Documente Academic
Documente Profesional
Documente Cultură
200
PC200-8M0 HORSEPOWER
Gross: 110 kW 147 HP @2000 rpm
Net: 103 kW 138 HP @ 2000 rpm
OPERATING WEIGHT
20500-22010 kg
45,195-48,525 lb
BUCKET CAPACITY
Me 1.0 m3 1.24 yd3
2
HYDRAULIC EXCAVATOR PC200-8M0
PC200-8M0
HORSEPOWER GROSS : 110 kW 147 HP / 2000 rpm
NET : 103 kW 138 HP / 2000 rpm
OPERATING WEIGHT 20500-22010 kg
BUCKET CAPACITY 1.0 m3 Me
3
ECOLOGI & ECONOMY
EKOLOGI & EKONOMI
Low Fuel Consumption
Komatsu Technology
Tehnologi Komatsu
4
HYDRAULIC EXCAVATOR PC200-8M0
Low Emission Engine Working Modes Selectable
Komatsu SAA6D107E-1 reduced NOx emission by 29% compared The PC200-8M0 excavator is equipped with six working modes (P, E, L,
with the PC200-7. This engine is U.S. EPA Tier 3 and EU Stage 3A B, ATT/P and ATT/E mode). Each mode is designed to match engine speed
emissions equivalent. and pump output to the application. This provides the flexibility to match
equipment performance to the job at hand.
Enjin Rendah Emisi
Enjin SAA6D107E-1 Komatsu mampu Mode Kerja Yang Bisa Dipilih
mengurangi emisi NOx sebesar 29% Hidrolik excavator PC200-8M0 dilengkapi dengan enam (6) mode kerja
dibandingkan dengan PC200-7. Enjin (mode P, E, L, B, ATT / P dan ATT / E). Setiap mode dirancang untuk
ini sama dengan emisi EPA Tier 3 dan menyesuaikan kecepatan enjin dan aplikasi output pompa. Hal ini
EU Stage 3A. memberikan fleksibilitas untuk menyesuaikan kinerja peralatan untuk
pekerjaan tangan.
Low Operation Noise Working Mode Application Advantage
Enables a low noise operation using the low-noise engine and methods P Power mode
• Maximum production/power
to cut noise at source. • Fast cycle times
• Good cycle times
E Economy mode
• Better fuel economy
Kebiisingan Rendah Selama Beroperasi
• Suitable attachment speed
Bekerja dengan kebisingan rendah dimungkinkan oleh penggunaan L Lifting mode • Lifting capacity is increased 7% by raising
enjin dengan kebisingan rendah dan metode untuk mengurangi hydraulic pressure.
kebisingan pada sumbernya. B Breaker mode • Optimum engine rpm, hydraulic flow
Attachment • Optimum engine rpm, hydraulic flow 2way
ATT/P
Power mode • Power mode
Attachment • Optimum engine rpm, hydraulic flow, 2way
ATT/E
Power mode • Economy mode
Idling Caution
To prevent unnecessary fuel
consumption, an idling caution is Large Digging Force
displayed on the monitor, if the engine When press the left knob switch which is called the one-touch power max.
idles for 5 minutes or more. Switch and when it is kept pressed, this function temporarily increases
digging force for 8.5 seconds of operation.
Peringatan Idling
Untuk mencegah konsumsi bahan Kekuatan Menggali Kuat
bakar yang sia-sia peringatan idling Ketika menekan saklar tombol kiri yang disebut satu-sentuhan daya max.
ditampilkan pada monitor, jika enjin hidup pada keadaan idle selama 5 Beralih dan ketika itu tetap ditekan, fungsi ini sementara meningkatkan
menit atau lebih. menggali kekuatan untuk 8,5 detik operasi.
ECO-gauge that Assists Energy-saving Operations Maximum arm crowd force (ISO 6015):
Equipped with the ECO-gauge that can be recognized at a glance on the
101 kN (10.3 t) 108 kN (11.0 t) 7 % UP
right of the multi-function color monitor for environment-friendly energy- (with Power Max.)
saving operations. Allows focus on
operation in the green range with Maximum bucket digging force (ISO 6015):
reduced CO2 emissions and efficient 138 kN (14.1 t) 149 kN (15.2 t) 8 % UP
(with Power Max.)
fuel consumption.
Measured with Power max. fuction , 2925 mm arm
and ISO 6015 rating.
ECO-gauge yang membantu
Pengoperasian Hemat Energi
Dilengkapi dengan Eco-gauge yang
dapat dilihat selintas disebelah
ECO gauge
kanan monitor berwarna multi-fungsi
untuk pekerjaan yang menghemat
energi dan ramah lingkungan. Memungkinkan pemusatan perhatian One-touch
power max. switch
pada pekerjaan di kisaran hijau dengan emisi CO2 yang berkurang dan
konsumsi bahan bakar yang efisien.
5
COMFORT
KENYAMANAN
Kabin Bertekanan
Pendingin udara, filter udara dan tekanan di dalam
kabin yang lebih tinggi mencegah debu dari luar
masuk ke dalam kabin.
6
HYDRAULIC EXCAVATOR PC200-8M0
SAFETY
KESELAMATAN
ROPS Cab Pump/Engine Room Partition
The machine is equipped with a ROPS cab that conforms to ISO 12117-2 for Pump/engine room partition prevents oil from sprayin onto the en ine if a
excavators as standard equipment. The ROPS cab has high shock-absorption hydraulic hose should fail.
performance, featuring excellent durability and impact strength. It also satisfies
the requirements of ISO OPG top guard level 1 for falling objects. Combined with Partisi Ruang Pompa/Enjin
the retractable seat belt, The ROPS cab protects the operator in case of tipping Partisi ruang pompa enjin mencegah oli menyembur ke atas enjin jika
over and against falling objects. seandainya ada selang hidrolik pecah.
Cab ROPS
Lock Lever
Mesin ini dilengkapi dengan kabin ROPS yang sesuai dengan ISO 12117-2
Locks the hydraulic pressure to prevent
untuk excavator sebagai perlengkapan standar. Kabin ROPS memiliki performa
unintentional movement. Neutral start
peredam kejut yang tinggi, menampilkan daya tahan dan kekuatan impak yang
function allows machine to be started
sangat baik. Hal ini juga memenuhi persyaratan ISO OPG top guard level 1 untuk
only in lock position.
benda yang jatuh. Dikombinasi dengan sabuk pengaman yang ditarik. Kabin
ROPS melindungi operator dalam kasus mesin terbalik dan terhadap benda yang Lock Lever
jatuh. Mengunci tekanan hidrolik untuk
ROPS CAB STRUCTURE
mencegah gerakan yang tidak
disengaja. Fungsi start netral hanya
memungkinkan mesin distart dalam
posisi terkunci.
7
ICT & KOMTRAX
ICT & KOMTRAX
Large Multi-lingual High Resolution LCD Monitor
A large user-friendly high resolution LCD color monitor enables safe,
1 2 3 accurate and smooth work. Visibility and resolution are further improved
compared with current 7-inch large TFT LCD.Simple and easy to operate
switches. Function keys facilitate multi-function operation. Display data
7 in 13 languages to globally support operators around the world includ
bahasa.
TFT : Thin Film Transistor
LCD : Liquid Crystal Display
Fungsi Monitor
Controller memantau level oli enjin,
suhu cairan pendingin, daya baterai, penyumbatan filter udara, dll. Jika
controller menemukan kondisi abnormal, hal itu akan ditampilkan pada
LCD.
Maintenance Function
ECO guidance ECO guidance menu Monitor informs replacement time
of oil and filters on LCD when the
replacement interval is reached.
Fungsi Pemeliharaan
Monitor akan memberitahu waktu
penggantian oli dan filter-filter
pada tampilan LCD bila waktu
penggantian itu telah tiba.
ECO guidance records
Trouble Data Memory Function
Monitor stores abnormalities for effective troubleshooting.
Operation records
Fungsi Memori Data Masalah
Monitor menyimpan kejadian abnormal agar troubleshooting menjadi
Avarage fuel consumption logs
lebih efektif.
8
HYDRAULIC EXCAVATOR PC200-8M0
9
MAINTENANCE
PERAWATAN
Side-by-side cooling Easy Access to Engine Oil Filter and Fuel Drain Tangki Bahan Bakar Berkapasitas Besar dan
Since radiator, aftercooler and oil cooler are arranged Valve Diproses Secara Rustproof
in parallel, it is easy to clean, remove and install them. Engine oil filter and fuel drain valve are remote Tangki bahan bakar dengan kapasitas besar. Efektif
Radiator, aftercooler, and oil cooler made of aluminium mounted to improve accessibility. tahan terhadap korosi menggunakan proses rustproof
have high cooling efficiency and are easily recycled
Akses yang Mudah ke Filter Oli Mesin dan Katup
Sloping Track Frame
Pendinginan yang Berdampingan Pembuang Bahan Bakar
Prevents dirt and sand from accumulating and allows
Radiator, aftercooler dan pendingin oli disusun parallel, Pengukur permukaan oli mesin dan filter bahan bakar
easy mud removal.
mudah untuk dibersihkan, dilepaskan dan dipasang dipasang disisi mesin yang sama agar mudah diakses.
kembali. Radiator, aftercooler dan pendingin oli terbuat Track Frame dengan Bentuk yang Miring
dari aluminium yang memiliki efisiensi pendinginan Mencegah lumpur dan tanah terkumpul dan
yang tinggi dan mudah didaur ulang. memudahkan perbersihan kotoran.
10
HYDRAULIC EXCAVATOR PC200-8M0
SAFETY
KESELAMATAN
High Rigidity Work Equipment
Boom and arms are constructed of thick plates of high tensile strength steel. In addition, these structures are designed with large cross sectional areas and generous
use of castings. The result is working attachments that exhibit long term durability and high resistance to bending and torsional stress.
Alat Kerja Kekakuan Tinggi
Boom dan arm terbuat dari pelat baja yang tebal dengan kekuatan gaya tarik tinggi. Selain daripada itu, struktur ini dirancang dengan penampang yang luas, besar
dan murah dengan penggunaan coran. Hasilnya adalah attachment yang menunjukkan daya tahan jangka panjang dan resistensi yang tinggi terhadap kelenturan dan
stres torsi kerja.
11
KOMATSU BRAND BUCKET
BUCKET MEREK KOMATSU
KOMATSU Brand Bucket General Purpose with Me Bucket
Bucket Merek Komatsu Me Bucket dengan General Purpose
greatly increased.
Tinggi Produktivitas dengan Hambatan
Penggalian Rendah
Profil bucket baru yang ideal menghasilkan hambatan
yang lebih rendah di dalam & luar bucket sehingga
produksi akan meningkat.
Kondisi bawah
Garis Tooth
Bucket Konvensional
Kondisi bawah
Garis Tooth
Load
Machine power is mostly medium, but occasionally high.
Bucket movements are smooth with minor shock load.
General Purpose Bucket penetrates easily.
(GP) Wear
Material is lightly abrasive. Some sand may be medium abrasive.
Soil
Mostly loose sand, gravel and finely broken materials.
12
HYDRAULIC EXCAVATOR PC200-8M0
SPECIAL ATTACHMENT
SPESIFIKASI KHUSUS
Breaker
Equipped With Piping for Breaker Installation
Equips PC200-8M0 for breaker and crusher installation. Hydraulic flow rate can be regulated by setting Breaker Mode on monitor panel during breaker operation.
Hydraulic breaker
The hydraulic breaker is an attachment tool used for crushing rock beds and paved surfaces,
demolishing concrete structures, etc. The large gas chamber, ideal gas pressure ratio, and long-
stroke piston deliver a powerful impact force. Since the breaker unit does not require an accumulator,
the number of parts has been reduced, resulting in lower maintenance costs.
Hidrolik Breaker
Hidrolik Breaker adalah alat attachment digunakan untuk menghancurkan batuan dan permukaan
beraspal, menghancurkan struktur beton, dll. Kapasitas gas banyak, rasio tekanan gas ideal, dan panjang-stroke piston memberikan dampak kekuatan yang besar.
Karena unit breaker tidak memerlukan akumulator, jumlah komponen telah berkurang, sehingga biaya perawatan yang lebih rendah.
13
DIMENSIONS
PC200-8M0
D Overall width** 3000 mm
E Overall height (to top of cab)* 3040 mm
F Ground clearance, counterweight 1085 mm
G Ground clearance (minimum) 440 mm
H Tail swing radius 2750 mm
I Track length on ground 3275 mm
J Track length 4070 mm
K Track gauge 2200 mm
L Width of crawler 3000 mm
M Shoe width 800 mm
N Grouser height 26 mm
O Machine cab height 2095 mm
P Machine cab width 2710 mm
Q Distance, swing center to rear end 2710 mm
WORKING RANGE
Arm 2925 mm
A Max. digging height 10000 mm
B Max. dumping height 7110 mm
C Max. digging depth 6620 mm
Max. vertical wall
D 5980 mm
digging depth
Max. digging depth of cut
E 6370 mm
for 2440 mm level
F Max. digging reach 9875 mm
G Max. digging reach at ground level 9700 mm
H Min. swing radius 3040 mm
SAE 1179 Rating
max. 15200 kg
14
HYDRAULIC EXCAVATOR PC200-8M0
SPECIFICATION
SPESIFIKASI
ENGINE DRIVES AND BRAKES
Steering control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Two levers with pedals
Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Komatsu SAA6D107E-1 Drive method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydrostatic
Type . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Water-cooled, 4-cycle, direct injection Maximum drawbar pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 kN 18200 kgf
Aspiration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Turbocharged, aftercooled Gradeability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70%, 35°
Number of cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Maximum travel speed: High . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 km/h
Bore. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 mm 4.21” (Auto-Shift) Mid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.1 km/h
Stroke. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 mm 4.88” (Auto-Shift) Low. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 km/h
Piston displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.69 ltr 408 in3 Service brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic lock
Horsepower: Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mechanical disc brake
SAE J1995 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Gross 110 kW 147 HP
ISO 9249 / SAE J1349 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Net 103 kW 138 HP
Rated rpm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 rpm
Fan drive type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Mechanical UNDER CARRIAGE
Governor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All-speed control, electronic
EPA Tier 3 and EU Stage 3A emissions equivalent Center frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X-frame
Track frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Box-section
Seal of track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sealed track
HYDRAULICS
Track adjuster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic
Type . . . . . . . . . . . . . . . . . . . . . . HydrauMind (Hydraulic Mechanical Intelligence New Design) Number of shoes (each side) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
system, closed-center system with load sensing valves and Number of carrier rollers (each side) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
pressure compensated valves Number of track rollers (each side) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Number of selectable working modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Main pump:
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Variable displacement piston type COOLANT AND LUBRICANT
Pumps for . . . . . . . . . . . . . . . . . . . . . . . . . . . Boom, arm, bucket, swing, and travel circuits CAPACITY (REFILLING)
Maximum flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439 ltr/min 116 U.S. gal/min
Supply for control circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Self-reducing valve Fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 ltr
Hydraulic motors: Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20.4 ltr
Travel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 x axial piston motors with parking brake Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.1 ltr
Swing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 x axial piston motor with swing holding brake Final drive, each side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.6 ltr
Relief valve setting: Swing drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.5 ltr
Implement circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . 37.3 MPa 380 kgf/cm2 5,400 psi Hydraulic tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135 ltr
Travel circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37.3 MPa 380 kgf/cm2 5,400 psi
Swing circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28.9 MPa 295 kgf/cm2 4,195 psi
Pilot circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 MPa 33 kgf/cm2 470 psi
Hydraulic cylinders:
OPERATING WEIGHT (APPROXIMATE)
(Number of cylinders - bore x stroke x rod diameter)
Boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 120 mm x 1334 mm x 85 mm
Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 135 mm x 1490 mm x 95 mm Operating weight including 5700 mm one-piece boom, 2925 mm arm, SAE heaped
Bucket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 115 mm x 1120 mm x 80 mm 1.0 m3 Me bucket, rated capacity of lubricants, coolant, full fuel tank, operator, and
standard equipment.
PC200-8M0
SWING SYSTEM Shoes
Operating Weight Ground Pressure
Drive method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydrostatic
0.36 kgf/cm2
Swing reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Planetary gear 800 mm 20500 kg
35.3 kPa
Swing circle lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Grease-bathed
Service brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic lock
Holding brake/Swing lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mechanical disc brake
Swing speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.4 rpm
15
PC195LC-8
STANDARD EQUIPMENT
• Additional filter system for poor-quality fuel • Multi-function color monitor • Starting motor, 4.5 kW/24 V
• Air conditioner • Power maximizing system • Track guiding guard, center section
• Alternator, 35 A, 24 V • PPC hydraulic control system • Track roller, 7 each side
• Arm, 2925 mm arm assembly • Radiator and oil cooler dust proof net • Track shoe, 800 mm triple grouser
• Auto-decel • Rear reflector • Travel alarm
• Automatic engine warm-up system • Rearview mirrors (R.H, L.H, rear, sidewise) • Working light, 5 (boom, boom cylinder,
• Batteries, 110Ah / 12 V x 2 • Refill pump R.H and 2 on cab)
• Bucket 1.0 m3 Me • ROPS cab (ISO 12117-2) • Working mode selection system
• Boom, 5700 mm • Slip-resistant plates
• Boom holding valve • Seat belt, retractable
• Counterweight • Service valve (1 additional port)
• Dry type air cleaner, double element
• Electric horn
• EMMS monitoring system
• Engine, Komatsu SAA6D107E-1
• Engine overheat prevention system
• Hydraulic track adjusters (each side)
• Komtrax
• Fan guard structure • Suction fan
OPTIONAL EQUIPMENT
• Alternator, 60 Ampere, 24 V • Cab front guard • Track roller guards (full length)
• Bolt-on top guard, [Operator Protective - Full height guard • Working light, 1 (counterweight)e
Guards level 2] - Half height guard
• Seat, suspension
16
HYDRAULIC EXCAVATOR PC200-8M0
SPECIAL SPECIFICATION
SPESIFIKASI KHUSUS
PC200-8M0
Logging
OPERATING WEIGHT (APPROXIMATE)
SPECIAL FEATURE
Safety guard : Cabin guard (with emergency Strong upper roller Track frame with strong undercover
exit), side door guards (L.H, R.H), Deck guard
DIMENSIONS
17
WORKING RANGE
STANDARD EQUIPMENT
OPTIONAL EQUIPMENT
18
HYDRAULIC EXCAVATOR PC200-8M0
SPECIAL SPECIFICATION
SPESIFIKASI KHUSUS
PC200-8M0 Super long front attachment boasts a huge digging reach. An excavator with this
attachment highly improves working efficiency in various works such as river
conservation, lake dredging, slope finishing and materials carrying where an
WORKING RANGE
MODEL
PC200-8MO SLF
ITEM
Operating weight 21080 kg
Bucket capacity 0.45 m3
A Maximum digging height 13500 mm
B Maximum dumping height 1295 mm
C Maximum digging depth 11390 mm
D Maximum digging reach 15000 mm / 50 ft
E Tail swing radius 4235 mm
o
F Maximum digging depth on 35 slope 6925 mm
o
G Maximum digging reach on 35 slope 12105 mm
Specific gravity 1.1 ton/m3
19
DIMENSIONS
A Distance, swing center to front end 9000 mm H Overall height (to top of cab) 3040 mm
B Distance, swing center to rear end 2710 mm I Machine cab width 2710 mm
C Overall height 3310 mm J Ground clearance, counterweight 1085 mm
D Overall width 3000 mm K Machine cab height 2095 mm
E Shoe width 800 mm L Track length on ground 3275 mm
F Ground clearance (minimum) 440 mm M Track length 4070 mm
G Track gauge 2200 mm
STANDARD EQUIPMENT
OPTIONAL EQUIPMENT
20
HYDRAULIC EXCAVATOR PC200-8M0
SPECIAL SPECIFICATION
SPESIFIKASI KHUSUS
PC200-8M0
Breaker
Equipped With Piping for Breaker Installation
Equips PC200-8M0 for breaker and crusher installation. Hydraulic flow rate can be regulated by setting Breaker Mode on monitor panel during breaker operation.
Hydraulic breaker
The hydraulic breaker is an attachment tool used for crushing rock beds and paved surfaces,
demolishing concrete structures, etc. The large gas chamber, ideal gas pressure ratio, and
long-stroke piston deliver a powerful impact force. Since the breaker unit does not require an
accumulator, the number of parts has been reduced, resulting in lower maintenance costs.
Hidrolik Breaker
Hidrolik Breaker adalah alat attachment digunakan untuk menghancurkan batuan dan permukaan
beraspal, menghancurkan struktur beton, dll. Kapasitas gas banyak, rasio tekanan gas ideal, dan panjang-stroke piston memberikan dampak kekuatan yang besar.
Karena unit breaker tidak memerlukan akumulator, jumlah komponen telah berkurang, sehingga biaya perawatan yang lebih rendah.
21
www.Komatsu.com Printed in Indonesia 12-2018