Documente Academic
Documente Profesional
Documente Cultură
2. A certain manufacturing plant utilizes plenty of air in its operation. Ambient air passes through
an adiabatic humidifier before being charge to the plant. The operation of an adiabatic
humidifier is similar to
a. cooling tower
b. spray chamber
c. coke packed dehumidifier
d. gas absorber
3. In a PFFP the rate of washing is equal to ________ of the final filtration rate.
a. 1/2
b. 1/4
c. 1
d. 2
4. In filtration operation involving incompressible cakes, the flow rate is directly proportional to
a. viscosity of the filtrate
b. thickness of the filter cake
c. the pressure applied
d. the size of the cake particles
7. The latent heat evolved when solid forms from solution and varies with both temperature and
concentration is called
a. heat of dilution
b. heat of vaporization
c. heat of crystallization
d. heat of fusion
10. The portion of water in the wet solid that cannot be removed by the air in its contact is
called
a. free moisture
b. final moisture
c. equilibrium moisture content
d. critical free moisture
11. This type of drier is used for drying pasty materials such as wet filter cakes and lumpy solids.
a. rotary drier
b. flash drier
c. tray drier
d. continuos drier
12. At the falling rate drying the rate at which moisture is removed from the solid material
a. increase with time
b. decrease with time
c. remains constant
d. no more drying takes place
13. A SWC is to be used to produce 1 ton/ h of copperas crystals by cooling of a sat’d solution
which enters the crystallize at 120ºF. the slurry leaving the crystallize will be at 80ºF. cooling
water enters the crystallize jacket at 60ºF and leaves at 70ºF. it may be assumed that U for
the crystallization is 35. There are 3.5 ft2 of cooling surface per foot of crystallize length.
DATA:
Heat of solution = 4400 cal/ gmole
Cp copperas = 0.7 BTU/ lb-ºF
Solubility:
@ 120ºF = 140 parts copperas / 100 parts water
80ºF = 74 parts copperas / 100 parts water
14. A batch of 1000 kg of KCl is dissolved in sufficient water to make a sat’d solution @ 363 ºK,
where the solubility is 35 w % KCl in water.the solution is cooled to 293 K which temp. The
solubility is 25.4 w %. The weight of the crystal obtained if 5% of the original water
evaporates on cooling is
a. 400 kg
b. 238 kg
c. 200 kg
d. 480 kg
15. A plate and frame filter press is used to filter certain sludge for 2 h at constant pressure.
Washing is done by using 10% of the filtrate collected. The time of washing is
a. 100 min
b. 96 min
c. 16 min
d. 100 h
If only ½ of the original filtrate volume were collected with the area remaining the same, the
filtration time is
a. 20.5 min c. 48.6 min
b. 24.4 min d. 38.3 min
18. If the rate of reaction is independent of the concentration of the reactants, the reaction is said
to be :
a. second order c. first order
b. zero order d. third order
23. A reaction is known to be first order in A. A straight line will be obtained by plotting
a. 1 / CA versus time c. log CA versus reciprocal time
b. CA versus time d. log CA versus time
24. The activation energy of a reaction can be obtained from the slope of a plot of
a. k vs. log 1/T c. log k vs. 1/T
b. log k vs. T d. k vs. log T
28. A certain reaction has a special rate constant of 4.27 x 10-3 / S at 250C and 7.35 x 10-2 / S at
800C. The energy of activation is kJ per mole is
a. 45.2 c. 104
b. 5.44 d. 860
29. The isothermal irreversible aqueous phase reaction A + B E at 100 0F obeys dCE / dt =
rE = kCACB ; k = 15 ft3 / 1 lbmole-h. Using a 1000 ft3 stirred tank reactor with an aqueous feed
of 2000 ft3 / / h1 the outlet concentrate of E if the inlet concentrate of A + B are both 0.25
lbmole / ft3 is
a. 0.4233 lbmole / ft3 c. 0.1332 lbmole / ft3
3
b. 0.1223 lbmole / ft d. 0.3122 lbmole / ft3
30. The composition of the reaction component vary from position to position along the path of a /
an
a. CFSTR c. batch reactor
b. adiabatic reactor d. plug flow reactor
31. The reacting substance follow one or more path to give different products
a. consecutive reaction c. parallel reaction
b. reversible reaction d. back mix reaction
32. The reactants are charged at the same time and concentration of solution varies with time
a. CFSTR c. batch reactor
b. plug flow reaction d. flow reactor
33. For saturated steam at 1 atm. condensing outside tube at 60 C, surface temperature I in
degree Celcius is
a. 60
b. 70
c. 80
d. 90
34. A property of solid which is indicated by the conventional scratch criteria and can be
measured by indention
a. friability
b. toughness
c. hardness
d. brittleness
35. It is the fraction of the radiation leaving from a surface that strikes to the other surface directly
a. reflectivity
b. transmissivity
c. absorptivity
d. view factor
36. At 100 C the gaseous reaction A B + C is observed to be first order. On starting with pure
A, it is found that at the end of 10 minutes, the total pressure of the system is 176 mmHg and
after a long time, the total pressure of the system is 270 mmHg. The half life of the reaction
is
a. 10.65 min
b. 0.65 min
c. 11 min
d. 10 min
e. 10.5 min
38. Given a single horizontal oxidized steel pipe with an outer diameter of 1 in. and surface
temperature of 180F. Determine the combined convective and
And radiation film coefficient ( BTU/h-ft-F) if the enclosed ambient temperature is 80 F
a. 2.5
b. 2.25
c. 2.15
d. 2.07
A single effect evaporator is operating under the following conditions:
Feed----------------------- 40,000 lb/hr
Xf--------------------------- 5% solid
Tf--------------------------- 200F
Xp-------------------------- 45% solid
Separation temperature of the vapor going into condenser is 125 F. Specific
heat of all solutions is 1 cal/gC. Overall heat transfer coefficient is
500 BTU/hr-ft.ft F. Assume no boiling point rise.
45. A separation process wherein a liquid solvent is used to dissolve a soluble solid from an
insoluble solid
a. solvent extraction
b. absorption
c. leaching
d. adsorption
46. A distilling column is composed of 7 theoretical plates in the enriching section and 8
theoretical plates in the stripping section. The overall plate efficiency is 50%, then the actual
number of plates is
a. 15
b. 30
c. 16
d. 32
52. It is the grant issued by the Philippine Government giving an inventor, maker or designer the
right to exclude others from making, using or selling his invention, utility or design.
a. trademark c. patent
b. copyright d. trade names
56. It is a type of physical operation by which a desired step in an industrial process is controlled
or conducted.
a. unit process c. chemical process
b. unit operation d. heating
59. The chemical engineer shall uphold at all times the _________ of the chemical engineering
profession and shall protect it from misinterpretation.
a. standards c. impartiality
b. integrity d. best
60. A set of using, selling and making of the invention without the consent of the inventor.
a. infringement c. illegal use
b. pirating d. licensing
70. It includes word, name, symbol, sign or device or any combination thereof.
a. service mark c. goods
b. trademark d. IPO mark
73. The chemical engineer shall ______________ to give credit to those to whom credit is
properly due.
a. see to it c. endeavor at all times
b. make sure d. act accordingly