0 evaluări0% au considerat acest document util (0 voturi)
198 vizualizări3 pagini
In the event of a customer complaint, check the affected rear lamp connector for damage. O if no problem can be found then continue with normal diagnosis. In order to install an additional ground wire, a special ground wire with splice must be prepared.
In the event of a customer complaint, check the affected rear lamp connector for damage. O if no problem can be found then continue with normal diagnosis. In order to install an additional ground wire, a special ground wire with splice must be prepared.
Drepturi de autor:
Attribution Non-Commercial (BY-NC)
Formate disponibile
Descărcați ca DOC, PDF, TXT sau citiți online pe Scribd
In the event of a customer complaint, check the affected rear lamp connector for damage. O if no problem can be found then continue with normal diagnosis. In order to install an additional ground wire, a special ground wire with splice must be prepared.
Drepturi de autor:
Attribution Non-Commercial (BY-NC)
Formate disponibile
Descărcați ca DOC, PDF, TXT sau citiți online pe Scribd
check the affected rear lamp connector for damage. o If no problem can be found then continue with normal diagnosis.
o If damage is seen follow the
procedure below.
In order to install an additional ground wire, a special ground wire with splice must be prepared.
2. Prepare wire #1:
o Cut a piece of brown wire to a length of 120 mm. o Strip the ends of the wire. o Crimp blade contact SLK 2.8 P/N 12 52 1 433 217 on one end of wire. o Crimp the flat contact for comb-type connectors P/N 61 13 1 387 144 on the other end of the wire. o Put wire #1 to one side. 3. Prepare wire #2: o Cut a piece of brown wire to a length of 120 mm. o Strip the ends of the wire. o Crimp the flat plug-in sleeve to one end of the wire P/N 07 11 9 975 531. o Crimp the flat contact for comb-type connectors on the other end of the wire P/N 61 13 1 387 144. o Put wire #2 to one side.
4. Remove the brown ground wire from the
8-pin rear lamp connector (pin 2 of X338 or Pin 3 of X339) and cut off the existing terminal.
5. Strip the end of the wire and install flat
contact (1) P/N 61 13 1 387 144. (wire #3) 6. Cut off 3 pins from the comb-type connector contact strip (1) P/N 61 13 1 387 150.
7. Connect the three ground wires to the 3-
pin contact strip (1) to create a splice.
8. Insert the 3-pin contact strip with wires
into the comb-type connector housing (1) P/N 61 13 1 393 718 and engage.
9. Fit the flat plug-in sleeve P/N 07 11 9
975 531 from wire #2 (1) onto the existing lug of the lamp holder (2).
10. Repeat steps 2-9 to prepare and install a ground splice for the remaining rear lamp.
11. For the non damaged rear lamp connector,
install the blade contact of wire #1 in accordance with the pin assignment in the 8-pin socket housing (1). Pin 2 of X338 for left rear lamp or pin 3 of X339 for right rear lamp. 12. For damaged rear lamp connector housings perform the following procedure. 13. Note the wire color(s) and pin location(s) of the wires. Refer to the vehicle ETM if necessary.
14. Remove all of the wires from the 8-pin
connector housing and inspect for damage at the terminal end. Any damaged wire(s) or corroded terminals must be repaired (See steps 15-17). 15. Cut the damaged wire(s) approximately 50 mm (Dimension A) from the terminal end and strip the end of the wire(s).
16. Cut the prefabricated repair wire P/N 12 52 0
007 171 to a length of approximately 50 mm (Dimension A) and strip the end of the wire.
17. Crimp the repair wire to the vehicle harness
using the crimp connector (1) P/N 61 13 8 353 747 and install heat shrink tubing (2) P/N 61 13 1 379 833. Make sure to slide the heat shrink tubing onto the wire before crimping.
18. Reinstall the wires in the new connector
housing P/N 12 52 7 519 956 together with ground wire #1. Use the pin locations noted down in step 13 above.
Cable Preparation Guide For Connecting MOTOTRBO Radio As A Control Station To The Radioserver (Using HLN9457 Connector and PMKN4147A Programming Cable)