. smoke. It is normal.
- 51 -
F3/F3R OWNER’S MANUAL
Conditions when the SRS airbag does not
deploy
- 52 -
F3/F3R OWNER’S MANUAL
- 53 -
F3/F3R OWNER’S MANUAL
Please keep 25 cm between driver’s ● Children are not allowed to sit at the ● There shouldn’t be any person,
chest and steering wheel. In this way front seat without child restraint. animal or object between the SRS
the SRS airbag system will protect Since the front airbag inflates with airbag and the driver or the
driver best. It also means that front considerable speed and force, the passengers at the front seat. Do not
seats and head-rest should be child may be seriously injured or hold a child on your lap or in your
adjusted in accord with each killed. arms. It would be extremely
passenger’s figure. Besides, the ● There shouldn’t be any person, dangerous for children.
driver should keep elbow bended animal or object between the SRS ● Do not put any objects or your pets
slightly even close to straight. airbag and the driver or the on or in front of the dashboard or
● Do not affix anything onto the cover steering wheel pad that houses the
passengers at the front seat. Do not
of steering wheel or the surface of front airbag system, or the possibility
hold a child on your lap or in your
front passenger airbag position. that you get hurt will be increased in
arms. It would be extremely
Those two places must be cleaned case of accidents that
dangerous for children.
with dry dishcloth. Do not knock would activate the SRS airbag.
those places seriously. ● Do not change any part of SRS airbag
system, including marks.
- 54 -
F3/F3R OWNER’S MANUAL
● Any operation to the SRS airbag ● While you transfer your vehicle to ● The SRS airbag system has excellent
system or repair relating to this
other person, give the on-vehicle files anti-magnetic ability. However, to
system must be operated by BYD
AUTO service station. to the new owner. If the SRS airbag avoid the suddenness,do not drive the
● Change the SRS airbag system in 15 system is closed, give this file to the vehicle in some area where the
years since the manufacture date new owner, too. magnetic intensity is beyond the state
marked on the auto certificate and
● To dispose the parts of the SRS rule.
maintenance manual. This must be
operated by BYD AUTO service airbag system, observe the safety ● The SRS airbag system is fitting for
station. For replacing some parts of order and disposal process. BYD many road conditions and wrong
the SRS airbag system, please make
service station is familiar with these operation to the vehicle. But to avoid
a record.
regulations and detailed disposal the suddenness, please do not make
● The SRS airbag system only descriptions are available on the serious crash to the chassis, or do not
provides one time protection. After
maintenance manual. drive the vehicle gruffly in rough road
deployed or damaged, it must be
replaced for a new one. conditions.
- 55 -
F3/F3R OWNER’S MANUAL
Closing SRS airbag system please mark at a right position and record on SRS airbag system and suggest them to
At some situations, SRS airbag system the service manual. read this manual thoroughly.
can be closed. For examples: ● While the airbag is deploying, avoid
CAUTION
Even if the seat is adjusted correctly, contacting the airbag module. Otherwise,
In some situations, the SRS airbag
but the distance of 25 cm between the it may cause the scald or discomfort.
system can be closed. To do so,
driver’s chest and steering wheel can Contact your BYD AUTO service station
contact your BYD AUTO service
not be kept. station. Otherwise, it may cause to replace with a new SRS airbag as
Special equipment at area of steering serious injury or death. soon as possible if it has been activated
wheel for handicapped is needed to be To resume the protection function of before.
installed. the SRS airbag system, please re-start ● The SRS airbag system will be activated
The front passenger seat is adjusted your closed SRS airbag system as
only upon some
soon as possible.
due to some reason. However, the situations. Therefore, if the SRS airbag
position set upon delivery can not be Other situations system fails to work, it may not be the
guaranteed. ● Please read this manual carefully. If you problem of the system itself. Abnormal
Please contact your BYD AUTO service want to sell or dispose the vehicle, repair or untimely repair towards the
station to close the SRS please tell the new owner or the damaged parts of the vehicle may affect
airbag system. When closing an airbag, disposal factory that this vehicle has the the SRS airbag system.
- 56 -
F3/F3R OWNER’S MANUAL
Steering wheel CAUTION
Contact BYD AUTO service station upon downward to make sure that it is
the following conditions: To change the steering wheel angle, hold the locked in position.
● The SRS airbags have inflated. steering wheel, push down the lock release
● The front of the vehicle (shaded in the lever, tilt the steering wheel to the desired Audio-control switch of Steering wheel
illustration) was involved in an accident angle and return the lever to its original (option)
that was not severe enough to cause the position. Under the radio mode, press the “ ” key and
SRS airbags to inflate.
“ ” key on the main switch of steering wheel
● The pad section of the steering wheel
to search programs. Press “MUTE” to mute the
(shaded in the illustration) is scratched,
cracked, or damaged. device.
- 57 -
F3/F3R OWNER’S MANUAL
Power outer rear view mirror (Option) vehicle and thus an accident may mirror, push the switch in the
Power rear view mirror control(Option) Mirrors can be adjusted when the key is in
the “ACC” or “ON” position.
- 58 -
F3/F3R OWNER’S MANUAL
Interior rear view mirror illustration) to reduce glare from the headlight The mirror has a direction display
of the vehicle behind you during night driving. function (Option):
Start condition: The ignition switch is turned
to the ACC/ON position.
- 59 -
F3/F3R OWNER’S MANUAL
SECTION 1-4
OPERATION OF INSTRUMENTS AND CONTROLS
- 60 -
F3/F3R OWNER’S MANUAL
Headlights and turn signal light (without the position lights are on.
automatic light control system) Position 2: headlights and all lights said
above.
not running.
The indicator light (green lights) for position
lights on the instrument panel indicate that
- 61 -
F3/F3R OWNER’S MANUAL
Flashing the high beam of headlights Turn signal lights Headlights and turn signal lights (with
(position 1) To signal a turn, push the left automatic light control system---optional)
Pull the lever all the way back. The flashing multi-function switch up or down to
high beam of headlights will turn off when you position 1.
release the lever. The key must be in the “ON” position.
The headlight high beam indicator light (blue The lever automatically returns after you
light) on the instrument panel will tell you that make a turn. But you may have to return it by
the high beams are flashing. hand after you change a lane.
You can flash the high beam headlights with
the knob turned to “off”. To signal a lane change, move the lever up or
down to the pressure point (position 2) and
Headlights
hold it.
To turn on the following lights, turn the
If the turn signal indicator lights (green lights)
light adjusting switch: Position 1: position
on the instrument panel flash faster than
lights, license plate and instrument panel
normal, it means that a front or rear turn
lights.
signal bulb is burned out.
The indicator light (green light) for position
- 62 -
F3/F3R OWNER’S MANUAL
lights on the instrument turn the ignition key to “ACC” or “ON”. If your
panel will tell you that the tail light are on. vehicle will be parked for no less than one
week, make sure the headlight switch is off.
- 63 -
F3/F3R OWNER’S MANUAL
Pull the lever all the way back. The flashing The key must be in the “ON” position.
high beam of headlights will turn off when you The lever automatically returns after you
release the lever. make a turn, but you may have to return it by
You can flash the high beam headlights with hand after you change a lane.
the knob turned to “off”. To signal a lane change, move the lever up or
down to the pressure point (position 2) and
Turn signal lights hold it.
If the turn signal indicator lights (green lights)
High-low beams: For high beams, push the on the instrument panel flash faster than
lever to position 1. For low beams, push the normal, it means that a front or rear turn
lever to position 2. Pull the lever to position 3 signal bulb is burned out.
for high beams. The indicator light (blue light) High mounted braking light (optional)
for on the instrument panel the headlight high While pedaling, this light will be on together
beam will tell you that the high beams are on. with rear brake light to warn that the vehicle is
in the braking condition so that contingency
Flashing the high beam of headlights To signal a turn, push the left multi-function can be prevented.
(position 3) switch up or down to position 1. Emergency flashers
- 64 -
F3/F3R OWNER’S MANUAL
the emergency flashers are operating. Front fog lights (option)
NOTICE
- 65 -
F3/F3R OWNER’S MANUAL
While the headlights switch and rear fog Rear interior light
Rear fog lights lights switch are turned on, the
rear fog lights will be on.
While the rear fog lights switch is turned on,
the rear fog lights indicator light on the
instrument panel will be on.
While the headlights switch or the position
lights switch and front fog lights switch is
turned off, the rear fog lights will be not on
even you re-open the rear fog lights switch, To turn on the interior light, slide the
To turn on rear fog lights, press this While all of the other lights are off, the rear switch.
switch. Rear fog lights will be on upon fog lights will be off automatically. To turn on The rear interior light switch has the
following conditions: the rear fog lights, press the rear fog lights following positions:
While the position lights switch, the front fog switch again. “ON”: to keep the light on all the time.
lights, as well as the switch of the rear fog “OFF”: to turn the light off.
lights are turned on, the rear fog lights will be “DOOR”: to turn the light on when any one
on. side door or back door is
- 66 -
F3/F3R OWNER’S MANUAL
opened. The light goes off when all the side When all the side doors and back door are ignition switch light comes on when any
doors and back door are closed. unlocked using the wireless remote control, of the side doors or the back door is
the light will illuminate and remain on for opened.
Illuminated entry system about 30 seconds before fading out. ● While all the side doors and back door
When the switch is at the “DOOR” position, This function can be activated or deactivated. are closed, the light will illuminate and
the light will illuminate upon opening any one For details, see “Settings of optional remain on for about 30 seconds before
fading out.
door. After all the side doors and back door functions” in Section 1-2.
● When all the side doors and back door
are closed, the light remains on for about 30 Ignition switch indicator light(Option)
are locked using wireless remote control,
seconds before fading out.
or after all the side doors and back door
However, the light goes out immediately in
are closed, turn the ignition switch to the
the following cases. “ON” position, and the light fades.
● All the side doors and back door are ● When the all side doors and back doors
closed when the ignition key is in the are opened with wireless remote control,
“ON” position. the light will be on and remain on for
● All the side doors and back door are about 30 seconds even if the doors are
not opened.
closed and locked by the
This function can be activated or deactivated.
wireless remote control. For easy access to the ignition switch, the
For details, see “Settings of optional
functions” in Section 1-2.
- 67 -
F3/F3R OWNER’S MANUAL
To turn on the windshield wipers, move
Front interior light(with power sunroof) To turn on the front interior light,
the lever to the desired set position.
press the switch. To turn it off, press
the switch again. The ignition switch must be at the “ON”
Windshield wipers and washer To make a wipe only one time, lift the lever up
Front interior light(with power sunroof)
and release it.
- 68 -
F3/F3R OWNER’S MANUAL
To squirt washer fluid, lift the lever up. Rear window defogger(Option) With automatic air conditioning controls
After the washer squirts, release the lever. To defog or defrost the rear window, push
The wiper will operate a couple of times. the switch.
NOTICE
Do not operate the wipers if the With automatic air conditioning controls, the
windshield is dry. It may scratch defogger goes off automatically after 15 min.
- 69 -
F3/F3R OWNER’S MANUAL
discharged if the defogger operate for long Speed HUD (Head Up Display) (option) Starting conditions:
time, especially when the car stays in If the speed HUD is started, the vehicle The ignition switch is at “ON” position.
stop-and-go traffic. The defogger is not speed will be projected on the windshield. The power switch is pressed down.
designed for drying raindrop or melting snow. Thus, the driver can read the information of The vehicle is moving.
speed while paying attention to the situation Main technical specifications
of road. Item Parameter Unit
NOTICE In this way, the driving safety can be Working
DC: +9~+15 V
● With manual air conditioning improved. Voltage
controls: to prevent the battery from
Working
being discharged, turn the switch -30~70 °C
Temperature
off when the engine is not running.
Storage
● When cleaning the inside of the rear -40~80 °C
Temperature
window, be careful not to scratch or
Measuring
damage the heating wires or 0~199 km/h
Range
connectors.
Measuring
+5%
Error
Dimension 80*54*46 mm
- 70 -
F3/F3R OWNER’S MANUAL
SECTION 1-5
OPERATION OF INSTRUMENTS AND CONTROLS
- 71 -
F3/F3R OWNER’S MANUAL
Fuel gauge Engine coolant temperature gauge
accelerating or making turns. This is
caused by the fuel moving in the tank.
- 72 -
F3/F3R OWNER’S MANUAL
Tachometer
overheats, park your vehicle and allow the
NOTICE
engine to cool.
● Do not remove the thermostat on the
engine cooling system as this may
Your vehicle may overheat during severe
cause the engine to overheat. The
operating condition, such as:
thermostat is designed to control the
● Driving up a long hill on a hot day.
flow of coolant to keep the
● Idling for a long period with the air
temperature of the engine within the
conditioning on in stop-and-go traffic.
specified operating range.
● Daggling other vehicles.
● Do not continue driving with an The tachometer indicates the engine
When the ignition switch is in “START”
overheated engine. See “If your speed in thousands of rpm (revolutions
position, there is no malfunction even if the
vehicle overheats” in section 4. per minute). Use it while driving to select
engine coolant temperature gauge needle
correct shift points and to prevent engine
returns to “C”.
lugging and over-running.
Driving when the engine is running too fast
may cause excessive engine loss and poor
fuel economy.
- 73 -
F3/F3R OWNER’S MANUAL
Remember. In most cases, the slower the This meter displays the following information:
engine speed is, the fewer the fuel 1. Odometer — shows the total distance
is consumed. the vehicle has been driven.
When the ignition switch is in “START”
2. Two trip meters — shows two different
position, there is no malfunction even if the
engine coolant temperature gauge needle distances independently driven since
returns to “0”. the last time each trip meter was set to
zero.
NOTICE
You can use one trip meter (TRIP A) to
Do not let the indicator needle get
calculate the fuel consumption and the
into the red zone. This may cause
other (TRIP B) to measure the distance
severe engine damage.
on each trip.
3. Trip meter reset knob — resets the two
trip meters to zero, and also change the
meter display.
Odometer and two trip meters
To change the meter display,
quickly push and release the knob. The
meter displays changes in the order
- 74 -
F3/F3R OWNER’S MANUAL
from the odometer to trip meter (TRIP A),
then to trip meter (TRIP B), then back to
the odometer upon every pressing.
To reset the trip meter A to zero, display
the meter (TRIP A/ TRIP B) reading;
then, push and hold the knob until the
meter is set to zero.
- 75 -
F3/F3R OWNER’S MANUAL
Service reminder indicators and warning buzzers
If you are not using the parking brake, park immediately and contact your BYD AUTO
(a)
service station
- 76 -
F3/F3R OWNER’S MANUAL
(h) Turn off all the side door and back door
- 77 -
F3/F3R OWNER’S MANUAL
(a) Brake system warning light A warning light turning on briefly during In this case, not only the
operation does not indicate a problem.
This light comes on in the following cases ABS will fail but also the vehicle will
when the ignition key is at the “ON” position. CAUTION become extremely unstable during
● The brake fluid level is low. occurs, immediately park your vehicle at a
- 78 -
F3/F3R OWNER’S MANUAL
discharged. after a hard stop. There is no cause for (f) Low fuel level warning light
If it comes on while you are driving, there is a concern if it then goes out when the engine is When the fuel is nearly empty, the
problem somewhere in the charging system. accelerated slightly. light will be on. Please fill the fuel at once.
The engine ignition will continue to operate The warning light will be on if the level of oil is When driving on the slope or taking a turning,
until the battery is discharged, however. Turn low as well. This light the light would usually be on
off the air conditioning, blower, radio, etc., isn’t designed to indicate the low oil level. The earlier because the fuel in tank will swash.
and drive directly to the nearest BYD AUTO oil level must be inspected by oil dip rod.
service station. (g) “ABS” warning light
(d) Low engine oil pressure warning light NOTICE The light comes on when the ignition switch is
This light warns that the engine oil pressure is Do not drive the vehicle with the turned to the “ON” position. If there is no
too low. warning light on — even for one block. malfunction about the ABS, the light will be
If it flickers or stays on while you are driving, It may ruin the engine. off in few seconds. Then, the light would be
pull over to a safe place and stop the engine (e) Malfunction indicator light on again caused by any malfunction of the
immediately. Call a BYD AUTO service This light comes on when the electronic system.
station for assistance. injection system of the engine fails to work. When the “ABS” warning light is on (and the
The light may occasionally flicker when the If it comes on, contact your BYD AUTO brake system warning light is off), the
- 79 -
F3/F3R OWNER’S MANUAL
anti-lock brake system does solid on when the (h) Open door warning light
not operate, but the brake system still ignition key is turned to the This light remains on until all the side door
operates conventionally. “ON” position. and back door are completely closed.
When the “ABS” warning light is on (and the ● The light comes on while you are
brake system warning light is driving. (i) SRS warning light
off), the wheels could lock up during a A warning light turning on briefly during This light will illuminate when the ignition key
sudden brake or brake on slippery road operation does not indicate a problem. is turned to the “ON” position. After about 5
surfaces because the anti-lock brake system seconds, the light will go off. This means that
If either of the following conditions occurs, If the “ABS” warning light remains on properly.
this indicates that a malfunction somewhere together with the brake system warning The warning light system monitors the SRS
in the components is monitored by the light, immediately park your vehicle at a airbag system ECU, front seat belt
warning light system. Contact your BYD safe place and contact your BYD AUTO pretensioner assemblies, inflators, warning
AUTO service station as soon as possible to service station. light, interconnecting wiring, and power
check the vehicle. In this case, not only the ABS will fail
but also the vehicle will become
● The light does not illuminate or become extremely unstable during braking.
- 80 -
F3/F3R OWNER’S MANUAL
sources. ignition key in the “ACC” or “LOCK” position. start the engine.
The occurrence of either of the following All the service reminder indicators except the
condition indicates that a malfunction (k) Light reminder buzzer open door warning light should illuminate.
somewhere in the parts is monitored by the This buzzer will sound if the position lights in The “ABS”
warning light system. Contact your BYD still on and the driver’s door warning light goes off in few seconds. The
AUTO service station as soon as possible to is opened with the key removed from the SRS waning light goes off after 6 seconds.
check the vehicle. ignition switch. If any service reminder indicator or warning
buzzer does not function as described above,
● The light does not illuminate or remains have it checked by your BYD AUTO service
on for long time when the ignition key is Checking service reminder indicators station as soon as possible
turned to the “ON” position. 1. Apply the parking brake. NOTICE
● The light comes on or flashes while 2. Open one of the side door or back door. If warning light (such as discharging,
driving. The open door warning light will brake, oil, water temperature, etc.) is on
illuminate. while driving, park the car as soon as
(j) Key reminder buzzer 3. Close the door. possible and check it according to the
This buzzer reminds you to remove the key The open door warning light will go off. instructions in this manual. Contact
when you open the driver’s door with the 4. Turn the ignition key to “ON”, but do not BYD AUTO service station if necessary.
- 81 -
F3/F3R OWNER’S MANUAL
SECTION 1-6
OPERATION OF INSTRUMENTS AND CONTROLS
- 82 -
F3/F3R OWNER’S MANUAL
Ignition switch with steering lock indicate the steering wheel
malfunctions. The key can be removed only at this position.
You must press in the key to turn it from
“ON” — to switch on the engine and all “ACC” to the “LOCK” position.
accessories When starting the engine, the key may seem
This is the normal driving position. When the stuck at the “LOCK” position. To free it, first
ignition switch is turned to “ON”, the make sure that the key is pressed all the way
speedometer needle may have a move, this in, and then rock the steering wheel slightly
does not indicates malfunctions. while turning the key gently.
“START” — to start the engine
The key returns to the “ON” position when “ACC” — to enable accessories such as the
released. radio to work while stop the engine
For starting methods, see Section 3. If you leave the key in the “ACC” or “LOCK”, a NOTICE
When the ignition switch is turned to the buzzer will remind you to remove the key Do not leave the key in the “ON”
“START” position, the tachometer, fuel gauge, when opening the driver’s door. position if the engine is not running.
and engine coolant temperature gauge The battery will discharge and the
needles will return to bottom. This does not “LOCK” — to switch off the engine and lock ignition device could be damaged.
- 83 -
F3/F3R OWNER’S MANUAL
Parking brake
To set: pull up the lever. For better holding
power, first depress the brake pedal and hold
CAUTION
it while setting the parking brake.
Before driving, be sure the parking
To release:
brake is fully released and the parking
(1) Pull up the lever slightly.
brake reminder light is off.
(2) Press the lock release button.
(3) Loosen the lever.
To remind you that the parking brake
is set, the parking brake reminder light in the
instrument panel remains on until you release
When parking, firmly apply the parking the parking brake.
brake to avoid inadvertent creeping.
- 84 -
F3/F3R OWNER’S MANUAL
SECTION 1-7
OPERATION OF INSTRUMENTS AND CONTROLS
CNG system
Introduction for CNG vehicle fuel supply system structure………………………………………………………………………………. 8 6
- 85 -
F3/F3R OWNER’S MANUAL
Introduction for CNG vehicle fuel supply system structure
CNG vehicle adds the multi-point natural gas injection system compared with F3 fuel supply system.
Multi-point natural gas injection system is mainly made up of gas storage system, supply system and control system:
Gas storage system :is mainly made up of gas inlet, gas inlet 3-way,CNG bottle, CNG bottle valve, high pressure pipeline, connector, etc.
Supply system :is mainly made up of redactor, low pressure pipeline, high frequency solenoid valve group, molding pipe, etc.
Control system:is mainly made up of gas controller assembly, ignition time regulator, conversion switch, etc.
Specification for CNG vehicle fuel conversion operation
Conversion switches of multi-point natural gas injection system.
- 86 -
F3/F3R OWNER’S MANUAL
Natural gas gauge indicator is made up of 4 green light and one red li
-ght. Every green light indicates about 1/4 capacity; red light indicates
the gas is not enough.
- 87 -
F3/F3R OWNER’S MANUAL
(1)Starting CNG vehicle
To protect the reductor and make sure that gasoline system is under normal state The vehicle is using gasoline to start regardness of the
position of conversion switch.If the gasoline system appears malfunction, engine can not use gasoline to work, to make the engine using
natural gas to work on, so the natural system sets the function of using natural gas to start directly.
a. Using natural gas to start
Shift the fuel conversion switch to “G” position, then check whether the gas gauge switch is indicating. Shift ignition key to “ON” gear, controller is
starting, at the moment gasoline working indicator is lighting, while natural gas working indicator is twinkling; shift conversion switch from “G”
position to gasoline position, then return to “G” position, at the moment natural gas and gasoline working indicator light are both lighting; then start
the engine, engine is using natural gas to start and work.
- 88 -
F3/F3R OWNER’S MANUAL
Caution
In normal situation, suggest using gasoline to start, do not use natural gas to start. While, if the engine water temperature is over 60℃,
please use natural gas to start directly, otherwise redactor will be damaged.
b. Using gasoline to start
Shift conversion switch to gasoline position, start as the natural driving operation procedure.
(2)Fuel conversion
a. From natural gas to gasoline
Shift the fuel conversion switch from “G” position to gasoline position, at the moment natural gas solenoid valve is close, fuel pump relay is close,
and fuel pump is working. Engine uses gasoline to work.
b. From gasoline to natural gas
Shift fuel conversion switch from gasoline position to “G” position, at the moment engine is using gasoline to work, gasoline indicator is lighting.
Step down accelerator pedal, loosen accelerator pedal until engine speed is above 2000rmp. When engine speed is under 2000rpm, system
transforms to natural gas working model, at the same time natural gas indicator is lighting, gasoline indicator is going out.
Caution
When fuel conversion, there will be a fuel supply transition period, at the moment the engine may be low down speed or gently idle. To
avoid engine stopping working, carry through fuel conversion when high engine speed, and do not carry through fuel conversion at the
place of traffic jam, upgrade and downgrade, swerve or bad line of sight.
- 89 -
F3/F3R OWNER’S MANUAL
SECTION 1-8
OPERATION OF INSTRUMENTS AND CONTROLS
- 90 -
F3/F3R OWNER’S MANUAL
Instruction of on-board CD player (Option)
Function and feature
1. CD supported
2. Built in AM/FM radio
3. Anti-vibration structure
4. MAX. power output: 25 W*4
5. Audio input supported
Specifications:
- 91 -
F3/F3R OWNER’S MANUAL
Instruction of the on-board CD function panel
- 92 -
F3/F3R OWNER’S MANUAL
- 93 -
F3/F3R OWNER’S MANUAL
Co nne ct one end of the aud io line to the external audio de vice, such as the MP3 outpu t and the other en d to the
AU X input. Switch on your CD pla yer and press this button, thus you can pla y the tra cks stored in your external
au dio device via the on- boa rd CD player if the devi ce is tur ned on.
In other play m odes, you can press the AUX button to enab le the exter nal au dio device to play. If no ex ternal
au dio device is avai lab le, you will retu rn to the prev ious play mode.
Aft er your CD player is turn ed on , the external aud io de vice play m ode will be ac cessed direc tly if it is inser ted .
“ ∧ ” and “ ∨ ”:
Rad io mo de: Press the bu tton for 0.5 se con d to selec t a ch ann el bac kward or fo rward and for 2 seconds abo ve
to search the previ ous or next avai lab le ch an nel automati cally.
CD mo de : Press the bu tton to selec t a track bac kward or fo rward. Pr ess and hold it to perform fast fo rward or
fast re wind.
To resume norm al play, rel ease it.
2
RPT
- 94 -
F3/F3R OWNER’S MANUAL
3
INT
4
RDN
NOTICE: CD: CD disk is playing; Radio: The radio is in signal receiving state.
- 95 -
F3/F3R OWNER’S MANUAL
- 96 -
F3/F3R OWNER’S MANUAL
- 97 -
F3/F3R OWNER’S MANUAL
Instruction of the multi-media player function panel
Instruction of multi-media player function panel keys Power-Volume adjusting knob: To adjust the
- 98 -
F3/F3R OWNER’S MANUAL
volume/audio mode. To adjust the volume, “MUTE” key: Press the key to mute your above to search the next channel
turn the knob. To switch the audio mode device. To resume, press it again. automatically. In CD play mode, press the
among VOL, BAS, TRE, BAL, and FRD in key to operate single-direction
“AM/FM” key: To choose radio wave band at
turn, press the knob. To change a mode, turn music-choosing. Press it for a while to
the sequence of “FM1”, “FM2”, “FM3”, “AM1”,
the knob leftward or rightward. perform FF or REW. To return to normal state,
and “AM2”.
release the key.
Switch/manual frequency modulation knob:
“SCM”key: Preset the equalizer. “BEAT”
To switch on the device or search a channel “ ” key: Press it to play a CD or pause.
indicates strong sound effect applying to rock
manually. In the radio mode, press it to Press it once to pause and again to continue
& roll and disco waltz; “SOFT” indicates soft
operate single-step channel-choosing. playing.
sound
“SRC” key: To choose play mode or radio
mode. To switch the mode,
effect applying to quiet music; “POP” “SHF” key: Press it to play randomly. Press
press the key. To resume, press it again. indicates popular effect, applying to popular it again to cancel it.
music.
“GPS” key: Press it to switch the current “RPT” key: Press it to activate the repeated
mode to “GPS” display mode. To resume, “ ”/“ ”: In radio mode, press the key play mode. To quit, press it again.
press the key again. for 0.5 second to perform single-step
channel-choosing. Press it for 2 seconds or
- 99 -
F3/F3R OWNER’S MANUAL
“MBP” key: To choose a suitable position for “TILT” key: Press it to adjust the vision angle
listening. Basing on your position, choose the of liquid crystal display. The display can be
perfect timbre, moved by 10º, 20º and 30º.
- 100 -
F3/F3R OWNER’S MANUAL
Troubleshooting for multimedia player
Failure Reason Solution
1. Turn the vehicle key to “ACC” or
1. The ignition switch is not turned on. “ON”.
1 No power or sound 2. The wire is not connected properly. 2. Check the wire connection.
3. The fuse breaks. 3. Change a fuse with specified
specification.
1. The disk is put in reversely.
1. Put in the disk correctly.
2 No sound with disk put in 2. The disk is dirty or scratched
2. Wipe the disk or change a new one
seriously.
1. Fix the machine with installation
1. Installation is infirm.
parts.
3 Unstable sound caused by vibration 2. The disk is dirty or scratched
2. Clean up the disk or change a new
seriously.
one.
Can not store channels and the preset
4 The battery line is connected improperly. Connect the cable to correct pole.
broadcast
The noise sent by FM stereophony and The broadcasting station is far away or the Choose other broadcasting station with
5
single channel broadcast give are too loud signal is excessively weak. stronger signal.
- 101 -
F3/F3R OWNER’S MANUAL
- 102 -
F3/F3R OWNER’S MANUAL
/distance needed to drive or driven. and national map. The national map highly precision. When the vehicle drives into
2. Course Deviation Indicator lists all towns, traffic artery, and rivers. an area without satellite data (e.g. tunnel,
When users drive the wrong route or sheer The particular maps even show roads between high buildings), a gyroscope,
from the marked-out route with traffic jam or constructions and small alleys in range and a speed sensor can be applied to
restraint, the system will reprogram the route of 50 meters calculate the current position for automatic
so that users can arrive as soon as possible. The touch screen facilitates zooming navigation.
3. Integrative information inquiry in/out and roaming operation.
Inquire the position by unit name. Display the vehicle position at any time. NOTICE
Inquire the companies or The map is designed with SD memory Do not use CDs with viscous labels
institutions near to one certain position. card, which eases the renewal of map which may scroll. This may cause
4. Zoom in/zoom out of the map and roaming the CD to get stuck in the player.
data.
Abundant electronic map information, 5. Satellite navigation together with automatic
including particular maps of 34 navigation
capital-level cities all over the country The system can provide satellite navigation of
- 103 -
F3/F3R OWNER’S MANUAL
SECTION 1-8
OPERATION OF INSTRUMENTS AND
CONTROLS
- 104 -
F3/F3R OWNER’S MANUAL
- 105 -
F3/F3R OWNER’S MANUAL
Fan speed selector Use when the air cycle mode knob stays in
Turn the knob to adjust the fan speed: To FRESH.
increase, turn the knob clockwise. To 5 WINDSHIELD: The air flows mainly from
decrease, turn the knob anticlockwise. At the the windshield vents.
same time, there will be leaf-like icons Use when the air cycle mode knob stays in
showed on the controls (if an anion generator Air flow mode selector FRESH.
is equipped) Turn the knob to select the vent used for For instructions on settings of air flow knob,
Cool/warm wind selector air flow. see the following part.
Turn the knob to adjust the temperature: To 1 PANAL: The air flows mainly from the Air cycle mode selector
select warm wind, turn the knob clockwise. instrument panel vents and side vents.
To select cool wind, turn the knob 2 BI-LEVEL: The air flows from the floor
anticlockwise. To turn off the air conditioning, vents, the instrument panel vents and side
turn the knob to “OFF”. vents.
3 FLOOR: The air flows mainly from the floor
vents.
4 FLOOR/WINDSHIELD: The air Move the lever to select the air source.
flows mainly from the floor vents and 1. RECIRCULATE: To re-circulate the air
windshield vents. inside the vehicle.
- 106 -
F3/F3R OWNER’S MANUAL
2. FRESH: To draw the external air into the speed for one minute to help clear the
system. intake ducts of snow or moisture. This can
reduce the amount of fogging in the
“A/C” BUTTON windows.
To turn the air condition on, first turn the fan When driving on dusty roads, close all
speed knob, and then press the “A/C” button. windows. If dust thrown up by the vehicle is
The “A/C” button indicator will illuminate. To Make sure the air intake grilles in front of still drawn into the vehicle after closing the
turn the air conditioning off, press the button the windshield are not blocked (by leaves windows, it is recommended that the air
again or set the fan speed knob to “0”. or snow, for example). intake selector be set to FRESH and the
Air flow knob settings On humid days, do not blow cold air on fan speed selector to any position expect
the windshield. The windshield could fog “0”.
Operating tips
up because of the difference in air
To cool off your BYD F3 after it has been
temperature on the inside and outside of
parked in the hot sun, drive with the
the windshield.
windows open for a few minutes.
Keep the underside of front seats vacant
so that air in vehicle can be cycled
completely.
On cold days, set the fan speed to high
- 107 -
F3/F3R OWNER’S MANUAL
- 108 -
F3/F3R OWNER’S MANUAL
Defrosting
The outside of the windshield
For best results, set controls to:
- 109 -
F3/F3R OWNER’S MANUAL
Automatic air condition system (Option)
Control panel
1. Fan speed selector
2. “OUTSIDE TEMP” button
3. “TEMP” button
4. “AUTO” button
5. “OFF” button
6. Air intake selector
7. Air flow selector
8. Front defroster button
9. “A/C” button
- 110 -
F3/F3R OWNER’S MANUAL
“AUTO” button “TEMP” button Air flow selector
For automatic operation of the air conditioner, To increase the temperature, press the “∧”
press the “AUTO” button. An indicator light side. To decrease it, press the “∨” side.
will illuminate to show that the automatic “MAX. COLD” appears when you adjust to
operation mode has been selected. maximum cooling temperature, and “MAX.
In the automatic operation mode, the air
HOT” appears when you adjust to maximum
conditioner selects the most suitable fan
warming temperature.
speed and air flow according to the
The anion generator will work while fan
temperature.
You may use manual controls if you want to working.
select your own settings. “OURSIDE TEMP” button
To turn off the automatic operation, press Press the “OURSIDE TEMP” button to
“OFF” button, the air flow selector, or fan change the temperature display between the
Turn the knob to select the vent used for
speed selector. air conditioning temperature and outside
air flow.
Fan speed selector temperature. For details, see “Outside
In the automatic operation mode, there is not
Push the “∧” (increase) or “∨” (decrease) temperature display” in section 1-9.
button to adjust the fan speed. necessary to adjust the air flow unless need
In automatic operation, you do not have to other way of air flow.
adjust the fan speed unless you want to use 1 PANAL: The air flows mainly from the
another fan speed mode. instrument panel vents and side vents.
“OFF” button
2 BI-LEVEL: The air flows from the floor
Press the button to turn off the air
vents, the instrument panel vents and side
conditioning system.
vents.
3 FLOOR: The air flows mainly from the floor
- 111 -
F3/F3R OWNER’S MANUAL
parked in the hot sun, drive with the windshield. The windshield could fog up
windows open for a few minutes. This because of the difference in air
On cold days, set the fan speed to high temperature on the inside and outside of
conditioning to cool the interior more intake ducts of snow or moisture. This
seats clear to allow air to circulate Make sure the air intake grilles in front of
throughout the vehicle. the windshield are not blocked (by leaves
or snow, for example).
- 113 -
F3/F3R OWNER’S MANUAL
When driving on dusty roads, close all Fan speed: to the desired fan speed Press in the “AUTO” button
windows. If dust thrown up by the vehicle Temperature: towards high temperature Temperature: to the desired temperature
is still drawn into the vehicle after closing Air intake: FRESH (outside air) Air intake: FRESH (outside air)
Air flow: FLOOR
the windows, it is recommended that the
Air conditioning: OFF For manual operation
air intake selector be set to FRESH and
the fan speed selector to any value. For quick heating, select re-circulated air Fan speed: to the desired fan speed
Temperature: towards low temperature
for a few minutes. To keep the windows
Air intake: FRESH (outside air)
from fogging, select FRESH
Air flow: PANEL
after the vehicle interior has been warmed. Air conditioning: ON
Choose FLOOR/WINDSHIELD air For quick cooling, move the air intake
Heating selector to RECIRCULATE for a few
flow to heat the vehicle interior while
For best results, set controls to: minutes.
For automatic operation defrosting or defogging the windshield. Ventilation
For best results, set controls to:
Press in the “AUTO” button Air conditioning
Temperature: to the desired temperature For best results, set controls to: Fan speed: to the desired fan speed
Air intake: FRESH (outside air) For automatic operation Temperature: towards low temperature
Air conditioning: OFF Air intake: FRESH (outside air)
For manual operation Air flow: PANEL
Air conditioning: OFF
- 114 -
F3/F3R OWNER’S MANUAL
Side vents Checking and replacing air conditioning
filter
- 115 -
F3/F3R OWNER’S MANUAL
The air conditioning filter is placed behind 1. Open the right glove box and use a 2. Press both sides of the glove box to
the glove box. cross-head screwdriver to release the unfasten the pothook and remove the
The air condition will be blocked though a
specified screw on the damper. glove box.
long time. If you feel that the air flow
decreases, replace the air conditioning filter.
To guarantee the A/C working effect, follow
the maintain plan to check and replace the air
filter. For details, see Section 6.
- 116 -
F3/F3R OWNER’S MANUAL
CAUTION
The air conditioning filter must be
installed in its correct position. Using
an air conditioning system without a
filter will weaken the dust-proof
function and the air conditioning
- 117 -
F3/F3R OWNER’S MANUAL
Install the glove box 2. Connect the glove box, draw out the 3. Press both sides of glove box and close
1. Insert the pin into the damper hole as damper, and insert the screw into damper. it.
illustrated above. Use the cross-head screwdriver to tighten
the screw.
- 118 -
F3/F3R OWNER’S MANUAL
SECTION1-9
OPERATION OF INSTRUMENTS AND CONTROLS
9. Other equipment
Electronic clock……………………………………………………………………………………………………………...120
Outside temperature display…………………………………………………………………………………………………120
Cigarette lighter and ashtrays………………………………………………………………………………………………..120
………………………………………………………………………………………………………… ……121
Right glove box……
Auxiliary box ……………………………………………………………………………………………………………....122
Console box…………………………………………………………………………………………………………… …….122
Reverse radar system………………………………………………………………………………………………………..123
Rear sun visor………………………………………………………………………………………………………………..127
- 119 -
F3/F3R OWNER’S MANUAL
Electronic clock disconnected from the clock, the time display pushing the “OUTSIDE TEMP” button once to
will automatically be set to AM 1:00. show the outside temperature. Pushing the
Outside temperature display (For “OUTSIDE TEMP” or “TEMP” button will
automatic air condition system) change the display back to the air
conditioning temperature.
- 120 -
F3/F3R OWNER’S MANUAL
Ashtray
To use the ashtray, pull it out.
When finishing with your cigarette, thoroughly
extinguish it in the ashtray to prevent other
cigarette butts from catching fire. After using
the ashtray, close the lid completely.
Front: to remove the ashtray, press down on
Cigarette lighter and rear ashtray the lock spring plate and pull it out.
Rear: to remove the ashtray, hold the ashtray To open the glove box door, pull the lever.
Cigarette lighter on both sides and pull it out.
To use the cigarette lighter, press it in. After CAUTION
finishing heating up, it automatically pops out To reduce the chance of injury in case
ready for use. of an accident or sudden stop while
If the engine is not running, the key must be driving, always completely close the
in the “ACC” position. ashtray after use.
Do not keep the cigarette lighter being Right glove box
pressed in.
- 121 -
F3/F3R OWNER’S MANUAL
Left glove box (Auxiliary box) Console box (option)
CAUTION
To reduce the chance of injury in
case of an accident or a sudden
stop, always keep the console box
To use the box, pull on the handle. closed while driving.
- 122 -
F3/F3R OWNER’S MANUAL
Cup holder (option) Reverse radar system (option for F3)
The cup holder is designed for holding Reverse radar system Open: press the switch and the indicator
cups or drink-cans securely. While reverse, the reverse radar system illuminates and the buzzer beeps.
prompts the driver the distance between
Close: press the switch again to turn off the
vehicle and stumbling block through indicator
system.
light and buzzer. The system uses the
sensor to detect stumbling blocks.
- 123 -
F3/F3R OWNER’S MANUAL
distance
(mm)
- 124 -
F3/F3R OWNER’S MANUAL
When the ignition key stays at “ON”
A refers to
position and the selector lever is in Indicator Buzzer
distance (mm)
reverse gear, the system is under
About l,000-750 Flash Intermittently
working.
beeps
Quickly and
This system prompts driver distance between
vehicle and stumbling block through indicator About 750-500 Flash intermittently
light and buzzer.
beeps
- 125 -
F3/F3R OWNER’S MANUAL
Sensing area The system may not work normally at ● The sensor is shielded by hand.
The sensing area (i.e. the maximal distance following conditions: ● The vehicle is too near to objects.
from “A”) of the sensor reaches to about ● There is something on the sensor, for ● The sensor is knocked seriously.
1100mm. example, ice, snow, slurry and so on.
Apperceive is limited, so you have to check ● The vehicle has been parked at higher
the surroundings before starting driving and temperature and lower temperature
get vehicle started slowly. surrounding for long time.
● The vehicle is driven at muddy, rude, or
other special road.
CAUTION
● The vehicle is near the objects which
Do not affix something onto sensor.
can eradiate ultrasonic, such as vehicle If the following things come near the
Otherwise, this may cause the system
horn, motor of motorcycle and so on. sensor, the system may fails to work:
not to work normally and even an
● Drive the vehicle when it rains heavy or ● Metal lead wire, cord, or thin objects
accident.
water spatters on vehicle. ● Cotton, snowflakes or objects with
● Install the dual-pass wireless antenna or absorbency
buffer. ● Small objects
● The center of gravity is acclivitous. ● Objects with sharp ends
- 126 -
F3/F3R OWNER’S MANUAL
● High and protuberant objects
To raise the rear sun visor, pull the hook of
Please contact your BYD AUTO service the rear sun visor and hang it to the bracket.
station at following situations: To descend it, pull the hook and put it down.
● The bumpers are destroyed or sunken.
● The indicator is solid on but the buzzer NOTICE
does not beep. Follow the rules below. Otherwise,
damages or losses may be caused.
Rear sun visor (optional) ● Do not put any objects that may
block the curtain from moving under
the rear sun visor.
● Do not place objects on the visor.
- 127 -
F3/F3R OWNER’S MANUAL
Section 2 Driving Information for BYD F3
Running-in period……………………………………………………………………………………………………………129
Fuel…………………………………………………………………………………………………………………………..129
Fuel cut-off system…………………………………………………………………………………………………………..130
Three-way catalytic converter……………………………………………………………………………………………….130
Engine exhaust cautions……………………………………………………………………………………………………..131
Facts about engine oil consumption…………………………………………………………………………………………132
Shift control …………………………………………………………………………………………………………………133
Brake system…………………………………………………………………………………………………………………133
Warning of brake pad ………………………………………………………………………………………………………138
Luggage storage precautions………………………………………………………………………………………………..141
Suspension and chassis………………………………………………………………………………………………………141
- 128 -
F3/F3R OWNER’S MANUAL
Drive gently and avoid high speed. Selecting the proper fuel is essential for
- 129 -
F3/F3R OWNER’S MANUAL
Do not use leaded gasoline on vehicle. station. Before restarting the engine, check
This may cause the three-way catalytic However, it is normal to hear brief and the ground below your vehicle. If fuel
converter to lose its effectiveness and slight knock when accelerating and leaks to the ground, then the fuel
the emission control system to grabbling. Do not worry. system would be damaged and need
function improperly. In addition, this repair. In this case, do not restart the
Fuel tank capacity: 50 L
can increase the maintenance cost. engine.
The vehicle emission system must Fuel cut-off system
- 130 -
F3/F3R OWNER’S MANUAL
- 131 -
F3/F3R OWNER’S MANUAL
● Do not turn off the ignition switch required by your BYD AUTO Engine exhaust cautions
- 132 -
F3/F3R OWNER’S MANUAL
only in an unconfined area and Facts about engine oil consumption is burned by
adjust the heating or cooling system Functions of engine oil
● the high temperature combustion gases
to force outside air into the vehicle. Engine oil has the primary functions of
lubricating and cooling the inside of the during the combustion process.
● Keep the luggage component lid or
back door closed while driving. An engine, and plays a major role in maintaining ● Oil is also used to lubricate the stems
open or unsealed trunk lid or back the engine in proper working order. of the intake valves. Some of this oil is
door may cause exhaust gases to Engine oil consumption
sucked into the combustion chamber
be drawn into the vehicle. It is normal that an engine should consume
some engine oil during normal engine together with the intake air and is
● To allow proper operation of your
operation. The causes of oil consumption in a burned along with the fuel. High
vehicle’s ventilation system, keep
the inlet grilles in front of the normal engine are as follows. temperature exhaust gases also burn
windshield clear of snow, leaves, or ● Oil is used to lubricate pistons, the oil used to lubricate the exhaust
other obstructions. piston rings, and cylinders. A thin film valve stems.
● If you smell exhaust fumes in the The amount of engine oil consumed
of oil is left on the cylinder wall when a
vehicle, drive with the windows
piston moves downwards in the cylinder. depends on the viscosity of the oil, the
open and the luggage component
lid or back door closed. Have the High negative pressure generated sucks quality of the oil and the
cause immediately located and conditions the vehicle is driven under.
some of this oil into the combustion
corrected.
chamber when the More oil is consumed by high-speed driving
vehicle is decelerating. This oil as some and frequent acceleration and deceleration.
part of the oil film left on the cylinder wall A new engine consumes more oil, since its
- 133 -
F3/F3R OWNER’S MANUAL
pistons, piston rings and cylinder walls have For example, if vehicle repeatedly drives for a
not become conditioned. short distance, oil would be consumed. In this
case, even if the vehicle drives for 1,000 km
Oil consumption: or above, oil level displayed on oil dip rod
would not decrease since oil has been
Max. 1.0 L/1,000 km
rarefied by fuel and smoke.
When judging oil consumption, pay If vehicle drives at high speed (e.g. on
attention to that it would be difficult to freeway), rarefied oil would ablate, so oil will
judge the real oil level because oil be over-consumed after high speed driving.
rarefies.
- 134 -
F3/F3R OWNER’S MANUAL
Importance of engine oil level check Shift control short stay. This will stop the gear to avoid mill
One of the most important points in proper each other.
Manual transmission
vehicle maintenance is to keep the engine oil
at the optimum level so that oil function will To run smoothly, the manual transmission is Slow down, under shift can obtain additional
not be impaired. Therefore, it is essential that synchronized at all the drive gear, the manual braking force from the engine. This additional
the oil level be checked regularly. BYD AUTO transmission is equipped with locking devices braking force will help maintain a safe speed,
recommends that the oil level be checked so as not to directly shift from the 5 gear to to prevent the brakes overheating in the
every time you refuel the vehicle. reverse. You should press clutch pedal to downhill.
end when shifting, not let your foot on the
NOTICE clutch pedal, otherwise it will speed up the Warning:
Failure to check the oil level regularly clutch abrasion when no shift. Fast accelerate and fast decelerate on the
could lead to serious engine trouble slip road will cause the losing
due to insufficient oil. Shift to the Reverse only stopping the vehicle control of vehicle. The event of a crash will
completely. Shifting to cause you injury. Should be extra carefully
For detailed information on oil level check, Reverse during driving will damage the driving at the slip road.
see “Checking the engine oil transmission. After pressing on the clutch
level” in Section7-2. pedal, before shifting to reverse, should stay Automatic transmission
a few seconds, or shift the drive gear on a
- 135 -
F3/F3R OWNER’S MANUAL
The automatic transmission of BYD F3 with 4 and speedometer show which position the Press the release button on the front of the
drive gear controlled by electronic control shift lever is in. shift lever to move it.
system can shift stablely, equipped with If you have done all of the above and still
The engine warning indicator will comes on if
“lockup type” torque converter can reduce the cannot move the lever out of Park, see “Shift
the automatic transmission failure.
fuel consumption Lock Release” on page .
Shift lever position
Shift lever position indicators:
The shift lever has 7 gears, when start the
engine, the shift lever should be the P or N
gear position. When you want to stop the
vehicle with the gear at d, 3, 2, L, N or R
position, you should forcibly step the brake
pedal, and get away from the accelerator
pedal You
must also press the release button to shift
Park (P)—This position mechanically locks
into Park. To avoid transmission damage,
the transmission. Use Park whenever you are
come to a complete stop before shifting into
turning off or starting the engine. To shift out
Park. The shift lever must be in Park before
of Park, you must press on the brake pedal
These indicators between the tachometer you can remove the key from
and have your foot off the accelerator pedal.
- 136 -
F3/F3R OWNER’S MANUAL
the ignition switch. and acceleration. You may notice the
Reverse (R)—How to shift from Park to transmission shifting up at higher speeds Second (2)—To shift to Second, press the
Reverse refer to “Park”. Shift from the Neutral when the engine is cold. This helps the release button on the front of the shift lever.
engine warm up faster. This position locks the transmission in
to Reverse should after stop the vehicle
Drive (D3)—This position is similar to D,
completely and should press the release second gear, it will not shift to first gear
except only the first three gears are selected
button. automatically. At the second gear, can
instead of all five. Use D3 when towing a
Neutral (N)—Use Neutral if you need to provide more power when climbing; increase
trailer in hilly terrain, or to provide engine
restart a stalled engine, or if it is necessary to the engine braking when going down steep
braking when going down a steep hill. D can
stop briefly with the engine idling. Shift to the hills, reduce the wheel spin when starting the
also keep the transmission from cycling
Park position if you need to leave your engine on a slippery
between third and fourth gears in stop-and-go
driving. road or in deep snow.
vehicle and apply the parking brake. Press on
the brake pedal when you are moving the
When at D3 and D, press the accelerator First (L)—To shift from Second to First, press
shift lever from Neutral to another gear.
pedal down to bottom can speed up quickly, the release button on the front of the shift
then the transmission will under shift lever. This position locks the transmission in
Drive (D)—Use this position for your normal
automatically. The transmission shift to First first gear. By upshifting and downshifting
driving. The transmission automatically
or Second according to the speed of press through 1, 2, D , and D, you can operate this
selects a suitable gear for the vehicle speed
the accelerator pedal transmission much like a manual
- 137 -
F3/F3R OWNER’S MANUAL
- 138 -
F3/F3R OWNER’S MANUAL
The anti-lock brake system is designed to Effective ways to press the ABS brake pedal: You may hear a click or motor sound in the
help prevent lock-up of the wheels during when the anti-lock brake system function is engine compartment for a few seconds when
a sudden brake or brake on slippery road working, you may feel the brake pedal the engine is started or just after the vehicle
surfaces. This assists in providing pulsating and hear a noise. In this condition, begins to move. This means that the anti-lock
directional stability and steering to enable the anti-lock brake system to work, brake system is in the self-check mode, and
performance of the vehicle under these just hold the brake pedal down more firmly. does not indicate a malfunction.
circumstances. Do not pump the brake in a panic stop. This
will result in reduced braking performance. When the anti-lock brake system is
The anti-lock brake system becomes activated, the following conditions may
operative after the vehicle has accelerated to occur. They do not indicate a malfunction
a speed in excess of approximately 5 km/h. It of the system:
stops operating when the vehicle decelerates ● You may hear the anti-lock brake
to a speed below approximately 5km/h. system operating and feel the
In rainy days, it is easy to activate brake pedal pulsating and the vibrations
anti-lock brake system when stepping on of the vehicle body and steering wheel.
brake pedal on slippery surface, such as the You may also hear the motor sound in
cap of well, armor plate or the joint of bridges. the engine compartment even after the
- 139 -
F3/F3R OWNER’S MANUAL
vehicle is stopped. during high speed driving in the rain, the vehicle speeds using the speed
● At the end of the anti-lock brake system anti-lock brake system does not provide sensors for respective wheels’ turning
vehicle control. speeds. The use of tires rather than
activation, the brake pedal may move a
Anti-lock brake system is not designed to specified may fail to detect the
little forward.
shorten the stopping distance:
accurate turning speed resulting in a
Compared with vehicles without an
longer stopping distance.
anti-lock brake system, your vehicle may
CAUTION require a longer stopping distance in the
Do not overestimate the anti-lock brake following cases:
system: although the anti-lock brake ● Driving on rough, gravel, or
Disk/drum integrated parking brake
system assists in providing vehicle snow-covered roads.
Vehicle is equipped with drum parking
control, it is still important to drive with all ● Driving with wheel chains installed.
brake. This type of parking brake needs to
due care and maintain a moderate speed ● Driving over the steps such as the
joints on the road. change brake shoe or brake drum
and safe distance from the vehicle in front
● Driving on bumpy or uneven roads. periodically and have them wear in by
of you, because there are limits to the
Install all 4 tires of specified size at your BYD AUTO service station.
vehicle stability and effectiveness of
steering wheel operation even with the appropriate pressure: the anti-lock
anti-lock brake system on. brake system detects
If tire grip performance exceeds its
capability, or if hydroplaning occurs
- 140 -
F3/F3R OWNER’S MANUAL
Warning of brake pad possible. CAUTION
Do not drive your vehicle for long time when Do not modify the suspension/chassis
there is a warning sound. with lift kits, spacers, springs, etc.
Luggage storage precautions This can cause dangerous handling
When stowing cargo and luggage in the characteristics, resulting in loss of
vehicle, observe the following rules: control.
● Put cargo and luggage in the trunk or
luggage compartment when possible.
There is warning of brake pad. When the Be sure all items are secured in place.
brake pad is over-worn, there will be a ● Be careful to keep the vehicle balanced.
warning sound. Locating the weight as forward as
possible helps maintain balance.
If you hear a scream or friction noise, please ● For better fuel economy, do not carry
contact with BYD AUTO service station to unneeded weight.
replace the brake friction disc as soon as Suspension and chassis
- 141 -
F3/F3R OWNER’S MANUAL
Section 3 Starting and Driving
- 142 -
F3/F3R OWNER’S MANUAL
- 143 -
F3/F3R OWNER’S MANUAL
Engine gets heating up by running but idling. over-speed mode. Safety check
Run the engine steadily to warm up the It is a good idea to do a safety check before
If engine is hard to be started or
vehicle till the temperature of engine coolant starting out on a trip. A few minutes of
stall frequently, check the
rises to normal range. checking can help ensure safe and pleasant
engine at once.
driving. Just a basic familiarity with your
If the engine starts
vehicle is required and a careful eye!
Follow the correct procedure given in normal Otherwise, if necessary, BYD AUTO service
start to restart it. station will do the check at a low cost.
If the engine will not start
See “If your vehicle will not start” in Section 4. CAUTION
NOTICE If you make this check in an enclosed
Starting operation of engine can garage, make sure there is adequate
not excess 30 seconds, or it will ventilation. The engine exhaust is
lead to over-heat of engine and poisonous.
circuit system. Before starting the engine
- 144 -
F3/F3R OWNER’S MANUAL
Outside the vehicle Spare tire, jack, and wheel nut wrench: amperage ratings designated on the fuse box
Tire: check the pressure with a gauge and Check the tire pressure and make sure you lid.
look carefully for cuts, damage, or excessive have your jack and wheel nut wrench. Coolant level: make sure the coolant level is
wear. Seat belts: check that the buckles lock correct. See Section 7-2 for instructions.
Wheel nuts: make sure no nuts are missing securely. Make sure the belts are not worn or Battery and cables: all the battery cells
or lost. frayed. should be filled to the proper level with
Fluid leaks: after the vehicle has been Instruments and controls: special attention distilled water. Look for corroded or loose
parked for a while, check the underneath for should be taken to make sure that the service terminals and a cracked case. Check the
leaking fuel, oil water, or fluid. (Water reminder indicators, instrument lights, and cables for good condition and connections.
dripping from the air conditioning after use is defrosters are working. Wiring: look for damaged, loose, or
normal.) Brake: make sure the pedal has enough disconnected wires.
Lights: Make sure the headlights, stop lights, clearance and the brake works Fuel lines: check the lines for leaks
tail lights, turn signals and other lights are all properly. or loose connections.
working. Check In the engine compartment CAUTION
the headlight strength. Do not stack children’s toys inside the
Inside the vehicle Spare fuses: make sure you have spare vehicle. Although easy for play, this
fuses. They should cover all the may cause potential safety hazards,
- 145 -
F3/F3R OWNER’S MANUAL
especially for emergency brakes or gauges are working. severe tire damage such as a tire burst.
crashes. These toys not only affect the Brake: in a safe place, check that the brakes ● Drive slowly on the rough road.
driving safety, but also can become do not pull the one side when applied. Otherwise, the wheels or the tires may
After starting the engine If there’s no malfunction, you can get deep water may get the brakes wet. To
released and enjoy your driving. see whether they
Exhaust system: listen for any leakage. Note whether there is some noise at the are wet, check that there is no traffic
Have any leaks fixed immediately. See beginning. near you first, and then press the pedal
“engine exhaust cautions” in Section 2. lightly. If you do not feel a normal braking
Engine oil level: stop the engine and Tips for driving in various conditions force, the brakes are probably wet. To
park on a level spot. See section 7-2 ● Always slow down in gusty crosswinds. dry them, drive the vehicle cautiously
for instructions. This allows you to control much better. while lightly pressing the brake pedal
● Drive slowly onto curbs and, if possible, with the parking brake applied. If they
While driving at a right angle. Avoid driving onto high, still do not work safely, pull to the side of
sharp-edged objects and other road the road and call your BYD AUTO
Instrument: make sure the speedometer and hazards. Failure to do so can lead to service station for assistance.
- 146 -
F3/F3R OWNER’S MANUAL
● Before driving, make sure the parking braking on a slippery surface. When running on the wet surface, please
brake is fully released and the Sudden acceleration or engine avoid plashes. If much water enters the
parking brake reminder light is off. braking could cause the vehicle to engine compartment, the engine or
● After starting the engine, do not go skid or spin. electric components will be damaged.
out of the vehicle. ● Do not poke your head or arms Driving tips in winter
● Do not keep your foot on brake pedal. out of any window during driving. Make sure your coolant is properly
Otherwise, it will cause over-heat, Take special care when children protected against freezing.
abrasion, and poor fuel economy. stay inside. Use the coolant which is appointed by BYD
● To drive down a long or step hill, AUTO only.
reduce your speed and downshift. Do not continue normal driving when the
NOTICE
Remember, if you ride the brakes brakes are wet. If they are wet, your
Do not use too much plain water, since it
excessively, they may overheat and vehicle will require a longer braking
would be likely to damages the cooling
not work properly. distance, and it may pull to one side when
system of engine in winter.
● Be careful when accelerating, the brakes are applied. Also, the parking
Check the condition of the battery and
brake will not hold the vehicle securely.
cables.
Cold temperature reduces the capacity of any
- 147 -
F3/F3R OWNER’S MANUAL
battery, so it must be in top shape to provide locks to keep them from freezing. accumulated in and around the parking brake
enough power for winter starting. Section7-3 mechanism may freeze, making it hard to
tells you how to visually inspect the battery. Use cleaner containing anti-freezing release.
Your BYD AUTO service station will be agent.
pleased to check the level of charge. This product is available at your BYD AUTO Keep ice and snow from accumulating
service station and most parts stores. Follow under the fenders.
Make sure the engine oil viscosity is the manufacturer’s directions to mix the water Ice and snow built up under your fenders can
suitable for the cold weather. with agent. make steering difficult. During bad winter
See Section 7-2 for recommended viscosity. NOTICE driving, stop and check under the fenders
Leaving much summer oil in your vehicle Do not use engine antifreeze or any occasionally.
during winter months may cause harder other substitutes because it may
starting. If you are not sure about which oil to damage your vehicle’s paint.
use, Do not use your parking brake when there Depending on where you are driving, we
call your BYD AUTO service station. We will is a possibility it could freeze. recommend you to carry some emergency
be pleased to help. When parking, put the transmission into equipment. Some of the objects you might
Keep door locks from freezing. some gear and block the rear wheels. Do not put in the vehicle are tire chains, window
Squirt the lock deicer or glycerine into the use the parking brake, or snow or water scraper, bag of sand or salt, flares, small
- 148 -
F3/F3R OWNER’S MANUAL
shovel, jumper cables, etc. daggling capability is within the weight one should be the sum of length of
limitation. the two vehicles. Thus, it would be
Daggling other vehicles This capability is measured on horizontal avoided to lose control upon
BYD F3 is designed for carrying passengers. road. Remember that the engine power and slippage.
Daggling other vehicles will affect its daggling capability will decrease when driving
operation, performance, brake, durability and on mountain area.
fuel economy. The driving safety and comfort
completely depend on correct using and Tire
driving habits. Do not overload and daggle for CAUTION ● Make sure that the tire has appropriate
your and others safety. BYD AUTO does not The weight of vehicle being daggled air pressure. See Section 7-2 for
offer guarantee should not exceed the maximal rated recommendation.
for the damage or malfunction due to weight. Otherwise, an accident would ● Please keep vehicle’s tire pressure
daggling with commercial purposes. be caused. Because the braking under the standard which is set by the
Weight limitation distance may be increased, you producer, according to the total weight
Before daggling other vehicles, makes sure should enlarge the distance between of the vehicle.
the daggling capability. You can contact BYD vehicles when daggling at a speed of Wear-in procedure
AUTO service station to confirm whether the 10 km/h. The least distance to front BYD AUTO company suggest you not to
- 149 -
F3/F3R OWNER’S MANUAL
daggle other vehicles in the initial 2,000 pressure. Under inflation causes tire long wait and you are not in traffic, it is
km if it is a new one or has new driving wear and wastes fuel. See Section 7-2 better to turn off the engine and start it
system spare parts (engine, transmission, for instructions. again later.
differential, wheel bearing, drive shaft)
● Do not carry unneeded weight in your ● Avoid engine lugging or over-running.
Maintenance vehicle. Excess weight puts a heavier Use a gear position suitable for the road
● If daggling is needed, vehicle has to be load on the engine, causing greater fuel on which you are traveling.
maintained much frequently because of consumption. ● Avoid continuous speeding up and
the added load. ● Avoid lengthy warm-up idling. Once slowing down. Stop-and-go driving
the engine is running smoothly, begin wastes fuel.
How to save fuel and make your vehicle driving but gently. Remember, however, ● Avoid unnecessary stopping and
last longer that on cold winter days this may take a braking. Maintain a steady pace. Try to
Improving fuel economy is easy, so just take little longer. time the traffic signals so you only need
it easy. It will help make your vehicle last ● Accelerate slowly and smoothly. to stop as possible or take advantage of
longer, too. Here are some specific tips on Avoid jackrabbit starts. Get into high through streets to avoid traffic lights.
how to save money on both fuel and repairs: gear as quickly as possible. Keep a proper distance from other
● Keep your tires inflated at the correct ● Avoid long engine idling. If you have a vehicles to avoid sudden brakes. This
- 150 -
F3/F3R OWNER’S MANUAL
will also reduce wear on you brakes. wear but also puts an extra load on the conditions, have your vehicle receive
engine, more frequent maintenance. See Section
● Avoid heavy traffic or traffic jams which, in turn, wastes fuel. 6.
whenever possible. ● Keep the bottom of your vehicle free
CAUTION
● Do not rest your foot on the clutch or from mud, etc. This not only lessens
Never turn off the engine to coast
brake pedal. This causes premature weight but also helps prevent corrosion.
down hills. Your power steering and
wear, overheating and poor fuel ● Adjust your vehicle and have it work brake booster will not function without
economy. in best operating state. A dirty air the engine running. Also, the emission
control system operates properly only
● Maintain a moderate speed on cleaner, carburetor out of adjustment,
when the engine is running.
highways. The faster you drive, the improper valve clearance, dirty plugs,
greater the fuel consumption. By dirty oil, and grease, brakes not
reducing your speed, you will cut down adjusted, and other conditions will lower
on fuel consumption. the engine performance and lead to
● Keep the front wheels in proper poor fuel economy. For longer life of all
alignment. Avoid hitting the curb. Slow parts and lower operating costs, keep all
down on rough roads. Improper maintenance work on schedule. If you
alignment not only causes faster tire often drive under severe
- 151 -
F3/F3R OWNER’S MANUAL
Section 4 In Case of an Emergency
- 152 -
F3/F3R OWNER’S MANUAL
If your vehicle fails to start If the engine is not turning over or is NOTICE
(a) Simple checks turning over too slowly― Do not pull-start or push-start the
Before making these checks, make sure you 1. Check whether the battery terminals are vehicle. It may damage the vehicle or
have followed the correct starting procedure tight and clean. cause a collision when the engine
given in “How to start engine” in Section 3 2. If the battery terminals are OK, switch starts. The three-way catalytic
and that you have sufficient fuel. Please on the interior light. If the light goes out, converter may overheat and become a
check whether other keys can start engine. If dims, or the battery is discharged when fire hazard.
the engine can be started, then the key may the starter is cranked. You may try jump
be damaged. Contact your BYD AUTO starting. See “(c) Jump starting” for If the engine turns over at its normal
service station to inspect the key. If all the further instructions. speed but will not start―
keys can not work, then there are malfunction If the light is OK, but the engine still will not 1. Turn the ignition key to “ACC” or “LOCK”
to keys or ignition switch. Please contact start, it needs adjustment or repair. Call your and try starting the engine again.
BYD AUTO service station. See “Keys” in BYD AUTO service station. 2. If the engine will not start, the engine
Section 1-2 for reference. may be flooded because of repeated
cranking. See “(b) Starting a flooded
engine” for further instructions.
- 15 3 -
F3/F3R OWNER’S MANUAL
If this happens, turn the key to “START” with when jump starting, and avoid
damages to your vehicle which might
the accelerator pedal fully depressed. Keep spilling acid on your skin, clothing,
result from battery explosion, acid burns,
or vehicle.
the key and accelerator pedal in these electrical burns, or damaged electronic
● If you should accidentally get acid
positions for 15 seconds and release them. components, these instructions must be
on yourself or in your eyes, remove
Then try starting the engine with your foot off followed
the contaminated clothing and flush
the accelerator pedal. precisely.
the affected area with water
If the engine does not start after 15 seconds If you are unsure about how to follow this immediately. Then get immediate
of cranking, release the key, procedure, we strongly recommend that you medical attention. If possible,
wait a few minutes and try again. seek the help of a competent mechanic or continue to apply water with a
If the engine still fails to start, it needs towing service. sponge or cloth while on route to
adjustment or repair. Call your BYD AUTO the medical office.
service station for assistance. The gas normally produced by a battery
- 154 -
F3/F3R OWNER’S MANUAL
will explode if a flame or spark is brought to people. d. Connect the clamp at the other end of the
near. Use only standardized jumper 3. If the engine in the vehicle with the negative (block) jumper cable to a solid,
cables and do not smoke or light a match booster battery is not running, start it stationary, unpainted, metallic point of the
upon jump starting. and let it run for a few minutes. During
vehicle with the discharged battery.
NOTICE jump starting, run the accelerator pedal
The battery used for boosting must be by lightly pressing it at the running
12 V. Do not jump start unless you are speed of 2,000 rpm.
sure that the booster battery is correct. 4. Connect wires basing on the sequence
of a, b, c, and d.
Jump starting procedure a. Connect the clamp of the positive (red)
1. If the booster battery is installed in jumper cable to the positive
another vehicle, make sure the vehicles
terminal (+) on the discharged battery.
are not touching. Turn off all
b. Connect the clamp at the other end of the
unnecessary lights and accessories.
positive (red) jumper cable to the positive
2. If necessary, remove all the plugs of
terminal (+) on the booster battery.
the battery for charging and discharged
battery, and cover a cloth on the c. Connect the clamp of the negative (black)
openings of the battery. This can help jumper cable to the negative terminal (-) on
reduce explosion possibility and injury the booster battery.
- 155 -
F3/F3R OWNER’S MANUAL
Do not connect the cable to or near any part the battery: they may now contain
that moves when the engine is cranked. sulfuric acid.
clamps touch anything except the apparent (for example, lights left on), you
Below shows the connecting point: correct battery terminals or the ground. should have it checked at your BYD AUTO
service station.
- 156 -
F3/F3R OWNER’S MANUAL
If your engine stalls while driving CAUTION 1. Pull safely over the road, park your
1. Decelerate your vehicle gradually, and If the engine is not running, the power vehicle, and turn on your emergency
keep moving in a straight line. Move assist for the brakes and steering will flashers. Put the transmission on neutral
cautiously off the road to a safe place. not work so steering and braking will be and apply the parking brake. Turn off the
2. Turn on your emergency flashers. much harder than usual. air conditioning if it is being used.
- 157 -
F3/F3R OWNER’S MANUAL
2. If coolant or steam is boiling out of the bring it up to half full again. Serious
CAUTION
radiator or reservoir, stop the engine. coolant loss indicates a leak in the
When the engine is running, keep
Wait until the steam system. You should
hands and clothing away from the
subsides and open the engine hood. If
moving fan and engine drive belts. have it checked as soon as possible at your
there is no coolant or steam boiling over,
BYD AUTO service station.
leave the engine running and make sure
If you have a flat tire
the electric cooling fan is operating. If it is 4. If the engine drive belt is broken or the
not, turn the ignition switch off. 1. Decelerate your vehicle gradually and
coolant is leaking, stop the engine
CAUTION keep moving in a straight line. Move
immediately. Call a BYD AUTO service
To help avoid personal injury, keep the cautiously off the road to a safe place
station for assistance.
hood closed until there is no steam. well away from the traffic. Avoid
5. If there are no obvious leaks, check the
Escaping steam or coolant is a sign of stopping on the center divider of a
coolant reservoir. If it is dry, add coolant
very high pressure. highway. Park in a level spot with firm
to the reservoir while the engine is
ground.
running. Fill it between the two lines.
3. Look for obvious coolant leaks
2. Stop the engine and turn on your
from the radiator, hoses and under the 6. After the engine coolant temperature
emergency flashers.
vehicle. However, water draining from has cooled to normal, check the coolant
the air conditioning is normal if it has 3. Firmly set the parking brake and put the
level in the reservoir again. If necessary,
been used. transmission in neutral.
- 158 -
F3/F3R OWNER’S MANUAL
4. Have everyone get out of the vehicle on transmission in neutral. Block the ● Raise the vehicle only high
the side away from wheel diagonally opposite to the enough to remove and change the
5. Read the following instructions ● Make sure to set the jack properly
in the jack point. Raising the NOTICE
thoroughly.
vehicle with a jack improperly Do not continue driving with a deflated
CAUTION
positioned will damage the vehicle tire. Driving even a short distance can
Upon jacking, be sure to observe the
or may allow the vehicle to fall off damage a tire and wheel beyond
following to reduce the possibility of
the jack and cause personal injury. repair.
personal injury:
● Follow jacking instructions. ● Never get under the vehicle when
● Do not put any part of your body the vehicle is supported by the jack
under the vehicle supported by the alone.
jack. Otherwise, personal injury may ● Use the jack only for lifting your
occur. vehicle during wheel changing.
● Do not start or run the engine while ● Do not raise the vehicle with
your vehicle is supported by the jack. someone in the vehicle.
● Stop the vehicle on a level firm ● When raising the vehicle, do not
ground, firmly set the parking brake,
place any objects on top of or
and put the
underneath the jack.
- 159 -
F3/F3R OWNER’S MANUAL
Required tools and spare tire and their storage locations.
Turn the jack joint by hand To remove the spare tire: loosen the bolt and
Get the required tools and spare tire. To remove: turn the joint in direction 1 until remove it.
1. Tool bag the jack is free. When storing the spare tire, put it in place
2. Jack To store: turn the joint in direction 2 until the with the outer side of the wheel facing up.
3. Spare tire jack is firmly secured to prevent it flying Then, secure the tire by repeating the above
To prepare yourself for an emergency, you forward during a collision or suddenly removal steps in reverse order to prevent it
should familiarize yourself with the use of the braking. from flying forward during a collision or
jack, each of the tools suddenly braking.
- 160 -
F3/F3R OWNER’S MANUAL
Blocking the wheel Loosening wheel nuts Be careful that the wrench does not slip off
the nut.
Do not remove the nuts yet: just unscrew
them about one-half turn.
CAUTION
- 161 -
F3/F3R OWNER’S MANUAL
Positioning the jack Raising your vehicle clockwise. As the jack
touches the vehicle and begins to lift,
double-check whether it is properly
positioned.
CAUTION
Position the jack at the correct jack point After making sure that no one is in the
as shown above. vehicle, raise it high enough so that the
Make sure that the jack is positioned on a spare tire can be installed.
level and solid place. Remember, it needs wider distance from the
ground to fix spare wheel than to take the flat
one off.
To raise the vehicle, insert the jack handle
into the jack (it is a loose fit) and turn it
- 162 -
F3/F3R OWNER’S MANUAL
Changing wheels Re-installing all wheel nuts
Remove the wheel nuts and change the Before putting on wheels, remove any Reinstall the wheel nuts with the tapered end
tire. corrosion on the mounting surfaces with a inward and tighten them as much as you can
Lift the flat tire straight off and put it aside. wire brush or such. Installation of wheels by hand. Push on tire back and see if you can
Roll the spare wheel into position and align
without good metal-to-metal contact at the tighten them more.
the holes in the wheel with the bolts. Then lift
mounting surface can cause wheel nuts to
up the wheel and get at least the top bolt
started through its hole. Wiggle the tire and loosen and eventually cause a wheel to come
press it back over the other bolts. off while driving.
- 163 -
F3/F3R OWNER’S MANUAL
Lowering your vehicle wrench is securely engaged over the nut.
Never use oil or grease on the bolts or shown. Repeat the process until all the nuts
- 164 -
F3/F3R OWNER’S MANUAL
CAUTION designated in Section 8. If the pressure is wrench. Have a technician repair the flat tire.
● When lowering the vehicle, make lower than specified, drive slowly to the CAUTION
sure all portions of your body and all nearest station and fill to the correct Before driving, make sure all the tools,
other persons around will not be pressure. the jack, and flat tire are securely
injured as the vehicle is lowered to Do not forget to reinstall the tire inflation valve placed in place in their storage
the ground. cap as dirt and moisture could get into the location to reduce the possibility of
● Have the wheel nuts tightened with valve core and possibly cause air leakage. If personal injury during a collision or
torque wrench to 103N•m (10.5kgf•m), the cap is missing, have a new one put on as suddenly braking.
as soon as possible after changing soon as possible.
Adjust the air pressure to the specification torque specified in Section 8 with a torque
- 165 -
F3/F3R OWNER’S MANUAL
Do not attempt to rock the vehicle free by the correct procedure, it is possible to make a
moving it forward and backward if people mistake. To avoid damages to your vehicle,
or objects are anywhere near the vehicle. make sure the following precautions are
During the rocking operation, the vehicle observed. If necessary, show this page to the
If your vehicle needs to be towed Use a safety chain system for all towing, and
abide by the state/provincial and local laws.
The wheels and axle on the ground must be
in good condition. If they are damaged, use a
towing dolly.
NOTICE
Proper equipment will help ensure that your Not allow to tow vehicle with AT from its
rear.
vehicle is not damaged while being towed.
Your vehicle can be damaged if it is towed Emergency towing
- 166 -
F3/F3R OWNER’S MANUAL
paid upon vehicle towing. A driver must sit in the vehicle to steer it
and operate the brakes.
Towing in this manner may be done only on
When temporarily tow vehicle with AT,
hard-surfaced roads for a short distance and
shift the gear into “N”, Speed should be
at low speeds. Also, the wheels, axle, drive
less than 30km/h, and the towing
train, steering, and brakes must all be in good
distance is less than 10Km
condition.
NOTICE
CAUTION
If towing is necessary, we recommend ● Only use specified towing eyelet; Special attention should be paid upon
you to have it done by your BYD AUTO otherwise, your vehicle may be vehicle towing. Avoid sudden starts or
● Never tow a vehicle from the rear place excessive stress on the
If towing service is not available in an
with four wheels on the ground. emergency chain. The eyelets and
emergency, your vehicle may be
towing cable or chain may break and
temporarily towed by a cable or chain This may cause serious damage
cause serious injury or damage.
secured to one of he emergency towing to the transmission.
- 167 -
F3/F3R OWNER’S MANUAL
Notice CAUTION
Only the specified cables or chains If the engine is not running, the power
for draggling are available and they assist for the brakes and steering will
not work so the steering and braking
will link the pothook of the vehicle
will be much harder than usual.
tightly.
- 168 -
F3/F3R OWNER’S MANUAL
Section 5 Corrosion Precaution and Appearance Care
- 169 -
F3/F3R OWNER’S MANUAL
Protecting your BYD F3 from corrosion ● Saline soil or dust containing chemicals The above signifies the necessity to keep
Proper care of your BYD F3 can help ensure will accelerate corrosion, as will the your vehicle, particularly the under side, as
long-term corrosion protection. presence of salt in the air near the clean as possible and to repair any damage
seacoast or in areas of industrial to paint or protective coatings as soon as
The most common causes of corrosion to pollution. possible.
your vehicle are: ● High humidity accelerates corrosion
● The accumulation of saline soil, dust, especially when the temperature ranges To help prevent corrosion on your BYD F3,
and moisture in hard-to-reach areas just above the freezing point. follow these guidelines:
under the vehicle. ● Wetness or dampness to certain parts of Wash your vehicle frequently. It is, of
● Chipping of paint or undercoating your vehicle for an extended period of course, necessary to keep your vehicle clean
caused by minor accidents or by stones time may cause corrosion even though by regular washing, but to prevent corrosion,
and gravel. other parts of the vehicle may be dry. the following
points should be observed:
Care is especially important if you live in ● High ambient temperatures can cause ● If you drive on saline fields in the winter
particular areas or operate corrosion to those components of the or if you live near the ocean, you should
your vehicle under certain environmental vehicle which does not dry quickly due hose the under carriage at least once a
conditions: to lack of proper ventilation. month to minimize corrosion.
- 170 -
F3/F3R OWNER’S MANUAL
● High pressure water or steam is Check the condition of your vehicle’s dry the area.
effective for cleaning the vehicle’s paint and trim.
underside and wheel housings. Pay If you find any chips or scratches in the paint, Use mud shields on your wheels. If you
particular attention to these areas as it is fix them up immediately to prevent corrosion drive on salted or gravel roads, mud shields
difficult to see all the mud and dirt. It will from starting. If the chips or scratches have help protect your vehicle. Full-size shields,
do more harm by simply wetting the mud gone through the bare metal, have your BYD which come as near to the ground as
and debris without removing. The lower AUTO service station make the repair. possible, are the best.
edge of doors, rocker panels, and frame We recommend that the fittings and the area
members have drain holes which should where the shields are installed be treated to
Check the interior of your vehicle. Water
not be allowed to clog with dirt as resist corrosion. Your BYD AUTO service
and dust can accumulate under the floor
station will be happy to assist in supplying
trapped water in these areas can mats and could cause corrosion.
and installing the shields if they are
cause corrosion. Occasionally check the underside of the mats
recommended for your area.
● Wash the under side of the vehicle to make sure the area is dry. Be particularly
- 171 -
F3/F3R OWNER’S MANUAL
garage, or if you drive it covered with water or become higher and higher, thus the paint. Wash the vehicle everyday if you
snow, your garage may be so damp as to paint will be corroded as time passes if drive in coastal areas or at
cause corrosion. Even if your garage is you don’t wash the stains with clean places with heavy pollution.
heated, a wet vehicle can corrode if the water. (4) Use clean and soft cloth or sponge to
ventilation is poor. (3) Wash the vehicle when the motor has wash the vehicle and avoid mixing metal
cooled down. Do not wash the vehicle scraps and sand particles. Do not use
Painting area maintenance tips under burning sun or high temperature. dry cloth, dry towel, or dry sponge to
Pay attention to the following regulations in Otherwise, the detergent will be dried clean the vehicle to avoid scratching.
the application and maintenance process of and leave vestige. If you wash your Follow the water flow direction and wipe
the vehicle: vehicle by yourself, use special neutral from top to bottom. Do not wipe
(1) Clean the dust on the vehicle before, detergent only, and do not use washing circularly or transversally.
during, and after using your BYD F3 and powder or soapsuds with high alkali (5) Clean the special high corrosive
try to reduce the dust absorption due to content to avoid scouring off the grease vestiges (e.g. asphalt, guano, and
static electricity. in the paint and accelerating the aging of insects) immediately. Use special
(2) Wash in time after rain. The raindrop
paint. If the vehicle is washed in car detergent to clean. Do not use a blade
stains on the vehicle body after rain will
washing park, ask the washer not to use to scrape or use gasoline to clean so as
become smaller and smaller and the
dewaxing detergent so as to protect the to protect the paint.
concentration of acidic material will
- 172 -
F3/F3R OWNER’S MANUAL
(6) Do not touch the paint with smeary (10) Use carbon detergent to clean plating ● When driving in a coastal area, the paint
hands or wipe the paint with oily rag. Do metal parts and wax regularly. layer may go off
not put tools with smear or rag with (11) Use high quality detergent to clean the ● When driving on a road sprinkled with
organic solvents on the vehicle so as to decoration parts. Do not wipe too heavy antifreeze
avoid chemical reaction. when waxing to avoid penetrating the ● When exposed to coal tar, tree sap, bird
(7) If there are no obvious scratches, do not paint layer. droppings and carcass of an insect
spray new paint to avoid incongruent Wax the paint randomly and maintain in ● When driving in areas where there is a
paint colors or bad combination. professional auto maintenance shop regularly lot of smoke, soot, dust, iron, dust or
(8) If you won’t use the vehicle for a long (once every season) so as to resume the chemical substances
time, park it in the garage or at places gloss of the paint in time. ● When the vehicle becomes remarkably
with good ventilation. Put on a special dirty with dust and mud
vehicle cover in winter. For temporary Washing and waxing Hand-washing your BYD F3R
parking, select cool area. Washing your BYD F3/F3R Work in the shade and wait until the vehicle
(9) Do not impact, knock on or scratch paint Keep your vehicle clean by regular body is not hot to the touch.
film. Repair the damage, depression, or washing. CAUTION
cast of the paint in time in a professional Wash your vehicle as soon as possible upon When cleaning under the floor or
chassis, be careful not to injure your
auto maintenance store. corrosion. hands.
- 173 -
F3/F3R OWNER’S MANUAL
1. Rinse off loose dirt with a hose. Remove using a clean soft cotton towel. Do not Plastic bumpers: wash carefully. Do not
any mud or road salt from the underside rub or press hard. You might scratch the scrub with abrasive cleaners. The bumper
instructions, use a ornaments are damaged easily by organic that are marked safe for painted surfaces.
soft cotton mitt, and keep it wet by substances. If any organic substances splash NOTICE
dipping it frequently onto the wash water. an ornament, be Do not use organic substances
Do not rub hard. Let the soap and water sure to wash it off with water and check if the (gasoline, kerosene, benzene, or
remove the dirt. ornament is damaged. strong solvents) which may be toxic or
3. Rinse thoroughly. Dried soap can cause CAUTION cause damage.
streaks. You may need to rinse each Do not attach the heavily damaged
section right after you wash it in hot plastic wheel ornament. It may fly off Automatic washing station
the wheel and cause accidents while
weather. Your vehicle can be washed in
the vehicle is moving.
4. To prevent water spots, dry the vehicle automatic washing station. But be attentive
Aluminum wheels: use only a mild soap or
that some type of brushes, unfiltered rinsing
neutral detergent.
water, or custom rinsing procedure would
- 174 -
F3/F3R OWNER’S MANUAL
scrape the paint. a combined cleaner and wax. Cleaning the interior
If scraped, the durability and polish of paint 2. Use a good quality polisher and wax. If CAUTION
will be reduced. When washing vehicles, the finish has become Do not wash the vehicle floor with
especially fuscous ones, workers in washing extremely weathered, use a car-cleaning water, or allow water to get onto the
station will tell you the most suitable washing polisher, and follow the manufacturer’s floor when cleaning the interior or
procedure for the sake of protecting paint. instructions and precautions. Be sure to exterior of your vehicle. Water may get
polish and wax the chrome trim as well into audio components above or under
Waxing your BYD F3 3. Wax the vehicle again when water does malfunction; and it may cause body
- 175 -
F3/F3R OWNER’S MANUAL
cleaners are available; some are in an CAUTION instrument panel, console panel, and
aerosol cans ● Do not use dye or bleach on the switches
and others are powers or liquids which you belts. It may weaken them. Use soft damp cloth for cleaning. Soak a
mix with water to produce foam. To shampoo ● Do not use the belts until they piece of clean soft cloth in water or lukewarm
the carpets, use a sponge or brush applied become dry. water. Then, lightly wipe off dirt.
with foam to rub in overlapping circles.
Do not apply water. The best results are Windows
obtained by keeping the carpet as dry as The windows may be cleaned with any
possible. Read the shampoo instructions and household window cleaner.
follow them strictly. NOTICE
● Do not use organic substances
Seat belts NOTICE (solvents, kerosene, alcohol, gasoline,
The seat belts may be cleaned with a mild When cleaning the inside of the rear etc.) or alkaline or acidic solutions.
soap and water or with lukewarm water. window, be careful not to scratch or These chemicals can cause
Use a sponge or soft cloth. As you are damage the heater wires or connectors. discoloring, staining or peeling of the
- 176 -
F3/F3R OWNER’S MANUAL
agents, make sure their ingredients do all traces of detergent with a piece of clean
CAUTION
not include the substances mentioned damp cloth.
● If a stain should fail to come out with
above. After cleaning or whenever any part of the
a neutral detergent, apply a cleaner
● If you use a liquid car freshener, do leather gets wet, dry with a piece of soft clean
that does not contain an organic
not spill the liquid onto the vehicle’s cloth. Allow the
solvent.
interior surfaces. It may leather to dry in a ventilated shaded area.
● Never use organic substances such
contain the ingredients mentioned
as benzene, alcohol, gasoline,
above. Immediately clean any spill
alkaline or acid solutions to clean the
using the method mentioned above.
leather as these could cause
discoloring.
The leather upholstery may be cleaned with fiber cloth, etc. may scratch the fine
Remove dirt using a piece of soft cloth ● Mildew may develop on soiled
- 177 -
F3/F3R OWNER’S MANUAL
especially careful to avoid oil spots. If you have any questions about the cleaning
Try to keep your upholstery always of your BYD F3, your BYD AUTO service
- 178 -
F3/F3R OWNER’S MANUAL
Section 6 Maintenance Requirements
Maintenance ……………………………………………………………………………………………………………177
Does your vehicle need repairing?………………………………………………………………………………………….178
BYD F3/F3R maintenance schedule………… …………………………………………………………………………...179
- 179 -
F3/F3R OWNER’S MANUAL
Maintenance often. To make sure your vehicle runs at peak department will perform all of the scheduled
Regular maintenance is essential. efficiency, follow the maintenance schedule. maintenance on your vehicle reliably and
We urge you to protect your vehicle by having economically.
your BYD serviced according to the Where to go for service? What maintenance can be operated by
maintenance schedule given on the following It makes good sense to take your vehicle to driver?
pages. Regular maintenance will contribute your BYD AUTO service station for service. Much maintenance can be operated by driver
to: BYD technicians are well-trained specialists.
who has commanded some mechanism
● Good fuel economy And they are receiving the latest service
knowledge and basic auto-repairing tools.
● Long vehicle life information through technical bulletins,
See Section 7 for reference about “How to
● Enjoying driving service tips, and inner training programs.
maintain your car by yourself”.
● Safety They learn to work on BYD Before they work
● Reliability on your vehicle, rather than while they are Note that part of the maintenance need to be
● Warranty coverage working on it. Is it not the best operated with special tools and technique.
● Compliance with government way? Thus, it had better be operated by qualified
regulations Your BYD AUTO service station has invested technicians. Even if the driver is an
Your BYD F3 has been designed for much in special BYD tools and service experienced technician, BYD AUTO
economical driving and maintenance. equipment. It helps do the job better at less
Company still suggests that repair and
Many formerly required maintenance items cost.
maintenance should be done by BYD AUTO
are no longer required or are not required as Your BYD AUTO service station’s service
service station by whom the maintenance will
- 180 -
F3/F3R OWNER’S MANUAL
be recorded. This record will be helpful when indicate a dangerous carbon monoxide If you notice any of these clues, take your
your vehicle needs repair or maintenance leak. Drive with the windows opened vehicle to your BYD service station as soon
service. and have the exhaust system checked as possible. It probably needs adjustment or
immediately.) repair
Does your vehicle need repairing? ● Flat-looking tire; excessive tire squeal
CAUTION
Be on the alert for changes in when cornering; uneven
Do not continue driving with the
performance, sounds, and visual tip-offs tire wear vehicle unchecked. It could result in
that indicate service is ● Vehicle pulls to one side when driving serious vehicle damage and possibly
personal injury.
needed. Some important clues are straight on a level road
as follows: ● Strange noises related to suspension
BYD F3/F3R maintenance schedule
● Engine missing, stumbling, or pinging movement
BYD F3/F3R maintenance schedule helps
● Obviously decreasing of power ● Loss of brake effectiveness; spongy
guarantee steady, safe, and economic
● Strange engine noises feeling upon brake or clutch petal; pedal
driving and reduce malfunctions.
● A leak under the vehicle (however, almost touches floor; vehicle pulls to
The service interval for scheduled
water dripping from the air conditioning one side when braking
maintenance bases on the odometer reading
after use is normal.) ● Engine coolant temperature stays
or time interval. The one that comes first
● Change in exhaust sound (this may continually higher than normal
prevails.
- 181 -
F3/F3R OWNER’S MANUAL
- 182 -
F3/F3R OWNER’S MANUAL
If you mainly operate your BYD F3/F3R under one or more of the special operating conditions below, some of the maintenance schedule items
need to be serviced more frequently.
- 183 -
F3/F3R OWNER’S MANUAL
Maintenance schedule
Maintenance operations: I = Inspect and correct or replace as necessary; R = replace, change or lubricate, C= Clean
Maintenance interval Odometer reading or months, whichever comes first
* 1000km 3 8 13 18 23 28 33 38 43 48 53 58 63 68 73
Maintenance items Number of
Months F 3 6 9 12 15 18 21 24 27 30 33 36 39 42
BASIC ENGINE COMPONENTS
1. Check whether drive belts break or wear
I I I I I I I I
and adjust the intensity
2. Check whether the ignition cable is damaged I I I
3. Replace the timing belt Normal condition I I I R
for engine Harsh condition R: Every 70,000 km
4. Check whether the crankcase fuel control
I I I
system works properly
5. Check and replace the spark plug I I R I I R I
6. Check whether the coolant pipe is damaged
and make sure that the connection are locked I I I I
securely
7. Check the liquid level in the reservoir I I I I I I I I
8. Replace the coolant liquid R R R
9. Check whether the air Normal condition I I I I I I I I I I I I I I
filter core is blocked or
damaged Harsh condition I: Shorten the cycle as the actual condition
10. Replace the air filter Normal condition R R R R R R R
core Harsh condition R: Shorten the cycle as the actual condition
- 184 -
F3/F3R OWNER’S MANUAL
- 185 -
F3/F3R OWNER’S MANUAL
- 186 -
F3/F3R OWNER’S MANUAL
Note:
“Harsh condition” standard only applies to vehicles used in harsh conditions. “Harsh conditions” are listed below:
(1) Drive in dusty areas, or expose your vehicle to salty air or seaside.
(2) Drive through scraggly roads, plashes or mountain roads.
(3) Drive in the cold areas.
(4) In cold whether, the engine is idling for a long time or the vehicle is moving for short distance frequently.
(5) Brake your vehicle suddenly and frequently.
(6) The vehicle is used to daggle other vehicles.
(7) The vehicle is used as a taxi or a leasehold vehicle.
(8) At 32°C or above, the driving time in the heavy traffic area goes beyond half of the total driving time.
(9) At 30°C or above, the driving time at a speed of 120 km/h goes beyond half of the total time.
(10) Drive at overload condition.
- 187 -
F3/F3R OWNER’S MANUAL
- 188 -
F3/F3R OWNER’S MANUAL
CNG system maintenance schedule
Your BYD F3 CNG vehicle needs to be serviced in accordance with the normal maintenance schedule
Caution
◆ Maintenance and inspecting of CNG
system should be in BYD service
shop by professional repairer.
Strictly prohibit disassembly and
repair by unprofessional personnel.
◆ Strictly prohibit checking whether
exist natural gas leak by fire.
- 189 -
F3/F3R OWNER’S MANUAL
Maintenance operation:
Maintenance period Odometer reading or months, which comes first as standard
×1,000km(KM) 5 10 20 30 40 50 60 70 80 90
Reductor strainer R
Reductor film R
Rmark
I:Inpect T :Adjust G:Replace N :lossen as standard torque J.T :Inspect and adjust
- 190 -
F3/F3R OWNER’S MANUAL
Section 7 Do-It-Yourself Maintenance
Introduction…………………………………………………………………………………………………………………..192
Engine and chassis……………………………………………………………………………………………………
……...199
Electrical components………………………………………………………………………………………………………..212
- 191 -
F3/F3R OWNER’S MANUAL
1. Introduction
Engine compartment overview……………………………………………………………………………………… ………193
Fuse locations……………………………………………………………………………………………………………….. 194
Do-it-yourself service precautions………………………………………………………………………………………….. 195
Positioning the jack………………………………………………………………………………………………………….198
- 192 -
F3/F3R OWNER’S MANUAL
Engine compartment overview
1. Junction box
5. Battery
6. Radiator
8. Condenser
- 193 -
F3/F3R OWNER’S MANUAL
Fuse locations
- 194 -
F3/F3R OWNER’S MANUAL
Do-it-yourself service precautions CAUTION prevent burning yourself.
If you perform maintenance by yourself, be ● When the engine is running, keep ● Do not leave anything that may
sure to follow the correct procedure given in hands, clothing, and tools away burn easily, such as paper or rags,
this section. from the moving fan and engine in the engine compartment.
Be aware that improper or incomplete drive belts. (Removing rings, ● Be sure that the ignition is off if you
servicing may result in operating problems. watches, and ties is advisable.) work near the electric cooling fan
This section gives instruction only for those ● Right after driving, the engine or radiator grille. With the ignition
items that are relatively easy for an owner to compartment, including the engine, on, the electric cooling fan will
perform. As explained in Section 6, there are radiator, exhaust manifold, power automatically start to run if the
still a number of items that must be done by a steering fluid reservoir and spark engine coolant temperature is high
qualified technician with special tools. plug boots, will be hot, so be and/or the air conditioner is turned
Utmost care should be taken when working careful not to touch them. Oil, on.
on your vehicle to prevent accidental injury. fluids, and spark plugs may also be ● Do not smoke for fear of causing
Here are a few precautions that you should hot. sparks or open flames around fuel
be especially careful to observe: ● If the engine is hot, do not remove or the battery. Their fumes are
- 195 -
F3/F3R OWNER’S MANUAL
working on the battery. It contains type of oil frequently. You can use ● Being harmful to eyes, the
poisonous and corrosive sulfuric soap and water to clean the oil on paint and the brake fluid
acid. your skin. should be infused carefully.
● Do not get under your vehicle with ● Put used oil in the place out of If the brake fluid spills into
just the body jack supporting it. children’s reach. your eyes, wash your eyes at
Always use automotive jack stands ● Take a secure method to deal with once. If you still feel
or other solid supports the used oil and oil filter. Do not uncomfortable with your
● Use eye protection whenever you discard them into garbage sewer eyes, go to hospital for
work on or under your vehicle or onto the ground. Contact BYD check immediately.
where you may be exposed to AUTO service station for requiring
flying or falling material, fluid how to recycle or dispose of them.
spray, etc.
● Used oil contains latent pollutant
which would cause skin diseases
such as
dermatitis and skin cancer, so pay
attention to avoid touching this
- 196 -
F3/F3R OWNER’S MANUAL
NOTICE ● Use the prescribed spark plug only. the engine compartment.
● Remember that the battery and The engine will be so damaged by ● Be careful not to scratch the glass
ignition cables carry high currents using other types of spark plugs surface with the wiper frame.
or voltages. Be careful of that it loses its function or gives off ● When closing the engine hood,
accidentally causing a short circuit. wireless interference. check whether you have left any
● If you spill some of the coolant, be ● Do not overfill automatic tools, rags, etc.
sure to wash it off with water to transmission fluid and power
prevent it from damaging the parts steering fluid. The automatic
or paint. transmission and power steering
● Do not allow dirt or anything else to could be damaged.
fall through the spark plug holes. ● If you spill the brake fluid, be sure
● Do not pry the outer electrode of a to wash it off with water to prevent
spark plug against the center it from damaging the parts of paint.
electrode. ● Do not drive with the air cleaner
filter removed, or excessive engine
wear could be caused.
Also backfiring could cause a fire in
- 197 -
F3/F3R OWNER’S MANUAL
Positioning the jack Rear ● Make sure to put the jack in a
proper position. Personal injury or
When jacking up your vehicle with the jack,
vehicle damage may occur if it is
position the jack correctly as shown in the
jacked up incorrectly.
illustrations. ● Don’t go under the vehicle if it’s
CAUTION upheld only by the jack. The
When jacking, be sure to observe the vehicle needs to be
following to reduce the possibility of underpropped.
personal injury: ● Do not raise the vehicle with
● Avoid inhale the exhaust gas of someone in the vehicle.
engine. The exhaust gas contains When raising the vehicle, do not place
colorless and odorless monoxide that any objects on top of or underneath
Front can cause deaths.
the jack.
● Do not put any part of your body
under the vehicle supported by the
jack. Personal injury may occur.
● Do not start or run the engine while
your vehicle is supported by the jack. NOTICE
● Stop the vehicle on a level firm
ground, firmly set the parking brake, Make sure to place the jack correctly, or
and put the transmission in neutral. your vehicle may be damaged.
Block the wheels on the opposite side
or the jack up point if necessary.
- 198 -
F3/F3R OWNER’S MANUAL
- 199 -
F3/F3R OWNER’S MANUAL
Checking the engine oil level
the end, and wipe it clean. adding oil.
3. Reinsert the oil dip rod, and push it in as To confirm the quantity of needed oil, please
far as it will go, or the reading will not be take reference from the interval between the
correct. low and high level on the oil dip rod.
4. Pull the oil dip rod out and look at the oil When the level reaches within the correct
level while placing a rag at the end. range, install the filler cap and tighten it by
NOTICE hand.
Be careful not to drop the engine oil on
vehicle components.
NOTICE
With the engine arrives at operating
● Do not spill oil onto spare parts.
temperature, turn it off and check the oil If the oil level goes below or slightly above
● Avoid overfilling, or the engine
level with a dipstick. the low level, fill the engine oil of the same could be damaged.
1. To get a correct reading, the vehicle
type into the engine. ● Check the oil level on the dipstick
should be on level ground. After turning once again after adding the oil.
Remove the oil filler cap and add the engine
off the engine, wait a few minutes for the
oil in small quantities at a
oil to drain back into the bottom of the Oil type selection
time, and check the oil dip rod. We
engine.
recommend that you use a funnel when Use the oil approved by BYD AUTO or
2. Pull the oil dip rod out, hold a rag under
- 200 -
F3/F3R OWNER’S MANUAL
Gear oil grade for transmission Predicted temperature range before next oil
75 W-90 Cold area (Northern), changing API classified sign
winter
If SAE 10 W-30 or higher viscosity grade is
80 W-90 Cold area (Northern),
summers applied in extremely cold day, the engine
80 W-90 or 80 W-140 warm area would be difficult to start. Thus, we
(Southern), whole year
recommend you to use SAE 5 W-30.
Dosage: 2.1 L
Recommendatory oil (SAE):
- 201 -
F3/F3R OWNER’S MANUAL
- 202 -
F3/F3R OWNER’S MANUAL
7.If the oil level is less than HOT min. pour oil If the ATF has the smell of burn, that means
from filler door to make it between hot transmission oil has been polluted by the
upper-lower limit. burned particle and friction material, and the
transmission need overhaul.
Notice : The warming up state is the
standard judging the transmission oil level. 8.Ensure that insert the full dipstick into
The cooling state the oil level should be transmission dipstick canal.
between the COLD upper-lower limit. that is Replacing the ATF is according to the stated
only to refer. driving time and mileage in the regular
Slowly and carefully adding the transmission maintenance table. Discharging the full ATF
oil, and don’t make it overfilling. And you from transmission and then pour the new
should immediately clean the oil that is ATF.
overfilling. Because it can hurt the parts in
engine chamber.
5.Ensure that insert the full dipstick into If you don’t know how to pour the ATF,
transmission dipstick canal. You should use the BYD original ATF contact the BYD AUTO authorized repair
6. Pull out dipstick and check oil level. (MITSUBISHI ATF SPⅢ)。 store.
- 203 -
F3/F3R OWNER’S MANUAL
MT store, you will find its type.
When the transmission temperature is 80℃,
and parking the vehicle in the level ground,
checking oil level. Release bolt which lie in
the transmission oil filler door, touch the oil
level in the hole of bolt with your hand. And
then oil level should lie in the margin of bolt
hole. Or you should add the BYD ATUO
original MTF till the oil overfills from filler door. Replacing transmission oil should be
And then fasten the bolt of filler door. You should immediately remove the according to the stated driving time and
overfilling oil, because the overfilling oil will mileage in the regular maintenance table.
hurt the part in engine chamber. And you should discharge the full oil from
transmission and pour the new transmission
If you can’t buy the BYD AUTO original MTF, oil.
the API gear oil is recommended as the If you don’t know how to check the oil level
substitute. Refer to maintenance manual or and adding oil, contact the BYD AUTO
contact the BYD AUTO authorized repair authorized repair store.
- 204 -
F3/F3R OWNER’S MANUAL
The coolant level in the reservoir varies with AUTO and choose suitable coolant according
the engine temperature. However, if the level to the temperature.
goes above or below the “LOW” line, you Use improper coolant will destroy the engine
should add coolant to bring the level up to the cooling system.
“FULL” line. CAUTION
If the coolant level drops within a short time Do not use too much plain water in
winter, because engine cooling
after replenishing, there may be a leak in the
system would be damaged in this way.
system. Visually check the radiator, hoses,
radiator cap and drain cock and water pump.
If no leak is found, contact your BYD AUTO
Checking the engine coolant level For details, please contact your BYD AUTO
service station to test the cap pressure and service station.
Look at the see-through coolant reservoir
check whether the cooling system is leaking.
when the engine is cooled. The coolant
CAUTION
level is satisfactory if it stays between the
To prevent burns, do not remove the
“FULL” and “LOW” lines on the reservoir.
radiator cap when the engine is hot.
Upon a lower level, add the coolant. For
the coolant type, see “Coolant type Coolant type selection
selection” described below. Only use the coolant approved by BYD
- 205 -
F3/F3R OWNER’S MANUAL
Checking the radiator and condenser Checking tire inflation pressure CAUTION
If any of the above parts are extremely dirty Keep your tire inflation pressures at a Keep your tires properly inflated.
or you are not sure of their condition, take Otherwise, the following conditions
proper level.
may occur and cause an accident
your vehicle to your BUD AUTO service Refer to Section 8 for the recommended cold
resulting in serious injuries or deaths.
station. tire inflation pressures and tire sizes. Low tire pressure (under-inflation):
CAUTION You should check the tire inflation pressure ● Excessive wear
To prevent burns, be careful not to ● Abnormal wear
every two weeks, or at least once a month.
touch the radiator or condenser when ● Poor handling
And do not forget the spare.
the engine is hot. ● Possibility of blowouts from
Incorrect tire inflation pressure may waste overheated tire
fuel, reduce driving comfort, shorten tire life, ● Poor sealing of the tire bead
NOTICE and make your vehicle less safe to drive. ● Wheel deformation and/or tire
To prevent damaging the radiator and separation
If a tire frequently needs refilling, have it
condenser, do not perform the work by High tire pressure (over-inflation)
checked by your BYD AUTO service station. ● Poor handling
yourself.
● Excessive wear
● A greater possibility of tire
damages from road hazards
- 206 -
F3/F3R OWNER’S MANUAL
The following instructions for checking tire normal for the tire inflation pressure to Checking and replacing tires
- 207 -
F3/F3R OWNER’S MANUAL
If air loss occurs while driving, do not seriously affect handling, riding,
wears to 1.6 mm or less, you will see the continue driving. Driving even a short speedometer/odometer calibration, ground
indication mark. If you find the indicators in distance can damage a tire beyond repair. clearance, clearance, and the clearance
two or more adjacent grooves, the tire should between the body and tires or snow chains.
Any tires which are over 6 years old must
be replaced. The thinner the tread is, the
be checked by a qualified technician even CAUTION
higher the risk of skidding is.
if the damage is not obvious. Observe the following instructions.
If the tire tread is worn to 4 mm or below,
Tires deteriorate with age even if they have Otherwise, an accident may occur
the snow tire function will be lost.
resulting in serious injuries or deaths.
never or seldom been used.
If you have tire damage such as cuts, ● Do not mix radial, bias belted, or
This applies also to the spare tire and tires bias-ply tires on your vehicle, as
splits, cracks deep enough to expose the
stored for future use. this may cause dangerous
fabric, or bulges indicating internal
handling characteristics resulting
damage, the tire should be replaced. in loss of control.
Replacing your tires ● Do not use tires other than the
If a tire often goes flat or can not be properly
When replacing a tire, use a tire of the manufacture’s recommended
repaired due to the size or location of a cut or
same size and construction, and the same size, as this may cause
other damaged, it should be replaced. If you dangerous handling
or greater load capacity as the originally
are not characteristics resulting in loss of
installed one. control.
sure, consult your BYD AUTO service station.
Using any other size or type of tire may
- 208 -
F3/F3R OWNER’S MANUAL
Never use second-hand tires on your BYD Interchanging tires When rotating tires, check for uneven wear
F3. and damage. Abnormal wear is usually
Using tires whose previous history is caused by incorrect tire pressure, improper
unknown is risk. wheel alignment, out-of-balance wheels, or
BYD AUTO recommends all four severe braking.
tires, or at least both the front or both the rear Anti-skid chain selection
tires be replaced at a time as a set. Use the tire chains of correct size.
See “If you have a flat tire” in Section 4 for tire Regulations regarding the use of tire
change procedures. chains vary according to location or type
When a tire is replaced, the wheel should of road, so always check local regulations
To equalize tire wear and help extend tire
always be balanced. before installing chains.
life, BYD AUTO recommends that you
An unbalanced wheel may affect vehicle
rotate your tires approximately every
handling and tire life. Wheels can get out of
10,000 km. However, the most appropriate
balance with regular use and should
timing for tire rotation may vary according
therefore be balanced occasionally.
to your driving habits and road surface
conditions.
- 209 -
F3/F3R OWNER’S MANUAL
Chain installation CAUTION Replacing wheels
Install the chains on the front tires as ● Do not exceed 50 km/h or the When to replace your wheels
chain manufacturer’s
tightly as possible. Do not use the tire If you have wheel damages such as
recommended speed limit,
chains on the rear tires. Retighten chains bending, cracks, or heavy corrosion, the
whichever is lower.
after driving 0.5― 1.0 km. ● Drive carefully. Avoid bumps, wheel should be replaced.
While installing chains on your tires, follow holes, and sharp turns, which may If you fail to replace a damaged wheel, the
cause the vehicle to bounce. tire may slip off the wheel or cause loss of
the instructions of the chain manufacturer
● Avoid sharp turns or lock-wheel
carefully. control.
braking as use of chains may
If wheel covers are used, they will be adversely affect vehicle handling.
scratched by the chain band, so remove the ● When driving with chains Wheel selection
covers before putting on the chains. installed, be sure to drive When replacing wheels, care should be taken
carefully. Slow down before
to ensure that the wheels are replaced by
entering curves to avoid losing
control of the vehicle. Otherwise, ones with the same load capacity, diameter,
- 210 -
F3/F3R OWNER’S MANUAL
adversely affect handling, wheel and bearing this may cause dangerous handling wheels.
life, brake cooling, speedometer/odometer characteristics resulting in loss of ● When balancing your wheels, use only
control. Otherwise, an accident may
calibration, stopping ability, headlight aim, BYD AUTO balance weight or the
occur, resulting in serious injuries or
bumper height, vehicle ground clearance, equivalent and a plastic or rubber
deaths.
and the tire or snow chain clearance to the hammer.
body and chassis. Aluminum wheel precautions ● As with any wheel, periodically check
Replacement with used wheels is not ● When installing aluminum wheels, your aluminum wheels for damage. If
recommended as they may have been check that the wheel nuts are tightened damaged, replace it immediately.
subjected to rough treatment or high mileage after driving the first 1,600 km.
and could fail without warning. In addition, ● If you have rotated, repaired, or
bent wheels which have been straightened changed your tires, check whether the
may have structural damage and therefore wheel nuts are still tight after driving
in a leaking wheel which is designed for a ● When using tire chains, be careful not to
Do not use wheels other than the ● Use only BYD AUTO wheel nuts and
manufacturer’s recommended size, as wrench designed for your aluminum
- 211 -
F3/F3R OWNER’S MANUAL
3. Electrical components
Checking battery condition…………………………………………………………………………………………………..213
Checking and replacing fuses……………………………………………………………………………………………….. 215
Refilling washer fluid ………………………………………………………………………………………………………216
Replacing light bulbs…………………………………………………………………………………………………… 217
- 212 -
F3/F3R OWNER’S MANUAL
- 213 -
F3/F3R OWNER’S MANUAL
b. If the terminal connections are loose, Check battery interior ● Do not operate the power
Check the battery interior according to the consuming devices, like the audio
tighten their clamp nuts, but do not
instructions and the indicator light of the system and illuminating system
over-tighten it.
battery. when the engine is stopped.
c. Tighten the hold-down clamp only enough
NOTICE ● Make sure the doors are closed
to keep the battery firmly in place.
and all power consuming devices,
Over-tightening may damage the battery ● Charging the battery when the cable like lights, are turned off if you are
case. is connected may seriously damage leaving your vehicle.
the electric control unit and
NOTICE
electronic devices. Before
● Be sure the engine and all connecting the battery to a charger,
CAUTION
accessories are off before disconnect the battery cable first.
If the electrolyte is not sufficient,
maintaining. please replace the battery. Don’t add
● Operating the power consuming
● When checking the battery, remove electrolyte on your own!
devices on your vehicle when the
the ground cable from the negative
engine is stopped may cause the
terminal first and reinstall it at last.
battery to be over-discharged. Then,
● Be careful not to cause a short
the vehicle may fail to start and the
circuit with tools.
battery may even be damaged
● Take care that no solution gets into
permanently.
the battery when washing it.
- 214 -
F3/F3R OWNER’S MANUAL
Checking and replacing fuses Type B Turn the ignition switch and inoperative
component off. Pull the suspected fuse
straight out and check it.
Determine which fuse may cause the
problem. The lid of the fuse box shows the
name of the circuit for each fuse. See Section
8 for the functions controlled by each circuit.
Type A fuses can be pulled out with a
Type A
pull-out-tool. For the location of the pull out
Type C
tool, refer to number 19 in the figure in
If the headlights or other electrical Section 8.
components do not work, check the fuses. If you do not ensure whether the fuse has
If any of the fuses are blown, they must be blown, try replacing the suspected fuse with
replaced. the one that you know is good.
See the “Fuse locations” part in Section 7-1
for locating the fuses. If the fuse has blown, push a new fuse
into the clip.
- 215 -
F3/F3R OWNER’S MANUAL
Only install a fuse with the amperage rating If the new fuse immediately blows out, there Refilling washer fluid
designated on the fuse box lid. is a problem with the electrical system. Have
If you do not have a spare fuse, you can pull your BYD AUTO service station correct it as
out the “DUME” fuse upon an emergency, soon as possible.
which may be dispensable for normal driving,
and use it if its amperage rating is the same. CAUTION
If you can not use one of the same amperage, Never use a fuse with a higher
use one that is lower but as close to the rating amperage rating, or any other objects
to replace the fuse. This may cause
as possible. If the amperage is lower than the
extensive damage and possibly a fire.
specified, the fuse might blow out again but
this does not indicate anything wrong. Be If any washer does not work, the washer tank
sure to get the correct fuse as soon as may be empty. Check whether the washer
possible and return the substitute to fluid level stays above the level gauge. If the
its original clip. washer fluid level goes below “LOW”, add
- 216 -
F3/F3R OWNER’S MANUAL
product is sold in BYD AUTO service station Replacing light bulbs
and many auto spare part stores. For the The following illustrations show how to take
commixture proportion with plain water, refer bulbs off. When replacing a bulb, make sure
to the manufacturer introduction. the ignition switch
After filling the washer fluid reservoir, ensure and light switch are turned off. Use bulbs with
that the funnel is put back in its original
the wattage ratings given in the table.
position.
Parking and rear position light (parking light,
NOTICE
rear turn-light, and braking light of F3R) are
Do not use engine antifreeze or any composed of a LED set. If the blown LED
Before adding washer fluid Pull out the other substitutes because it may
number does not comply with the local rules,
washer fluid funnel and hang damage you vehicle’s paint.
send your vehicle to BYD AUTO service
it on the hood support rod holder.
station for removing bulbs.
You may use plain water as washer fluid.
However, in cold areas where the
temperatures range goes below the freezing
point, use washing fluid containing antifreeze.
This type of
- 217 -
F3/F3R OWNER’S MANUAL
CAUTION drop of water on the inside of the lens, or if Rear fog light 21 W 21 W
● To prevent burns, do not replace there is water pooled inside the light, contact High brake lam p (F3) 16 W 16 W
the light bulbs while they are hot. your BYD AUTO service station. High brak e lam p
25 W 25 W
NOTICE (F3R)
● Halogen bulbs have pressurized
Lic ense plate light 5 W5W
gas inside and require special
Use a bulb of the listed type only. Door light 5 W5W
handling. They can burst or
shatter if scratched or dropped. Fron t interior ligh t 5 R5 W
Hold a bulb only by its plastic or Rear interior light 10 C10 W
metal case. Do not touch the Light bulb W Type Lu ggage
glass part of a bulb with bare
He adlight (low beam) 55 H7 com pa rtm ent light 5 W5W
hands.
He adlight (h igh beam ) 55 H1 (F3)
The inside of the lens of exterior lights such Front fog ligh t 55 H3 Lu ggage
Parki ng light (F3) 5 LED com pa rtment light 10 W 10 W
as headlights may temporarily fog up when
Front turn sig nal light 21 PY21 W (F3R)
the lens becomes wets in the rain or after Side turn signa l light 5 W Y5 W Front positi on light 5 W5 W
your car is washed. This is not a problem. Rear turn signal light Rear posit ion lig ht
21 PY21 W 0.5 LED
Fogging is caused by the temperature (F3) (F3)
Rear turn signal light Rear posit ion lig ht
difference between the outside and 4. 2 LED 1 LED
(F3R) (F3R)
inside of the lens, just like the windshield fogs
Reverse light 21 P21 W Stopl ight (F3R ) 3.4 LED
up in the rain. However, if there is a large
- 218 -
F3/F3R OWNER’S MANUAL
Items unmarked with model are Install the clip
3. Left headlight: remove the clip and If the connector is tight, wiggle it.
move the air cleaner duct. Remove
and install the clip as shown in the
following illustration.
- 219 -
F3/F3R OWNER’S MANUAL
Front fog lights (Optional)
3. Turn the bulb anticlockwise and remove 4. Install a new bulb into the mounting
it. hole by turning it clockwise.
1. Remove the bolt with a cross-head
There is no need to adjust the headlight after screwdriver and the clips.
- 220 -
F3/F3R OWNER’S MANUAL
Install the clip
- 221 -
F3/F3R OWNER’S MANUAL
6. Install new bulb 2. Turn the bulb clockwise and pull it
out, and then remove it.
Upon installing, align the circular
notching on the bulb.
Front turn signal lights To install the bulb, follow the step
opposite to the disassembling.
Side turn signal lights
- 222 -
F3/F3R OWNER’S MANUAL
Reverse lights
- 223 -
F3/F3R OWNER’S MANUAL
Rear fog lights To install the bulb, follow the step opposite to
the disassembling.
High mounted stoplight (Optional for F3)
- 224 -
F3/F3R OWNER’S MANUAL
1. Unscrew the bolts. 3. Remove the bulb
- 225 -
F3/F3R OWNER’S MANUAL
Section 8 Specifications
Service specifications………………………………………………………………………………………………………..227
- 226 -
F3/F3R OWNER’S MANUAL
Service specifications Gear oil grade for transmission: Cooling system
Lubricating the engine MT gear oil Total capability: 6.8 L
Oil grade for gasoline engine: SAE 75 W-90 Cold area (Northern),
winter Tire size: 195/60R15 88 H
SAE 5 W-30 -30°C above
SAE 80 W-90 Cold area (Northern),
SAE 15 W-40 -15°C above
summer Tire pressure: KPa (kilogram/cm )
2
- 227 -
F3/F3R OWNER’S MANUAL
- 228 -
F3/F3R OWNER’S MANUAL
(30 A)-M7.9.7.1 8. Wiper (20 A)
29. Interior lights 9. Position light (15 A)
30. NO. 2 source of Ignition switch 10. Brake lights (15 A)
- 229 -