Documente Academic
Documente Profesional
Documente Cultură
The technical data in this document (or file) may contain US data and be controlled for export under the Export
Administration Regulations (EAR), 15 CFR Parts 730-774, ECCN: 9E991. Violations of these laws may be
subject to fines and penalties under the Export Administration Act.
The content of this document is the property of and contains information proprietary to MESSIER-BUGATTI and/or
GOODRICH, and recipient by accepting this document agrees to this.
It must not be used for any purpose other than that for which it is supplied nor may information contained in it be divulged or
reproduced in whole or in part without MESSIER-BUGATTI and/or GOODRICH prior written consent, except for internal
use and, in this case, all information reproduced must be protected by the MESSIER-BUGATTI and/or GOODRICH
proprietary legend.
Copyright © 1996
TP2
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TRANSMITTAL SHEET
TO: HOLDERS OF COMPONENT MAINTENANCE MANUAL FOR MAIN LANDING GEAR CARBON
BRAKE ASSEMBLY ATA 32-41-81
Revision No. 5, dated Apr 26/11 is attached and covers all components held by every operator.
CAUTION: THIS MANUAL SUPERSEDES THE PREVIOUS ISSUE: ALL THE PAGES OF THE
PREVIOUS ISSUE MUST BE REMOVED, DESTROYED AND REPLACED BY ALL THE
PAGES OF THE NEW REVISION. THIS IS NECESSARY TO TAKE INTO ACCOUNT
THE TRANSFERRED PAGES WHICH ARE NOT COVERED BY A TECHNICAL
MODIFICATION.
Refer to the HIGHLIGHTS section for the list of the pages which are covered by a technical modification.
New logo added.
FILING INSTRUCTIONS:
Remove and destroy all the pages of the previous issue. Replace them by all the pages of the Revision
No. 5, dated Apr 26/11.
TL
Page 1
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TL
Page 2
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
HIGHLIGHTS
Pages which have been added, revised or deleted are outlined below together with the Highlights of the
Revision.
INTRODUCTION R
TASK 32-41-81-871-801-A01 R
TASK 32-41-81-870-801-A01 R
SUBTASK 32-41-81-700-001-A01 R
SUBTASK 32-41-81-700-002-A01 R
SUBTASK 32-41-81-710-001-A01 R
SUBTASK 32-41-81-790-001-A01 R
HLTS
Page 1
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-780-001-A01 R
SUBTASK 32-41-81-700-003-A01 R
SUBTASK 32-41-81-750-001-A01 R
SUBTASK 32-41-81-700-004-A01 R
TASK 32-41-81-800-001-A01 R
SUBTASK 32-41-81-810-001-A01 R
DISASSEMBLY R
TASK 32-41-81-000-801-A01 R
SUBTASK 32-41-81-000-002-A01 R
SUBTASK 32-41-81-010-001-A01 R
SUBTASK 32-41-81-010-002-A01 R
SUBTASK 32-41-81-010-003-A01 R
SUBTASK 32-41-81-040-001-A01 R
SUBTASK 32-41-81-040-002-A01 R
SUBTASK 32-41-81-040-003-A01 R
CLEANING R
SUBTASK 32-41-81-100-001-A01 R
SUBTASK 32-41-81-110-002-A01 R
HLTS
Page 2
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
INSPECTION/CHECK R
SUBTASK 32-41-81-200-001-A01 R
HLTS
Page 3
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-200-007-A01 R
SUBTASK 32-41-81-200-008-A01 R
SUBTASK 32-41-81-200-010-A01 R
REPAIR R
SUBTASK 32-41-81-320-001-A01 R
SUBTASK 32-41-81-350-001-A01 R
SUBTASK 32-41-81-300-001-A01 R
REPAIR 1 R
SUBTASK 32-41-81-010-005-A01 R
HLTS
Page 4
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-010-006-A01 R
REPAIR 2 R
TASK 32-41-81-300-803-A01 R
SUBTASK 32-41-81-010-007-A01 R
SUBTASK 32-41-81-440-001-A01 R
SUBTASK 32-41-81-410-003-A01 R
REPAIR 3 R
TASK 32-41-81-300-804-A01 R
SUBTASK 32-41-81-320-004-A01 R
SUBTASK 32-41-81-320-005-A01 R
REPAIR 4 R
TASK 32-41-81-300-805-A01 R
SUBTASK 32-41-81-320-006-A01 R
REPAIR 5 R
HLTS
Page 5
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-300-002-A01 R
REPAIR 6 R
SUBTASK 32-41-81-320-012-A01 R
SUBTASK 32-41-81-320-013-A010 R
REPAIR 7 R
TASK 32-41-81-300-808-A01 R
SUBTASK 32-41-81-320-014-A01 R
REPAIR 8 R
HLTS
Page 6
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-380-005-A01 R
ASSEMBLY R
HLTS
Page 7
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-440-004-A01 R
SUBTASK 32-41-81-440-005-A02 R
SUBTASK 32-41-81-410-005-A01 R
SUBTASK 32-41-81-400-002-A01 R
TASK 32-41-81-820-801-A01 R
TASK 32-41-81-820-802-A01 R
HLTS
Page 8
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TASK 32-41-81-940-802-A01 R
TASK 32-41-81-550-801-A01 R
HLTS
Page 9
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
HLTS
Page 10
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
RECORD OF REVISIONS
INSERTED INSERTED
REV. ISSUE REV. ISSUE
No. DATE DATE BY No. DATE DATE BY
1 Mar 31/99
2 Aug 30/03
3 Sep 15/08
4 Oct 12/09
5 Apr 26/11
ROR
Page 1
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
ROR
Page 2
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Keep this record in the first pages of the manual. When you get a temporary revision, put the yellow revision
pages into the manual opposite the pages changed by this revision. Write the revision number, the date at
which you put the revision into the manual and your initials. Do not remove the yellow pages until you get
a permanent revision which contains these data.
INSERTED REMOVED
TEMP REV. ISSUE PAGE No.
No. DATE DATE BY DATE BY
RTR
Page 1
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
RTR
Page 2
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
The Service Letters (SL) are usually released to give general data. But some Service Letters can contain more
data on procedures or modifications given to the component operator.
1701 Jul 31/96 EDL® Return Policy for heat sink Repair
(MESSIER-BFGoodrich S.A. FRANCE).
1685 Jul 31/96 EDL® Return Policy for heat sink Repair
(BFGoodrich-MESSIER INC. U.S.A.).
1685 Aug 30/03 EDL® Return Policy for heat sink Repair
(Goodrich-Messier INC.).
SBL
Page 1
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SBL
Page 2
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SBL
Page 3
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SBL
Page 4
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
LEP
Page 1
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
LEP
Page 2
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
LEP
Page 3
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
IPL INTRO
VENDOR LIST
10005 N Apr 26/11
10006 Blank
ALPHA/NUMERIC INDEX
LEP
Page 4
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TABLE OF CONTENTS
PAGE
INTRODUCTION .................................................................................................................. INTRO 1
1. Introduction ................................................................................................................... INTRO 1
A. Layout .................................................................................................................... INTRO 1
B. General ................................................................................................................. INTRO 1
C. Publications ........................................................................................................... INTRO 3
D. Explanation of CAUTION and WARNING statements ........................................... INTRO 3
E. WARNING and DANGER statements that apply to specific parts of the manual .. INTRO 3
DESCRIPTION AND OPERATION ....................................................................................... 1
1. Description and Operation ............................................................................................ 1
A. General ................................................................................................................. 1
B. Data ....................................................................................................................... 1
C. Description ............................................................................................................ 1
D. Operation .............................................................................................................. 13
TESTING AND FAULT ISOLATION ...................................................................................... 1001
1. Testing .......................................................................................................................... 1001
A. Reason for the job ................................................................................................. 1001
B. Job set-up information ........................................................................................... 1001
C. Job set-up ............................................................................................................. 1002
D. Procedure .............................................................................................................. 1002
(1) Initial steps .................................................................................................... 1002
(2) Measurement of the remaining length of the wear indicator pin (1-265) ....... 1003
(3) Flush and bleed procedures of the carbon brake .......................................... 1005
(4) Leakage test of the carbon brake .................................................................. 1005
(5) Low pressure leakage test of the carbon brake ............................................. 1006
(6) Operation tests of the carbon brake .............................................................. 1006
(7) Ground continuity test .................................................................................... 1009
(8) Last steps ...................................................................................................... 1009
2. Fault Isolation ................................................................................................................ 1010
A. Reason for the job ................................................................................................. 1010
B. Job set-up information ........................................................................................... 1010
C. Job set-up ............................................................................................................. 1010
D. Procedure .............................................................................................................. 1011
(1) Fault isolation of the carbon brake ................................................................. 1011
TOC
Page 1
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(5) Removal of the housing and adjuster piston assembly (1-010) from the
torque plate assembly (1-420) / heat sink (1-335) ......................................... 3006
(6) Removal of the heat sink ............................................................................... 3007
(7) Disassembly of the torque plate assembly .................................................... 3009
(8) Disassembly of the housing and adjuster piston assembly (1-010) .............. 3010
(9) Disassembly of the adjuster assembly (1-055) .............................................. 3012
CLEANING ........................................................................................................................... 4001
1. Cleaning ........................................................................................................................ 4001
A. Reason for the job ................................................................................................. 4001
B. Job set-up information ........................................................................................... 4001
C. Job set-up ............................................................................................................. 4002
D. Procedure .............................................................................................................. 4003
(1) Cleaning of the heat sink ............................................................................... 4003
(2) Cleaning of the temperature sensor .............................................................. 4006
(3) Cleaning of other parts .................................................................................. 4006
2. Paint removal from Piston Housing ............................................................................... 4007
A. Reason for the job ................................................................................................. 4007
B. Job set-up information ........................................................................................... 4007
C. Job set-up ............................................................................................................. 4007
D. Procedure .............................................................................................................. 4008
(1) Initial steps .................................................................................................... 4008
(2) Chemical procedure ...................................................................................... 4008
(3) Abrasive procedure ....................................................................................... 4009
3. Paint removal from the Torque Plate (1-425) ................................................................ 4010
A. Reason for the job ................................................................................................. 4010
B. Job set-up information ........................................................................................... 4010
C. Job set-up ............................................................................................................. 4010
D. Procedure .............................................................................................................. 4010
(1) Sand blast procedure .................................................................................... 4010
INSPECTION/CHECK .......................................................................................................... 5001
1. Inspection / Check ........................................................................................................ 5001
A. Reason for the job ................................................................................................. 5001
B. Job set-up information ........................................................................................... 5001
C. Job set-up ............................................................................................................. 5001
D. Procedure .............................................................................................................. 5002
(1) General .......................................................................................................... 5002
(2) Piston housing (1-020) .................................................................................. 5004
(3) Torque pin ...................................................................................................... 5008
(4) Torque plate assembly (1-420) ...................................................................... 5008
(5) Adjuster assembly (1-055) ............................................................................. 5011
(6) Bolts (1-465) .................................................................................................. 5014
(7) Heat shield assembly (1-415) ........................................................................ 5014
(8) Temperature sensor assembly (1-250) .......................................................... 5014
(9) Heat sink (1-335) ........................................................................................... 5015
(10) Cable guide (1-275) ....................................................................................... 5021
REPAIR ................................................................................................................................. 6001
TOC
Page 2
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TOC
Page 3
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TOC
Page 5
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TOC
Page 6
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
LIST OF ILLUSTRATIONS
LOI
Page 1
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
LOI
Page 2
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
INTRODUCTION
TASK 32-41-81-871-801-A01
1. Introduction
A. Layout
(1) This manual gives the function of parts and gives maintenance information that is required
for full shop repair .
B. General
(1) The methods and procedures in this manual are intended to promote an effective
maintenance program. Deviations from the methods and procedures are acceptable if an
equally effective method is utilized, with full recognition of airworthiness requirements.
Maintenance practices must be consistent with standard shop procedures and shall not
jeopardize the performance of the brake assembly.
(2) Refer to the Table of Contents for the page location of sections or subsections.
(3) An explanation of the use of the Illustrated Parts List (IPL) section is provided in the
Introduction of that section.
(4) The Maintenance Task Oriented Support System (MTOSS) is used in this manual for task
and subtask identification. The maintenance tasks and other data have special MTOSS
numbers for the use of Electronic Data Processing (EDP). The user of the manual can
ignore the MTOSS numbers.
(5) The manual has been verified by simulation and will be revised as necessary to give current
data.
(6) Weights and measurements in the manual are in S.I. (International System of Units) metric
units that are followed by U.S. (English) units in parentheses. English units have a period for
the decimal point. Metric units have a comma for the decimal point. Large numbers with
five or more digits to the left of the decimal point have a space (not a comma) between the
"thousands" and "hundred" digits to prevent confusion with metric decimal points. Common
conversions and abbreviations are shown in the table that follows:
INTRO
Page 1
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(7) Federal and MIL Specifications referred to in this manual can be ordered from:
DAPS
ASSIST
BLDG 4/D
700 ROBBINS AVENUE
PHILADELPHIA, PENNSYLVANIA 19111
U.S.A.
TEL: +1 (215) 697-6257
INTERNET: http://assist.dla.mil/online/start/
INTRO
Page 2
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
C. Publications
(1) This manual and its subsequent issues are available from the technical publication web
sites as follows:
(2) This manual and its subsequent issues are shown in the Messier-Goodrich S.A. or
Goodrich-Messier Inc. INDEX OF PUBLICATIONS CR47449.
WARNING : THE USE OF REPLACEMENT PARTS THAT ARE NOT SPECIALLY APPROVED
BY MESSIER-GOODRICH S.A. OR GOODRICH-MESSIER INC., OR IGNORING
OF TORQUE LIMITS AND OTHER SPECIFIC VALUES GIVEN BY THIS
MANUAL, CAN CAUSE PROPERTY DAMAGE, PERSONAL INJURY, OR
DEATH. USE ONLY MESSIER-GOODRICH S.A. OR GOODRICH-MESSIER INC.
APPROVED REPLACEMENT PARTS GIVEN IN THE ILLUSTRATED PARTS
LIST OF THIS MANUAL.
E. WARNING and DANGER statements that apply to specific parts of the manual
(1) Cadmium
(a) Obey the warnings below before you touch or do maintenance on parts that are cadmium
plated. Refer to the ILLUSTRATED PARTS LIST to identify the parts that can be
cadmium plated. The Occupational. Safety, and Health Administration (OSHA) sets
mandatory limits on exposure to cadmium dust (29 CFR 1910.1027).
INTRO
Page 3
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(b) The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN
CAUSE LUNG AND KIDNEY DISEASE.
INTRO
Page 4
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TASK 32-41-81-870-801-A01
1. Description and Operation
A. General
(1) The carbon brake is installed on the left or right axles of the landing gear.
(2) The ”NORMAL” or ”EMERGENCY” supply is connected to one of the two hydraulic fitting
assemblies on the piston housing.
(3) Friction between the stator disks (attached to the brake) and the rotor disks (which turn
with the wheel) causes the brake to operate.
(4) The input of hydraulic fluid pressure into a set of seven pistons compresses the stator disks
and the rotor disks together and thus causes the friction.
(5) The brake torque rod transfers braking torque from the torque pin to the landing gear.
(6) The temperature sensor installed through the piston housing and into a torque lug of
the torque plate, is the sensing element of the monitoring system for the carbon brake
temperature. The temperature sensor supplies an electrical resistance which changes
with the heat released on brake application.
B. Data
(1) Characteristics of the carbon brake
– Weight: 126,6 kg (279.1 lb).
– Fluid used: Hydraulic fluid as per NSA 307110 type IV.
– Maximum brake pressure: 175 bar (2540 psi).
– Running clearance: 1,5 mm (0.059 in) minimum.
– Number of pistons: fourteen.
– ”NORMAL” system: seven.
– ”EMERGENCY” system: seven.
C. Description
(1) General
(Ref. Fig. 1)
(a) The carbon brake assembly is made of three primary parts:
– The piston housing assembly.
– The torque plate assembly.
– The heat sink.
Page 1
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(b) Fourteen bolts and fourteen washers attach the complete piston housing to the torque
plate assembly with the heat sink.
(c) The carbon brake has a temperature sensor installed through the piston housing and into
a torque lug on the torque plate.
Page 2
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
General view
FIGURE 1/GRAPHIC32-41-81-991-001-A01
Page 3
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(a) The piston housing assembly has fourteen adjuster assemblies, two hydraulic fitting
assemblies, two valves and two lubrication fittings (four lubrication fittings after
accomplishment of SB 2-1577-32-4). The lubrication fittings lubricate the bearing
surfaces of the axle and the torque pin.
(b) The piston housing assembly, made of aluminum alloy has two systems which operate
independently (“NORMAL” and “EMERGENCY” systems).
– Each system has a self-sealing hydraulic fitting assembly and a valve. ((Ref. Fig. 1
and , Ref. Fig. 2), Detail 1).
– Each system is connected to seven piston cavities.
– Each piston cavity contains an adjuster assembly.
(c) For each brake unit, the main hydraulic system used can be different. It depends on
the aircraft position of the wheel in which the brake unit is mounted. (Ref. Fig. 2 and
, Ref. Fig. 3):
– Main hydraulic circuit input for wheel positions: 1, 3, 5 and 7.
– Main hydraulic circuit input for wheel positions: 2, 4, 6 and 8.
– For assisting in service difficulty, the pistons are conventionally numbered ((Ref. Fig. 2)
Detail 2).
(d) The piston housing assembly also has a torque pin which prevents movement of the
brake assembly on the landing gear.
(e) Each adjuster assembly is made of ((Ref. Fig. 3), Detail A):
– A piston sleeve.
– A piston.
– A scraper ring.
– An insulator assembly which slows the transfer of heat from the heat sink to the piston
and piston housing assembly.
– A spring which is compressed between a spring guide and the bottom of the piston.
The spring holds the guide against the retaining ring installed in the piston.
– An adjuster tube which goes through the spring guide.
– An adjuster pin with an attached ball which holds this tube against the spring guide.
– A pin retainer which holds the adjuster pin at one end of the piston sleeve.
– Seals and back-up rings which provide internal and external sealing efficiency.
Page 4
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 5
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(a) The torque plate made up of steel is cylindrical and has a flange at one of its ends.
Eighteen splines, which are at an equal distance from one another, are machined on
its outer surface. These splines engage the pressure plate and middle stator disks
and prevents their rotation.
(b) One of these splines is wider than the others. This spline, which is longitudinally drilled
for the probe of the temperature sensor.
(c) A bush assembly, which is an interference fit in the internal flange of the torque plate, is
used as a guide for the brake on the wheel axle.
(d) A heat shield, attached by three bolts, three washers and three fillister rivnuts or by three
bolts, six washers and three nuts, is installed in the torque plate assembly.
Page 6
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 7
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(b) The rotor clips and clip retainers on the rotors prevent damage to carbon when the
torque bars in the wheel cause the rotor assemblies to turn.
(c) The clips which are installed on the pressure plate prevent damage to carbon caused by
the splines of the torque plate when the carbon brake is operated (after accomplishment
of SB 2-1577-32-10).
(d) The heat sink is of the (EDL®) type (Ref. Fig. 5). It has rotors that are a different
thickness than the stators. When the heat sink is worn out, only the set of six thin stators
(includes pressure plate and end plate) or five thin rotors have to be replaced. The disks
that remain again for a second life (after a machining procedure) have to be reused. For
the renovation process for a worn heat sink , Ref. Fig. 5).
Page 8
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 10
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 11
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 12
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
D. Operation
(Ref. Fig. 5)
(Ref. Fig. 6)
(a) The hydraulic pressure supplied through one of the inlet ports (NORMAL or
EMERGENCY) of the piston housing operates the seven pistons at the same time.
(b) The pistons move and push the pressure plate, which compresses the stator and rotor
assemblies against the end plate.
(c) The friction between the stator and rotor assemblies causes braking.
(d) The piston moves and compresses the compression spring between the spring guide
and the piston. The adjuster pin, the ball, the self-locking nut and the adjuster tube do
not move and keep the spring guide in position.
(e) The piston touches the end of the spring guide when the clearance “C” is taken up.
Clearance ”C” can be called ”running clearance”.
(f) Wear “U” of the heat sink makes necessary an added movement of the piston, which
pushes the spring guide and the adjuster tube to a new position on the ball.
(g) The ball expands the adjuster tube which allows the added movement of the piston.
(a) When the pressure decreases, the return spring of each piston pushes the piston and
the spring guide to a position that maintains the total initial clearance “C”. This cancels
the force transmitted by the pressure plate and, as a result, releases the braking torque
in the heat sink.
Page 13
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Operation
FIGURE 6/GRAPHIC32-41-81-991-006-A01
Page 14
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(a) When the wear of the heat sink is maximum, the end of the wear indicators are aligned
(“flush”) with the piston housing.
(a) The heat released when the carbon brake is operated causes the temperature of the
probe to increase.
(b) The increase in temperature causes a potential voltage at the alumel-chromel junction.
This voltage that is caused across pins “A” and “C” of the connector is transmitted to
the monitoring system.
Page 15
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 16
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TASK 32-41-81-700-801-A01
1. Testing
(2) Consumables
(a) The table below gives the consumables necessary to do the test of the component.
NOTE: You can use alternatives for the listed items.
REFERENCE NAME
Hydraulic fluid as per NSA 307110 type IV Hydraulic fluid
Page 1001
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
C. Job set-up
(1) Test conditions
(a) Do all the tests in normal standard test laboratory ambient conditions:
– Ambient temperature: 25 ± 15 °C (77 ± 59 °F).
– Ambient barometric pressure: 840 to 1070 mbar (12.18 to 15.52 psi).
– Relative humidity: Less than 85 %.
(b) For each carbon brake sent to the repair shop, include the remaining length of the wear
indicator pin (1-265) with the carbon brake. This dimension is usually measured on the
aircraft with the park brake pressure. If this was not done, refer to the procedure that
follows: (Ref. SUBTASK 32-41-81-700-002-A01).
D. Procedure
(Ref. Fig. IPL 01)
SUBTASK 32-41-81-700-001-A01
(1) Initial steps
(a) Remove the tool AC21910100 from the heat sink (1-335).
(b) Remove the protective cap (1-231) from each hydraulic fitting assembly (1-230).
(d) Remove the protective cap (1-215) from each valve (1-200).
(e) Connect the one end of the tool AC21858200 to each valve (1-200) and place the other
end to the drip tray.
Page 1002
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-700-002-A01
(2) Measurement of the remaining length of the wear indicator pin (1-265)
CAUTION: MAKE SURE THAT NO HYDRAULIC FLUID FALLS ON THE HEAT SINK
(1-335). THROUGHOUT ALL THE TESTS, NO EXTERNAL SEEPAGE
THROUGH THE WALLS MUST BE OBSERVED.
NOTE: Do this test only if the remaining length of the wear indicator pins (1-265) was
not measured on the aircraft.
(a) Apply a pressure between 165 and 185 bar (2400 and 2685 psi) to one of the two circuits
of the carbon brake.
(b) Measure the length of the wear indicator pins (1-265) (Ref. Fig. 1001).
NOTE: If the end of the wear indicator pins (1-265) are aligned (“flush”) with the piston
housing assembly (1-015), the heat sink (1-335) is fully worn.
Page 1003
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 1004
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-710-001-A01
(3) Flush and bleed procedures of the carbon brake
CAUTION: MAKE SURE THAT NO HYDRAULIC FLUID FALLS ON THE HEAT SINK
(1-335). THROUGHOUT ALL THE TESTS, NO EXTERNAL SEEPAGE
THROUGH THE WALLS MUST BE OBSERVED.
SUBTASK 32-41-81-790-001-A01
(4) Leakage test of the carbon brake
CAUTION: MAKE SURE THAT NO HYDRAULIC FLUID FALLS ON THE HEAT SINK
(1-335). THROUGHOUT ALL THE TESTS, NO EXTERNAL SEEPAGE
THROUGH THE WALLS MUST BE OBSERVED.
(a) Slowly apply a pressure of between 207 and 210 bar (3000 and 3045 psi) to one of
the two circuits of carbon brake.
(b) Hold this pressure for five minutes and make sure that there are no external leakage and
no pressure drop.
Page 1005
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-780-001-A01
(5) Low pressure leakage test of the carbon brake
CAUTION: MAKE SURE THAT NO HYDRAULIC FLUID FALLS ON THE HEAT SINK
(1-335). THROUGHOUT ALL THE TESTS, NO EXTERNAL SEEPAGE
THROUGH THE WALLS MUST BE OBSERVED.
(a) Apply a pressure of between 0,2 and 0,5 bar (3 and 7 psi) to the two circuits of the
carbon brake.
(b) Hold this pressure for five minutes and make sure that there are no external leakage and
no pressure drop.
(c) Decrease the pressure to zero.
SUBTASK 32-41-81-700-003-A01
(6) Operation tests of the carbon brake
CAUTION: MAKE SURE THAT NO HYDRAULIC FLUID FALLS ON THE HEAT SINK
(1-335). THROUGHOUT ALL THE TESTS, NO EXTERNAL SEEPAGE
THROUGH THE WALLS MUST BE OBSERVED.
NOTE: After the accomplishment of steps (a) and (b), do again all the tests on the other
circuit.
Page 1006
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
3 Decrease the pressure to between 17 and 18 bar (245 and 260 psi).
4 Rotor 1 must not be free to be turned by hand.
5 Decrease the pressure to between 10 and 12 bar (145 and 170 psi).
6 Rotor 1 must be free to be turned by hand.
7 Change the pressure from 0 to 69 bar (0 to 1000 psi) for five times to make sure that
the operation of piston/adjuster mechanism is satisfactory.
8 Decrease the pressure to zero.
Page 1007
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 1008
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-750-001-A01
(7) Ground continuity test
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
NOTE: The following test is optional and is let to the shop convenience.
(a) Connect the ground continuity tester between the connector of the temperature sensor
assembly (1-250) and the torque arm bushing (1-030). The torque arm bushings (1-030)
can be cadmium plated.
(b) Make sure that the resistance is not more than 20 milliohms.
SUBTASK 32-41-81-700-004-A01
(8) Last steps
(b) Install the protective cap (1-231) on each hydraulic fitting assembly (1-230).
Page 1009
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TASK 32-41-81-800-001-A01
2. Fault Isolation
Not applicable.
(2) Consumables
Not applicable.
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
SUBTASK 32-41-81-040-002-A01 Disassembly of the housing and adjuster piston
assembly (1-010)
SUBTASK 32-41-81-040-003-A01 Disassembly of adjuster assembly (1-055)
SUBTASK 32-41-81-200-005-A01 Adjuster assembly (1-055)
SUBTASK 32-41-81-440-002-A01 Assembly of the piston (1-070)
SUBTASK 32-41-81-440-003-A01 Assembly of the housing and adjuster piston
assembly (1-010)
SUBTASK 32-41-81-790-001-A01 Leakage test of the carbon brake
C. Job set-up
Not applicable.
Page 1010
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
D. Procedure
(Ref. Fig. IPL 01)
SUBTASK 32-41-81-810-001-A01
(1) Fault isolation of the carbon brake
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
Page 1011
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 1012
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 1013
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 1014
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
DISASSEMBLY
TASK 32-41-81-000-801-A01
1. Disassembly
(2) Disassembly gives step-by-step instructions for a complete disassembly of the component in
a logical sequence and to access any faulty sub-assembly and parts.
(2) Consumables
(a) The table below gives the consumables necessary to disassemble the component.
NOTE: You can use alternatives for the listed items.
Page 3001
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REFERENCE NAME
Commercially available Adhesive tape
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
(Exploded view)
Component Maintenance Manual 32-41-54 Component Maintenance Manual of the
Temperature Sensor
C. Job set-up
Not applicable.
D. Procedure
(Ref. Fig. IPL 01)
SUBTASK 32-41-81-000-001-A01
(1) Recommendation
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) At each cycle (one cycle = full wear of the heat sink (1-335)), it is recommended to
discard:
– The self-locking nuts (1-150) (mandatory). The self locking-nut (1-150) can be
cadmium plated.
– The adjuster tubes (1-140) (mandatory).
– The retaining clips (1-270).
Page 3002
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-000-002-A01
(2) Measurement of the remaining wear
(a) Pressurize the brake between 165 and 185 bar (2400 and 2685 psi) through one of
the two circuits.
(b) Measure the length of the wear indicator pin. If the end of the wear indicator pin is
aligned (“flush”) with the piston housing, the heat sink is fully worn. Refer to SL 1685 for
Goodrich-Messier Inc. Customers and SL 1701 for Messier-Goodrich S.A. Customers for
heat sink return instructions, and fill the “Carbon Return Data Form” from SL.
Page 3003
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-010-001-A01
(3) Removal of the cable guide (1-275)
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Cut the lockwire (1-330). Discard it.
(b) Loosen and remove the screw (1-285) and the washer (1-280). The washer (1-280)
can be cadmium plated.
Page 3004
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-010-002-A01
(4) Removal of the temperature sensor assembly (1-250)
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Install the protective cap.
(c) Loosen and remove the screw (1-260) and the washer (1-255). The washer (1-255)
can be cadmium plated.
Page 3005
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-010-003-A01
(5) Removal of the housing and adjuster piston assembly (1-010) from the torque plate assembly
(1-420) / heat sink (1-335)
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
CAUTION: MAKE SURE THAT NO HYDRAULIC FLUID FALLS ON THE HEAT SINK
(1-335).
CAUTION: IF THE HEAT SINK (1-335) IS NOT FULLY WORN, DO NOT DISCARD THE
WEAR INDICATOR PINS(1-265). THEY WILL BE REUSED WITH THE SAME
HEAT SINK (1-335).
(b) Loosen and remove the bolts (1-465) in criss-cross sequence. Remove the washers
(1-470). The washers (1-470) can be cadmium plated.
(c) Remove the housing and adjuster piston assembly (1-010) from the torque plate
assembly (1-420).
Page 3006
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-010-004-A01
(6) Removal of the heat sink
CAUTION: THE CARBON DISKS ARE BREAKABLE. DO NOT LET THEM FALL OR HIT
HARD OBJECTS. IF THEY ARE DAMAGED, EXAMINE THEM AS WRITTEN
IN THE INSPECTION/CHECK SECTION.
CAUTION: WHEN YOU DISASSEMBLE THE HEAT SINK (1-335), DO NOT LET THE
CARBON DISKS TOUCH THE MATERIALS THAT FOLLOW:
– STRIPPERS.
– GREASE OR OIL.
– PAINTS (THERMOCOLOR, MARKING AND RED LEAD TYPES).
– CHALK.
– HYDRAULIC FLUID.
CAUTION: IF THE HEAT SINK (1-335) IS NOT FULLY WORN, YOU CAN USE IT
AGAIN AFTER INSPECTION (REFER TO THE INSPECTION/CHECK
SECTION). UNTIL IT IS FULLY WORN, MAKE SURE THAT YOU KEEP THE
CARBON DISKS (ROTORS AND STATORS) IN ORDER. TO DO THIS, IT
IS MANDATORY, DURING REMOVAL, TO PUT MARKS ON THE ROTOR
ASSEMBLIES AND ON STATOR ASSEMBLIES. THE MARKS ON THESE
PARTS GIVE THE CORRECT POSITION AND LOCATION OF THE CARBON
DISKS AND OF THEIR MATING FACES. USE AN ADHESIVE TAPE. (REF.
FIG. 3001).
(a) Remove the pressure plate assembly (1-340) together with its two wear indicator pins
(1-265).
CAUTION: REMOVE THE WEAR INDICATOR PINS (1-265) ONLY IF THEY ARE FLUSH
WITH THE PISTON HOUSING.
(d) Remove the rotor disk assemblies (1-360) and the stator disks (1-385) from the torque
plate assembly (1-420).
(e) Remove the four clips (1-410), then remove the end plate disk assembly (1-390). Discard
the clips (1-410).
Page 3007
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 3008
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-040-001-A01
(7) Disassembly of the torque plate assembly
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Remove the heat shield with one of the following methods:
Method 1:
1 Loosen and remove the bolts (1-455), the washers (1-450) and the heat shield
assembly (1-445). The bolts (1-455) and the washers (1-450) can be cadmium plated.
Method 2:
2 Loosen and remove the nuts (1-461). Remove the washers (1-462). The nuts
(1-461) can be cadmium plated.
3 Remove the bolts (1-455) and the washers (1-450). Remove the heat shield assembly
(1-445). The bolts (1-455) and the washers (1-450) can be cadmium plated.
(b) Remove the retaining ring (1-440) only if you remove the “bushing assembly” (bushings
(1-430) and (1-435)).
NOTE: Remove the “bushing assembly” only if you have found a defect (refer to the
INSPECTION / CHECK section).
Page 3009
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-040-002-A01
(8) Disassembly of the housing and adjuster piston assembly (1-010)
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) If necessary, drain hydraulic fluid from the piston housing assembly (1-015).
(c) Remove the preformed packings (1-210B) from the valves (1-200).
NOTE: Remove and discard the preformed packings (1-210B) only if necessary, if you
find signs of damage or every four cycles.
(e) Remove the preformed packings (1-225) from the hydraulic fitting assembly (1-230).
Discard it.
NOTE: Remove and discard the preformed packings (1-225) only if necessary, if you
find signs of damage or every four cycles.
(f) Record all the information shown on the identification plate (1-480) and the instruction
plate (1-485).
(g) Remove the identification plate (1-480) and the instruction plate (1-485).
Page 3010
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
WARNING : REMOVAL OF THE PISTON (1-070) FROM THE PISTON SLEEVE (1-060)
CAN CAUSE A SPRAY OF HYDRAULIC FLUID. HYDRAULIC FLUID IS
FLAMMABLE AND DANGEROUS TO SKIN, EYES, AND RESPIRATORY
TRACT. SKIN AND EYE PROTECTION IS REQUIRED. PREVENT
REPEATED TOUCH OF THE FLUID, OR TOUCH FOR A LONG TIME. GOOD
GENERAL AIR FLOW IS USUALLY SUFFICIENT.
(i) Push back the pistons (1-070), then remove the adjuster assemblies (1-055) with the
tool Q47621.
(j) Loosen and remove the screws (1-325). Remove the washers (1-320) and the cable
bracket assembly (1-290). The washers (1-320) can be cadmium plated.
(k) Remove:
– Before SB 2-1577-32-4: the lubrication fittings (1-040).
– After SB 2-1577-32-4: the lubrication fittings (1-040) and (1-043).
(l) Remove the nut (1-190), the washers (1-180), the bolt (1-185), the collar (1-175) and the
torque pin (1-170). The nut (1-190), the washers (1-180), the bolt (1-185) and the collar
(1-175) can be cadmium plated.
(m) Remove the preformed packing (1-245) with the tool 89901. Discard it.
Page 3011
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-040-003-A01
(9) Disassembly of the adjuster assembly (1-055)
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Pull out the insulator assembly (1-155).
(b) Remove the retaining ring (1-160). Discard it.
(c) Remove the instruction plate (1-135).
(d) Loosen and remove the self-locking nut (1-150) from the adjuster pin (1-110). Discard
the self-locking nut (1-150). The self locking-nut (1-150) can be cadmium plated.
(e) Remove the ball (1-145), together with the adjuster tube (1-140), from the piston (1-070).
(f) Remove the ball (1-145) from the adjuster tube (1-140). Discard the adjuster tube (1-140).
(g) Remove the adjuster pin (1-110) and the pin retainer (1-105). The pin retainer (1-105)
can be cadmium plated.
(h) Remove the piston (1-070), together with its components from the piston sleeve (1-060).
(i) Remove the scraper ring assembly (1-065) from the piston sleeve (1-060) with the tool
89901.
NOTE: Remove and discard the scraper ring assembly (1-065) only if necessary, if you
find signs of damage or every four cycles.
(j) Remove the preformed packing (1-045) from the piston sleeve (1-060) with the tool
89901. Discard the preformed packing (1-045).
(k) Remove the back-up rings (1-163) from the piston sleeve (1-060).
NOTE: Remove and discard the back-up rings (1-163) only if necessary, if you find
signs of damage or every four cycles.
(l) Remove the preformed packing (1-080) from the piston (1-070) with the tool 89901.
Page 3012
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(n) Remove the back-up rings (1-075) from the piston (1-070).
NOTE: Remove and discard the back-up ring (1-075) only if necessary, if you find
signs of damage or every four cycles.
(o) Remove the retaining ring (1-100) and the seal retainer (1-095) from the piston (1-070).
(p) Remove the preformed packing (1-090) from the piston (1-070) with the tool 89901.
(r) Remove the back-up rings (1-085) from the piston (1-070).
(t) Install the piston (1-070) together with its components under a press, then with the tool
Q46498 put on the spring guide (1-115), compress the spring (1-125) enough to access
the second groove of the piston (1-070).
(u) Remove the retaining ring (1-130) and slowly remove the force applied to the spring
(1-125).
(w) Remove the spring guide (1-115) from the piston (1-070).
(x) Remove the spring (1-125) and the guide sleeve (1-120) from the piston (1-070).
Page 3013
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 3014
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
CLEANING
TASK 32-41-81-100-801-A01
1. Cleaning
(2) Consumables
(a) The table below gives the consumables necessary to clean the parts.
NOTE: You can use alternatives for the listed items.
REFERENCE NAME
Commercially available Clean and soft lint-free cloth
WHITE SPIRIT or cleaning product as per Cleaning product
MIL-PRF-680 Type II or III
PERCHLOROETHYLENE (MIL-T-81533) Cleaning product
APPLIED 4-204 CLEANER Aqueous cleaning product
AQUASPRAY 102 Aqueous cleaning product
ARDROX 6333 Aqueous cleaning product
ARMAKLEEN M-HP2 Aqueous cleaning product
BIG BLUE Aqueous cleaning product
Page 4001
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REFERENCE NAME
BRULIN 1990 GD Aqueous cleaning product
BRULIN 815 GD Aqueous cleaning product
CALGON 6215 Aqueous cleaning product
CEE-BEE A7X7 Aqueous cleaning product
CEE-BEE 280 Aqueous cleaning product
DUBOIS MULTI-TERJ 1012 Aqueous cleaning product
ELDORADO ED-306LF Aqueous cleaning product
MAGNUS HDL-330 Aqueous cleaning product
MAGNUS SOLUWAX Aqueous cleaning product
MAGNUS AERODET Aqueous cleaning product
MIRACHEM 500 Aqueous cleaning product
MIRACHEM 750LF Aqueous cleaning product
RAINBOW JET Aqueous cleaning product
RAM WASH H.D Aqueous cleaning product
SAG 710 (anti-foam) Aqueous cleaning product
SUPER BEE 300LF Aqueous cleaning product
SAG 710 Aqueous cleaning product
(anti-foam)
SUPERCLEAN RP 98 A Aqueous cleaning product
TURCO 3878 LF-NC Aqueous cleaning product
TURCO 6751-L Aqueous cleaning product
TURCO 6849 Aqueous cleaning product
TURCO AVIATION Aqueous cleaning product
TURCO SPRAYEZE NPLT Aqueous cleaning product
ZOK27 Aqueous cleaning product
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
CMM 32-41-54 Component Maintenance Manual of the
Temperature Sensor
C. Job set-up
Not applicable.
Page 4002
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
D. Procedure
(Ref. Fig. IPL 01)
SUBTASK 32-41-81-110-001-A01
(1) Cleaning of the heat sink
CAUTION: THE CARBON DISKS ARE BREAKABLE. DO NOT LET THEM FALL OR HIT
HARD OBJECTS. IF THEY ARE DAMAGED, EXAMINE THEM AS WRITTEN
IN THE INSPECTION/CHECK SECTION.
CAUTION: WHEN YOU CLEAN THE HEAT SINK (1-335), DO NOT LET THE CARBON
DISKS TOUCH THE MATERIALS THAT FOLLOW:
– STRIPPERS.
– GREASE OR OIL.
– PAINTS (THERMOCOLOR, MARKING AND RED LEAD TYPES).
– CHALK.
– HYDRAULIC FLUID (REF. FIG. 4001).
Page 4003
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
1 Clean the pressure plate assembly (1-340), stator disks (1-385), rotor disk assembly
(1-360) and end plate disk assembly (1-390) with a vacuum cleaning machine and
with a nylon bristle brush.
1 Remove unwanted materials with a nylon brush and a clean and soft lint-free cloth
made moist with PERCHLOROETHYLENE (MIL-T-81533) cleaning product.
2 Dry all the parts with compressed air.
Page 4004
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 4005
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-100-001-A01
(2) Cleaning of the temperature sensor
SUBTASK 32-41-81-110-002-A01
(3) Cleaning of other parts
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Clean all the metal parts with WHITE SPIRIT or ISOPROPYL ALCOHOL or cleaning
product as per MIL-PRF-680 Type II or III.
(b) Dry all the parts with compressed air or with a clean and soft lint-free cloth.
Page 4006
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TASK 32-41-81-100-802-A01
2. Paint removal from Piston Housing
(a) The table below gives the tools, fixtures and equipment necessary to clean the parts.
NOTE: You can use alternatives for the listed items.
(2) Consumables
Not applicable.
REFERENCE DESIGNATION
Standard Practices Manual 32-09-01, section Sealing of mating parts with sealant
25
Standard Practices Manual 32-09-01, section Paint stripping by local application method
28
Standard Practices Manual 32-09-01, section Paint stripping by the bath method
29
Standard Practices Manual 32-09-01, section Paint stripping by the “seed” blasting method
30
Standard Practices Manual 32-09-01, section Paint removal by plastic media blasting method
70
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
C. Job set-up
Not applicable.
Page 4007
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
D. Procedure
(Ref. Fig. IPL 01)
SUBTASK 32-41-81-110-003-A01
(1) Initial steps
(a) Before paint removal, apply sealant to the mating surfaces and lee plugs of the piston
housing assembly (1-015), as written in the section 25 of the Standard Practices Manual
32-09-01.
SUBTASK 32-41-81-110-004-A01
(2) Chemical procedure
1 Paint remover as written in the section 29 of the Standard Practices Manual 32-09-01.
2 Paint remover as written in the section 28 of the Standard Practices Manual
32-09-01, for local repair of the paint.
3 Paint remover (SAE-AMS1375).
(b) After paint removal, wash the piston housing assembly (1-015) with cold water.
(c) Dry the piston housing assembly (1-015) with compressed air.
Page 4008
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-120-001-A01
(3) Abrasive procedure
(b) Blast with PLASTIC MEDIA as per MIL-P-85891 (max hardness of 3.5 MOH) or as
written in the section 70 of the Standard Practices Manual 32-09-01, or with WALNUT
HULLS as per A-A-1722 type II grade 20 / 30 or as written in the section 30 of the
Standard Practices Manual 32-09-01.
(c) After paint removal, wash the piston housing assembly (1-015) with cold water.
(d) Dry the piston housing assembly (1-015) with compressed air or with a clean and soft
lint-free cloth.
Page 4009
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TASK 32-41-81-100-803-A01
3. Paint removal from the Torque Plate (1-425)
(2) Consumables
Not applicable.
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
Standard Practices Manual 32-09-01, section 325-mesh grit wet blasting
19
C. Job set-up
Not applicable.
D. Procedure
(Ref. Fig. IPL 01)
SUBTASK 32-41-81-120-002-A01
(1) Sand blast procedure
(a) Apply mask material the threaded holes of the torque plate (1-425).
(b) If not removed, apply mask material the bushings.
(c) Remove the paint by lightly sand blasting as written in the section 19 of the Standard
Practices Manual 32-09-01.
(d) After paint removal, wash the part with cold water.
Page 4010
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(e) Dry the torque plate (1-425) with compressed air or with a clean and soft lint-free cloth.
NOTE: If you do not repair the protection of the parts within two hours, apply a
temporary protection to them as written in the REPAIR 8 section.
Page 4011
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 4012
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
INSPECTION/CHECK
TASK 32-41-81-200-801-A01
1. Inspection / Check
(a) The table below gives the tools, fixtures and equipment necessary to check the
component.
NOTE: You can use alternatives for the listed items.
(2) Consumables
Not applicable.
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
CMM 32-41-54 Component Maintenance Manual of the
Temperature Sensor
Standard Practices Manual 32-09-01, section Detection of defects by fluorescent penetrant
38 inspection
Standard Practices Manual 32-09-01, section Eddy current crack detection
41
Standard Practices Manual 32-09-01, section Magnetic particle inspection
42
C. Job set-up
Not applicable.
Page 5001
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
D. Procedure
(Ref. Fig. IPL 01)
CAUTION: DO THE VISUAL CHECK OF THE PARTS BEFORE YOU ASSEMBLE THE
COMPONENT.
SUBTASK 32-41-81-200-001-A01
(1) General
NOTE: A heat sink (1-335) is fully worn when the wear indicator pins (1-265) are aligned
(“flush”) with the piston housing assembly (1-015).
1 At every heat sink (1-335) replacement (full wear of the heat sink (1-335)).
– At each cycle (cycle = full wear of the heat sink (1-335)), refer to the table below.
– Every four cycles, refer to the table below.
2 Deterioration / Failures (removal before full wear of the heat sink (1-335)).
– Overheating caused by a rejected take-off, refer to the table below.
– Overheating caused by a dragging brake, refer to the table below.
– Leakage (refer to TESTING AND FAULT ISOLATION section).
Page 5002
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
CYCLES
PART INSPECTION PROCEDURE *
1 2 3 4
Piston housing (1-020) Visual inspection X X X X X
Penetrant inspection X X
Dimensional check X X
Conductivity test (IACS) X
Hardness test X
Torque pin (1-170) Visual inspection X X X X X
Magnetic particle inspection X X X X X
Dimensional check X X
Torque plate assembly (1-420) Visual inspection X X X X X
Magnetic particle inspection X X
Dimensional check X X X X X
Hardness test X
Adjuster assembly (1-055)
- Piston sleeve (1-060) Visual inspection X X X X X
- Piston (1-070) Visual inspection X X X X X
- Insulator assembly (1-155) Visual inspection X X X X X
- Adjuster pin (1-110) Visual inspection X X X X X
Magnetic particle inspection X X
- Spring guide (1-115) Visual inspection X X X X X
- Guide sleeve(1-120) Visual inspection X X X X X
- Spring (1-125) Dimensional check X X
Bolts (1-465) Visual inspection X X X X X
Penetrant inspection X X
Heat shield assembly (1-415) Visual inspection X X X X X
Temperature sensor assembly Refer to the CMM 32-41-54 X
(1-250)
Heat sink (1-335) (not fully worn) Visual inspection X
Dimensional check X
Cable guide (1-275) Visual inspection X X X X X
Table legend:
– One cycle = full wear of the heat sink (1-335).
– * = signs of overheating (caused by a rejected take-off or a dragging brake) or after
a rejected take-off.
Page 5003
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-200-002-A01
(2) Piston housing (1-020)
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Visual inspection
1 Make sure that there is no scratches in the piston cavities (sealing surface) for the
adjuster assemblies:
– If you find any scratches above the sealing surface, refer to the REPAIR 5 section.
– If you find any scratches at the sealing surface, discard the piston housing (1-020).
2 Examine all internal threads for satisfactory condition (no stripping of the metal). If
there is a defect, discard the piston housing (1-020).
3 Make sure that the bushings (1-025) and (1-030) are in the correct position (not
moved). The bushings that have moved can be replaced with the bushings (1-025B)
and (1-030B) which have a tighter press fit. Refer to the REPAIR 1 section. The
bushings (1-025) and (1-030) can be cadmium plated.
4 Make sure that there is no corrosion. if you find corrosion, refer to REPAIR GENERAL
section.
5 Make sure that there is no worn / damaged paint. If there is a defect, refer to the
REPAIR 8 section.
Page 5004
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
1 If there was an overheat, do an eddy current conductivity test on the mating surfaces
between the piston housing (1-020) and the torque plate (1-425).
2 If the conductivity is more than 43% IACS, continue with the hardness test.
NOTE: Remove the surface treatment in the areas where the hardness test will be
performed.
1 If there was an overheat and that the value of the conductivity test is not in the limit
range, do a hardness test on the mating surfaces between the piston housing (1-020)
and the torque plate assembly (1-420). Refer to the instructions that follow:
NOTE: It is necessary to remove the paint in the areas where the hardness test
will be performed.
a Use a ball with a diameter of 10 mm (0.39 in) and a load of 10000 N (2248.1 lbf).
b Make sure that the minimum hardness is equal to 130 HB.
c If the hardness is not in the limit range, discard the piston housing (1-020).
d Repair the protection of the piston housing (1-020). Refer to the REPAIR 8
section.
e If you do not repair the protection of the part within two hours, apply a temporary
protection to it as written in the REPAIR GENERAL section.
Page 5005
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Hardness tests
FIGURE 5001/GRAPHIC32-41-81-991-012-A01
Page 5006
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 5007
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-200-003-A01
(3) Torque pin
1 Make sure that their is no tool marks, cracks and plating defects in the flange radius
of the torque pins (1-170).
2 If there is a defect, discard the torque pin (1-170).
1 Examine for cracks, tool marks, and plating defects in the torque pin (1-170) by a
magnetic particle inspection specially at the flange radius. Refer to section 42 of the
Standard Practices Manual 32-09-01 or to ASTM E1444.
NOTE: It is not necessary to remove the surface treatment before a magnetic
particle inspection.
1 Do a dimensional check of the torque pins (1-170) (refer to FITS AND CLEARANCES
section for the wear limits).
SUBTASK 32-41-81-200-004-A01
(4) Torque plate assembly (1-420)
1 Check the position and the internal diameter of the bushings (1-430) and (1-435).
Refer to the REPAIR section for the replacement of the bushing assembly.
NOTE: If the inner diameter of the bushing (1-430) is more than 166 mm (6.535
in), the bushing can continue to be used if it is machined to the correct
diameter (refer to the REPAIR 2 section). Before machining the bushing
(1-430) make sure that it is well seated in its housing.
NOTE: If the inner diameter of the bushing (1-430) is less than 166 mm (6.535
in), discard it.
2 Make sure that there is no excessive wear of the metal on the splines and on the
torque button contact areas (Ref. Fig. 5003). If there is a defect refer to REPAIR 6
section.
3 Make sure that there are no peening marks in the torque button bores and on the
mating faces. If there is a defect, refer to REPAIR 6 section (Ref. Fig. 5003).
4 Make sure that all internal threads are in satisfactory condition (no stripping of the
metal).
5 Inspect the torque plate assembly (1-420) for corrosion. If corrosion is found, refer to
the REPAIR 6 section.
Page 5008
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
6 Inspect the torque plate heat shield assembly (1-445) for cracks or other signs
of damage. Make sure that cracks at the cooling holes are acceptable. If crack is
found at the attachment holes, refer to the REPAIR 3 section. Only cracks between
the cooling holes and the inner diameter of the heat shield are acceptable (Ref.
Fig. 6005).
NOTE: Cracks are not acceptable within the 12,7 mm (0.500 in) radius of the heat
shield mounting hole center.
1 If there was an overheat, do a hardness test on the torque plate assembly (1-420).
Refer to the instructions that follow:
a Use a ball with a diameter of 10 mm (0.39 in) and a load of 10000 N (2248.1 lbf).
b Make sure that the minimum hardness is equal to 285 HB 30 HRC.
c If the hardness is not in the limit range, discard the torque plate assembly (1-420).
d Repair the protection of the torque plate assembly (1-420). Refer to the REPAIR
8 section.
e If you do not repair the protection of the part within two hours, apply a temporary
protection to it as written in the REPAIR GENERAL section.
2 After the hardness test, machine the areas in which you did the test. Then, apply a
temporary protection to them as written in the REPAIR 8 section.
NOTE: If you do not repair the protection of the part within two hours, apply a
temporary protection to it as written in the REPAIR GENERAL section.
Page 5009
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 5010
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-200-005-A01
(5) Adjuster assembly (1-055)
Page 5011
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
1 Visual inspection
a Make sure that there are no scratches or detached parts on the guide sleeve
(1-120).
b If there is a defect, refer REPAIR 4 section.
b If any values are not in these tolerances, discard the spring (1-125).
Page 5012
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 5013
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-200-006-A01
(6) Bolts (1-465)
1 Do a penetrant inspection of the each bolt (1-465). Refer to the section 38 Standard
Practices Manual 32-09-01 or ASTM E1417.
2 If you find a crack, discard the defective bolt (1-465).
SUBTASK 32-41-81-200-007-A01
(7) Heat shield assembly (1-415)
1 Check for cracks, defective welding spot or other signs of damage on the heat shield
assembly (1-415).
2 If you find crack at the ventilation holes or on the tabs area, refer to REPAIR 3 section.
SUBTASK 32-41-81-200-008-A01
(8) Temperature sensor assembly (1-250)
Page 5014
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-200-009-A01
(9) Heat sink (1-335)
CAUTION: THE CARBON DISKS ARE BREAKABLE. DO NOT LET THEM FALL OR HIT
HARD OBJECTS. IF THEY ARE DAMAGED, EXAMINE THEM AS WRITTEN
IN THE INSPECTION/CHECK SECTION.
CAUTION: WHEN YOU EXAMINE THE HEAT SINK (1-335), DO NOT LET THE CARBON
DISKS TOUCH THE MATERIALS THAT FOLLOW:
– STRIPPERS.
– GREASE OR OIL.
– PAINTS (THERMOCOLOR, MARKING AND RED LEAD TYPES).
– CHALK.
– HYDRAULIC FLUID.
NOTE: Inspection of each carbon disk is required in order to reuse a heat sink not
completely worn. A worn out heat sink may be submitted to inspection but this
is not necessary.
NOTE: Heat sink that not comply with inspection criteria and worn out heat sinks have to
be replaced in the frame of the EDL®. Return Policy depending on the supplier
as follows:
– Airlines/brake repair stations which currently deal with Messier-Goodrich S.A.
(FRANCE): Refer to SL 1701.
– Airlines/brake repair stations which currently deal with Goodrich-Messier Inc.
(U.S.A.): Refer to SL 1685.
NOTE: It is recommended to clean the carbon disks before they are examined (refer to
the CLEANING section). The parts must be cleaned if the heat sink (1-335) will
return to service (not fully worn).
NOTE: Do not remove rotor hardware (clips, clip retainers, and rivets) and pressure plate
inserts or torque buttons from end plate.
Page 5015
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
4 Non-wear surfaces
a Make sure that there is no damage deeper than 1,52 mm (0.060 inch) or more
than 4,84 cm² (0.750 in²).
b Make sure that the inserts on the pressure plate are not loose.
8 Oxidation:
a Scratch the non-wear surfaces by means of fingernail and check that carbon
material does not crumble when a finger nail is forced into the material (Ref. Fig.
5006). Refer to the SL 2091 for inspection of catalytic oxidation.
Page 5016
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 5017
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 5018
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
1 Do a dimensional check of rotor clips drive slots, stator slots and pressure plate slots
for wear. Make sure that the dimensions are within limits.
NOTE: Do not try to resurface damaged clips.
2 Loose clip retainers are acceptable if a shim thickness 0,38 mm (0.015 in) maximum
will go between the retainer and the carbon disk.
Page 5019
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 5020
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-200-010-A01
(10) Cable guide (1-275)
1 Check for cracks in the loops at the welding point and in the attachment area.
2 If you found crack, refer to REPAIR 7 section.
Page 5021
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 5022
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR
TASK 32-41-81-300-801-A01
1. Repair - General
(2) Consumables
(a) The table below gives the consumables necessary to do the maintenance of the
component.
NOTE: You can use alternatives for the listed items.
REFERENCE NAME
Commercially available Abrasive paper (#400 and #600 grit)
WD-40 or corrosion preventive oil as per Corrosion preventive oil
MIL-PRF-81309
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
(Exploded view)
Standard Practices Manual 32-09-01, section Corrosion removal and cold-phosphate
21A treatment of ferrous metals
Standard Practices Manual 32-09-01, section Corrosion removal from aluminium and its
22 alloys (passivating method)
Page 6001
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
C. Job set-up
Not applicable.
D. Procedure
(Ref. Fig. IPL 01)
WARNING : MAKE SURE THAT YOU OBEY ALL THE HEALTH AND SAFETY
PRECAUTIONS OF THE MANUFACTURERS OF THE MATERIALS.
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE REPAIR. REFER
TO THE CLEANING SECTION.
SUBTASK 32-41-81-320-001-A01
(1) “Blend repair” procedure
(a) A "blend repair" procedure gradually changes the contour from the repaired surface to
the adjacent initial surfaces. A "blend repair" procedure removes a minimum quantity
of metal and makes a smooth surface (without scratches). Use fine-grit abrasive paper
(#600) to remove scratches that are made by large-grit abrasive paper.
SUBTASK 32-41-81-320-002-A01
(2) Corrosion removal from aluminium alloy parts
NOTE: This procedure is applicable whatever the level of corrosion you possibly find on
aluminium alloy parts.
(a) To remove signs of corrosion, brush or rub the part with large-grit abrasive paper (#400).
Keep to the MINIMUM or MAXIMUM dimensions BEFORE PROTECTION (outside
diameter, inside diameter or thickness). Keep to the MINIMUM web thickness limits when
you locally brush or rub the contour of the part.
(b) Remove scratches that are made by large-grit abrasive paper (#400), with a "blend repair"
procedure. Refer to the procedure that follows: (Ref. SUBTASK 32-41-81-320-001-A01).
(c) Remove corrosion which stays after the above operation, by a chemical procedure, with a
corrosion remover as written in the section 22 of the Standard Practices Manual 32-09-01.
(d) Repair the protection of the part. Refer to the REPAIR 8 section.
NOTE: If you do not repair the protection of the part within two hours, apply a
temporary protection to it. Refer to the procedure that follows: (Ref. SUBTASK
32-41-81-350-001-A01).
Page 6002
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-320-003-A01
(3) Corrosion removal from steel parts
NOTE: This procedure is applicable whatever the level of corrosion you possibly find on
steel parts.
(a) Brush the part to remove signs of corrosion. Keep to the MINIMUM or MAXIMUM
dimensions BEFORE PROTECTION (outside diameter, inside diameter or thickness).
Keep to the MINIMUM web thickness limits when you locally brush the contour of the part.
(b) If there are still signs of corrosion, rub the part with large-grit abrasive paper (#400) or
sand blast the part (Ref. SUBTASK 32-41-81-120-002-A01). Keep to the MINIMUM or
MAXIMUM dimensions BEFORE PROTECTION (outside diameter, inside diameter or
thickness). Keep to the MINIMUM web thickness limits when you locally rub or sand blast
the contour of the part.
NOTE: If there are still signs of corrosion on the torque plate (1-425), refer to the
REPAIR 6 section.
(c) Apply a cold-phosphate treatment to the areas where you have removed the corrosion.
Refer to the section 21A of the Standard Practices Manual 32-09-01.
(d) Repair the protection of the part. Refer to the REPAIR 8 section.
NOTE: If you do not repair the protection of the part within two hours, apply a
temporary protection to it. Refer to the procedure that follows: (Ref. SUBTASK
32-41-81-350-001-A01).
SUBTASK 32-41-81-350-001-A01
(4) Temporary protection
(a) Apply a corrosion preventive oil as a temporary protection to the parts which will get
permanent protection subsequently.
NOTE: You can easily remove the corrosion preventive oil with cleaning product. Refer
to the CLEANING section.
SUBTASK 32-41-81-300-001-A01
(5) Symbols on figures
(Ref. Fig. 6001)
(a) Symbols are shown on some figures to show surface finishes, position tolerances,
position, etc.
Page 6003
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Symbol legend
FIGURE 6001/GRAPHIC32-41-81-991-019-A01
Page 6004
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR 1
TASK 32-41-81-300-802-A01
1. Repair 1 - Replacement of loose or damaged Bushings (1-030) and (1-025) in the Piston Housing (1-020)
(a) The table gives the tools, fixtures and equipment necessary to do the maintenance
of the component.
NOTE: You can use alternatives for the listed items.
(2) Consumables
(a) The table below gives the consumables necessary to do the maintenance of the
component.
NOTE: You can use alternatives for the listed items.
REFERENCE NAME
Zinc Chromate Primer (TT-P-1757) Corrosion preventive post primer
MIL-PRF-680 Type II or WHITE SPIRIT Cleaning product
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
(Exploded view)
REPAIR No. 1
Page 6005
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REFERENCE DESIGNATION
Standard Practices Manual 32-09-01, section Local repair of the surface finish on aluminum
14 alloys by chemical oxidizing
SUBTASK 32-41-81-320-001-A01 Corrosion removal
C. Job set-up
Not applicable.
D. Procedure
(Ref. Fig. IPL 01)
SUBTASK 32-41-81-010-005-A01
(1) Removal of the torque arm bushings (1-030)
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Use a hammer and a soft metal drift to remove the loose or damaged torque arm
bushings (1-030) from the piston housing (1-020). The torque arm bushings (1-030)
can be cadmium plated.
NOTE: Replace the two torque arm bushings (1-030) at the same time.
REPAIR No. 1
Page 6006
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-410-001-A01
(2) Installation of the torque arm bushings (1-030)
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Make sure that there are no scratches in the bushing hole.
– The diameter of the bushing hole must be 56,060 mm (2.2071 in) max.
– If it is smaller than 57,305 mm (2.2561 in):
– Use the two torque arm bushing (1-031) for repair only.
– Machine the bushing hole to the diameter (B) and the torque arm bushings (1-031)
to dimensions shown in (Ref. Fig. 6002).
– Apply chemical oxidizer to the machined surface of the bushing hole (refer to the
section 14 of Standard Practices Manual 32-09-01).
(e) Clean the hole to receive the torque arm bushing (1-030) with a cloth made moist with
MIL-PRF-680 Type II or WHITE SPIRIT solvent. The torque arm bushings (1-030) can
be cadmium plated.
(f) Apply a light layer of zinc chromate primer (TT-P-1757) as a spray to the hole.
REPAIR No. 1
Page 6007
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(g) Heat the piston housing to 135 °C (275 °F) maximum for not longer than ten minutes.
(h) Put the heated piston housing on the worktable with appropriate supports under the
piston housing.
(i) Put the cooled bushing in the hole and immediately press it fully into the hole.
(j) Make sure that the maximum clearance under the bushing flange is 0,05 mm (0.002 in).
If the clearance is more than this limit, press the bushing again until its flange is against
the piston housing. If the bushing cannot be installed correctly, remove it immediately
and repeat the tasks (Ref. SUBTASK 32-41-81-010-005-A01) and (Ref. SUBTASK
32-41-81-410-001-A01).
(k) Machine the torque arm bushings (1-030) to the dimensions shown in (Ref. Fig. 6002).
The torque arm bushings (1-030) can be cadmium plated.
REPAIR No. 1
Page 6008
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Replacement of the Torque arm Bushings (1-030) and repair of the Piston Housing (1-020) (Sheet 1 of 2)
FIGURE 6002/GRAPHIC32-41-81-991-020-A01
REPAIR No. 1
Page 6009
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Replacement of the Torque arm Bushings (1-030) and repair of the Piston Housing (1-020) (Sheet 2 of 2)
FIGURE 6002/GRAPHIC32-41-81-991-020-A01
REPAIR No. 1
Page 6010
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-010-006-A01
(3) Removal of the hub bushings (1-025)
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Use a hammer and a soft metal drift to remove the loose or damaged hub bushing (1-025)
from the piston housing (1-020). The hub bushing (1-025) can be cadmium plated.
REPAIR No. 1
Page 6011
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-410-002-A01
(4) Installation of the hub bushings (1-025)
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Make sure that there are no scratches in the bushing hole.
– The diameter of the bushing hole must be 172,365 mm (6.786 in) max.
– If necessary, machine the bushing hole to the diameter (B) and the hub bushing
(1-025) to dimensions shown in (Ref. Fig. 6003). The hub bushing (1-025) can be
cadmium plated.
– Apply chemical oxidizer to the machined surface of the bushing hole (refer to the
section 14 of the Standard Practices Manual 32-09-01).
(e) Clean the hole to receive the hub bushing (1-025) with a cloth made moist with
MIL-PRF-680 Type II or WHITE SPIRIT solvent. The hub bushing (1-025) can be
cadmium plated.
(f) Apply a light layer of zinc chromate primer (TT-P-1757) as a spray to the hole.
(g) Heat the piston housing to 135 °C (275 °F) maximum for not longer than ten minutes.
REPAIR No. 1
Page 6012
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(h) Put the heated piston housing on the worktable with appropriate supports under the
piston housing.
(i) Put the cooled bushing in the hole and immediately press it fully into the hole.
(j) Make sure that the maximum clearance under the bushing flange is 0,05 mm (0.002 in).
If the clearance is more than this limit, press the bushing again until its flange is against
the piston housing. If the bushing cannot be installed correctly, remove it immediately
and repeat the tasks (Ref. SUBTASK 32-41-81-010-006-A01) and (Ref. SUBTASK
32-41-81-410-002-A01).
(k) Machine the hub bushings (1-025) to the dimensions shown in (Ref. Fig. 6003). The hub
bushings (1-025) can be cadmium plated.
REPAIR No. 1
Page 6013
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Replacement of the Hub Bushing (1-025) and repair of the Piston Housing (1-020) (Sheet 1 of 2)
FIGURE 6003/GRAPHIC32-41-81-991-021-A01
REPAIR No. 1
Page 6014
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Replacement of the Hub Bushing (1-025) and repair of the Piston Housing (1-020) (Sheet 2 of 2)
FIGURE 6003/GRAPHIC32-41-81-991-021-A01
REPAIR No. 1
Page 6015
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR No. 1
Page 6016
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR 2
TASK 32-41-81-300-803-A01
1. Repair 2 - Replacement of the Bushing Assembly (1-428) in the Torque Plate (1-425)
(a) The table gives the tools, fixtures and equipment necessary to do the maintenance
of the component.
NOTE: You can use alternatives for the listed items.
(2) Consumables
(a) The table below gives the consumables necessary to do the maintenance of the
component.
NOTE: You can use alternatives for the listed items.
REFERENCE NAME
Zinc Chromate Primer (TT-P-1757) Corrosion inhibition compound
Base material 683-3-2 and catalyst X-310-A Colorless varnish
Base material G3005 and AWL-CAT#3 (H3002) Colorless varnish
MIL-PRF-680 Type II or WHITE SPIRIT Cleaning product
REPAIR No. 2
Page 6017
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
(Exploded view)
SUBTASK 32-41-81-320-001-A01 Corrosion removal
C. Job set-up
Not applicable.
D. Procedure
(Ref. Fig. IPL 01)
SUBTASK 32-41-81-010-007-A01
(1) Removal of the bushing assembly (1-428)
(a) Use the tool AC21866000 to remove the bushing assembly (1-428) from the torque plate.
(b) Remove the bushing (1-435) from the bushing assembly (1-428).
SUBTASK 32-41-81-440-001-A01
(2) Assembly of the bushing assembly (1-428)
(a) Cool the bushing (1-430) to -18 °C (0 °F) minimum in a dry ice chest.
(b) Make sure the bushing is cooled for a minimum of fifteen minutes. Then cool it in liquid
nitrogen or in dry ice in methanol.
(c) Clean the internal diameter of the bushing (1-435) with a cloth moist with MIL-PRF-680
Type II or WHITE SPIRIT solvent.
(d) Put the cooled bushing (1-430) in the bushing (1-435) and immediately press it fully into
the bushing (1-430) with tool AC21867000.
(e) Make sure that the maximum clearance under the bushing flange is 0,05 mm (0.002 in).
If the clearance is more than this limit, press the bushing (1-430) again until its flange
is against the bushing (1-435). If the bushing cannot be installed correctly, remove it
immediately and repeat the tasks (Ref. SUBTASK 32-41-81-010-007-A01) and (Ref.
SUBTASK 32-41-81-440-001-A01).
SUBTASK 32-41-81-410-003-A01
(3) Installation of the bushing assembly (1-428) in the torque plate
(a) Make sure that there are no scratches in the bushing assembly hole.
REPAIR No. 2
Page 6018
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(b) Cool the bushing assembly (1-428) to -18 °C (0 °F) minimum in a dry ice chest.
(c) Make sure that the bushing is cooled for a minimum of fifteen minutes. Then cool it in
liquid nitrogen or in dry ice in methanol.
(d) Clean the hole to receive the bushing with a cloth made moist with MIL-PRF-680 Type II
or WHITE SPIRIT solvent.
(e) Apply a thin layer of zinc chromate primer (TT-P-1757) as a spray to the hole.
(f) Heat the torque plate to 246 °C (475 °F) maximum for not longer than ten minutes.
(g) Put the heated torque plate on the worktable with appropriate supports under the torque
plate.
(h) Put the cooled bushing in the hole and immediately press it fully into the hole with the
tool AC21866000.
(i) Machine the bushing to the dimensions shown in (Ref. Fig. 6004).
(j) Apply protective coating to the bushing assembly with colorless varnish.
1 Use base material 683-3-2 with catalyst X-310-A or base material G3005 with
catalyst AWL-CAT # 3 (H3002).
2 Mixing requirements:
a Mix one part of base 683-3-2 with one part of catalyst X-310-A. Drying time:
one week.
b Mix two parts of base G3005 with one part of catalyst AWL-CAT # 3 (H3002).
Drying time: 24 hours.
NOTE: Prepare only the quantity which is necessary. Pot life of the mixture:
eight hours at 20 °C (68 °F).
REPAIR No. 2
Page 6019
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR No. 2
Page 6020
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR 3
TASK 32-41-81-300-804-A01
1. Repair 3 - Repair of the Heat Shield assemblies (1-445) and (1-415)
(a) The table gives the tools, fixtures and equipment to do the maintenance of the
component.
NOTE: You can use alternatives for the listed items.
(2) Consumables
(a) The table below gives the consumables necessary to do the maintenance of the
component.
NOTE: You can use alternatives for the listed items.
REFERENCE NAME
RTV 106 Sealant
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
(Exploded view)
C. Job set-up
Not applicable.
REPAIR No. 3
Page 6021
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
D. Procedure
(Ref. Fig. IPL 01)
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE REPAIR. REFER
TO THE CLEANING SECTION.
SUBTASK 32-41-81-320-004-A01
(1) Repair of the heat shield assembly (1-445)
CAUTION: CRACKS ARE NOT ACCEPTABLE WITHIN 12,7 MM (0.500 IN) RADIUS OF
THE HEAT SHIELD MOUNTING HOLE CENTER.
CAUTION: CRACKS BETWEEN THE COOLING HOLES AND THE INNER DIAMETER
OF THE HEAT SHIELD ARE ACCEPTABLE.
CAUTION: ONLY ONE CRACK BETWEEN A COOLING HOLE AND THE OUTER
DIAMETER OF THE HEAT SHIELD IS ACCEPTABLE.
(a) Make sure that the heat shield assembly (1-445) is clean (refer to the CLEANING
section).
(b) Apply high temperature RTV 106 in six equally-spaced locations ((Ref. Fig. 6005),
Detail 1).
NOTE: Follow the manufacturer’s recommendation for curing time of the RTV 106.
(c) Drill a 3 mm (0.12 in) diameter stop hole at each end of the crack.
(d) Spotweld a patch over the cracked area ((Ref. Fig. 6005), Detail 2).
NOTE: Use 304 CRES (or equivalent) to form the patch material with thickness of
1,11 to 1,91 mm (0.0437 to 0.0752 in).
(e) Drill a 5,1 mm (0.20 in) diameter hole through the patch in the same location as the
initial attachment hole in the heat shield.
NOTE: Use TIG, MIG or spot welding with stainless steel (304 CRES) to form the
patch material.
REPAIR No. 3
Page 6022
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-320-005-A01
(2) Repair of the heat shield assembly (1-415)
(a) Make sure that the heat shield assembly (1-415) is clean (refer to the CLEANING
section).
(b) Drill a 3 mm (0.12 in) diameter stop hole at each end of the crack.
NOTE: Use 28 gauge stainless steel (304 CRES) to form the patch material.
(d) Tackweld a patch over the cracked area on the ventilation holes area.
NOTE: Use stainless steel (304 CRES or Z6CN 18.09) to form the patch material with
thickness of 0,2 to 0,3 mm (0.079 to 0.0112 in).
(e) Make sure that the heat shield is in its initial shape after the repair.
REPAIR No. 3
Page 6024
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR 4
TASK 32-41-81-300-805-A01
1. Repair 4 - Repair of the Guide Sleeve (1-120)
Not applicable.
(2) Consumables
Not applicable.
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
(Exploded view)
C. Job set-up
Not applicable.
D. Procedure
(Ref. Fig. IPL 01)
SUBTASK 32-41-81-320-006-A01
(1) Repair of the guide sleeve (1-120)
(a) Remove the scratches or detached parts on external surface of the guide sleeve (1-120)
over a length of 5 mm (0.2 in).
– After removing the scratches or detached parts, the length must be to the dimension
shown in (Ref. Fig. 6006).
REPAIR No. 4
Page 6025
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR No. 4
Page 6026
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR 5
TASK 32-41-81-300-806-A01
1. Repair 5 - Repair of the Piston Housing (1-020)
Not applicable.
(2) Consumables
(a) The table below gives the consumables necessary to do the maintenance of the
component.
NOTE: You can use alternatives for the listed items.
REFERENCE NAME
WD-40 or corrosion preventive oil as per Corrosion preventive oil
MIL-PRF-81309
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
(Exploded view)
Standard Practices Manual 32-09-01 section Corrosion removal
19
C. Job set-up
Not applicable.
REPAIR No. 5
Page 6027
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
D. Procedure
(Ref. Fig. IPL 01)
SUBTASK 32-41-81-320-007-A01
(1) Repair of the piston housing (1-020)
(a) Apply a thin layer of protective seal to the inserts, bushings and the Lee plugs.
(b) Mask the other openings and the surfaces that do not have corrosion.
(c) Remove corrosion to a maximum depth of 0,25 mm (0.01 in) by blast procedure. Refer to
the section 19 of the Standard Practices Manual 32-09-01. Blend the damaged area with
a “50-to-1” blend repair (Ref. Fig. 6007).
(d) Apply corrosion preventive oil to the areas where you have removed corrosion.
NOTE: A “50-to-1” diameter for each blend repair is recommended for the flat areas
where a circular repair pattern is possible. A ”50-to-1” blend repair is not
possible for the areas that are not flat. Calculate a “50-to-1” as follows:
1 Measure the depth “d” of the damaged areas (Ref. Fig. 6007). If the depth is more
than the permitted limit, reject the piston housing.
2 Multiple “d” by 50 to get the recommended diameter “D” of a circular repair area.
NOTE: When a circular repair pattern is not possible, make the repair areas as
large as possible with the length and width not more than the diameter
“D”. Radius the sharp edges.
REPAIR No. 5
Page 6028
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-300-002-A01
(2) Replacement of the Heli-Coil thread inserts (1-035) in the cable guide (1-275) mounting holes
NOTE: Repair the cable guide bracket mounting holes using an oversize Heli-Coil insert
or a Heli-Coil twinsert.
If the piston housing (1-020) is not damaged, install a new Heli-Coil insert of the
same size.
If the piston housing (1-020) is damaged, install an oversize Heli-Coil insert. If the
damage is severe, install a new Heli-Coil twinsert.
REPAIR No. 5
Page 6030
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR 6
TASK 32-41-81-300-807-A01
1. Repair 6 - Repair of the Torque Plate (1-425)
(2) Consumables
(a) The table below gives the consumables necessary to do the maintenance of the
component.
NOTE: You can use alternatives for the listed items.
REFERENCE NAME
WD-40 or corrosion preventive oil as per Corrosion preventive oil
MIL-PRF-81309
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
Standard Practices Manual 32-09-01, section Magnetic particle inspection
42 or ASTM E1444
Standard Practices Manual, section 38 Detection of defects by fluorescent penetrant
inspection
REPAIR No. 6
Page 6031
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
C. Job set-up
Not applicable.
D. Procedure
(Ref. Fig. IPL 01)
SUBTASK 32-41-81-320-008-A01
(1) Removal of corrosion or old paint residual on the torque tube
NOTE: Do this procedure only if there are signs of corrosion or old paint residual which
stay after the procedure that follows: (Ref. SUBTASK 32-41-81-320-005-A01).
2 Rub the splines of the torque plate (1-425) with a file or a standard rotating device
with drum sander.
3 Make sure that the dimensions of the splines are in the limits.
4 Apply the protection as written in the REPAIR 8 section.
SUBTASK 32-41-81-320-009-A01
(2) Repair of the torque plate (1-425) at the torque-button contact areas
(Ref. Fig. 6009)
NOTE: No repair of a torque-button contact area is necessary if the damage is not more
than 0,51 mm (0.020 in) deep.
CAUTION: DO NOT APPLY WELD METAL TO AREAS THAT ARE NOT WORN.
(a) Remove the paint (refer to the CLEANING section) and the corrosion or other
contamination to a minimum of 6,4 mm (0.252 in) from the area to be welded.
(b) Clean the torque plate (1-425) (refer to the CLEANING section).
REPAIR No. 6
Page 6032
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
CAUTION: KEEP THE PART AT THE CORRECT TEMPERATURE DURING THE WELD
PROCEDURE. INCORRECT TEMPERATURE CAN CAUSE DAMAGE TO
THE PART OR CAUSE THE WELD TO BREAK.
(c) Pre-heat integral torque plate (1-425) at a temperature between 204 and 260 °C (400
and 500 °F).
NOTE: While the part is being welded, keep all areas of the part at a temperature
between 204 and 315 °C (400 and 600 °F).
NOTE: Do not weld into the hole for the torque buttons. Deposit sufficient filler metal to
make sure that the part can be machined to the correct dimensions.
(d) Built-up the material by argon welding with the following requirements:
– AC or DC 50A current.
– 1,6 mm (0.063 in) diameter tungsten electrode.
– Argon torch spray rate: 9 l/min (2.37 US gal/min).
– 1,6 or 2 mm (0.063 or 0.079 in) diameter BMS metal filler. The harness number of the
deposited BMS metal is equal to that of the torque plate.
(e) Weld with a shielded metal arc weld (stick electrode) or gas tungsten arc weld (TIG or
Heli-arc) or gas metal arc weld (MIG) procedure. Use a “low hydrogen” electrode or filler
metal that is 17-22A(S) alloy (AMS6458) or equivalent.
NOTE: Do not let dirt or moisture on the electrode or filler metal. Do not permit a long
arc, which can let atmospheric contamination of the weld metal. If possible, do
not weld into holes for the torque buttons. Deposit sufficient filler metal to make
sure that the part can be machined to the correct dimensions.
(f) Apply the built-up material one after the other to overlap on each side to prevent too
high or heat rise, while reworking.
CAUTION: YOU MUST NOT WELD THE TORQUE PLATE WITH OXY-ACETYLENE
TORCH. THIS WILL INCREASE THE TEMPERATURE, THAT CAN CHANGE
THE METALLURGICAL CHARACTERISTICS OF THE PART.
(g) Immediately after welding, place the torque plate in an oven at 500 °C (932 °F) for one
hour.
NOTE: Keep each part on its backleg end and do not stack parts.
(h) Stop heating and allow the torque plate to slowly cool inside oven.
(i) Machine the torque plate to the initial dimensions, (Ref. Fig. 6009).
REPAIR No. 6
Page 6033
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(j) Do a magnetic particle or penetrant inspection of the repaired areas for cracks. Refer to
the section 42 or the section 38 of the Standard Practices Manual 32-09-01. If there is
crack, grind it out, then weld and machine the cracked area again.
(k) Apply surface treatment to the torque plate (refer to REPAIR 8 section).
REPAIR No. 6
Page 6034
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Removal of corrosion or old paint residual on the torque tube (spline areas)
FIGURE 6008/GRAPHIC32-41-81-991-026-A01
REPAIR No. 6
Page 6035
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Repair of the Torque Plate (1-425) at the button contact area (Sheet 1 of 2)
FIGURE 6009/GRAPHIC32-41-81-991-027-A01
REPAIR No. 6
Page 6036
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Repair of the Torque Plate (1-425) at the button contact area (Sheet 2 of 2)
FIGURE 6009/GRAPHIC32-41-81-991-027-A01
REPAIR No. 6
Page 6037
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-320-010-A01
(3) Repair the splines of the torque plate (1-425)
(Ref. Fig. 6010)
(a) Repair damaged splines by local blending. The minimum spline height must be 11,86
mm (0.460 in).
CAUTION: DO NOT REWORK THE LATERAL SIDES SURFACES AND KEEP THEM
PARALLEL WITH A MINIMUM WIDTH OF 6,79 MM (0.2673 IN) FOR
NARROW SPLINES AND 14,33 MM (0.5642 IN) FOR THE WIDE SPLINE.
1 Repair the damage on the top surface of the spline by local blending.
2 Do a magnetic particle inspection in accordance with section 42 of the Standard
Practices Manual 32-09-01 or to ASTM E1444.
3 Apply the protection (refer to REPAIR 8 section).
SUBTASK 32-41-81-320-011-A01
(4) Repair the splines with a maximum damage depth of 1,6 mm (0.063 in) by a weld repair
(Ref. Fig. 6010)
(a) Prepare damaged areas for build-up.
– Machine areas to be built-up following the instruction of (Ref. Fig. 6010).
– Deburr areas prepared for built-up.
– Make sure that there is no sharp edge on the cuts-out.
– The depth of the cuts-out must not be more than 1,6 mm (0.063 in).
– The length of the cuts-out must not be more than 25,4 mm (1.00 in).
NOTE: The number of cuts-out per spline is not restricted.
(b) Clean the torque plate (1-425) (refer to the CLEANING section).
CAUTION: KEEP THE PART AT THE CORRECT TEMPERATURE DURING THE WELD
PROCEDURE. INCORRECT TEMPERATURE CAN CAUSE DAMAGE TO
THE PART OR CAUSE THE WELD TO BREAK.
(c) Pre-heat integral torque plate (1-425) at a temperature between 204 and 260 °C (400
and 500 °F).
NOTE: Keep the temperature of the part between 204 and 315 °C (400 and 600 °F)
during welding.
NOTE: Deposit sufficient filler metal to make sure that the part can be machined to
the correct dimensions.
(d) Built-up the material by argon welding with the below requirements:
– AC or DC 50A current.
– 1,6 mm (0.063 in) diameter tungsten electrode.
– Argon torch spray rate: 9 l/min (2.37 US.gal/min).
REPAIR No. 6
Page 6038
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
– 1,6 or 2 mm (0.063 or 0.079 in) diameter BMS metal filler. The harness number of the
deposited BMS metal is equal to that of the torque plate.
(e) Weld with a shielded metal arc weld (stick electrode) or gas tungsten arc weld (TIG or
Heli-arc) or gas metal arc weld (MIG) procedure. Use a “low hydrogen” electrode or filler
metal that is 17-22A(S) alloy (AMS6458) or equivalent.
NOTE: Do not let dirt or moisture on the electrode or filler metal. Do not allow a
long arc which can let atmospheric contamination of the weld metal. Deposit
sufficient filler metal to make sure that the part can be machined to the correct
dimensions.
(f) Apply the built-up material consecutive runs overlapping on each side to prevent too
high or heat rise, while reworking.
(g) Immediately after welding place the torque plate in an oven at 500 °C (932 °F) for one
hour.
NOTE: Keep each part on its back leg end and do not stack parts.
(h) Stop heating and allow the torque plate to slowly cool inside oven.
(i) Machine the torque plate splines to the initial dimensions, (Ref. Fig. 6010).
(j) If the deposit is on the temperature sensor spline hole, restore the hole by drilling the
deposit: Ø 8,0 mm (0.315 in) hole at the same location (Ref. Fig. 6010).
(l) Do a magnetic particle inspection. Refer to the section 42 of the Standard Practices
Manual 32-09-01 or to ASTM E1444.
(m) Check roundness of the torque plate, a maximum of 0,25 mm (0.0098 in) is permitted
in the plane of replaced areas.
REPAIR No. 6
Page 6039
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR No. 6
Page 6041
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-320-012-A01
(5) Repair of the threaded hole(s) in the torque plate (1-425)
(a) Repair the damaged areas of threads with a standard Heli-Coil insert as follows:
2 Drill the threaded hole to 16,27 mm (0.641 in) diameter thru and perpendicular to the
end surface of the torque plate to a limit of 0.5° or less.
3 Counter bore the hole between 19,00 to 19,05 mm (0.748 to 0.750 in) diameter and
5,71 to 6,22 mm (0.2248 to 0.2449 in) depth.
4 Cut new threads to the full length of the hole with a Heli-Coil tap (18193-10). Tap the
hole perpendicular to the end surface of the torque plate to a limit of 0.5° or less.
5 Install a new Heli-Coil insert (1191-10CN 0625) with a Heli-Coil insert tool (535-10)
until the top coil is 0.5 - 1 turn below the surface. Break off the drive tang of the
Heli-Coil insert.
6 Press the bushing into the counterbore until the bushing is flush with the surface or
below the surface of the torque plate flange.
7 Impression stamp an “O” adjacent to the repaired hole. Remove metal that is raised
by the impression stamp.
REPAIR No. 6
Page 6042
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR No. 6
Page 6043
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-320-013-A010
(6) Repair of the torque plate diameter at the bushing assembly (1-428) location
(a) Machine the torque plate diameter at the bushing assembly (1-428) location to initial
manufacturing dimensions shown in (Ref. Fig. 6012).
(b) Make sure that the thickness “T” after the repair is not less than 3 mm (0.118 in).
REPAIR No. 6
Page 6044
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Machining dimensions for Torque Plate diameter at Bushing Assembly (1-428) location
FIGURE 6012/GRAPHIC32-41-81-991-030-A01
REPAIR No. 6
Page 6045
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR No. 6
Page 6046
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR 7
TASK 32-41-81-300-808-A01
1. Repair 7- Repair of the Cable Guide (1-275)
(2) Consumables
Not applicable.
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
(Exploded view)
C. Job set-up
Not applicable.
D. Procedure
(Ref. Fig. IPL 01)
SUBTASK 32-41-81-320-014-A01
(1) Repair of the cable guide (1-275) broken at the location, where the loop is welded together
during manufacturing
REPAIR No. 7
Page 6047
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR No. 7
Page 6048
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR 8
TASK 32-41-81-300-809-A01
1. Repair 8 - Protection
Not applicable.
(2) Consumables
Not applicable.
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
(Exploded view)
Standard Practices Manual 32-09-01, section Local repair of the surface finish on aluminium
14 alloys by chemical oxidizing
Standard Practices Manual 32-09-01, sections Painting
36C and 61A
Standard Practices Manual 32-09-01, section Sulphuric acid anodizing
11
Standard Practices Manual 32-09-01, sections Cadmium plating
3 and 15
SUBTASK 32-41-81-750-001-A01 Ground continuity test
C. Job set-up
Not applicable.
REPAIR No. 8
Page 6049
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
D. Procedure
(Ref. Fig. IPL 01)
WARNING : MAKE SURE YOU OBEY ALL THE HEALTH AND SAFETY PRECAUTIONS OF
THE MANUFACTURERS OF MATERIALS.
SUBTASK 32-41-81-380-001-A01
(1) Protection of the piston housing (1-020)
(a) Touch-up:
(b) To apply the modifications introduced by SB 2-1577-32-12, refer to the steps that follow:
1 Mask around the area where the temperature sensor assembly (1-250) touches the
piston housing (1-020) (Ref. Fig. 6013).
2 Remove the paint and primer from the area where the temperature sensor assembly
(1-250) touches the piston housing (1-020). Refer to the CLEANING section (Ref.
Fig. 6013).
3 Remove the anodize film from the area where the temperature sensor touches the
piston housing with #320 grit abrasive cloth. Use #400 grit (or finer) to smooth the
surface
4 Apply chemical oxidizer to locally repair the protection of the piston housing (1-020)
(refer to the section 14 of the Standard Practices Manual 32-09-01).
5 Do a ground continuity test (Ref. SUBTASK 32-41-81-750-001-A01).
1 Apply the full paint scheme as shown (Ref. Fig. 6013). Refer to the section 36C of
the Standard Practices Manual 32-09-01.
SUBTASK 32-41-81-380-002-A01
(2) Protection of the torque plate (1-425)
(a) Touch-up:
– Apply coating, use brush or spray techniques. A dry thickness of 0,012 to 0,025
mm (0.00047 to 0.00098 in) is recommended.
– The coating will air dry to allow handling in 30 minutes. Complete cure at ambient
temperature requires ten days. To accelerate curing insert into 120 °C (250 °F) air
circulating oven for four hours.
– Suppliers:
SERMATECH INTERNATIONAL INC.
155 South LIMERICK Road
LIMERICK PA 19468
U.S.A.
http://www.sermatech.com
or
SERMATECH INTERNATIONAL INC.
Weilenburgstrasse 49
42579 Heiligenhaus
GERMANY
http://www.sermatech.com
2 Apply the full paint scheme as shown (Ref. Fig. 6013). Refer to the section 61A of
the Standard Practices Manual 32-09-01 or Sermetel 2F-1 or contact SermaTech
International for instructions to return the torque plate for surface treatment
application.
SUBTASK 32-41-81-380-003-A01
(3) Protection of the piston sleeve (1-060)
(a) Touch-up:
REPAIR No. 8
Page 6051
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-380-004-A01
(4) Protection of the pin retainer (1-105)
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Touch-up:
1 If necessary, remove the temporary protection (refer to the CLEANING section). The
pin retainer (1-105) can be cadmium plated.
2 Apply cadmium plating. Refer to the section 3 of the Standard Practices Manual
32-09-01.
REPAIR No. 8
Page 6052
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR No. 8
Page 6053
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR No. 8
Page 6054
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-380-005-A01
(5) EDL® Return Policy for heat sink Repair
– Refer to SL 1701 for Airline/brake repair Station which currently deal with Messier-Goodrich
S.A. (FRANCE).
– Refer to SL 1685 for Airline/brake repair Station which currently deal with Goodrich-Messier
Inc. (U.S.A.).
REPAIR No. 8
Page 6055
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
REPAIR No. 8
Page 6056
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
ASSEMBLY
TASK 32-41-81-400-801-A01
1. Assembly
(2) Consumables
Page 7001
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(a) The table below gives the consumables necessary to assemble the component.
NOTE: You can use alternatives for the listed items.
REFERENCE NAME
Commercially available Clean and soft lint-free cloth
REFERENCE DESIGNATION
ILLUSTRATED PARTS LIST, Fig. IPL 01 Main Landing Gear Carbon Brake Assembly
(Exploded view)
Standard Practices Manual 32-09-01, section Bonding of mating parts with ARALDITE
27
C. Job set-up
Not applicable.
D. Procedure
(Ref. Fig. IPL 01)
Page 7002
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
CAUTION: MAKE SURE THAT ALL THE PARTS ARE CLEAN BEFORE ASSEMBLY.
SUBTASK 32-41-81-400-001-A01
(1) First steps
Page 7003
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-440-002-A01
(2) Assembly of the piston (1-070)
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Installation of the preformed packings on the piston (1-070):
1 Install the back-up rings (1-075) on the piston (1-070) with the cone and the plunger
for the tool AC21869000.
2 Install the half-washers of the tool AC21869000 on the piston (1-070).
3 Install the resizing ring of the tool AC21869000 (on the side of the larger chamfer) and
hold the half-washers in position. Leave the resizing ring in position for two hours.
NOTE: When installed properly, the resizing ring will rotate freely on the piston
(1-070).
4 Remove the resizing ring and the half-washers of the tool AC21869000 from the
piston (1-070).
5 Put the back-up rings (1-075) in position against the shoulders on the piston.
6 Install the preformed packing (1-080) on the piston (1-070) with the tool 89901.
Page 7004
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(b) Installation of the preformed packings and the scraper ring assembly (1-065) on the
piston sleeve (1-060):
1 Before SB 2-1577-32-13:
a Install the back-up rings (1-163) on the piston sleeve (1-060) with the cone and
the plunger of the tool AC21868010.
b Install the half-washers of the tool AC21868010 on the piston sleeve (1-060).
c Install the resizing ring of the tool AC21868010 (on side of the larger chamfer) and
hold the half-washers in position. Leave the resizing ring in position for two hours.
NOTE: When installed properly, the resizing ring will rotate freely on the piston
sleeve (1-060).
d Remove the resizing ring and the half-washers of the tool AC21868010 from the
piston sleeve (1-060).
e Put the back-up rings (1-163) in position against the shoulders on the piston
sleeve (1-060).
f Install one preformed packing (1-045) on the piston sleeve (1-060) with the cone
of the tool AC21868010.
2 After SB 2-1577-32-13:
a Install two preformed packings (1-045) on the piston sleeve (1-060) with the
cone of the tool AC21868010.
3 Install the scraper ring assembly (1-065) in the piston sleeve (1-060) with the tool
89901.
NOTE: Bend the scraper ring assembly (1-065) without damage to the part to
ease its installation. The scraper ring assembly (1-065) can be heated
to be softer for installation.
(c) Install the spring (1-125), the guide sleeve (1-120) and the spring guide (1-115) in the
piston (1-070).
NOTE: Make sure that the spring (1-125) is fully against the bottom of the piston
(1-070) and that its position is correct.
CAUTION: IF THE RETAINING RING (1-130) HAS ONE OF ITS OUTER EDGES LIGHTLY
ROUNDED, INSTALL IT IN SUCH A POSITION THAT THIS ROUNDED EDGE
DOES NOT HOLD THE LOAD.
(d) Compress the spring (1-125) with the tool Q46498 enough to access the second groove
of the piston (1-070).
(e) Install the retaining ring (1-130) into this groove.
Page 7005
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(f) Slowly release the force applied to the spring (1-125). Remove the tool Q46498.
(g) Install the back-up rings (1-085) and the preformed packing (1-090) on the piston (1-070).
(i) Install the retaining ring (1-100) in its groove on the piston.
(j) Install the pin retainer (1-105) on the adjuster pin (1-110). The pin retainer (1-105) can
be cadmium plated. Install the tool Q46500 on the adjuster pin (1-110).
(k) Apply hydraulic fluid on the adjuster pin (1-110) and on the tool Q46500.
(l) Install the adjuster pin (1-110) in the piston (1-070) with the tool Q46500, so as not to
cause damage to the back-up rings (1-085) and preformed packing (1-090).
(o) Apply hydraulic fluid on the external diameter of the piston (1-070), on the preformed
packing (1-080) and on the tool Q46676.
(p) Install the piston (1-070), together with its components, into the piston sleeve (1-060).
Use the tool 114-552 and 114-1097 (optional) (Ref. Fig. 9014). Remove the tool Q46676.
(q) Install the new adjuster tube (1-140) on the adjuster pin (1-110).
(r) Install the ball (1-145) and the self locking-nut (1-150), with the self-locking nut (1-150)
against the flat side of the ball (1-145). The self locking-nut (1-150) can be cadmium
plated.
(s) Torque the self-locking nut (1-150) to a load of between 7,3 and 8,5 N.m (65 and 75
lbf.in). The self locking-nut (1-150) can be cadmium plated.
(t) Install the instruction plate (1-135) in the piston (1-070) (lettering up) against the retaining
ring (1-130).
(u) Install the new retaining ring (1-160) in the piston (1-070).
(v) Install the insulator assembly (1-155) in the piston (1-070). Push the insulator assembly
(1-155) until the retaining ring (1-160) is in its insulator groove.
SUBTASK 32-41-81-440-003-A01
(3) Assembly of the housing and adjuster piston assembly (1-010)
Page 7006
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Install a preformed packing (1-210B) on each valve (1-200) with the tool 89901.
(b) Apply hydraulic fluid to the threads of the bleeder valves (1-200) and on the preformed
packings (1-210B).
(c) Install the valves (1-200) on the housing and adjuster piston assembly (1-010).
(d) Torque the valves (1-200) to a load of between 13 and 15 N.m (9.6 and 11.06 lbf.ft).
(e) Torque the body assembly (1-205) of each valve (1-200) to a load of between 5,65
and 8,47 N.m (50 and 75 lbf.in).
(g) Torque the protective cap (1-215) of each valve (1-200) to a load of between 0,8 and
1,1 N.m (7 and 10 lbf.in).
(h) Install:
– Before SB 2-1577-32-4: the lubrication fittings (1-040) and torque it to a load of
between 2,8 and 5,1 N.m (25 and 45 lbf.in).
– After SB 2-1577-32-4: the lubrication fittings (1-040) and (1-043) and torque it to a
load of between of 2,8 and 5,1 N.m (25 and 45 lbf.in).
(i) Install a preformed packing (1-225) on the each hydraulic fitting assembly (1-230) with
the tool 89901.
(j) Apply hydraulic fluid to the threads of the hydraulic fitting assemblies (1-230) and on
the preformed packings (1-225).
(k) Install the hydraulic fitting assemblies (1-230) on the housing and adjuster piston
assembly (1-010).
(l) Torque the hydraulic fitting assemblies (1-230) to a load of between 17 and 19 N.m
(12.5 and 14.01 lbf.ft)
Page 7007
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(m) Install a protective cap (1-231) on each hydraulic fitting assembly (1-230).
NOTE: Put the cable bracket assembly (1-290) and the cable guide (1-275) in their
correct position on the brake, during installation on the aircraft. You will then
torque and lock the screws (1-285) and (1-325) during this procedure.
(n) Install the cable bracket assembly (1-290) with washers (1-320) and screw (1-325). The
washers (1-320) can be cadmium plated.
(o) Torque the screw (1-325) to a load of between 4,5 and 5,1 N.m (40 and 45 lbf.in).
(p) Install the cable guide (1-275) with the washers (1-280) and the screws (1-285). The
washer (1-280) can be cadmium plated.
(q) Torque the screw (1-285) to a load of between 4,5 and 5,1 N.m (40 and 45 lbf.in).
(r) Apply antiseize compound AMS-2518 or MIL-T-5544 to the load-bearing areas and
threads of the bolt (1-185), the washer (1-180) and the nut (1-190) (Ref. Fig. 7001). The
bolt (1-185), the washer (1-180) and the nut (1-190) can be cadmium plated.
(s) Install the torque pin (1-170) and the collar (1-175). The collar (1-175) can be cadmium
plated.
(t) Install the bolt (1-185), the washer (1-180) and the nut (1-190). Do not tighten this the
nut. The bolt (1-185), the washer (1-180) and the nut (1-190) can be cadmium plated.
NOTE: You will tighten and lock the nut on installation on aircraft. Torque the nut to a
load of between 12 and 13 N.m (8.85 and 9.6 lbf.ft). If the castelled nut does
not align with the hole in the bolt, move the nut to the next slot.
Install the cotter pin (1-195) which will be bent over after installation on aircraft.
(u) Installation of the adjuster assemblies (1-055)
1 Before SB 2-1577-32-13:
a Apply hydraulic fluid only to the preformed packing (1-045) and to the threads
of the piston sleeve (1-060).
b Install the adjuster assemblies (1-055A) with the tool Q47621.
c Torque the adjuster assemblies (1-055A) to a load of between 55 and 60 N.m
(40.6 and 44.2 lbf.ft).
2 After SB 2-1577-32-13:
a Apply hydraulic fluid to the two preformed packings (1-045) and to the threads
of the piston sleeve (1-060).
b Install the adjuster assemblies (1-055B) with the tool Q47621.
NOTE: Make sure that each preformed packing is not pinched and damaged
as it enters the piston housing.
Page 7008
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
(w) Installation of the identification plate (1-480) and the instruction plate (1-485):
1 Write on the new plates (1-480) and (1-485) all the data shown on the old plates.
If necessary, add the new identification and amendment data to agree with the
overhaul of the component.
2 Make rough the painted surface on the piston housing where you will install the
plates. Do not remove the paint layer.
3 Clean the areas on the housing and adjuster piston assembly (1-010) where you will
install the plates (1-480) and (1-485) with cleaning product.
NOTE: Refer to figures in the Illustrated Parts List (IPL) to know the locations of
the identification plate (1-480) and the instruction plate (1-485).
5 Bond the identification plate (1-480) and the instruction plate (1-485) on the housing
and adjuster piston assembly (1-010) with adhesive compound. Refer to the section
27 of the Standard Practices Manual 32-09-01.
(y) Protection of the identification plate (1-480) and of the instruction plate (1-485):
Page 7009
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 7010
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-440-004-A01
(4) Assembly of the torque plate assembly (1-420)
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Assemble the bushings (1-430) and (1-435) with the tool AC21867000.
(b) Install the bushing assembly (1-428) on to the torque plate (1-425) with tool AC21866000.
(d) Put the heat shield assembly (1-445) in position at the rear of the torque plate (1-425).
(e) Attach the heat shield assembly (1-445) with one of the following methods.
Method 1:
1 Install the bolts (1-455) and the washers (1-450). The bolts (1-455) and the washers
(1-450) can be cadmium plated.
Method 2:
2 Install the bolts (1-455), the washers (1-450) and (1-462) and the nuts (1-461). The
bolts (1-455), the washers (1-450) and the nuts (1-461) can be cadmium plated.
(f) Torque the bolts (1-455) or the nuts (1-461) to a load of between 4,5 and 5,1 N.m (40 and
45 lbf.in). The bolts (1-455) and the nuts (1-461) can be cadmium plated.
Page 7011
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-410-004-A01
(5) Installation of the heat sink
(Ref. Fig. 7002)
(Ref. Fig. 7003)
(Ref. Fig. 7004)
(Ref. Fig. 7005)
CAUTION: THE CARBON DISKS ARE BREAKABLE. DO NOT LET THEM FALL OR HIT
HARD OBJECTS. IF THEY ARE DAMAGED, EXAMINE THEM AS WRITTEN
IN THE CHECK SECTION.
CAUTION: WHEN YOU INSTALL THE HEAT SINK, DO NOT LET THE CARBON DISKS
TOUCH THE MATERIALS THAT FOLLOW:
– STRIPPERS.
– GREASE OR OIL.
– PAINTS (THERMOCOLOR, MARKING OR RED LEAD TYPES).
– CHALK.
– HYDRAULIC FLUID.
CAUTION: ON THE ASSEMBLY OF A HEAT SINK NOT FULLY WORN, ALL PARTS
MUST BE ASSEMBLED REFERRING TO THE MARKS MADE DURING
DISASSEMBLY (REFER TO THE DISASSEMBLY SECTION).
NOTE: When you install a heat sink, you must (Ref. Fig. 7002, Ref. Fig. 7003 and ,
Ref. Fig. 7004) which give approved configuration for new heat sinks as well as
overhauled ones.
NOTE: Heat sink (new or overhauled) total thickness is given in (Ref. Fig. 7002, Ref.
Fig. 7003 and , Ref. Fig. 7004) .
NOTE: For the multiple disk brakes (1-001A) and (1-001B) the use of overhauled
”Second-run” disks at overhaul causes the brake assembly P/N to change from
OPT2 to OPT1 or from OPT1 to OPT2, but without the need to identify the
assembly again each time.
(a) Assembly of the end plate disk assembly (1-390) and the torque plate assembly (1-420)
Page 7012
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
1 Install the end plate disk assembly (1-390) on the torque plate assembly (1-420). Put
the torque buttons (1-400) fully home in the torque plate.
2 Install the four clips (1-410) in such a position that they are aligned with the four
slots in the torque plate assembly (1-420).
3 Bend the end of the clips (1-410) as shown on (Ref. Fig. 7005).
(b) Install the rotor disk assembly (1-360) and the stator disks (1-385) one after the other on
the torque plate assembly (1-420) (Ref. Fig. 7002, Ref. Fig. 7003 and , Ref. Fig. 7004) .
NOTE: The stator disk (1-385) and the pressure plate assembly (1-340) have one
larger drive slot which engages the wide lug of the torque plate assembly
(1-420).
(c) Install the pressure plate assembly (1-340) so that inserts face up.
(d) Install the two wear indicator pins (1-265) and the retaining clips (1-270) in the inserts on
the pressure plate assembly (1-340) ((Ref. Fig. 7006), Detail C).
(e) Install the heat shield assembly (1-415) so that the two external tabs will engage vent
slots in the torque plate.
Page 7013
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 7014
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 7015
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 7016
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 7017
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-440-005-A02
(6) Assembly of the housing and adjuster piston assembly (1-010) with the torque plate / heat
sink assembly
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Put the housing and adjuster piston assembly (1-010) in position on the torque plate
assembly (1-420).
(b) Align the hole for the temperature sensor assembly (1-250) with the hole in the wide
spline of the torque plate.
(c) Guide the wear indicator pins (1-265) through holes in the piston housing.
(e) Install the washers (1-470) and the bolts (1-465) (Tighten the bolts in criss-cross
sequence). The washers (1-470) can be cadmium plated. Torque the bolts:
– To a load of between 198 and 209 N.m (146 and 154 lbf.ft) when SAE-AMS2518 or
MIL-T-5544 anti-seize compound applied.
or
– To a load of 175 N.m (129.1 lbf.ft) when MIL-PRF-83483 antiseize compound applied.
NOTE: It is recommended to do a check of the torque load in a circular sequence
to correct any possible omission.
Page 7018
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
SUBTASK 32-41-81-410-005-A01
(7) Installation of the temperature sensor assembly (1-250)
The Occupational, Safety, and Health Administration (OSHA) has an applicable DANGER
warning (29 CFR 1910.1027 (m)(3)(ii)) as follows:
DANGER: CONTAINS CADMIUM. CANCER HAZARD. AVOID CREATING DUST. CAN CAUSE
LUNG AND KIDNEY DISEASE.
(a) Put the temperature sensor assembly (1-250) in position, with the protective cap installed
on it.
(b) Install the washer (1-255) and the screw (1-260). Torque the screw (1-260) to a load of
between 4,5 and 5,1 N.m (40 and 45 lbf.in). The washer (1-255) can be cadmium plated.
SUBTASK 32-41-81-400-002-A01
(8) Last steps
(Ref. Fig. 7006)
(a) Do the tests as written in the TESTING AND FAULT ISOLATION section.
(c) Safetying:
Page 7019
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Safetying
FIGURE 7006/GRAPHIC32-41-81-991-038-A01
Page 7020
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TASK 32-41-81-820-801-A01
1. Fits and Clearances
A. General
(1) For all the parts of a selective fit assembly or parts to which time can cause damage or
wear, the table below gives:
(a) The manufacturing tolerances for the parts which are new.
(b) The maximum wear and the limits to send the component back to service, for the parts
which are not new.
(2) It is highly recommended to give the parts their initial condition (as new) during the major
overhaul. To do this, repair the parts as written in the REPAIR section or replace them
as necessary.
(3) The worn dimensions or the fits may be revised as experience is gained during the ageing
analysis or the performance of the parts.
B. Layout
(1) First column:
Gives the location on the figure(s) of the clearance, fit, or dimension that you must measure.
Gives the figure and item numbers shown in the Illustrated Parts List (IPL).
ID: INSIDE DIAMETER.
OD: OUTSIDE DIAMETER.
Gives the clearance (letter J) or interference fit (letter S), which is the result of the manufacturing
tolerances.
Give the permitted dimension limits to send the component back to service as it is.
Gives the permitted wear limit to send the component back to service as it is.
Page 8001
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 8002
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Location of Fits
FIGURE 8001/GRAPHIC32-41-81-991-039-A01
Page 8003
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TASK 32-41-81-820-802-A01
2. Torque values
A. General
(1) This section gives the values for the torque values as applicable.
CAUTION: APPLY THE PRODUCT AND THE TORQUE AS WRITTEN IN THE ASSEMBLY
SECTION. IF NOT, THIS CAN CAUSE DAMAGE TO THE PARTS.
IPL FIG-ITEM
NAME TORQUE VALUE PRODUCT REQUIRED
NO.
(1-040) Lubrication fitting 2,8 to 5,1 N.m (25 to 45 lbf.in) Not applicable
(1-043) Lubrication fitting 2,8 to 5,1 N.m (25 to 45 lbf.in) Not applicable
(1-055) Adjuster assembly 55 to 60 N.m (40.6 to 44.2 lbf.ft) Not applicable
(1-150) Self-locking nut 7,3 to 8,5 N.m (65 to 75 lbf.in) Not applicable
(1-190) Nut (For information 12 to 13 N.m (8.85 to 9.6 lbf.ft)
SAE-AMS2518 or
only: tightened on
MIL-T-5544
aircraft)
(1-200) Valve 13 to 15 N.m (9.6 to 11.1 lbf.ft) Not applicable
(1-205) Body assembly 5,6 to 8,5 N.m (50 to 75 lbf.in) Not applicable
(1-215) Protective cap 0,8 to 1,1 N.m (7 to 10 lbf.in) Not applicable
(1-230) Hydraulic fitting 17 to 19 N.m (12.5 to 14.01 lbf.ft)
Not applicable
assembly
(1-260) Screw 4,5 to 5,1 N.m (40 to 45 lbf.in) Not applicable
(1-285), Screw (For information 4,5 to 5,1 N.m (40 to 45 lbf.in)
(1-325) only: tightened on Not applicable
aircraft)
(1-455) Bolt 4,5 to 5,1 N.m (40 to 45 lbf.in) Not applicable
(1-465) Bolt 198 to 209 N.m (146 to 154 lbf.ft) SAE-AMS-2518 OR
MIL-T-5544
175 N.m (129 lbf.ft) MIL-PRF- 83483
Page 8004
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TASK 32-41-81-940-801-A01
1. Special Tools, Fixtures and Equipment
A. General
NOTE: Standard tools and equipment, usually available at overhaul, can be used to service
the carbon brake, but not for the special tools and fixtures listed below. You can use
alternatives for the listed items.
(1) Special tools and fixtures are available from Messier-Services (CAGE FAJX6). Inquire at the
following address for the price and delivery time:
Messier-Services
Attn.: Turn Key Services Dept.
36, avenue de l’Europe
78147 VELIZY Cedex
France
Telephone: 33 (0) 1 30 67 45 28
Fax: 33 (0) 1 30 67 45 95
NOTE: These special tools are not available from Goodrich Corporation. Alternate
drawings (114-part numbers) are given in this section to locally make special
tools.
Page 9001
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9002
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9003
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9004
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9005
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9006
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9007
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9008
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9009
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9010
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9011
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9012
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9013
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9014
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9015
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9016
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9017
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9018
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9019
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9020
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9021
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9022
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Adapter Q47621
FIGURE 9009/GRAPHIC32-41-81-991-048-A01
Page 9023
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9024
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9025
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9026
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9027
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Spatula 89901
FIGURE 9012/GRAPHIC32-41-81-991-051-A01
Page 9028
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9029
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9030
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9031
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TASK 32-41-81-940-802-A01
2. Aqueous Cleaner Consumables
Page 9032
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9033
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9034
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TASK 32-41-81-940-803-A01
3. Other Consumables
Page 9035
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 9036
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TASK 32-41-81-550-801-A01
1. Storage Instructions
Not applicable.
(2) Consumables
Not applicable.
REFERENCE DESIGNATION
Standard Practices Manual 32-09-01, section Storage
72
C. Job set-up
Not applicable.
D. Procedure
SUBTASK 32-41-81-550-001-A01
(1) Storage
Page 15001
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 15002
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
TASK 32-41-81-871-802-A01
1. Introduction to the Illustrated Parts List
A. Policy
(1) This section is the list of all the parts of the component which are given in this manual, and
makes it possible to identify these parts. It contains, as indexes, Illustrated Parts List, etc., all
the data necessary to get of all the parts.
Page 10001
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
5 The EFFECTIVITY CODE column shows the Item Number of the next higher
assembly or sub-assembly. For items used in the full range of the primary component,
the EFFECTIVITY CODE column is kept blank. This column is also kept blank for
assemblies located on a line which is not indented (line 1).
6 The "UNITS PER ASSY" column shows the quantity per assembly which is
necessary for the next higher assembly. In the indexes, the quantity shown refers to
the quantity broken down for a given CSN.
C. Revision
(1) When a line is new, modified or deleted, there is a letter "R" or a vertical black line at the end
of the line (the date of issue is changed).
(2) After each modification of a given item, the numerical Item Number itself does not change.
But the variant letter changes from "A" to "B", then to "C" thru "Z" (do not use letters "I"
and "O").
(3) When it is necessary to add a new part, its name must be on the line which agrees with
the correct position of this part in the breakdown of the assembly. Select its Item Number
from open sequences.
(a) When the layout of the basic figure does not make it possible to show new parts or the
new shape of modified parts, a new figure (called "figure variant") is then added.
(b) This figure variant will have the same number as that of the basic figure, followed by a
letter given in alphabetical sequence (do not use "I" and "O").
(b) If these two conditions are satisfied, identify the deleted items, in the nomenclature
column, by the word: "DELETED".
(c) The Part Number of the deleted part is then kept in the indexes with the word "DELETED".
Page 10002
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
D. General
(1) There is a breakdown of assemblies and each part is shown in the assembly sequence.
(2) The vertical lines of the indention are shown as dotted lines as follows:
1 2 3 4 5 6 7 (Indention number)
Assembly
. Part of the assembly
. Sub-assembly
. . Part of the sub-assembly
. . . Detail part
(3) This sequence is, in fact, changed by the nomenclature of the attaching parts and storage
parts. The attaching parts are shown immediately below the assembly or sub-assembly they
attach, and above the detail parts.
(4) The storage parts are shown immediately below the parts on which they are installed for
protection.
(a) Indented in line with the assembly, sub-assembly or part to which they are related.
(b) Identified by the words "ATTACHING PARTS" or "STORAGE PARTS" shown on the
line above.
(c) Followed by three stars shown on the line below.
Page 10003
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
RF For reference
SB Service Bulletin
SEL FROM "Select from" parts
OVERSIZE - UNDERSIZE "Oversize/undersize" parts
OPT Optional
ALT Alternate
SUPSD BY Superseded by
SUPSDS Supersedes
NHA Next Higher Assembly
DET Detail
LH and RH Left Hand and Right Hand
AR As required
NP Non procurable
ORDER OVERLGTH MPN Full P/N of the manufacturer
REPLACED BY Replaced by
REPLACES Replaces
Page 10004
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
VF9023 GREENE TWEED & CO FRANCE SAS 19 RUE DES BEAUX SOLEILS 95520 OSNY
FRANCE
VK2523 EATON AEROSPACE LTD ABBEY PARK, SOUTHAMPTON ROAD TITCHFIELD PO14
4QA FAREHAM-HAMPSHIRE UNITED KINGDOM
V51814 SMALLEY STEEL RING CO. 555 OAKWOOD RD 60047-1558 LAKE ZURICH IL U.S.A.
V56878 SPS TECHNOLOGIES LLC DBA AEROSPACE DIVISION DIV AEROSPACE PRODUCTS
301 HIGHLAND AVE 19046-2630 JENKINTOWN PA U.S.A.
V79136 TRUARC COMPANY LLC DBA WALDES TRUARC 125 BRONICO WY 08865-2778
PHILLIPSBURG NJ U.S.A.
V84256 AVIBANK MFG INC 11500 SHERMAN WAY 91605-5827 NORTH HOLLYWOOD CA U.S.A.
Page 10005
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 10006
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
A36369EB 01 031A 2
AC21910100 01 005A 1
AN3C5A 01 455A 3
AS15001-1C 01 040C 2
043C 2
AS15001-1P 01 040B 2
043B 2
BLS4R03N 01 310C 1
FN12M02 01 150A 14
GA56999-1 01 205A 2
HTE1001B7 01 234A 2
HTE711-218B 01 230A 2
HTE717B 01 231A 2
HTE7300E3-014 01 237A 2
HTE7300E3-018 01 233A 2
HTE760B3 01 232A 2
HTE761B8 01 236A 2
HTE762-135B8 01 238A 2
MS15001-1 01 040A 2
043A 2
MS16625-3125 01 100B 14
MS16625-4150 01 130B 14
NI/ALPH
Page 10007
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
MS17826-8 01 190A 1
MS20002C10 01 470A 14
MS20995C32 01 165A AR
220A AR
240A AR
330A AR
475A AR
MS21042-3 01 461A AR
MS21206C3 01 450A 3
MS24665-304 01 195A 1
MS51844-61 01 305A 2
N5000-125 01 100A 14
N5000-150H 01 130A 14
NAS1149C0363B 01 462A AR
NAS1149F0463P 01 255A 1
280A 4
320A 4
NAS1149F0863P 01 180A 1
NAS1351C4H10 01 260A 1
285A 4
325A 4
NAS1611-015 01 210B 2
NAS1611-015A 01 210C 2
NAS1612-6 01 210A 2
225A 2
NAS1612-6A 01 225B 2
NM10-2525TL 01 460A 3
S33865-19H10 01 065A 14
NI/ALPH
Page 10008
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
VS675S02 01 440A 1
107-382-7 01 055A 14
107-382-8 01 055B 14
113-150-1 01 115A 14
113-189 01 275A 1
1191-4CN0500 01 035A 9
1191-4CN500 01 035B 9
130-27 01 145A 14
133-1161-1 01 385A 4
133-1161-2 01 385B 4
133-1658-1 01 385C 4
385E 1
133-1658-2 01 385D 4
385F 1
134-429-1 01 340A 1
134-429-2 01 340B 1
134-430-1 01 360A 5
134-430-2 01 360B 5
134-431-1 01 390A 1
NI/ALPH
Page 10009
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
134-431-2 01 390B 1
134-768-1 01 385G 3
134-768-2 01 385H 3
134-806-1 01 340C 1
134-806-2 01 340D 1
134-866-1 01 360C 5
134-866-2 01 360D 5
134-867-1 01 390C 1
134-867-2 01 390D 1
148-552 01 295A 1
184-895-1 01 425A 1
184-895-2 01 425B 1
2-1577-1 01 001E RF
001F RF
2-1577-1OPT1 01 001A RF
2-1577-1OPT2 01 001B RF
2-1577-2 01 001G RF
2-1577-2OPT1 01 001C RF
2-1577-2OPT2 01 001D RF
2-1577-3 01 001H RF
2-1577-4 01 001J RF
2-1577-5 01 001K RF
2-1577-6 01 001L RF
2-1577-7 01 001M RF
NI/ALPH
Page 10010
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
2-1577-8 01 001N RF
2-1577-9 01 001P RF
20-629 01 110A 14
20-630 01 265A 2
20-678 01 170A 1
230-19 01 065D 14
23320CA080 01 165B AR
220B AR
240B AR
330B AR
475B AR
24-38 01 300A AR
25-147 01 175A 1
26-383-1 01 025A 1
26-384-1 01 030A 2
26-391 01 430A 1
26-392 01 435A 1
26-397 01 030B 2
26-400 01 025B 1
260-888 01 020A 1
260-888-1 01 020B 1
266-267 01 015A 1
266-267-2 01 015B 1
3201-04-03 01 310A 1
322-124 01 400A 12
322-124-1 01 400B 12
NI/ALPH
Page 10011
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
378-47-3 01 445A 1
378-48-1 01 415A 1
4-357 01 420A 1
40-666 01 125A 14
4186A19E0190 01 065C 14
43-1395 01 185A 1
43-1396 01 465A 14
437-50 01 155A 14
444-52 01 290A 1
45-231-1 01 140A 14
466-8 01 250A 1
50-598 01 135A 14
50-639 01 480A 1
50-640 01 485A 1
53-288 01 270A 2
53-321 01 160A 14
53-345 01 410A 4
53-411 01 160B 14
537-122-1 01 335E 1
537-122-2 01 335F 1
537-122-3 01 335G 1
537-122-4 01 335H 1
537-154-1 01 335C 1
NI/ALPH
Page 10012
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
537-154-2 01 335D 1
537-33-1 01 335A 1
537-33-2 01 335B 1
538-5 01 428A 1
54-471-1 01 060A 14
54-492-1 01 120A 14
544-13-1 01 010A 1
544-13-3 01 010B 1
544-13-4 01 010C 1
548-1 01 315A 1
549-70 01 163B 2
549-71 01 075B 28
549-72 01 085B 28
56-924 01 105A 14
56-951 01 095A 14
57539-1 01 310B 1
68-1357 01 080A 14
68-1358 01 075A 28
68-1359 01 163A 2
68-1360 01 045A 14
045B 28
68-1363 01 245A 1
NI/ALPH
Page 10013
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
68-1364 01 090A 14
68-1365 01 085A 28
68-1610 01 045C 14
74-861-3 01 070A 14
74-861-5 01 070B 14
7612 01 215A 2
78-291 01 395A 12
798A 01 200A 2
86978 01 065B 14
NI/ALPH
Page 10014
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 10015
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 10016
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 10017
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 10018
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 10019
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 10020
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 10021
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 10022
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 10023
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 10024
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 10025
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
Page 10026
32-41-81
The document is subject to the controls and restrictions on the first page.
Apr 26/11
COMPONENT MAINTENANCE MANUAL
2-1577 Series
01
–001A 2-1577-1OPT1 BRAKE, MULTIPLE DISK RF
REPLACED BY ITEM -001E
(NP)
–001B 2-1577-1OPT2 BRAKE, MULTIPLE DISK RF
REPLACED BY ITEM -001F
(NP)
–001C 2-1577-2OPT1 BRAKE, MULTIPLE DISK RF
REPLACED BY ITEM -001G
(NP)
POST SB 2-1577-32-4
–001D 2-1577-2OPT2 BRAKE, MULTIPLE DISK RF
REPLACED BY ITEM -001G
(NP)
POST SB 2-1577-32-4
–001E 2-1577-1 BRAKE, MULTIPLE DISK RF
(TRUE P/N 2-1577-1OPT1) REPLACES
ITEM -001A
(NP)
–001F 2-1577-1 BRAKE, MULTIPLE DISK RF
(TRUE P/N 2-1577-1OPT2) REPLACES
ITEM -001B
(NP)
–001G 2-1577-2 BRAKE, MULTIPLE DISK RF
REPLACES ITEMS -001C AND -001D
(NP)
POST SB 2-1577-32-4
–001H 2-1577-3 BRAKE, MULTIPLE DISK RF
(NP)
POST SB 2-1577-32-10
–001J 2-1577-4 BRAKE, MULTIPLE DISK RF
(NP)
POST SB 2-1577-32-10
–001K 2-1577-5 BRAKE, MULTIPLE DISK RF
(NP)
POST SB 2-1577-32-13
–001L 2-1577-6 BRAKE, MULTIPLE DISK RF
(NP)
POST SB 2-1577-32-13
–001M 2-1577-7 BRAKE, MULTIPLE DISK RF
(NP)
POST SB 2-1577-32-14
01
–001N 2-1577-8 BRAKE, MULTIPLE DISK RF
(NP)
POST SB 2-1577-32-14
–001P 2-1577-9 BRAKE, MULTIPLE DISK RF
POST SB 2-1577-32-14
005A AC21910100 . PROTECTOR 1
(FOR PRESERVATION ONLY)
–010A 544-13-1 . PISTON ASSEMBLY, HOUSING AND 1ABEF 1
ADJUSTER HM
(NP)
–010B 544-13-3 . PISTON ASSEMBLY, HOUSING AND 1CDGJ 1
ADJUSTER KN
(NP)
POST SB 2-1577-32-4
–010C 544-13-4 . PISTON ASSEMBLY, HOUSING AND 1LP 1
ADJUSTER
(NP)
POST SB 2-1577-32-13
–015A 266-267 . . HOUSING ASSEMBLY, PISTON 10A 1
(NP)
–015B 266-267-2 . . HOUSING ASSEMBLY, PISTON 10BC 1
POST SB 2-1577-32-4
–020A 260-888 . . . HOUSING, PISTON 15A 1
(NP)
020B 260-888-1 . . . HOUSING, PISTON 15B 1
(NP)
POST SB 2-1577-32-4
–025A 26-383-1 . . . BUSHING, HUB 1
PART CAN BE CADMIUM PLATED
(NP)
OPT TO 26-400 (VF6137)
025B 26-400 . . . BUSHING, HUB 1
PART CAN BE CADMIUM PLATED
OPT TO 26-383-1 (VF6137)
–030A 26-384-1 . . . BUSHING, TORQUE ARM 2
PART CAN BE CADMIUM PLATED
(NP)
OPT TO 26-397 (VF6137)
030B 26-397 . . . BUSHING, TORQUE ARM 2
PART CAN BE CADMIUM PLATED
OPT TO 26-384-1 (VF6137)
030C A36369EB . . . DELETED
01
–031A A36369EB . . . BUSHING, TORQUE ARM 2
REPAIR ONLY
–035A 1191-4CN0500 . . . INSERT, THREAD (V01556) 15A 9
(NP)
–035B 1191-4CN500 . . . INSERT, THREAD (V01556) 15B 9
040A MS15001-1 . . . FITTING, LUBRICATION 2
040B AS15001-1P . . . FITTING, LUBRICATION 15B 2
040C AS15001-1C . . . FITTING, LUBRICATION 15B 2
PART CAN BE CADMIUM PLATED
(NP)
043A MS15001-1 . . . FITTING, LUBRICATION 15B 2
POST SB 2-1577-32-4
043B AS15001-1P . . . FITTING, LUBRICATION 2
043C AS15001-1C . . . FITTING, LUBRICATION 2
PART CAN BE CADMIUM PLATED
(NP)
045A 68-1360 . . PACKING, PREFORMED 10AB 14
PRE SB 2-1577-32-13
045B 68-1360 . . PACKING, PREFORMED 10C 28
POST SB 2-1577-32-13
045C 68-1610 . . PACKING, PREFORMED 10B 14
(NP)
POST SB 2-1577-32-13
050A 68-1359 . . DELETED
050B 549-70 . . DELETED
POST SB 2-1577-32-11
055A 107-382-7 . . ADJUSTER ASSEMBLY 10AB 14
(NP)
055B 107-382-8 . . ADJUSTER ASSEMBLY 10C 14
POST SB 2-1577-32-13
060A 54-471-1 . . . SLEEVE, PISTON 1
065A S33865-19H10 . . . RING ASSEMBLY, SCRAPER 1
(V09257)
(NP)
OPT TO 86978 (VF9023)
OPT TO 230-19 (VF6137)
OPT TO 4186A19E0190 (VF9023)
01
065B 86978 . . . RING ASSEMBLY, SCRAPER 1
(VF9023)
OPT TO S33865-19H10 (V09257)
OPT TO 230-19 (VF6137)
OPT TO 4186A19E0190 (VF9023)
065C 4186A19E0190 . . . RING ASSEMBLY, SCRAPER 1
(VF9023)
OPT TO S33865-19H10 (V09257)
OPT TO 230-19 (VF6137)
OPT TO 86978 (VF9023)
065D 230-19 . . . RING ASSEMBLY, SCRAPER 1
(NP)
OPT TO S33865-19H10 (V09257)
OPT TO 4186A19E0190 (VF9023)
OPT TO 86978 (VF9023)
070A 74-861-3 . . . PISTON 1
(NP)
070B 74-861-5 . . . PISTON 1
–075A 68-1358 . . . RING, BACK-UP 2
(NP)
075B 549-71 . . . RING, BACK-UP 2
POST SB 2-1577-32-11
080A 68-1357 . . . PACKING, PREFORMED 1
–085A 68-1365 . . . RING, BACK-UP 2
(NP)
085B 549-72 . . . RING, BACK-UP 2
POST SB 2-1577-32-11
090A 68-1364 . . . PACKING, PREFORMED 1
095A 56-951 . . . RETAINER, SEAL 1
–100A N5000-125 . . . RING, RETAINING (V79136) 1
100B MS16625-3125 . . . RING, RETAINING 1
105A 56-924 . . . RETAINER, PIN 1
PART CAN BE CADMIUM PLATED
110A 20-629 . . . PIN, ADJUSTER 1
115A 113-150-1 . . . GUIDE, SPRING 1
120A 54-492-1 . . . SLEEVE, GUIDE 1
125A 40-666 . . . SPRING 1
–130A N5000-150H . . . RING, RETAINING (V79136) 1
130B MS16625-4150 . . . RING, RETAINING 1
135A 50-598 . . . PLATE, INSTRUCTION 1
01
140A 45-231-1 . . . TUBE, ADJUSTER 1
145A 130-27 . . . BALL 1
150A FN12M02 . . . NUT, SELF-LOCKING (V56878) 1
PART CAN BE CADMIUM PLATED
155A 437-50 . . . INSULATOR ASSEMBLY 1
–160A 53-321 . . . RING, RETAINING 1
160B 53-411 . . . RING, RETAINING 1
POST SB 2-1577-32-9
163A 68-1359 . . . RING, BACK-UP 55A 2
(NP)
163B 549-70 . . . RING, BACK-UP 55A 2
POST SB 2-1577-32-11
165A MS20995C32 . . LOCKWIRE AR
165B 23320CA080 . . LOCKWIRE AR
170A 20-678 . . PIN, TORQUE 1
175A 25-147 . . COLLAR 1
PART CAN BE CADMIUM PLATED
180A NAS1149F0863P . . WASHER 1
PART CAN BE CADMIUM PLATED
185A 43-1395 . . BOLT 1
PART CAN BE CADMIUM PLATED
190A MS17826-8 . . NUT 1
PART CAN BE CADMIUM PLATED
195A MS24665-304 . . PIN, COTTER 1
200A 798A . . VALVE (VF0826) 2
–205A GA56999-1 . . . BODY ASSEMBLY 1
(NP)
–210A NAS1612-6 . . . PACKING, PREFORMED 1
210B NAS1611-015 . . . PACKING, PREFORMED 1
POST SL 2072
–210C NAS1611-015A . . . PACKING, PREFORMED 1
POST SL F6137-32-3344
215A 7612 . . . CAP, PROTECTIVE (VF0826) 1
220A MS20995C32 . . LOCKWIRE AR
220B 23320CA080 . . LOCKWIRE AR
225A NAS1612-6 . . PACKING, PREFORMED 2
225B NAS1612-6A . . PACKING, PREFORMED 2
POST SL F6137-32-3344
01
230A HTE711-218B . . FITTING ASSEMBLY, HYDRAULIC 2
(VK2523)
STORAGE PARTS
231A HTE717B . . CAP, PROTECTIVE (VK2523) 2
***
232A HTE760B3 . . . NIPPLE (VK2523) 1
(NP)
233A HTE7300E3-018 . . . PACKING, PREFORMED (VK2523) 1
(NP)
234A HTE1001B7 . . . SPRING (VK2523) 1
(NP)
235A HTE717B . . . DELETED
236A HTE761B8 . . . VALVE, NIPPLE (VK2523) 1
(NP)
237A HTE7300E3-014 . . . PACKING, PREFORMED (VK2523) 1
(NP)
238A HTE762-135B8 . . . NIPPLE, END (VK2523) 1
(NP)
240A MS20995C32 . . LOCKWIRE AR
240B 23320CA080 . . LOCKWIRE AR
245A 68-1363 . PACKING, PREFORMED 1
250A 466-8 . SENSOR ASSEMBLY, 1
TEMPERATURE
SEE 32-41-54 FOR DET
ATTACHING PARTS
255A NAS1149F0463P . WASHER 1
PART CAN BE CADMIUM PLATED
260A NAS1351C4H10 . SCREW 1
***
01
305A MS51844-61 . . SLEEVE, SWAGING WIRE 2
–310A 3201-04-03 . . PIN, DOUBLE DETENT (VF4492) 1
PART CAN BE CADMIUM PLATED
OPT TO 57539-1 (V84256)
OPT TO BLS4R03N (V84256)
310B 57539-1 . . PIN, DOUBLE DETENT (V84256) 1
PART CAN BE CADMIUM PLATED
(NP)
OPT TO BLS4R03N (V84256)
OPT TO 3201-04-03 (VF4492)
POST SB 2-1577-32-6
–310C BLS4R03N . . PIN, DOUBLE DETENT (V84256) 1
PART CAN BE CADMIUM PLATED
(NP)
OPT TO 3201-04-03 (VF4492)
OPT TO 57539-1 (V84256)
315A 548-1 . . COLLAR ASSEMBLY 1
320A NAS1149F0463P . WASHER 4
PART CAN BE CADMIUM PLATED
325A NAS1351C4H10 . SCREW 4
330A MS20995C32 . LOCKWIRE AR
330B 23320CA080 . LOCKWIRE AR
–335A 537-33-1 . SINK, HEAT 1ACEG 1
(NP)
–335B 537-33-2 . SINK, HEAT 1BDFG 1
(NP)
–335C 537-154-1 . SINK, HEAT 1HJKL 1
(NP)
POST SB 2-1577-32-10
–335D 537-154-2 . SINK, HEAT 1HJKL 1
(NP)
POST SB 2-1577-32-10
–335E 537-122-1 . SINK, HEAT 1P 1
(NP)
–335F 537-122-2 . SINK, HEAT 1P 1
(NP)
–335G 537-122-3 . SINK, HEAT 1MNP 1
POST SB 2-1577-32-14
–335H 537-122-4 . SINK, HEAT 1MNP 1
POST SB 2-1577-32-14
01
–340A 134-429-1 . . PLATE ASSEMBLY, PRESSURE 335A 1
(NP)
OPT TO 134-429-2 OVERHAULED
(VF6137)
–340B 134-429-2 . . PLATE ASSEMBLY, PRESSURE 335B 1
(NP)
–340C 134-806-1 . . PLATE ASSEMBLY, PRESSURE 335CDE 1
(NP) FGH
340D 134-806-2 . . PLATE ASSEMBLY, PRESSURE 335CDE 1
(NP) FGH
345A 133-1160-1 . . . DELETED
345B 133-1160-2 . . . DELETED
350A 170-255 . . . DELETED
355A 78-296 . . . DELETED
–360A 134-430-1 . . DISK ASSEMBLY, ROTOR 335A 5
(NP)
OPT TO 134-596-1 (VF6137)
–360B 134-430-2 . . DISK ASSEMBLY, ROTOR 335B 5
(NP)
OPT TO 134-430-1 OVERHAULED
(VF6137)
OPT TO 134-596-1 OVERHAULED
(VF6137)
OPT TO 134-596-2 (VF6137)
–360C 134-866-1 . . DISK ASSEMBLY, ROTOR 335CDE 5
(NP) FGH
OPT TO 134-790-1 (VF6137)
360D 134-866-2 . . DISK ASSEMBLY, ROTOR 335CDE 5
(NP) FGH
OPT TO 134-790-2 (VF6137)
365A 133-1159-1 . . . DELETED
365B 133-1159-2 . . . DELETED
370A 53-287 . . . DELETED
375A 56-923 . . . DELETED
380A 78-287 . . . DELETED
385A 133-1161-1 . . DISK, STATOR 335A 4
(NP)
OPT TO 133-1161-2 OVERHAULED
(VF6137)
385B 133-1161-2 . . DISK, STATOR 335B 4
(NP)
01
385C 133-1658-1 . . DISK, STATOR 335CD 4
(NP)
385D 133-1658-2 . . DISK, STATOR 335CD 4
(NP)
385E 133-1658-1 . . DISK, STATOR 335EF 1
(NP) GH
385F 133-1658-2 . . DISK, STATOR 335EF 1
(NP) GH
385G 134-768-1 . . DISK ASSEMBLY, STATOR 335EF 3
(NP) GH
385H 134-768-2 . . DISK ASSEMBLY, STATOR 335EF 3
(NP) GH
–390A 134-431-1 . . DISK ASSEMBLY, END PLATE 335A 1
(NP)
OPT TO 134-431-2 OVERHAULED
(VF6137)
OPT TO 134-597-1 (VF6137)
OPT TO 134-597-2 OVERHAULED
(VF6137)
–390B 134-431-2 . . DISK ASSEMBLY, END PLATE 335B 1
(NP)
OPT TO 134-597-2 (VF6137)
–390C 134-867-1 . . DISK ASSEMBLY, END PLATE 335CDE 1
(NP) FGH
OPT TO 134-791-1 (VF6137)
390D 134-867-2 . . DISK ASSEMBLY, END PLATE 335CDE 1
(NP) FGH
OPT TO 134-791-2 (VF6137)
–395A 78-291 . . . RIVET 12
(NP)
–400A 322-124 . . . BUTTON, TORQUE 390AB 12
(NP)
–400B 322-124-1 . . . BUTTON, TORQUE 390CD 12
(NP)
405A 133-1162-1 . . . DELETED
405B 133-1162-2 . . . DELETED
410A 53-345 . CLIP 4
415A 378-48-1 . SHIELD ASSEMBLY, HEAT 1
–420A 4-357 . PLATE ASSEMBLY, TORQUE 1
01
–425A 184-895-1 . . PLATE, TORQUE (V97153) 1
(NP)
OPT TO 184-895-2 (VF6137)
425B 184-895-2 . . PLATE, TORQUE 1
(NP)
OPT TO 184-895-1 (V97153)
–428A 538-5 . . BUSHING ASSEMBLY 1
430A 26-391 . . . BUSHING 1
(NP)
435A 26-392 . . . BUSHING 1
(NP)
440A VS675S02 . . RING, RETAINING (V51814) 1
445A 378-47-3 . . SHIELD ASSEMBLY, HEAT 1
450A MS21206C3 . . WASHER 3
PART CAN BE CADMIUM PLATED
455A AN3C5A . . BOLT 3
PART CAN BE CADMIUM PLATED
–460A NM10-2525TL . . RIVET (V70127) 3
PART CAN BE CADMIUM PLATED
461A MS21042-3 . . NUT AR
PART CAN BE CADMIUM PLATED
REPAIR ONLY
OPT TO NM10-2525TL (VF8266)
462A NAS1149C0363B . . WASHER AR
FIO: USED ONLY WITH P/N
MS21042-3
REPAIR ONLY
465A 43-1396 . BOLT 14
470A MS20002C10 . WASHER 14
PART CAN BE CADMIUM PLATED
475A MS20995C32 . LOCKWIRE AR
475B 23320CA080 . LOCKWIRE AR
480A 50-639 . PLATE, IDENTIFICATION 1
485A 50-640 . PLATE, INSTRUCTION 1