Documente Academic
Documente Profesional
Documente Cultură
UNIVERSIDAD DE CARTAGENA
FACULTAD DE INGENIERÍA
LABORATORIO DE FÍSICA II
RESUMEN
Este presente informe fue elaborado con base a los procedimientos y los cálculos
desarrollados en el laboratorio, el cual tenía como objetivo principal calcular la
resistencia de varios resistores en diferentes montajes en individuales, en serie y
en paralelo. Para realizar dichos procedimientos, se necesitó de instrumentos
como el multímetro, protoboard, resistores y entre otros. Se implementaron dos
métodos para calcular la resistencia inicial de cada resistor, el método teórico
(suma de colores del resistor) y el método experimental (mediante el multímetro), y
con base a esto se procedió a montar los resistores en el protoboard, donde
mediante el multímetro y la ayuda de cables caimán se iba calculando la
resistencia en cada montaje que se tenía al unir varios resistores ya sea en serie o
en paralelo. Al terminar todas las mediciones de resistencias obtenidas en lo
montajes mediante el multímetro, se compararon estos valores (experimentales)
con los valores obtenidos al realizar las sumas de los resistores mediante los
valores establecidos por la tabla del código de colores (teórico). Una vez
comparados los valores, al ver que el porcentaje de error era muy mínimo, se
pudo determinar que los procesos realizados en los montajes y en las sumas, fue
correcto.
ABSTRACT
This report was prepared based on the procedures and calculations developed in
the laboratory, whose main objective was to calculate the resistance of several
resistors in different assemblies in individual, series and parallel. To perform these
procedures, instruments such as the multimeter, protoboard, resistors and others
were needed. Two methods were implemented to calculate the initial resistance of
each resistor, the theoretical method (sum of colors of the resistor) and the
experimental method (using the multimeter), and based on this, the resistors were
mounted on the breadboard, where the multimeter and the help of caiman cables
was calculating the resistance in each assembly that was had when joining several
resistors either in series or in parallel. When finishing all the measurements of
resistances obtained in the assemblies by means of the multimeter, these
(experimental) values were compared with the values obtained when making the
sums of the resistors by means of the values established by the table of the color
code (theoretical). Once the values were compared, seeing that the percentage of
error was very minimal, it was possible to determine that the processes performed
in the assemblies and in the sums, was correct.
Fuente:
https://www.fisicalab.com/apartado/as
ociacion-de-resistencias#contenidos
Fuente: 1 𝑅1 + 𝑅2 + ⋯ + 𝑅𝑛
=
https://www.fisicalab.com/apartado/as 𝑅 𝑅1 ∗ 𝑅2 ∗ … ∗ 𝑅𝑛
ociacion-de-resistencias#contenidos
3. METODOLOGIA 4. RESULTADOS Y DISCUSIÓN
% 𝑒𝑟𝑟𝑜𝑟 = 0,115%
5. CONCLUSION
REFERENCIAS BIBLIOGRÁFICAS
𝑅 = 1017,7Ω
1. Garcia, J. (s.f.). Qué es la
𝑅′ = 1019Ω resistencia eléctrica.
% 𝑒𝑟𝑟𝑜𝑟 = 0,128% Recuperado 21 mayo, 2019,
de
Circuito 5: http://www.asifunciona.com/ele
ctrotecnia/ke_resistencia/ke_re
sistencia_1.htm
2. Fernandez, J., & Coronado, G.
(s.f.). Asociación de
resistencias. Recuperado 21
mayo, 2019, de
https://www.fisicalab.com/apart
𝑅 = 8670Ω ado/asociacion-de-
resistencias#contenidos