Documente Academic
Documente Profesional
Documente Cultură
2 Fire Fighting
3 HVAC
4 Arena Lighting
5 Supply &Installation of M.S. cabinet for courtyard Hydrant with glass and
locking arrangement Complete including applying 2 coats of primer Paints
as per seven tank process and powder Coated finally in post office red
etc. Size: 750 x 600 x 250 mm Nos 0.00
6 Supply & Fixing bronze orifice disc for fire hydrant system and hydrants to
control the presure within 5.5 kgs / cm2 including rubber gasket packing,
bolts, nuts, washers, all complete as per direct on of the Engineer-in-charge.
Nos. 0.00
7 Supplying & Fixing 9 litres capacity and buckets with initial sand fill including
painting providing necessary brackets / clamps. proper supports as
required including provididng and fixing stands fabricated out of M.S.
section suitable for sand buckets etc. complete as directed by the
Engineer-in-charge Nos. 8.00
10 Supplying & Fixing portable fire extinguishers (ABC Type) suitable for wall
mounting including fixing the same with necessary brackets / clamps /
anchor bolts drilling holes making good the same painting the surface as
required as per direction of the Engineer-in-charge
a) 5 kg capacity- Nos. 67.00
11 Supplying & Fixing of Suitable G.M. Drain valve of 25 mm dia and G.I. Drain
pipe of required length including necessary support and painting with two
coats of enamel paint of approved colour over a priming coat etc
completion the lower end of the wet riser Nos. 1.00
12 Supplying & Fixing in position cast iron butterfly valve (AUDCO) standard
pattern (Horizontal / Vertical ) including necessary flanged joints by
providing necessary nuts, bolts gaskets, etc. all complete of the following
diameters
a) 150 mm dia Nos. 6.00
13 Supplying & Fixing heavy approved quality cast iron Wafer type non return
valves including making joints etc all complete for the following diameters
c) 80 mm dia No 1.00
15 MAIN PUMPS :
Supply , Erection & commissioning of back pull out type centrifugal pump
having cast iron casing, bronze impeller hand finished and dynamically
balanced EN 8 high tensile steel shaft running in double ball bearing Each
pump should be coupled on an MS fabricated base plate to a Suitable HP
2900 RPM, 415 Volts , 50 Cycles, AC 3 Phase TEFC motor in IP 55 Enclosure
16 Jockey Pump
Supply , Erection & commissioning of Horizontal self priming jockey pump
having cast iron casing, cast iron diffusers, bronze impellers EN 8 High tensile
steel shaft running in double ball bearing Each pump should be coupled
on an MS fabricated base plate to a suitable HP 2900 RPM, 415 Volts , 50
Cy, 3 Ph
180 LPM at 70 m head No 1.00
17 Supplying & Fixing pressure gauge, glycerin Filled with isolation valve Nos. 3.00
18 Providing & Laying 1.1 KV grade. ISI mark PVC sheathed aluminum
Conductor, armoured cables of following sizes for
a) The main pump - 3 c x 35 mm sq Rmt 35.00
OUTGOING FEEDERS :
1 No- 250 Amp MCCB with FOM
2 Nos- Contactors for Star-Delta operation
1 No- Overload Relay
1 No-On / Off button
1 No- Off Push button
1 No- On / Off Indicating Lamps
1 No- O/L Trip Lamps
1 Set – Power & Control terminals
( 2 No + 2 NC to be wired up to terminals
From Security Cabin )
1 No. 15 HP Jocky pump feeder fitted with
1 No- 63 Amp MCCB with FOM
2 No- Contactor for DOL starter.
1 No- Overload Relay
1 No- On /Off Push button
1 No- On /Off Indicating Lamps.
1 No- Trip Lamp
1 Set Power & Control terminals
1 Nos- 7.5 HP booster pump fitted wiyh:-
( As per Jocky Pump feeder )
1 No.- 63 Amp MCCB with FOM as spare
Hooter siren to be provided
Panel to be earthed.
1 Supply:
Supply of Air-cooled condensing unit complete with scroll compressor
a consist of microprocessor based control panel, initial charge of
refrigerant, vibration isolator/cushyfoot mounting etc
Supply of Double Skin Floor mounted AHU with forward curved fan
2 section with motor, coil, drive package, filter etc
(i) 11 TR Ceiling Suspended Ductable Split with min 4400 CFM Nos. 12
f ACOUSTIC INSULATION
Acoustic insulation of ducting with 12 mm resin bonded Fibre Glass
Sq.m. 1200
Crown 300 covered with RP tissue and 28G Perforated sheet.
i Drain pipe for condensate drain to the nearest drain point with 1'' PVC
pipe with vidoflex/equivalent insulation to the nearest drain as per
consultants instruction.
40 mm Rmt 80
3 MACHINE ACCESSORIES
Total load=676 TR
NATIONAL GAMES 2010 KERALA
RAJIV GANDHI INDOOR STADIUM, COCHIN
BILL OF QUANTITIES FOR ARENA FLOOD LIGHTING
Sr. Rate Amount
Item Description Unit Rate (In Words) Quantity
No. (Rs.) (Rs.)
ARENA LIGHTING
1 Supply, installation, testing and commissioning of sports flood light fixture
suitable for 2 x 400W metal halide lamps similar to Bajaj Cat Ref: BGENF 22
- 2x400MH complete with cast aluminium control gear box. Nos 112.00
A 11 KV SUBSTATION WORK
B M. V. SWITCHBOARDS
and cable end box on LV side complete with test certificates from manufacturers
and completely erected on provided plinth or on pole as per direction.The
transformer shall be tested at factory in presence of Departmental Engineer before
despatch to site.
A.3 Supplying & erecting 3 C x 150 sq.mm 11 kV, XLPE 140 Mtrs.
armoured cable on wall/ceiling or laid in provided trench /pipe / thro' ready
trench, through RCC pipes (already laid), in air, in prepared RCC trench including
supplying and providing clamps supports.
Sr. Rate in Words Total Amount
Description Quantity Unit Unit Rate Rs.
No. (Rs.) (Rs.)
A.4 Making trench 1 Mtr. Deep in any soil other than rock with sand bedding above 80 Mtrs.
and below cable, bricks on both sides & on top of cable and reinstating of cable
trench with ramming with supply of sand bricks, etc. except cable ). the rate under
this item is applicable only to cable laid underground with excavation.
A.5 Providing & laying 143/ 123 mm dia DWC Pipe for 20 Mtrs.
enclosing cable below ground/road surface, complete. (Chapter Supplying &
laying (including excavation) &
necessary back filling with light ramming to make the
road/ground surface as it was (Except bitumen carpet)..
A.6 Providing and erecting Heat shrinkable indoor termination kit for 11 kV ( E ) XLPE 5 Set
HT including Clamping / Supporting pole, termination suitable for 11 KV, 3C x 150
sq.mm. XLPE insulated and armoured cable.
A.7 Providing and erecting Heat shrinkable Out door termination kit for 11 kV ( E ) XLPE 1 Set
HT including Clamping / Supporting pole, termination suitable for 11 KV, 3C x 150
sq.mm. XLPE insulated and armoured cable.
A.8 Supplying & erecting Galvanised cast iron earth plate size 60 x 60 x 0.6 cms.buried 2 set
in specifically prepared earth pit 1.5 mtr. below ground with layers of charcoal
with 19mm. dia. G.l. pipe with funnel with a wire mesh for watering and brick
masonry block C.l. cover complete as per para 7.3 of l.S. 3043 with necessary
length of G.l. earth Strip 50 x 6 mm bolted with the plate and covered in 25 mm.
dia. G.l. pipe 2 mtr. long complete duly tested by earth tester and recording the
results.
A-9 Supplying & erecting Galvanised cast iron earth plate size 120 x 120 x 0.6 8 Sets
cms.buried in specifically prepared earth pit 1.5 mtr. below ground with layers of
charcoal & salt with 19mm. dia. G.l. pipe with funnel with a wire mesh for watering
and brick masonry block C.l. cover complete as per para 7.3 of l.S. 3043 with
necessary length of G.l. earth Strip 50 x 6 mm bolted with the plate and covered in
32 mm. dia. G.l. pipe 2 mtr. long complete duly tested by earth tester and
recording the results.
A-10 Supplying & erecting G.I.strip of any size laid underground 600 mm deep including U.R Kg
eacavation, refilling etc. or clamped with saddles / spacers on structure or on
surface, cable tray. Strip to be bolted and welded for continuity and joints to be
painted by anticorrosive paint / compound.
Sr. Rate in Words Total Amount
Description Quantity Unit Unit Rate Rs.
No. (Rs.) (Rs.)
A-11 Supplying & erecting Copper earth stripes of any size laid underground 600 mm 400 Kg
deep including eacavation, refilling etc. or clamped with saddles / spacers on
structure.or on surface, cable tray Copper Strip to be bolted and brazed for
continuity.
A.12 Supplying and erecting rolled steel joist (I-section) pole 150 x 80 mm. (14.9 U.R Nos
Kg/Meter) minimum & 11 mtr. long complete and duly painted with two coats of
red oxide paint and one coat of bituminous paint for the length to be embedded
in ground and plinth & two coats of aluminium paint for the remaining portion
above ground complete with M.S. base plate of size 30cm x 30cm x 6 mm thick
welded at the bottom complete embedded in RCC foundation.
A.13 Supplying & erecting ISMC 100 x 50 mm. with 4.7 mm thick web & 7.5 mm thick with U.R Kg
clamps, MS angle for cross arm of suitable length fabricated for high tension
insulator mounting and provided with clamps of 50mm x 6 mm. M.S. flats and 16
mm. nuts &bolts for each cross arm duly painted with one coat of red Oxide primer
and two coats of silver paint.
A-14 Supplying and erecting ACSR conductor of size 6/2.11 mm. (squirrel) complete, U.R Mtrs.
erected for over head line with stringing and binding with proper size of aluminium
conductor for binding and suitable size of P.G. clamps, jump ring Lugs, required
extra thick alkathene pipe etc. complete(weight of ACSR conduct 85 kg per 1000
m)
A-15 Supplying and erecting approved make thyrite type lightening arrester suitable for U.R Nos
11 KV supply with necessary ancillary materials and accessories complete, erected
on the cross arm provided and connected to the over-head line.
A-16 Supplying and erecting porcelain disc type insulator suitable for 11 KV line, U.R Sets
complete erected with all accessories and nuts and bolts on cross arm provided.
A-17 Supplying and erecting porcelain post type insulator suitable for 11 KV line U.R Sets
complete erected with all accesseries and nuts and bolts on cross arm provided.
Sr. Rate in Words Total Amount
Description Quantity Unit Unit Rate Rs.
No. (Rs.) (Rs.)
A-18 Supplying and erecting approved make 11 KV out door type gang operated air U.R Set
break triple pole switch, 400 amperes capacity, with 2 post pin type insulator per
phase, mounted on horizontal or vertical position on cross arm provided with
adequate length of G.l. pipe for operating handle erected on extended square
shaft. The operating handle be provided with lock and key at suitable height from
ground level with necessary clamp.
A-19 Supplying and erecting approved make 11 KV out door type drop out fuse unit U.R Set
complete with fuse holders, fuse barrel with metal fitting, fuse element mounted on
M.S. channel with working current of 50 Amps. Capacity and operating rod of
suitable length complete erected on cross arm provided.
A-20 Supplying, erecting, testing, commissioning 11 KV H.T. metering cubical (Compact 1 Nos
Type) Licensee approved fabricated with 2mm.(14 SWG) M.S.sheets with
supporting angle and channel, painted with powder coating or epoxy paint shade
light gray, copper bus bar size 25x6 mm electronic security lock and Godrej make
mechanical lock, with counter meter for measuring no of times the opening of
doors, top side cover ( C.T.P.T COVER) interlock with meter doors, epoxy coated 3
nos C.T having required ratio between 5/5A to 100/5A burden 10 VA class 0.5
I.L.12/28/75 KVP epoxy terminal block suitable for provided trivector meter, and
provision for incoming and outgoing cables etc complete duly tested by Licensee
and with necessary Test Certificates and erected on provided plinth/ C.C
foundation
Sr. Rate in Words Total Amount
Description Quantity Unit Unit Rate Rs.
No. (Rs.) (Rs.)
A.21 LIASON & CO-ORDINATION with KSEB and Electrical Inspectorate for following 1 Job
(a) Submission & Approval of Installation Drawings before start of work.
(b) Survey & approval of Installation location.
(c) Inspection and approval of the installation under scope of this tender (H.T. & L.T.)
B BUS COUPLER
1No. 800A 4P On Load Change over switch
C Busbars
800 Amps TP(N) Al. Heat Shrink colour PVC sleeved.
D OUT GOING
a 3 Nos. 400 A MCCB 50 KA with Ind Lamp & Ammeter
Sr. Unit Rate Rate in Words Total Amount
Description Quantity Unit
No. Rs. (Rs.) (Rs.)
b 3 Nos. 250 A MCCB 50 KA with Ind Lamp & Ammeter
c 1No. 63 A TP contactor with ON / OFF Indicating Lamps, Start / Stop P.B.S. and 1No. 63A TP
MCCB 50 KA, 0-60 Sec Timer and 25 KVAR APP double layer capacitor.
Sr. Unit Rate Rate in Words Total Amount
Description Quantity Unit
No. Rs. (Rs.) (Rs.)
B-2 Supply, installation, testing, commissioning of automatic power Factor correction panel
with following specification. Panel made form 14 swg CRCA sheet, Free standing, floor
mounted, front hinged, for indoor use, cubicle type, rear removable, underlined and
removable bottom gland plates for incoming connections, dust and vermin proof with
TPN Alluminium bus bar, complete with internal wiring, ferrules name plates, powder
coated, with complete interlock, gaskets, and following accessories. As Per single line
diagram. (PDB #03 Panel)
A Incomer 1 Nos
1 Nos. 250 Amps TP (N) MCCB 35 KA with 3 Nos R-Y-B LED Indicating Lamps, 3 Nos control
MCB's, 0-250 A Ammeter with Ammeter selector switch, 3 Nos 250 A/5A CL-1 15VA C.T.'s
B Busbars
250 A TPN Aluminium Heat shrink colour PVC sleeved.
C OUT GOING
a 3 Nos. 125 A MCCB 35 KA with Ind Lamp & Ammeter
Sr. Unit Rate Rate in Words Total Amount
Description Quantity Unit
No. Rs. (Rs.) (Rs.)
B-3 Supply, installation, testing, commissioning of automatic power Factor correction panel 0
with following specification. Panel made form 14 swg CRCA sheet, Free standing, floor
mounted, front hinged, for indoor use, cubicle type, rear removable, underlined and
removable bottom gland plates for incoming connections, dust and vermin proof with
TPN Alluminium bus bar, complete with internal wiring, ferrules name plates, powder
coated, with complete interlock, gaskets, and following accessories. As Per single line
diagram. (APFC Panel)
A Incomer
1 Nos. 400 Amps TP (N) MCCB 35 KA with 3 Nos R-Y-B LED Indicating Lamps, 3 Nos control
MCB's, 0-600 A Ammeter with Ammeter selector switch, 3 Nos 600 A/5A CL-1 15VA C.T.'s
and 1No 12 stage APFC relay.
B Busbars
400 A TPN Aluminium Heat shrink colour PVC sleeved.
C OUT GOING
a 1 sets each with Sets of 16A HRC fuses
- 16A TP contactor with ON-OFF P.B.'s, ON-OFF Indicating Lamps & control MCB's , - 0 -
60 Sec timer
1 No - 5 KVAR APP ( D/L ) Capacitor
f 1 sets each with Mountings as per ' e ' above EXCEPT 25 KVAR capacitor for which only
space shall be provided.
g 1 set with Provision of space only for mountings / capacitor as per '' e '' above.
Mountings & Capacitors not to be provided. However necessary knockouts for PB's etc. to
be provided.
C.3 Making trench 750 Mtr. Deep in any soil other than rock with sand bedding 700 Mtrs.
above and below cable, bricks on both TOP of cable, and reinstating of
cable trench with ramming with supply of sand bricks, etc. except cable ).
the rate under this item is applicable only to cable laid underground with
excavation.
D.15 Supply and laying 12 mm thick 1 Mtr. wide rubber matting of quality approved by
10 Mtrs.
electrical inspectorate including proper fixing on floor.
D.16 Supply and erection 6.5 Kgs. CO2 fire extinguishers including fixing brackets. 2 Sets
D.17 Supply and erection Shock treatment charts in 3 (three) languages with wooden
1 Sets
frame and glass top cover.
D.18 First Air box (Supply only) 1 Nos.
D.19 11 KV handgloves (1 Pair of 2 Nos.) supply only. 1 Pair
Total
Sr. Unit Rate Rate in
Description Quantity Unit Amount
No. Rs. Words.(Rs)
(Rs.)
D.20 Supply and erection of Hunsel Make Junction Boxes with hinged & screwed cover,
earthing stud, 4Way Connector Strip, knockouts on all sides for cable gland of 3C x
2.5 Sq.mm. YWY cables , Junction Box should bePV C poly corbonate Size Approx. 8 Nos.
150 x 150 x 50 mm]. these are cable Loop Boxes for 3C x 2.5 Sq. mm. YWY Cable, to
be laid on Trusses and tapped for High Bay Fittings.
D.21 Supplying & erecting telephone Krone connection box for 20 pair Telephone cable
2 Nos.
complete with krone connector of required size erected on wall.
D.22 Supplying, installing, testing & commissioning Digital type SIEMENS Make type EPABX
(Electronic Private Automatic Branch Exchange) of 8 x 16 extension as per 1 Nos.
specification
D.23 Supply and erection of 11 Mt. Long M.S Tubular Swaged Pole (Bajaj Type 410 SP 49)
with 300 x 300 x 10 mm M.S. Base Plate welded, an in built Cable Box having hinged
cover gaskat and panel locking arrangement, consisting of 4 way Connector Strip
& S.P. MCB, 2 Nos. Sleeves welded to pole for cable entries. The pole should be
installed in ground with 450 x 450 x 1800 mm 1:3:6 Cement concrete foundation, 5 Nos.
Coping 450 x 450 x 500 mm size (above grouted level) including necessary
excavation, reinstatement, painting with 2 coats of Red Oxide and 2 coats of
Aluminium Paint. The pole should have bent top portion, to support a street Light
Fitting. Poles for Single Street Light.
D.24 Supplying & and laying (including excavation ) 90 mm outside dia double wall
corrugated pipes (DWC) of HDPE with IS 14930 Part II mark on it for cable laid under
ground with necessary connecting sockets / coupleings, tees of same materials
and at required depth up to 90 CM. below road / ground surface, back filling with 20 Mtrs.
light ramming to make the road / ground surface as it was ( except bitumen carpet
)
D.25 Supply installation of gen -2 Building Lightning arrester with details as per the
requirement. Complete with Protector, down conductors, Gun Metal Tape
Clip,Mechanical counter, Stainless Steel Mast, (INGESCO Make PDC 3.1 / DMSGI 1 Nos.
Make /Indelect, France )
E.3 Point wiring for Plug, with ISI mark 2-1.0 sq.mm 1.1 KV grade PVC insulated
copper wire with 2.5 Sq.mm ISI mark PVC insulated copper wire in green color
used for earthing in existing Casing capping/ PVC conduit on the light or fan
board for plug complete with 3 pin 6A modular type socket and 6 Amp modular 38 Pnts.
type Switch erected on original sheet metal / non metallic un-breakable box of
light or fan board flush on wall with double (mounting & cover) Modular plate.
E.4 Point wiring for Power Plug, on board with ISI mark 2-4 sq.mm 1.1 KV grade PVC
insulated copper wire with 2.5 Sq.mm ISI mark PVC insulated copper wire in
green color used for earthing in existing casing capping/ rigid PVC conduit on
board for plug complete with 6 pin 6A & 16 A modular type socket and 16 Amp 130 Nos
modular type Switch erected on original sheet metal / non metallic un-
breakable box flush on wall with double (mounting & cover) Modular plate.
E.5 Point wiring for Telephone concealed type with 2 pair telephone cable in
existing concealed rigid PVC conduit on the light or fan board for plug
complete erected on original sheet metal / non metallic un-breakable box of 28 Nos
light or fan board flush on wall with double ( mounting & cover )Modular plate.
(Only Point)
Unit Rate Rate in Total Amount
Sr. No. Description Quantity Unit
Rs. Words.(Rs) (Rs.)
E.6 Supplying and erecting 2 Module electronic type 100 Watts Fan step Regulator /
24 Nos
speed controller complete erected on provided switchboard.
E.7 Supplying and erecting Computer point of networking with face plate, Box, I/O
jack, RJ–45 pin complete erected on wall/table /partisan complete with testing. 28 Nos
E.8 ( Specification as Item E-1) but Point Wiring on above faulse ceilling and
concealed in Wall, Panels, etc with 25mm H.G. PVC Conduit, accessories like
Junction Boxes, Couplers, spacers, Saddles etc. using 3 x 1.5 Sq.mm. [P, N, E]
Multistranded Copper Conductor, FRLS PVC inculated, 1100 V grade, Color 40 Pnts.
Coded, ISI marked wires, Modular Version Switch Accessories Plates, Switches,
Sockets etc. Point from Switch Board to 3 Plate ceiling rose / holder. Two Light
Points controlled by one 6 A S.P. Switch.
E.9 Supplying and erecting 16 / 20 / 25 A starter (modular range) 2
module for AC unit on provided box complete & duly concealed 24 Nos
with necessary material and connected.
E.10 Supplying and erecting modular type switch 6A / 10A ISI mark
approved make duly erected on provided plate and box with wiring 5 Pnts.
connections complete.
E.11 Supplying and erecting modular type 3 pin 6 A socket ISI mark
approved make duly erected on provided plate and box with wiring 5 Pnts.
connections complete.
E.12 Supplying and erecting modular type 3 pin 6 / 16 A combined
unit ISI mark approved make duly erected on provided plate and 5 Nos
box with wiring connections complete.
E.13 Supplying and erecting modular type switch one way 16 / 20 A,
ISI mark, approved make duly erected on provided plate and box 5 Nos
with wiring connections complete with neon indicator.
E.14 Supplying and erecting PVC Surface modular switch box with
double mounting plate for 3 module duly erected in an 10 Pnts.
approved manner.
Unit Rate Rate in Total Amount
Sr. No. Description Quantity Unit
Rs. Words.(Rs) (Rs.)
E.15 Supplying and laying PVC casing-n-capping) of size 25 mm. with accessories on
100 Mtrs.
wall/ceiling
E.16 Supplying and erecting of MMS PVC conduit, with accessories as Junction Boxes,
Couplers, Spacers, Saddles etc. concealed above false ceiling, Wall, panels
etc. for following.
a) light board Submains
b) 3P 6A Socket Switch computer Points
c) 3P 6 / 16A Socket Switch Point
d) Cat -6 Cable Point
e) Telephone Cable Point. Etc.
E.16.1 32 mm H.G. Midium Gauge PVC conduit, 100
E.16.2 25 mm H.G. Midium Gauge PVC conduit, 600
E.16.3 20 mm H.G. Midium Gauge PVC conduit, 200 Mtrs.
E.17 Supplying and erecting Multistranded Copper Conductor FRLS PVC insulated,
Color Coded, 1100 V grade, ISI marked wires, to be laid in item above
E.17.1 2 x 1.5 Sq.mm. [P, N] Wires. 50 Mtrs.
E.17.2 2 x 2.5 Sq.mm. [P, N] Wires. 400 Mtrs.
E.17.3 2 x 4 Sq. mm. [P, N] Wires. 750 Mtrs.
E.17.4 2 x 6 Sq. mm. [P, N] Wires. 100 Mtrs.
E.17.5 4 x 4 Sq.mm. [3 P, N] wire 50 Mtrs.
E.17.6 4 x 6 Sq.mm. [3 P, N] wire 25 Mtrs.
E.17.7 4 x 2.5 Sq.mm. [3 P, N] wire 50 Mtrs.
E.17.8 1 X 2 mm Bare Copper Earth Wire of 14 SWG. 800 Mtrs.
E.17.9 1 X 2.6 mm Bare Copper Earth Wire of 12 SWG. 100 Mtrs.
E.17.10 1 X 3.15 mm Bare Copper Earth Wire of 10 SWG. 100 Mtrs.
E.17.11 1 X 4 mm Bare Copper Earth Wire of 8 SWG. 100 Mtrs.
Unit Rate Rate in Total Amount
Sr. No. Description Quantity Unit
Rs. Words.(Rs) (Rs.)
E-18 Supplying & erecting RG-59 TV Co-axial cable in already provided PVC conduit
U.R Mtrs.
pipe / in place and concealed in wall.
E.19 Supplying & erecting Telephone wire in already provided PVC conduit pipe in
place and concealed in wall.
E.19.1 Telephone wire 2 Pair & 0.6 mm 200
E.19.2 Telephone wire 4 Pair & 0.6 mm 300
E.19.3 Telephone wire 5 Pair & 0.6 mm 100
E.20 Supplying & erecting CAT - 6 cable in already provided PVC conduit pipe in
600 Mtrs.
place and concealed in wall..
E.21 Supplying, installation, testing and commissioning of Digital inverter of reputated
make 800 VA single phase 230 volt complete with over load relay and necessary
protections, with battery of 12 volt –150 AH Excide make maintenance free
(Three Hour Back-Up), with battery terminals wire and necessary copper wire, 1 Sets
with plug and socket top connected to load up to 750 watt with required
accessories.
The rate quoted shall include all above and testing, commissioning of Fitting.
F.1 Supplying and erecting luminous type call bell indicator with plastic body, heavy duty
coil and indicator lamp working on 230 V. A. C. supply with resetting arrangement 24 Each
complete erected on double wooden/sunmica board.
F.2 Supply & Erection of 4 x 54 T-5 Tube, high Bay Fittings with tube to be installed on Trusses,
at a height of 9 to 7 Mtrs.( Similar to Ge EIFFEL 4X54) [Contractor should make an 8 Nos.
arrangement of scaffoldings].
F.3 Supplying & erecting 1x28 Watt T-5 Energy Efficient Retrofit/stand alone Fluorescent Tube
light fitting (EETLF) box type complete with Electronic Ballast and lamp holders duly wired
ready to use for 230 Volts. 50 Hz. Single phase AC supply to IS:10322 as per quality
requirement and erected on varnished wooden blocks with flexible wire twin core 24/0.2 142 Each
mm & without T-5 Energy Efficient Tubular Fluorescent Lamp. (Similar To Philips TMS 122 /
128 EHF)
F.4 Supplying & erecting 2x28 Watt T-5 Energy Efficient Retrofit/stand alone Fluorescent Tube
light fitting (EETLF) box type complete with Electronic Ballast and lamp holders duly wired
ready to use for 230 Volts. 50 Hz. Single phase AC supply to IS:10322 as per quality
requirement and erected on varnished wooden blocks with flexible wire twin core 24/0.2 16 Each
mm & without T-5 Energy Efficient Tubular Fluorescent Lamp .(Similar To Philips TMS 122 /
228 EHF)
F.5 Supplying & erecting T 5 28 W Energy efficient fluorescent tube 174 Each
F.6 Supplying and erecting approved make recessed down lighter with mirror optics suitable
for 2 x 18 W compact flou. lamp fixed in false ceiling. (Similar To Philips FBH 150 /218) 4 Each
Sr. Unit Rate Rate in Total
Description Quantity Unit
No. Rs. Words.(Rs) Amount Rs.
F.7 Supplying and erecting approved make recessed down lighter with mirror optics suitable
for 1 x 18 W compact flou. Lamp, fixed in false ceiling (Similar To Philips FBH 150 /118) 4 Each
F.8 Supplying and erecting circular type Celling lighter suitable for CFL 2 x 18 watts including
2 Nos.
gear box, fixed in ceiling. Decorative type (Similar To Philips WW BCS 1901
F.9 Supplying and erecting luminaries suitable for 11 watt CFL lamp,fixed on wall above
6 Nos.
mirror (Similar To Philips FMS200/111)
F.10 Supplying & erecting compact fluo.lamp 11 W, 230 V, to be used with provided ballast
6 Nos.
F.11 Supplying & erecting compact fluo.lamp18 W, 230, V to be used with provided ballast
42 Nos.
F.12 Supply & Erection of 250W M.H. Street Light Fittings with Lamp to be mounted on 11 Mtr.
High Street light Pole, at mounting height of about 9 Mtrs. (Similar To Philips SGP 325) 5 Nos.
F.13 Supplying & erecting gate light fitting with 300 mm. dia.clear acrylic bowl / mushroom /
round shape with bollard suitable for 2 X 18 watt CFL lamp on provided pipe (Similar 2 Nos.
ToCromption CFPT 18)
F.14 Supplying & erecting 4 x 14 Watt Mirror optic fitting, false Ceiling mounted with 14 watt 4
1 Nos.
Nos tube lights. GE TC 4X24 MO MLC R 300 HF
F.15 Supplying & erecting 150 W M.H. Flood Light Fittings with lamp to be mounted on Pole
4 Nos.
1.5 Mtr. Hight G.I Pipe Pole,for building illuminiation.( Bajaj)
F.16 Supplying & erecting Bollard Path Lights [0.9 M Ht] with 18-W CFL .( Similar to Ge ELVIS 3
10 Nos.
FT)
F.17 Supplying & erecting ceiling fan of 1200 mm sweep complete erected in position. 24 Each
F.18 Supplying and erecting Exhaust fan medium duty 230 V. A. C. 50 cycles 225 mm. 1400
RPM condensor complete erected in position with necessary materials. Fan motor with 32 Each
moisture proof treatment and ‘E’ class insulation.
F.19 Supplying and erecting Exhaust fan heavy duty 230 V A.C. 50 cycles 375 mm. 900 RPM
1 Each
complete erected in position
TOTAL SUPPLY & ERECTION SECTION - ' F '
(CARRIED FORWARD TO SUMMARY SHEET SECTION ' G ')
CONNECTED LOAD DETAILS AND MAX DEMAND CALCULATIONS OF RAJIV GANDHI
INDOOR HALL KOCHI, KERALA.
6 Room Light, Computer, Street Light & Garden 20.00 0.80 16.00
Lights
7 Equipment Load of Coart 10.00 0.80 8.00
Cable From To Load in Size NoX Core X Sqmm x Type Approx. Termination
No Kw Total Qty in
Meter
C-1 KSEB Supply point Metering Kiosk 500 KVA 1 x 3 C X 150 Sq. mm. 11 KV XLPE 100 O/D - 1, I/D-1
C-2 Metering Kiosk H.T.Panel 500 KVA 1 x 3 C X 150 Sq. mm. 11 KV XLPE 20 I/D-2
C-3 H.T.Panel Transformer (500 KVA) 500 KVA 1 x 3 C X 150 Sq. mm. 11 KV XLPE 20 I/D-2
140 O/ D - 1, I/D-5
C-6 MDB PDB # 01 ( Arena Light) 163 2 X 3.5 C X 150 Sq. mm. A Y F Y PVC 100 4
C-7 MDB PDB # 02 ( Air 90 1 X 3.5 C X 150 Sq. mm. A Y F Y PVC 100 4
ventelatation plant)
100 4
C-8 MDB PDB # 03 77 1 X 3.5 C X 95 Sq. mm. A Y F Y PVC 25 2
50 4
Cable From To Load in Size NoX Core X Sqmm x Type Approx. Termination
No Kw Total Qty in
Meter
C-10 PDB # 03 PDB # 03 Fire Fightning 38 1 X 3.5 C X 50 Sq. mm. A Y F Y PVC 60 2
90 4
C-12 PDB # 06 MLDB 20 1 X 4 C X 25 Sq. mm. A Y F Y PVC 20 2
40 4
225 18
C-23 MLDB LDB # 05 2 1 X 4 C X 10 Sq. mm. A Y F Y PVC 15 2
Cable From To Load in Size NoX Core X Sqmm x Type Approx. Termination
No Kw Total Qty in
Meter
C-24 LDB # 05 Street light pole 1 1 X 4 C X 10 Sq. mm. A Y F Y PVC 150 10
265 20
C-31 PSDB # 0601 Water Pump Panel 5.5 1 X 4 C X 4 Sq. mm.Y W Y(Copper) 50 2
C-32 PSDB # 060101 1phase & 3 Phase 1 X 4 C X 4 Sq. mm.Y W Y(Copper) 100 2
Sockets
305 14
C-33 MDB Garden Water pump 3.75 1 X 4 C X 2.5 Sq. mm.Y W Y(Copper) 40 2
panel
C-34 LDB # O1 Garden Lights 1.5 1 X 4 C X 2.5 Sq. mm.Y W Y (Copper) 100 10
155 14
C-36 LDB # O6 Gallary High Bay fitting 1 X 3 C X 2.5 Sq. mm.Y W Y(Copper) 150 8
Cable From To Load in Size NoX Core X Sqmm x Type Approx. Termination
No Kw Total Qty in
Meter
150 8
C-37 Ex. EPABX Telephone Crone 20 pair 0.5 mm Armoured Telephone cable 100 0
Junction Box 100
CABLE SCHEDULE ( SUMMARY) OF RAJIV GANDHI INDOOR HALL KOCHI KERALA.
A SUBSTATION
ITEM No B.3
SR DESCRIPTION Unit Qty RATE Rs AMOUNT Rs
1 400 A MCCB 35 KA Nos 1
2 LED R-Y-B Indicating Lamps. Nos 25
3 Control MCB's 2 A Nos 25
4 800 / 5A 15 VA class 1 C.T.'s Nos 3
5 12 stage APFC relay. Nos 1
6 Line voltage With Selector Nos 1
7 Line Current With Selector No 1
400 Amps TP(N) Al. Heat Shrink colour PVC
8 Kg 100
sleeved.
9 16 A HRC fuses Nos 3
10 32 A HRC fuses Nos 6
11 40 A HRC fuses Nos 6
12 63 A HRC fuses Nos 18
13 16 A TP contactor Nos 1
14 32 A TP contactor nos 2
15 40 A TP contactor nos 2
16 63 A TP contactor Nos 6
17 Start / Stop P.B.S Nos 11
18 0-60 Sec Timer Nos 11
19 APP double layer capacitor. KVAR 175
20 CRCA Sheet kg 300
21 Powder coating Kg 300
22 Fibriction kg 300
23 Wire, Hardware, slives Bus supports Lugs etc. Ls 1
24 Labour charges ls 1
ITEM No D.13
SR DESCRIPTION Unit Qty RATE Rs AMOUNT Rs
a. 30A TPE metal clad socket with chain, top
1 Nos 1
cover and plug top - 1 Set
2 b. 20A 2 Pin and earth as above. - 1 Set. Nos 1
3 c. 32A TPN MCB - 10KA - 1 No. Nos 1
4 d. 20A SPN MCB - 10 KA - 1 No. Nos 1
5 CRCA Sheet kg 10
6 Powder coating Kg 10
7 Fibriction kg 10
8 Wire, Hardware, slives Bus supports Lugs etc. Ls 1
9 Labour charges ls 1