Documente Academic
Documente Profesional
Documente Cultură
2
English (GB) Installation and operating instructions
English (GB)
Original installation and operating instructions. 1. Symbols used in this document
CONTENTS Warning
Page If these safety instructions are not observed, it
1. Symbols used in this document 3 may result in personal injury.
2. Handling 3
Warning
3. Type designation 4
If these instructions are not observed, it may lead
3.1 Type key for CR, CRI, CRN 1s, 1, 3, 5, 10, 15 and 20 4
to electric shock with consequent risk of serious
3.2 Type key for CR, CRN 32, 45, 64, 90, 120 and 150 4
personal injury or death.
4. Applications 4
5. Technical data 4 If these safety instructions are not observed, it
5.1 Ambient temperature and altitude 4 Caution may result in malfunction or damage to the
5.2 Liquid temperature 5 equipment.
5.3 Maximum permissible operating pressure and liquid
temperature for the shaft seal 5 Notes or instructions that make the job easier
Note
5.4 Minimum inlet pressure 5 and ensure safe operation.
5.5 Maximum inlet pressure 6
5.6 Minimum flow rate 6 2. Handling
5.7 Electrical data 6 When lifting the entire pump with motor, follow these instructions:
5.8 Frequency of starts and stops 6 • Pump with motor sizes 0.37 - 7.5 kW:
5.9 Dimensions and weights 6 Lift the pump in the motor flange by means of straps or the
5.10 Sound pressure level 6 like.
6. Installation 6 • Pump with motor sizes 11-75 kW:
6.1 Foundation 7 Lift the pump by means of the motor eyebolts.
6.2 Vibration dampening 7
6.3 Outdoor installation 8
6.4 Hot surfaces 8
6.5 Torques 8
6.6 Flange forces and torques 8
7. Electrical connection 9
7.1 Cable entry/screwed connection 9
7.2 Three-phase connection 9
7.3 Single-phase connection 10
TM04 0339 0608
Warning
Prior to installation, read these installation and
operating instructions. Installation and operation
must comply with local regulations and accepted
codes of good practice.
3
3. Type designation 5. Technical data
English (GB)
3.1 Type key for CR, CRI, CRN 1s, 1, 3, 5, 10, 15 and 20 5.1 Ambient temperature and altitude
4
5.2 Liquid temperature 5.4 Minimum inlet pressure
English (GB)
The table on page 15 states the relationship between liquid
temperature range and maximum permissible operating pressure.
p [bar]
Hv
35
30 Fig. 4 Schematic view of open system with a CR pump
25
H H H H H
20 Q Q Q HQQE/V Q B The maximum suction lift "H" in metres head can be calculated as
15 Q Q Q Q Q follows:
HBQE/V
5
5.5 Maximum inlet pressure 6. Installation
English (GB)
The table on page 16 states the maximum permissible inlet The pump must be secured to a horizontal, plane and solid
pressure. However, the actual inlet pressure + maximum pump foundation by bolts through the holes in the base plate.
pressure (at no flow) must always be lower than the values stated When installing the pump, follow the procedure below in order to
in fig. A, page 15. avoid damaging the pump.
The pumps are pressure-tested at a pressure of 1.5 times the
values stated in fig. B, page 16. Step Action
1
5.6 Minimum flow rate
Due to the risk of overheating, do not use the pump at flows
below the minimum flow rate. Arrows on the pump base show
6
Fit a vacuum valve close to the
pump if the installation has one
of these characteristics:
• The discharge pipe slopes
downwards away from the
pump.
TM02 0115 3800
6
6.1 Foundation
English (GB)
The foundation/installation must be carried out in
accordance with the following instructions.
Note
Non-compliance may result in functional faults
Vibration dampers
TM04 0343 0608
7
6.3 Outdoor installation 6.6 Flange forces and torques
English (GB)
When installed outdoors, it is recommended to provide the motor If not all loads reach the maximum permissible value stated in the
with a rain cover. We also recommend to open one of the drain tables below, one of these value may exceed the normal limit.
holes in the motor flange. Contact Grundfos for further information.
Warning
When pumping hot liquids, care should be taken
to ensure that persons cannot accidentally come
into contact with hot surfaces.
Figure 12 shows which pump parts get as hot as the pumped
liquid.
Fig. 12 Hot surfaces on a CR, CRI, CRN pump Y-direction: Direction of chamber stack
6.5 Torques Z-direction: 90 ° from inlet/outlet
The table shows the recommended torques for bolts in base and X-direction: Inlet/outlet
flanges. Forces
Base Flange
Y-direction
X-direction
Flange, DN
Z-direction
1s to 5 40 50-60
Force,
Force,
Force,
[mm]
10 to 20 50 60-70
[N]
[N]
[N]
32 to 150 70 70-80
25/32 1s to 5 760 1170 780
40 10 1000 1250 1100
50 15 and 20 1350 1650 1500
65 32 1700 2075 1875
80 45 2050 2500 2250
100 64 and 90 2700 3350 3000
125/150 120 and 150 2700 3350 3000
Torques
CR, CRI, CRN
Y-direction
X-direction
Flange, DN
Z-direction
Torque,
Torque,
Torque,
[mm]
[Nm]
[Nm]
[Nm]
8
7. Electrical connection 7.2 Three-phase connection
English (GB)
The electrical connection should be carried out by an authorised
electrician in accordance with local regulations. Mains supply [V]
The user is to consider whether it is necessary to 1) 60 Hz motors, 0.37 - 1.1 kW: 220-277/380-440 V.
Caution
install an emergency stop switch.
The operating voltage and frequency are marked on the motor
W2 U1 W2 U2 V2
nameplate. Make sure that the motor is suitable for the power
supply on which it will be used and the motor terminal connection
9
7.3 Single-phase connection 7.4 Terminal box position
English (GB)
8. Start-up
TM04 0345 0608
Warning
Fig. 18 Connection, "low voltage", 1.1 - 2.2 kW Pay attention to the direction of the vent hole and
take care to ensure that the escaping water does
not cause injury to persons or damage to the
motor or other components.
In hot-water installations, pay special attention to
the risk of injury caused by scalding hot water.
Follow the instructions on page 28.
TM04 0344 0608
10
8.1 Shaft seal run-in 10. Frost protection
English (GB)
The seal faces are lubricated by the pumped liquid, meaning that Pumps which are not being used during periods of frost should be
there may be a certain amount of leakage from the shaft seal. drained to avoid damage.
When the pump is started up for the first time, or when a new Drain the pump by loosening the vent screw in the pump head
shaft seal is installed, a certain run-in period is required before and by removing the drain plug from the base.
the leakage is reduced to an acceptable level. The time required
for this depends on the operating conditions, i.e. every time the Warning
operating conditions change, a new run-in period will be started. Pay attention to the direction of the vent hole and
Under normal conditions, the leaking liquid will evaporate. As a take care to ensure that the escaping water does
result, no leakage will be detected. not cause injury to persons or damage to the
motor or other components.
However, liquids such as kerosene will not evaporate.
In hot-water installations, pay special attention to
The leakage may therefore be seen as a shaft seal failure.
the risk of injury caused by scalding hot water.
9. Maintenance Do not tighten the vent screw and replace the drain plug until the
pump is to be used again.
Warning CR, CRI, CRN 1s to 5
Before starting work on the pump, make sure that Before replacing the drain plug in the base, screw the bypass
all power supplies to the pump have been valve out against the stop. See fig. 20.
switched off and that they cannot be accidentally
switched on.
Pump bearings and shaft seal are maintenance-free.
Motor bearings Drain plug
Motors not fitted with grease nipples are maintenance-free. Bypass valve
Motors fitted with grease nipples should be lubricated with a high-
temperature, lithium-based grease. See the instructions on the
fan cover.
In the case of seasonal operation (motor is idle for more than
6 months of the year), we recommend you to grease the motor
when the pump is taken out of operation.
Depending on the ambient temperature, the motor bearings must
11 - 18.5 4500 3400 2500 1700 1100 If a pump has been used for a liquid which is
Note toxic or injurious to health, the pump will be
22 4000 3100 2300 1500 1000 classified as contaminated.
30 - 55 4000 3000 2000 1500 - If Grundfos is requested to service the pump, Grundfos must be
contacted with details about the pumped liquid, etc. before the
75 2000 1500 1000 500 - pump is returned for service. Otherwise Grundfos can refuse to
accept the pump for service.
Intervals for 4-pole motors are twice as long as those for 2-pole
Possible costs of returning the pump are to be paid by the
motors.
customer.
If the ambient temperature is lower than 40 °C, bearings must be
However, any application for service (no matter to whom it may
replaced/lubricated at the intervals mentioned under 40 °C.
be made) must include details about the pumped liquid if the
pump has been used for liquids which are toxic or injurious to
health.
11
12. Fault finding
English (GB)
Warning
Before removing the terminal box cover and before removing/dismantling the pump, make sure that the power
supply has been switched off and that it cannot be accidentally switched on.
13. Disposal
This product or parts of it must be disposed of in an
environmentally sound way:
1. Use the public or private waste collection service.
2. If this is not possible, contact the nearest Grundfos company
or service workshop.
Subject to alterations.
12
NPSH
Appendix
TM02 7125 2703 TM01 9884 3801 TM01 9883 3300 TM01 9882 3801 TM02 7387 3403
TM01 1936 0899 TM01 1935 0899 TM01 1934 0899 TM02 7127 2703 TM02 7126 2703
1
13
Appendix
Appendix
14
TM03 8765 2507 TM03 8764 2507 TM01 1937 0899
Fig. A
Appendix
Maximum permissible operating pressure / liquid temperature range
15
Appendix
Fig. B
50 Hz 60 Hz
CR, CRN 32
CR, CRN 32-1-1 → CR, CRN 32-4 4 bar CR, CRN 32-1-1 → CR, CRN 32-2 4 bar
CR, CRN 32-5-2 → CR, CRN 32-10 10 bar CR, CRN 32-3-2 → CR, CRN 32-6 10 bar
CR, CRN 32-11-2 → CR, CRN 32-14 15 bar CR, CRN 32-7-2 → CR, CRN 32-10-2 15 bar
CR, CRN 45
CR, CRN 45-1-1 → CR, CRN 45-2 4 bar CR, CRN 45-1-1 → CR, CRN 45-1 4 bar
CR, CRN 45-3-2 → CR, CRN 45-5 10 bar CR, CRN 45-2-2 → CR, CRN 45-3 10 bar
CR, CRN 45-6-2 → CR, CRN 45-13-2 15 bar CR, CRN 45-4-2 → CR, CRN 45-7 15 bar
CR, CRN 64
CR, CRN 64-1-1 → CR, CRN 64-2-2 4 bar CR, CRN 64-1-1 4 bar
CR, CRN 64-2-1 → CR, CRN 64-4-2 10 bar CR, CRN 64-1 → CR, CRN 64-2-1 10 bar
CR, CRN 64-4-1 → CR, CRN 64-8-1 15 bar CR, CRN 64-2 → CR, CRN 64-5-2 15 bar
CR, CRN 90
CR, CRN 90-1-1 → CR, CRN 90-1 4 bar CR, CRN 90-1-1 → CR, CRN 90-2-2 10 bar
CR, CRN 90-2-2 → CR, CRN 90-3-2 10 bar CR, CRN 90-2-1 → CR, CRN 90-4-2 15 bar
CR, CRN 90-3 → CR, CRN 90-6 15 bar
16
Oval PJE CLAMP - FlexiClamp UNION DIN - FGJ
Fig. C
D D DN 4xø
D
Pump
H
H
H
H
Type L1 B1
L L L D L L L2 B2
L H D L H D L H D L H D L H L1 L2 B1 B2 ∅
[mm] [mm] [Rp] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [G] [mm] [mm] DN [mm] [mm] [mm] [mm] [mm]
CRI, CRN 1s - - - 210 50 42.2 162 50 30 228 50 2 250 75 25/32 100 150 180 220 13
CRI, CRN 1 - - - 210 50 42.2 162 50 30 228 50 2 250 75 25/32 100 150 180 220 13
CRI, CRN 3 - - - 210 50 42.2 162 50 30 228 50 2 250 75 25/32 100 150 180 220 13
CRI, CRN 5 - - - 210 50 42.2 162 50 30 228 50 2 250 75 25/32 100 150 180 220 13
CRI, CRN 10 - - - 261 80 60.1 202 80 50 - - - 280 80 40 130 200 215 248 13
CRI, CRN 15 - - - 261 90 60.1 202 90 50 - - - 300 90 50 130 200 215 248 13
CRI, CRN 20 - - - 261 90 60.1 202 90 50 - - - 300 90 50 130 200 215 248 13
17
Appendix
Appendix
Fig. D
50 Hz 60 Hz
Motor
[kW] LpA LpA
[dB(A)] [dB(A)]
0.37 50 55
0.55 50 53
0.75 50 54
1.1 52 57
1.5 54 59
2.2 54 59
3.0 55 60
4.0 62 66
5.5 60 65
7.5 60 65
11 60 65
15 60 65
18.5 60 65
22 66 70
30 71 75
37 71 75
45 71 75
55 71 75
75 73 77
Fig. E
tm Hv
(°C) (m)
190 126
180 100
170 79
160 62
150 45
40
140 35
30
130
25
120 20
110 15
12
100 10
8,0
90
6,0
80 5,0
4,0
70 3,0
60 2,0
1,5
50
1,0
40 0,8
0,6
30 0,4
TM02 7445 3503
0,3
20
0,2
10
0,1
0
18
CR, CRI, CRN 1s, 1, 3 and 5
Appendix
Fig. F
A B
M6 - 13 Nm
M8 - 31 Nm
M10 - 62 Nm
M5 - 2.5 Nm
x
19
Appendix
A B
C D
TM02 7923 4403
M6 - 13 Nm
M8 - 31 Nm
M10 - 62 Nm
TM02 8542 0404
20
C
B
A
Fig. H
1
CR, CRN 32, 45, 64, 90
1.7 mm
21
Appendix
Appendix
E
C
A
22
Fig. I
CR, CRN 120 and 150
F
D
B
23
Appendix
50a
51
36a
10a
8 9
10 49
64
105 65
4 45
7a
2 2 7 2
100 28 18
23 100 49
28 36
66a 64a
65
7
76a 4a 45
7a 76
60 26 47a
77 77
49
64c
37
66
67
65
5a 45
55
6 6
37
38
35 12 39 25
203
201
6 6 6
38 25
TM02 0455 3403
56 56 56
24
CR, CRI, CRN 10, 15 and 20
Appendix
36a 51
62
61
69
10a
8 9 3
10
49
49c
10a
1 8 9 64
10
65
28a 45 4
105
18
2 2 2
100
28 36
23 66a
100 49
7 49c
76a
7 7a 76 64
65
26
45 4
77 77
60
37
80
49
49c
64a
65
45 4a
55
47a
37 64d
49
6 6 49c
38a
64b
25 64c
39 66
38 67
12
35 65
45 44a
203
201
6 6 6 26a
38a
44b
TM02 7383 3403
25
26c
38
26b
56 56 56
25
Appendix
48
49b
49
28a 49c
51
65
26b 45 45a
26c
9
7 8
4
3
47c
47d
7a 47c
1a 47d
26a
48
28
49b
36a 7a
48 49
7 49b 49c
65
7a 49a
58a 49c
105 45 45a
58
36 65 44
66a
76 45 45a
100 2
18 23
100 4a
37
60
47 47b 51
26 47e 66
66b
47a 67
37
55
31
32
6g
21
6
38a
31 38
32
6g
21
38a 6
21 38
38a 203 201 25
TM01 9996 3600
25
38
25
203 201 56
26
CR, CRN 120 and 150
27
Appendix
Appendix
7
5
3
1
28
Start-up
Appendix
TM01 1409 4497 TM01 1407 4497 TM01 1405 4497 TM01 1403 4497
8
6
4
2
?
TM01 9988 3600 TM01 1408 4497 TM01 1406 4497 TM01 1404 4497
1
Quickguide
Appendix
Start-up
1 2
Close the isolating valve on the discharge side of the pump and Remove the priming plug from the pump head and slowly fill the
open the isolating valve on the suction side. pump with liquid. Replace the priming plug and tighten securely.
3 4
See the correct direction of rotation of the pump on the motor fan Start the pump and check the direction of rotation.
cover.
5 6
Vent the pump by means of the vent valve in the pump head. At the Continue to vent the pump. At the same time, open the discharge
same time, open the discharge isolating valve a little. isolating valve a little more.
7 8
Close the vent valve when a steady stream of liquid runs out of it. For further information, see page 10.
Completely open the discharge isolating valve.
启动
1 2
关闭水泵排出侧的隔离阀,打开吸入侧的隔离阀。 从泵头拆去引水塞并缓慢加注水泵。 装好引水塞并安全拧紧。
3 4
在电机风扇盖上察看水泵正确的转动方向。 启动水泵,检查转动方向。
5 6
通过位于泵头内的除气阀对泵除气。 与此同时,稍稍打开排出侧隔离 水泵继续除气。 与此同时,再稍大些打开排出侧隔离阀。
阀。
7 8
在看到液体持续平稳地从除气阀流出后关闭此阀。 进一步信息请见第22页。
完全打开排出侧隔离阀。
29
30
Argentina Finland Lithuania South Africa
Grundfos companies
Bombas GRUNDFOS de Argentina S.A. OY GRUNDFOS Pumput AB GRUNDFOS Pumps UAB GRUNDFOS (PTY) LTD
Ruta Panamericana km. 37.500 Centro Mestarintie 11 Smolensko g. 6 Corner Mountjoy and George Allen Roads
Industrial Garin FIN-01730 Vantaa LT-03201 Vilnius Wilbart Ext. 2
1619 Garín Pcia. de B.A. Phone: +358-(0)207 889 900 Tel: + 370 52 395 430 Bedfordview 2008
Phone: +54-3327 414 444 Telefax: +358-(0)207 889 550 Fax: + 370 52 395 431 Phone: (+27) 11 579 4800
Telefax: +54-3327 45 3190 Fax: (+27) 11 455 6066
France Malaysia E-mail: lsmart@grundfos.com
Australia Pompes GRUNDFOS Distribution S.A. GRUNDFOS Pumps Sdn. Bhd.
GRUNDFOS Pumps Pty. Ltd. Parc d’Activités de Chesnes 7 Jalan Peguam U1/25 Spain
P.O. Box 2040 57, rue de Malacombe Glenmarie Industrial Park Bombas GRUNDFOS España S.A.
Regency Park F-38290 St. Quentin Fallavier (Lyon) 40150 Shah Alam Camino de la Fuentecilla, s/n
South Australia 5942 Tél.: +33-4 74 82 15 15 Selangor E-28110 Algete (Madrid)
Phone: +61-8-8461-4611 Télécopie: +33-4 74 94 10 51 Phone: +60-3-5569 2922 Tel.: +34-91-848 8800
Telefax: +61-8-8340 0155 Telefax: +60-3-5569 2866 Telefax: +34-91-628 0465
Germany
Austria GRUNDFOS GMBH Mexico Sweden
GRUNDFOS Pumpen Vertrieb Ges.m.b.H. Schlüterstr. 33 Bombas GRUNDFOS de México S.A. de GRUNDFOS AB
Grundfosstraße 2 40699 Erkrath C.V. Box 333 (Lunnagårdsgatan 6)
A-5082 Grödig/Salzburg Tel.: +49-(0) 211 929 69-0 Boulevard TLC No. 15 431 24 Mölndal
Tel.: +43-6246-883-0 Telefax: +49-(0) 211 929 69-3799 Parque Industrial Stiva Aeropuerto Tel.: +46 31 332 23 000
Telefax: +43-6246-883-30 e-mail: infoservice@grundfos.de Apodaca, N.L. 66600 Telefax: +46 31 331 94 60
Service in Deutschland: Phone: +52-81-8144 4000
Belgium e-mail: kundendienst@grundfos.de Telefax: +52-81-8144 4010 Switzerland
N.V. GRUNDFOS Bellux S.A. GRUNDFOS Pumpen AG
Boomsesteenweg 81-83 HILGE GmbH & Co. KG Netherlands Bruggacherstrasse 10
B-2630 Aartselaar Hilgestrasse 37-47 GRUNDFOS Netherlands CH-8117 Fällanden/ZH
Tél.: +32-3-870 7300 55292 Bodenheim/Rhein Veluwezoom 35 Tel.: +41-44-806 8111
Télécopie: +32-3-870 7301 Germany 1326 AE Almere Telefax: +41-44-806 8115
Tel.: +49 6135 75-0 Postbus 22015
Belarus Telefax: +49 6135 1737 1302 CA ALMERE Taiwan
Представительство ГРУНДФОС в e-mail: hilge@hilge.de Tel.: +31-88-478 6336 GRUNDFOS Pumps (Taiwan) Ltd.
Минске Telefax: +31-88-478 6332 7 Floor, 219 Min-Chuan Road
220125, Минск Greece E-mail: info_gnl@grundfos.com Taichung, Taiwan, R.O.C.
ул. Шафарнянская, 11, оф. 56, БЦ GRUNDFOS Hellas A.E.B.E. Phone: +886-4-2305 0868
«Порт» 20th km. Athinon-Markopoulou Av. New Zealand Telefax: +886-4-2305 0878
Тел.: +7 (375 17) 286 39 72/73 P.O. Box 71 GRUNDFOS Pumps NZ Ltd.
Факс: +7 (375 17) 286 39 71 GR-19002 Peania 17 Beatrice Tinsley Crescent Thailand
E-mail: minsk@grundfos.com Phone: +0030-210-66 83 400 North Harbour Industrial Estate GRUNDFOS (Thailand) Ltd.
Telefax: +0030-210-66 46 273 Albany, Auckland 92 Chaloem Phrakiat Rama 9 Road,
Bosna and Herzegovina Phone: +64-9-415 3240 Dokmai, Pravej, Bangkok 10250
GRUNDFOS Sarajevo Hong Kong Telefax: +64-9-415 3250 Phone: +66-2-725 8999
Zmaja od Bosne 7-7A, GRUNDFOS Pumps (Hong Kong) Ltd. Telefax: +66-2-725 8998
BH-71000 Sarajevo Unit 1, Ground floor Norway
Phone: +387 33 592 480 Siu Wai Industrial Centre GRUNDFOS Pumper A/S Turkey
Telefax: +387 33 590 465 29-33 Wing Hong Street & Strømsveien 344 GRUNDFOS POMPA San. ve Tic. Ltd. Sti.
www.ba.grundfos.com 68 King Lam Street, Cheung Sha Wan Postboks 235, Leirdal Gebze Organize Sanayi Bölgesi
e-mail: grundfos@bih.net.ba Kowloon N-1011 Oslo Ihsan dede Caddesi,
Phone: +852-27861706 / 27861741 Tlf.: +47-22 90 47 00 2. yol 200. Sokak No. 204
Brazil Telefax: +852-27858664 Telefax: +47-22 32 21 50 41490 Gebze/ Kocaeli
BOMBAS GRUNDFOS DO BRASIL Phone: +90 - 262-679 7979
Av. Humberto de Alencar Castelo Branco, Hungary Poland Telefax: +90 - 262-679 7905
630 GRUNDFOS Hungária Kft. GRUNDFOS Pompy Sp. z o.o. E-mail: satis@grundfos.com
CEP 09850 - 300 Park u. 8 ul. Klonowa 23
São Bernardo do Campo - SP H-2045 Törökbálint, Baranowo k. Poznania Ukraine
Phone: +55-11 4393 5533 Phone: +36-23 511 110 PL-62-081 Przeźmierowo Бізнес Центр Європа
Telefax: +55-11 4343 5015 Telefax: +36-23 511 111 Tel: (+48-61) 650 13 00 Столичне шосе, 103
Fax: (+48-61) 650 13 50 м. Київ, 03131, Україна
Bulgaria India Телефон: (+38 044) 237 04 00
Grundfos Bulgaria EOOD GRUNDFOS Pumps India Private Limited Portugal Факс.: (+38 044) 237 04 01
Slatina District 118 Old Mahabalipuram Road Bombas GRUNDFOS Portugal, S.A. E-mail: ukraine@grundfos.com
Iztochna Tangenta street no. 100 Thoraipakkam Rua Calvet de Magalhães, 241
BG - 1592 Sofia Chennai 600 096 Apartado 1079 United Arab Emirates
Tel. +359 2 49 22 200 Phone: +91-44 2496 6800 P-2770-153 Paço de Arcos GRUNDFOS Gulf Distribution
Fax. +359 2 49 22 201 Tel.: +351-21-440 76 00 P.O. Box 16768
email: bulgaria@grundfos.bg
Indonesia Telefax: +351-21-440 76 90 Jebel Ali Free Zone
PT GRUNDFOS Pompa Dubai
Canada Jl. Rawa Sumur III, Blok III / CC-1 Romania Phone: +971 4 8815 166
GRUNDFOS Canada Inc. Kawasan Industri, Pulogadung GRUNDFOS Pompe România SRL Telefax: +971 4 8815 136
2941 Brighton Road Jakarta 13930 Bd. Biruintei, nr 103
Oakville, Ontario Phone: +62-21-460 6909 Pantelimon county Ilfov United Kingdom
L6H 6C9 Telefax: +62-21-460 6910 / 460 6901 Phone: +40 21 200 4100 GRUNDFOS Pumps Ltd.
Phone: +1-905 829 9533 Telefax: +40 21 200 4101 Grovebury Road
Telefax: +1-905 829 9512
Ireland E-mail: romania@grundfos.ro Leighton Buzzard/Beds. LU7 4TL
GRUNDFOS (Ireland) Ltd. Phone: +44-1525-850000
China Unit A, Merrywell Business Park Russia Telefax: +44-1525-850011
GRUNDFOS Pumps (Shanghai) Co. Ltd. Ballymount Road Lower ООО Грундфос Россия
50/F Maxdo Center No. 8 XingYi Rd. Dublin 12 109544, г. Москва, ул. Школьная, 39-41, U.S.A.
Hongqiao development Zone Phone: +353-1-4089 800 стр. 1 GRUNDFOS Pumps Corporation
Shanghai 200336 Telefax: +353-1-4089 830 Тел. (+7) 495 564-88-00 (495) 737-30-00 17100 West 118th Terrace
PRC Факс (+7) 495 564 88 11 Olathe, Kansas 66061
Phone: +86 21 612 252 22
Italy E-mail grundfos.moscow@grundfos.com Phone: +1-913-227-3400
Telefax: +86 21 612 253 33 GRUNDFOS Pompe Italia S.r.l. Telefax: +1-913-227-3500
Via Gran Sasso 4 Serbia
Croatia I-20060 Truccazzano (Milano) Grundfos Srbija d.o.o. Uzbekistan
GRUNDFOS CROATIA d.o.o. Tel.: +39-02-95838112 Omladinskih brigada 90b Grundfos Tashkent, Uzbekistan The Repre-
Buzinski prilaz 38, Buzin Telefax: +39-02-95309290 / 95838461 11070 Novi Beograd sentative Office of Grundfos Kazakhstan in
HR-10010 Zagreb Phone: +381 11 2258 740 Uzbekistan
Phone: +385 1 6595 400
Japan Telefax: +381 11 2281 769 38a, Oybek street, Tashkent
Telefax: +385 1 6595 499 GRUNDFOS Pumps K.K. www.rs.grundfos.com Телефон: (+998) 71 150 3290 / 71 150
www.hr.grundfos.com Gotanda Metalion Bldg., 5F, 3291
5-21-15, Higashi-gotanda Singapore Факс: (+998) 71 150 3292
Czech Republic Shiagawa-ku, Tokyo GRUNDFOS (Singapore) Pte. Ltd.
GRUNDFOS s.r.o. 141-0022 Japan 25 Jalan Tukang Addresses Revised 21.05.2014
Čajkovského 21 Phone: +81 35 448 1391 Singapore 619264
779 00 Olomouc Telefax: +81 35 448 9619 Phone: +65-6681 9688
Phone: +420-585-716 111 Telefax: +65-6681 9689
Telefax: +420-585-716 299
Korea
GRUNDFOS Pumps Korea Ltd. Slovakia
Denmark 6th Floor, Aju Building 679-5 GRUNDFOS s.r.o.
GRUNDFOS DK A/S Yeoksam-dong, Kangnam-ku, 135-916 Prievozská 4D
Martin Bachs Vej 3 Seoul, Korea 821 09 BRATISLAVA
DK-8850 Bjerringbro Phone: +82-2-5317 600 Phona: +421 2 5020 1426
Tlf.: +45-87 50 50 50 Telefax: +82-2-5633 725 sk.grundfos.com
Telefax: +45-87 50 51 51
E-mail: info_GDK@grundfos.com
Latvia Slovenia
SIA GRUNDFOS Pumps Latvia GRUNDFOS d.o.o.
www.grundfos.com/DK
Deglava biznesa centrs Šlandrova 8b, SI-1231 Ljubljana-Črnuče
Estonia Augusta Deglava ielā 60, LV-1035, Rīga, Phone: +386 31 718 808
GRUNDFOS Pumps Eesti OÜ Tālr.: + 371 714 9640, 7 149 641 Telefax: +386 (0)1 5680 619
Peterburi tee 92G Fakss: + 371 914 9646 E-mail: slovenia@grundfos.si
11415 Tallinn
Tel: + 372 606 1690
Fax: + 372 606 1691
ECM: 1104018
97688538 1112
www.grundfos.com
The name Grundfos, the Grundfos logo, and be think innovate are registered trademarks owned by Grundfos Holding A/S or Grundfos A/S, Denmark. All rights reserved worldwide. © Copyright Grundfos Holding A/S