Documente Academic
Documente Profesional
Documente Cultură
horizontal. The required capacity is 50 tonnes per hour, length of convcymp is 25 m, bulk density of sand
1.60 tunne/cubic m and is abrasive in nature, loading cfficienc~r is 0.125, sere",' pitch == .OD, where D is
nominal diameter of screw, r.p.m. of the screw IS 60, inclination factor is 0.65, mass flow rate IS
60 tcnnes / hr, progress resistances coefficient is 4. Find out total power required for the screw in kW
B) Rated capacity of the FLT is 2000 kg and load centre is 5.':;{Jrrun. l)istancc bctv,'cen front \vbeels to
heel of the fork is 450 rnrn
ii] If a lead is to be carried v.'hose CG IS at a distance of 650 mm from the heel of the forks ( distance
Weight
C) Calculate the motor power output required in kW in belt conveyor if required peripheral force =
2444.07 N, belt speed 2.65 m/sec, wrap resistance at driving pulley' = 230 N, drive pulley bearing
resistance = 44 N and final transnlission efficiency is 0.80o/r).
D) A bat tcrv-oporated FLT weighs 4000 lbs includingbattery {y, oper-ator. It is carrying a weight of 2000
lbs The truck lifts the load to 2 ft &, carries the load 10 a distance of 20U [1 of which 170 It is along !cvt'l
road (y, balance 30 ft on and upgrade of 6'/{,. Aftcr discharging the load, it returns by the
same route. Calculate total watt-hr of energy spent by the truck. Select suitable battery if the truck
has to make 200 such trips daily. ( Assume 2 tilts with load I tilt without load in each trip). 8
E) 4. (a) The power required at the driving pulley just for driving thebelt is 120kW. The tension in the
slack side is 50N and MEW= 0.4, u= 150 degrees. Calculate the belt speed in mm/sec.
(b) Calculate the conveying capacity of a troughed belt conveyor if B = belt width = 500mm, V =
1200mm/sec, y = bulk density
is 2000 tonnes/m ', PHAI = static angle of repose is 45 degrees,
LAMDA.~ 60 degrees.
F) A battery operated FLT weighs 4000 pounds including weight 6 of battery and operator. It is carrying a
weight of 2000 pounds.The truck lifts the load to 2 ft and carries the load to a distance of 200 ft of which
170 is along level road and balance 30 ft on an upgrade of 6%. After discharging the load it returns over
same route. Calculate total watt-hours of energy spent by the
G) Calculate the motor power output required kW in belt conveyor if required peripheral force =
2444.07N, belt speed =2.65 mtr/sec, wrap resistance at driving pulley = 230N, drive
pulley hearing resistance = 44N and final transmission efficiency is 0.80%.
H) The power required at driving pulley just for the driving the belt is 120 kW. The tension at slack
side is 50 N and Meu(~l)is 0.4 and Alpha ((.()is 150 degrees. Calculate the belt speed in mrn.' sec.
b) Calculate the conveying capacity of troughed belt conveyor if B ~ belt width ~ 500 m,
v~1200 mmy sec, y ~ bulk density is 2 tonnes /m 3.o static angle of repose IS 45 degrees.
lamda ~ 60 degrees
J) Calculate the conveyor capacity of a troughed belt conveyor if belt width is 500 mm, velocity is 1200
mmZsec, bulk density of carrying material is 2000 tonnes /m 3 , static angle of repose is 45° and
troughing angle is 60°.
b) In an E.O.T. crane, number of falls of the rope is 8. The pay load is 80 tons. Weight of the bottom
block is 3% of the pay load. Friction loss per fall is 2.5%. Taking a factor of safety of 6, calculate the
design load per fall of rope.