Documente Academic
Documente Profesional
Documente Cultură
Contents
Project: Model: Chk’d: Date:
Model DVFU
Section Page
Specifications 2-217
Selection Chart 2-217
Performance Curves 2-222
Outline Drawings 2-232
Sectional View 2-245
QDC Information 2-278
Technical Information 2-289.1
material specification
impeller description
motor protection
cable entry
paint specifications
mechanical seal
general
Motor Data 2-315.1
motor electrical specifications
cable data
wiring diagrams
motor electrical data
80 DVF U 6 1.5 2
DISCHARGE SIZE – mm
50mm – 2"
80mm – 3"
100mm – 4"
150mm – 6"
MODEL TYPE
DVF – submersible vortex sewage pump
DVFM – FM explosion proof designation
GEOGRAPHIC DESIGNATION
U – U.S.A. market
HERTZ
6 – 60
RATED KW
1.5 – 2HP 11 – 15HP
2.2 – 3HP 15 – 20HP
3.7 – 5HP 18 – 25HP
5.5 – 71/2HP 22 – 30HP
7.5 – 10HP
PHASE
none – three phase
VOLTAGE
2 - 208/230
4 - 460
5 - 575
Standard Optional
Size 2, 3, 4, 6 inch
Range of HP 2 to 30 HP
Range of Performance Capacity 16 to 1200 GPM
Head 13 to 121 feet
Limitation
Maximum Water Temperature 104°F (40°C)
Synchronous Speed 1800 RPM
Materials
Casing Cast Iron
Impeller Cast Iron
Shaft 403 Stainless Steel for 2 to 5HP
420 Stainless Steel for 71/2 to 30HP
Motor Frame Cast Iron
Fastener 304 Stainless Steel
Mechanical Seal Double Mechanical Seal
Material – Upper Side Carbon/Ceramic
Material – Lower Side Silicon Carbide/Silicon Carbide
Impeller Type Recessed Vortex Impeller
Bearing Prelubricated Ball Bearing
Motor Insulation Class F FM Explosion Proof, Class 1,
Three Phase 208/230V, 460V Division 1, Group C, D
Motor Protection Built-in Thermal Detector – Klixons
Built-in Leakage Detector
Submersible cable 33 ft. (2 to 5 HP) ____ ft. (customer specified)
Accessories 40 ft. (71/2 to 30 HP) QDC System
6 7
8
80DVCFU611 15HP
80DVBFU611 15HP 14
80DVFU67.5 10HP 15
13
5 12
50DVFU62.2 3HP 4 16
11
2
3 10 17
50DVFU61.5 2HP
9
1
80DVFU61.5 2HP
B. Manufacturer:
EBARA International Corporation
C. Pump Characteristics:
Pumps shall conform to the following requirements:
Number of units
Design flow (gpm)
Design TDH (ft)
Minimum shut off head (ft)
RPM 1800
Maximum HP
Minimum efficiency at design (%)
Minimum power factor at design (%)
Voltage/HZ 208/230V, 460V / 60
Phase 3
D. Pump Construction:
All major parts of the pumping unit(s) including casing, impeller, motor frame and discharge elbow shall be manufactured
from gray cast iron, ASTM A-48 Class 30. Castings shall have smooth surfaces devoid of blow holes or other casting
irregularities. Casing design shall be centerline discharge with a large radius on the cut water to prevent clogging.
Units shall be furnished with a discharge elbow and 125 lb. flat face ANSI flange. All exposed bolts and nuts shall be
304 stainless steel. All mating surfaces of major components shall be machined and fitted with NBR O-rings where
watertight sealing is required. Machining and fitting shall be such that sealing is accomplished by automatic compression
of O-rings in two planes and O-ring contact is made on four surfaces without the requirement of specific torque limits.
Internal and external surfaces are prepared to SPPC-VISI-SP-3-63 then coated with a zinc-chromate primer. The
external surfaces are then coated with an H.B. Tnemecol 46-465 Coal Tar paint.
Impeller design shall be a recessed, vortex, multi-vane design, direct connected to the motor shaft with a slip fit, key
driven, and secured with an impeller nut. The inlet edge of the impeller vanes shall be angled toward the impeller
periphery so as to facilitate the release of objects that might otherwise clog the pump. The design shall also include
back pump out vanes to reduce the pressure and entry of foreign materials into the mechanical seal area. In addition,
a lip seal shall be located behind the impeller hub to further reduce the entry of foreign materials into the seal area
on 71/2HP and above.
1. Mechanical Seals:
a. For units 2 to 5 HP, double mechanical seals operating in an oil bath shall be provided on all units. The oil
filled seal chamber shall be designed to prevent over-filling and include an anti-vortexing vane to insure proper
lubrication of both seal faces. Lower face materials shall be silicon carbide, upper faces carbon vs. ceramic,
NBR elastomers, and 304SS hardware. Seal system shall not rely on pumping medium for lubrication.
b. Units 71/2 to 30 HP shall be designed to include a double mechanical seal in a tandem arrangement. Each
seal shall be positively driven and act independently with its own spring system. The upper seal operates in
an oil bath, while the lower seal is lubricated by the oil from between the shaft and the seal faces, and in contact
with the pumpage on the outside. Lower face materials shall be silicon carbide, upper faces carbon vs.
ceramic, NBR elastomers, and 304SS hardware. Seal system shall not rely on pumping medium for lubrication.
Power cable jacket shall be manufactured of an oil resistant chloroprene rubber material, designed for submerged
applications. Cable shall be watertight to a depth of a least 65'. The cable entry system shall comprise of primary,
secondary, and tertiary sealing methods. The primary seal shall be achieved by a cylindrical elastomeric grommet
compressed between the motor cover and a 304SS washer. Secondary sealing is accomplished with a compressed
O-ring made of NBR material. Compression and subsequent sealing shall preclude specific torque requirements. The
system shall also include tertiary sealing to prevent leakage into the motor housing due to capillary action through
the insulation if the cable is damaged or cut. The cable wires shall be cut, stripped, re-connected with a copper butt
end connector, and embedded in epoxy within the cable gland. This provides a dead end for leakage through the
cable insulation into the motor junction area.
Guide rails are not part of the pump package and shall be supplied by others.
The QDC shall be manufactured of cast iron, A48 Class 30. It shall be designed to adequately support the guide
rails, discharge piping, and pumping unit under both static and dynamic loading conditions with support legs that are
suitable for anchoring it to the wetwell floor. The face of the inlet QDC flange shall be perpendicular to the floor of
the wetwell. The discharge flange of the QDC shall conform to ANSI B16.1 Class 125.
The pump design shall include an integral self-aligning sliding bracket. Sealing of the pumping unit to the QDC shall
be accomplished by a single, linear, downward motion of the pump. The entire weight of the pump unit shall be guided
to and wedged tightly against the inlet flange of the QDC, making metal to metal contact with the pump discharge
forming a seal without the use of bolts, gaskets or O-rings.
Lifting chain shall be galvanized (stainless steel) suitable for removing and installing the pump unit.
B. Manufacturer:
EBARA International Corporation
C. Pump Characteristics:
Pumps shall conform to the following requirements:
Number of units
Design flow (gpm)
Design TDH (ft)
Minimum shut off head (ft)
RPM 1800
Maximum HP
Minimum efficiency at design (%)
Minimum power factor at design (%)
Voltage/HZ 208/230V, 460V / 60
Phase 3
D. Pump Construction:
All major parts of the pumping unit(s) including casing, impeller, motor frame and discharge elbow shall be manufactured
from gray cast iron, ASTM A-48 Class 30. Castings shall have smooth surfaces devoid of blow holes or other casting
irregularities. Casing design shall be centerline discharge with a large radius on the cut water to prevent clogging.
Units shall be furnished with a discharge elbow and 125 lb. flat face ANSI flange. All exposed bolts and nuts shall be
304 stainless steel. All mating surfaces of major components shall be machined and fitted with NBR O-rings where
watertight sealing is required. Machining and fitting shall be such that sealing is accomplished by automatic compression
of O-rings in two planes and O-ring contact is made on four surfaces without the requirement of specific torque limits.
Internal and external surfaces are prepared to SPPC-VISI-SP-3-63 then coated with a zinc-chromate primer. The
external surfaces are then coated with an H.B. Tnemecol 46-465 Coal Tar paint.
Impeller design shall be a recessed, vortex, multi-vane design, direct connected to the motor shaft with a slip fit,
key driven, and secured with an impeller nut. The inlet edge of the impeller vanes shall be angled toward the
impeller periphery so as to facilitate the release of objects that might otherwise clog the pump. The design shall also
include back pump out vanes to reduce the pressure and entry of foreign materials into the mechanical seal area. In
addition, a lip seal shall be located behind the impeller hub to further reduce the entry of foreign materials into the
seal area on 71/2HP and above.
1. Mechanical Seals:
a. For units 2 to 5 HP, double mechanical seals operating in an oil bath shall be provided on all units. The oil
filled seal chamber shall be designed to prevent over-filling and include an anti-vortexing vane to insure proper
lubrication of both seal faces. Lower face materials shall be silicon carbide, upper faces carbon vs. ceramic,
NBR elastomers, and 304SS hardware. Seal system shall not rely on pumping medium for lubrication.
b. Units 71/2 to 30 HP shall be designed to include a double mechanical seal in a tandem arrangement. Each
seal shall be positively driven and act independently with its own spring system. The upper seal operates in
an oil bath, while the lower seal is lubricated by the oil from between the shaft and the seal faces, and in contact
with the pumpage on the outside. Lower face materials shall be silicon carbide, upper faces carbon vs.
ceramic, NBR elastomers, and 304SS hardware. Seal system shall not rely on pumping medium for lubrication.
Power cable jacket shall be manufactured of an oil resistant chloroprene rubber material, designed for submerged
applications. Cable shall be watertight to a depth of a least 65'. The cable entry system shall comprise of primary,
secondary, and tertiary sealing methods. The primary seal shall be achieved by a cylindrical elastomeric grommet
compressed between the motor cover and a 304SS washer. Secondary sealing is accomplished with a compressed
O-ring made of NBR material. Compression and subsequent sealing shall preclude specific torque requirements. The
system shall also include tertiary sealing to prevent leakage into the motor housing due to capillary action through
the insulation if the cable is damaged or cut. The cable wires shall be cut, stripped, re-connected with a copper butt
end connector, and embedded in epoxy within the cable gland. This provides a dead end for leakage through the
cable insulation into the motor junction area.
The QDC shall be manufactured of cast iron, A48 Class 30. It shall be designed to adequately support the guide
rails, discharge piping, and pumping unit under both static and dynamic loading conditions with support legs that are
suitable for anchoring it to the wetwell floor. The face of the inlet QDC flange shall be perpendicular to the floor of
the wetwell. The discharge flange of the QDC shall conform to ANSI B16.1 Class 125.
The pump design shall include an integral self-aligning sliding bracket. Sealing of the pumping unit to the QDC shall
be accomplished by a single, linear, downward motion of the pump. The entire weight of the pump unit shall be guided
to and wedged tightly against the inlet flange of the QDC, making metal to metal contact with the pump discharge
forming a seal without the use of bolts, gaskets or O-rings.
Lifting chain shall be galvanized (stainless steel) suitable for removing and installing the pump unit.
30
Total Head (Ft)
40 20
30 EFFICIENCY
10 1
0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 120 130
Capacity USGPM
30
50
40 20 EFFICIENCY
Brake Horsepower (BHP)
30
20 10
BHP 3
10 2
1
0 0 0
0 20 40 60 80 100 120 140 160
Capacity USGPM
60
40
10 1
0 0 0
0 20 40 60 80 100 120 140 160 180 200 220
Capacity USGPM
50 20
Min. Dia. 130mm
Total Head (Ft)
Efficiency (%)
EFFICIENCY
40
30
Brake Horsepower (BHP)
10
20
3
BHP
10 2
0 0 0
0 40 80 120 160 200 240 280 320 360
Capacity USGPM
30
50 20
40
Capacity USGPM
30
50 20
EFFICIENCY
40
Brake Horsepower (BHP)
30
10 5
20 BHP 4
3
10 2
1
0 0 0
0 40 80 120 160 200 240 280 320 360
Capacity USGPM
EFFICIENCY
40 40
Total Head (Ft)
Efficiency (%)
10 10 5
BHP 4
3
2
1
0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300
Capacity USGPM
40
Total Head (Ft)
30
50
EFFICIENCY
Brake Horsepower (BHP)
40 20 8
BHP
30 6
20 10 4
10 2
0 0 0
0 100 200 300 400
Capacity USGPM
50 50
Efficiency (%)
40 40
20 20 10
BHP
10 10 5
0 0 0
0 100 200 300 400 500
Capacity USGPM
60
50 50
Efficiency (%)
40 40
EFFICIENCY
30 30
Brake Horsepower (BHP)
20 20
BHP 15
10 10 10
5
0 0 0
0 100 200 300 400 500 600
Capacity USGPM
80DVCF611 TO 622 (15 to 30 HP) Synchronous Speed: 1800 RPM 3, 4 inch Discharge
130
D = 269mm Curve No: DV-C612-9203
35 40 Solid Dia 3"
120 LL80
D = 255mm 45
47
49
110 50 51
D = 246mm
52
100
51
Total Head (Ft)
D = 232mm
90 25 HP
D = 214mm
80
20 HP
70
60 15 HP
50
40
0 100 200 300 400 500 600
Capacity USGPM
50 25
Efficiency (%)
EFFICIENCY
40 20
30 15
Brake Horsepower (BHP)
5
20 10 BHP 4
3
10 5 2
1
0 0 0
0 40 80 120 160 200 240 280 320 360 400 440 480
Capacity USGPM
30
MIN. Dia. 157mm
60
50 20
30
10
20 BHP 8
10 4
0 0 0
0 100 200 300 400 500
Capacity USGPM
40 40
Total Head (Ft)
30 30
EFFICIENCY
Brake Horsepower (BHP)
20 20
BHP
10 10 10
0 0 0
0 100 200 300 400 500 600
Capacity USGPM
50 50
MIN. Dia. 187mm
Total Head (Ft)
40 40
Efficiency (%)
30 30
EFFICIENCY
15
BHP
10 10 10
0 0 0
0 100 200 300 400 500 600 700
Capacity USGPM
100DVCF611 to 615 (15 to 20HP) Synchronous Speed: 1800 RPM 3, 4 inch Discharge
80
Curve No: DV-C617-9203
Solid Dia 4"
LL100
D = 212mm
70
D = 201mm 35
40
45 47
60 D = 192mm 48
Total Head (Ft)
49
48
50
40
15 HP
30
20
0 100 200 300 400 500 600 700
Capacity USGPM
100DVDF611 to 622 (15 to 30HP) Synchronous Speed: 1800 RPM 3, 4 inch Discharge
130
D = 269mm Curve No: DV-C618-9203
120 Solid Dia 4"
D = 255mm LL100
35
110 40
45 48
D = 246mm 49 50
51
100 52
D = 232mm
51
Total Head (Ft)
90
80
D = 214mm
70
30 HP
60
15 HP
50
20 HP
25 HP
40
30
20
0 100 200 300 400 500 600 700 800
Capacity USGPM
150DVBF611 to 622 (15 to 30HP) Synchronous Speed: 1800 RPM 4, 6 inch Discharge
70
D = 222mm
Curve No: DV-C619-9203
35 Solid Dia 5"
LL125
60 40
D = 204mm 45 47
49
50 51
50 52
D = 184mm
Total Head (Ft)
40
30
25 HP
20 20 HP
15 HP
10
0
0 100 200 300 400 500 600 700 800 900 1000 1100 1200
Capacity USGPM
150DVCF618 to 622 (25 to 30HP) Synchronous Speed: 1800 RPM 4, 6 inch Discharge
90
D = 269mm Curve No: DV-C620-9203
Solid Dia 5"
LL125
80
D = 254mm 35 40
45
70 47
D = 238mm 49
Total Head (Ft)
50
60 D = 221mm
50
30 HP
40
25 HP
30
20
0 100 200 300 400 500 600 700 800 900 1000 1100
Capacity USGPM
f
e
ø
t
(n) QTY - (h) HOLES
Dimensions: inch
OUTPUT PUMP & MOTOR
PHASE SIZE
ø MODEL WEIGHT
Lb
kW HP A B C D E F G H J L
50DVFU61.5 1.5 2 153/4 93/8 111/16 411/16 81/16 75/16 5
/16 28 57/8 67/8 121
THREE 2
50DVFU62.2 2.2 3 153/4 93/8 111/16 411/16 81/16 75/16 5
/16 29 57/8 67/8 150
Dimensions: mm
OUTPUT PUMP & MOTOR WEIGHT
PHASE SIZE
ø MODEL kg
kW HP A B C D E F G H J L
50DVFU61.5 1.5 2 400 238 281 119 205 185 8 711 150 175 55
THREE 50
50DVFU62.2 2.2 3 400 238 281 119 205 185 8 737 150 175 68
f
e
ø
t
(n) QTY - (h) HOLES
mm
ø e f t n h
50 121 152 16 4 19
80 152 191 19 4 19
100 191 229 24 8 19
Dimensions: inch
OUTPUT PUMP & MOTOR WEIGHT
PHASE SIZE
ø MODEL Lb
kW HP A B C D E F G H J L
80DVFU61.5 1.5 2 1711/16 93/8 131/16 411/16 91/4 813/16 5
/16 297/16 65/16 81/16 130
2/3 80DVCFU62.2 2.2 3 1711/16 93/8 131/16 411/16 91/4 813/16 /16 307/16 65/16 81/4 159
5
Dimensions: mm
OUTPUT PUMP & MOTOR WEIGHT
PHASE SIZE
ø MODEL kg
kW HP A B C D E F G H J L
80DVFU61.5 1.5 2 450 238 331 119 235 224 8 747 160 205 59
50/80 80DVCFU62.2 2.2 3 450 238 331 119 235 224 8 773 160 210 72
80DVCFU63.7 3.7 5 450 238 331 119 235 224 8 813 160 210 78
THREE 80DVBFU62.2 2.2 3 471 252 346 125 250 254 8 820 175 260 80
80/100 80DVBFU63.7 3.7 5 471 252 346 125 250 254 8 860 175 260 80
80DVFU65.5 5.5 71/2 514 285 371 143 275 254 10 994 200 330 119
80DVFU67.5 7.5 10 514 285 371 143 275 254 10 994 200 330 132
*Note: All dimensions are based on 3'' discharge.
EBARA International Corporation
2-233
rev. 01/02
EBARA Submersible Vortex Sewage Pumps DVFU
Dimensions
Project: Model: Chk’d: Date:
Model DVFU
80DVBFU, 15HP
80DVCFU, 15 to 30HP
f
e
ø
t
(n) QTY - (h) HOLES
Dimensions: mm
OUTPUT PUMP & MOTOR WEIGHT
PHASE SIZE
ø MODEL kg
kW HP A B C D E F G H J L
80DVBFU611 11 15 514 285 371 143 275 254 8 1087 200 330 177
80DVCFU611 11 15 582 342 411 171 315 254 8 1087 240 330 184
THREE 80/100 80DVCFU615 15 20 582 342 411 171 315 254 8 1152 240 350 228
80DVCFU618 18.5 25 582 342 411 171 315 254 8 1192 240 350 262
80DVCFU622 22 30 582 342 411 171 315 254 8 1192 240 350 287
*Note: All dimensions are based on 3'' discharge.
EBARA International Corporation
2-234
rev. 01/02
EBARA Submersible Vortex Sewage Pumps DVFU
Dimensions
Project: Model: Chk’d: Date:
Model DVFU
100DVFU, 5 to 10HP
100DVBFU, 15HP
f
e
ø
t
(n) QTY - (h) HOLES
Dimensions: inch
OUTPUT PUMP & MOTOR WEIGHT
PHASE SIZE
ø MODEL Lb
kW HP A B C D E F G H J L
100DVFU63.7 3.7 5 233/16 121/8 171/8 61/16 125/8 12 5
/16 361/16 87/16 123/8 209
100DVFU65.5 5.5 71/2 233/16 121/8 171/8 61/16 125/8 12 3
/8 413/8 87/16 151/4 317
THREE 3/4
100DVFU67.5 7.5 10 233/16 121/8 171/8 61/16 125/8 12 3
/8 413/8 87/16 151/4 346
100DVBFU611 11 15 233/16 121/8 171/8 61/16 125/8 12 5
/16 451/16 87/16 151/4 452
Dimensions: mm
OUTPUT PUMP & MOTOR WEIGHT
PHASE SIZE MODEL kg
kW HP A B C D E F G H J L
100DVFU63.7 3.7 5 589 308 435 154 320 305 8 916 215 315 95
100DVFU65.5 5.5 71/2 589 308 435 154 320 305 10 1051 215 388 144
THREE 80/100
100DVFU67.5 7.5 10 589 308 435 154 320 305 10 1051 215 388 157
100DVBFU611 11 15 589 308 435 154 320 305 8 1144 215 388 205
f
e
ø
t
(n) QTY - (h) HOLES
Dimensions: inch
OUTPUT PUMP & MOTOR WEIGHT
PHASE SIZE
ø MODEL Lb
kW HP A B C D E F G H J L
100DVCFU611 11 15 233/16 121/8 171/8 61/16 125/8 12 5
/16 451/16 87/16 151/4 452
100DVCFU615 15 20 233/16 121/8 171/8 61/16 125/8 12 5
/16 475/8 87/16 1515/16 547
100DVDFU611 11 15 257/16 137/8 181/2 615/16 14 12 5
/16 4415/16 913/16 151/4 445
THREE 3/4
100DVDFU615 15 20 257/16 137/8 181/2 615/16 14 12 5
/16 471/2 913/16 1515/16 547
100DVDFU618 18.5 25 257/16 137/8 181/2 615/16 14 12 5
/16 491/8 913/16 1515/16 602
100DVDFU622 22 30 257/16 137/8 181/2 615/16 14 12 5
/16 491/8 913/16 1515/16 668
Dimensions: mm
OUTPUT PUMP & MOTOR WEIGHT
PHASE SIZE
ø MODEL kg
kW HP A B C D E F G H J L
100DVCFU611 11 15 589 308 435 154 320 305 8 1144 215 388 205
100DVCFU615 15 20 589 308 435 154 320 305 8 1209 215 405 248
100DVDFU611 11 15 646 352 470 176 355 305 8 1142 250 388 202
THREE 80/100
100DVDFU615 15 20 646 352 470 176 355 305 8 1207 250 405 248
100DVDFU618 18.5 25 646 352 470 176 355 305 8 1247 250 405 273
100DVDFU622 22 30 646 352 470 176 355 305 8 1247 250 405 303
f
e
ø
t
(n) QTY - (h) HOLES
Dimensions: mm
OUTPUT PUMP & MOTOR WEIGHT
PHASE SIZE
ø MODEL kg
kW HP A B C D E F G H J L
150DVBFU611 11 15 695 332 525 170 385 401 8 1218 235 480 233
150DVBFU615 15 20 695 332 525 170 385 401 8 1283 235 480 276
150DVBFU618 18.5 25 695 332 525 170 385 401 8 1323 235 480 310
THREE 100/150
150DVBFU622 22 30 695 332 525 170 385 401 8 1323 235 480 335
150DVCFU618 18.5 25 752 384 560 192 420 401 8 1320 270 480 321
150DVCFU622 22 30 752 384 560 192 420 401 8 1320 270 480 346
*Note: All dimensions are based on 6'' discharge.
EBARA International Corporation
2-237
rev. 01/02
EBARA Submersible Vortex Sewage Pumps DVFU
Dimensions
Project: Model: Chk’d: Date:
Model DVFU with Quick Discharge Connector
50DVFU, 2 to 3HP
29/16 (65) 311/2 (800) 29/16 (65)
29/16 (65)
G
13/8 (35)
279/16 (700)
F
29/16 (65)
Guide pipe support
Floor Frame
Manhole dimensions in
Bolt 2– /2 x 1 /16
1 3
floor frame installation
51/2 (140)
39/16 (90)
(12x30)
19/16 (40)
23/16 (56)
23/4 (70)
SGP (W) 1"
Guide pipe length
811/16 (220)
ø2
61/2 (165)
55/16 (135)
(50
t
)
31/8 (80)
Bolt 2 – 5/8 (16) Flange (ANSI 125 PSI F.F)
51/4 (132) 711/16 (195)
inch
ø e f t n h
315/16 (100) 2 43/4 6 5
/8 4 3
/4
mm
ø e f t n h
50 121 152 16 4 19
Dimensions: inch
SIZE OUTPUT Q.D.C. PUMP & MOTOR WEIGHT Lb
PHASE ø MODEL
kW HP MODEL F G Q T PUMP Q.D.C.
50DVFU61.5 1.5 2 LM50 93/8 161/4 57/8 293/4 121 24
THREE 2 50DVFU62.2 2.2 3 LM50 93/8 151/8 57/8 3013/16 150 24
Dimensions: mm
SIZE OUTPUT Q.D.C. PUMP & MOTOR WEIGHT kg
PHASE ø MODEL
kW HP MODEL F G Q T PUMP Q.D.C.
50DVFU61.5 1.5 2 LM50 238 413 150 756 55 11
THREE 50 50DVFU62.2 2.2 3 LM50 238 384 150 782 68 11
29/16 (65)
G
13/8 (35)
279/16 (700)
F
29/16 (65)
Guide pipe support
Floor Frame
Manhole dimensions in
51/2 (140) Bolt 2–1/2 x 13/16 floor frame installation
39/16 (90)
19/16 (40)
23/16 (56)
23/4 (70)
1!5/16 (50)
23/4 (70)
SGP (W) 1"
Guide pipe length
m 43/4 (120) Q
T
.D. L . W. L.
e
P.C
ø
97/16 (240)
511/16 (145)
71/2 (190)
ø21
t
r
/2 (
65)
(n) QTY - (h) HOLES
11/4 (31)
33/4 (95)
Bolt 2 – 5/8 (16) Flange (ANSI 125 PSI F.F)
6 (152) 87/16 (215) inch
ø e f t n h r m
315/16 (100) 2 43/4 6 5
/8 4 3
/4 913/16 65/16
3 6 71/2 3
/4 4 3
/4 10 611/16
mm
ø e f t n h r m
50 121 152 16 4 19 250 161
Dimensions: inch 80 152 191 19 4 19 254 170
29/16 (65)
G
13/8 (35)
279/16 (700)
F
29/16 (65)
Guide pipe support Floor Frame
Manhole dimensions in
51/2 (140) Bolt 2–1/2 x 13/16 floor frame installation
19/16 (40)
39/16 (90)
23/16 (56)
115/16 (50)
23/4 (70)
23/4 (70)
SGP (W) 1"
Guide pipe length
m 415/16 (125) Q
ø3
r
t
(80
67/8 (175)
)
(n) QTY - (h) HOLES
11/4 (31)
Bolt 2 – 5/8 (16) 39/16 (90) Flange (ANSI 125 PSI F.F)
65/8 (168) 87/16 (215) inch
ø e f t n h r m
3 6 71/2 3
/4 4 3
/4 113/16 67/16
4 71/2 9 15
/16 8 3
/4 1113/16 75/8
315/16 (100) mm
ø e f t n h r m
80 152 191 19 4 19 284 164
Dimensions: inch 100 191 229 24 8 19 300 194
OUTPUT Q.D.C. PUMP & MOTOR WEIGHT Lb
PHASE SIZE
ø MODEL
MODEL
kW HP F G L Q T PUMP Q.D.C.
80DVBFU62.2 2.2 3 LM80 915/16 181/8 117/16 67/8 331/2 176 37
THREE 3/4 80DVBFU63.7 3.7 5 LM80 915/16 181/8 117/16 67/8 351/16 176 37
80DVFU65.5 5.5 71/2 LM80 111/4 1913/16 143/16 77/8 4115/16 262 37
Dimensions: mm
OUTPUT Q.D.C. PUMP & MOTOR WEIGHT kg
PHASE SIZE
ø MODEL
MODEL
kW HP F G L Q T PUMP Q.D.C.
80DVBFU62.2 2.2 3 LM80 252 460 290 175 851 80 17
THREE 80/100 80DVBFU63.7 3.7 5 LM80 252 460 290 175 891 80 17
80DVFU65.5 5.5 71/2 LM80 285 503 360 200 1065 119 17
*Note: All dimensions are based on 3'' discharge.
EBARA International Corporation
2-240
rev. 01/02
EBARA Submersible Vortex Sewage Pumps DVFU
Dimensions
Project: Model: Chk’d: Date:
Model DVFU with Quick Discharge Connector
80DVFU, 10HP 2 / (65) 31 / (800) 9
16
1
2 29/16 (65)
80DVBFU, 15HP
29/16 (65)
80DVCFU, 15 to 30HP
G
23/16 (55)
279/16 (700)
F
29/16 (65)
Guide pipe support
m 75/16 (185) Q
f
P.C
(120)
.D.
L . W. L. ø
155
)
t
10 /16 (255)
ø3
(80
97/16 (240)
71/16 (180) Bolt 4 – 5/8 (16) 61/2 (165) 23/16 (55) inch
6 /8 (168)
5
12 (305) ø e f t n h r m
3 6 71/2 3
/4 4 3
/4 133/4 711/16
4 71/2 9 15
/16 8 3
/4 143/8 87/8
mm
ø e f t n h r m
80 152 191 19 4 19 350 195
Dimensions: inch 100 191 229 24 8 19 365 226
OUTPUT Q.D.C. PUMP & MOTOR WEIGHT Lb
PHASE SIZE
ø MODEL
MODEL
kW HP F G L Q T PUMP Q.D.C.
80DVFU67.5 7.5 10 LL80 111/4 255/8 1615/16 77/8 4215/16 291 97
80DVBFU611 11 15 LL80 111/4 255/8 1615/16 77/8 469/16 390 97
80DVCFU611 11 15 LL80 137/16 255/8 1615/16 97/16 469/16 406 97
THREE 3/4
80DVCFU615 15 20 LL80 137/16 255/8 1711/16 97/16 491/8 503 97
80DVCFU618 18.5 25 LL80 137/16 255/8 1711/16 97/16 5011/16 578 97
80DVCFU622 22 30 LL80 137/16 255/8 1711/16 97/16 5011/16 633 97
Dimensions: mm
OUTPUT Q.D.C. PUMP & MOTOR WEIGHT kg
PHASE SIZE
ø MODEL
MODEL
kW HP F G L Q T PUMP Q.D.C.
80DVFU67.5 7.5 10 LL80 285 651 430 200 1090 132 44
80DVBFU611 11 15 LL80 285 651 430 200 1183 177 44
80DVCFU611 11 15 LL80 342 651 430 240 1183 184 44
THREE 80/100
80DVCFU615 15 20 LL80 342 651 450 240 1248 228 44
80DVCFU618 18.5 25 LL80 342 651 450 240 1288 262 44
80DVCFU622 22 30 LL80 342 651 450 240 1288 287 44
*Note: All dimensions are based on 3'' discharge.
EBARA International Corporation
2-241
rev. 01/02
EBARA Submersible Vortex Sewage Pumps DVFU
Dimensions
Project: Model: Chk’d: Date:
Model DVFU with Quick Discharge Connector
100DVFU, 5 to 10HP
100DVBFU, 15HP
100DVCFU, 15 to 20HP
29/16 (65) 311/2 (800) 29/16 (65)
29/16 (65)
G
23/16 (55)
279/16 (700)
F
29/16 (65)
Guide pipe support
Bolt 2–5/8 x 13/16 Floor Frame
911/16 (246) Manhole dimensions in
5 7/8 (150) (16x30) floor frame installation
Submersible Cable
315/16 (100)
23/4 (70)
t
P.C
(105) (105)
.D.
L . W. L.
(17
inch
143/8 (365)
ø4
10 /16 (265)
(10 ø e f t n h
97/16 (240)
0) 3 6 71/2 3
/4 4 3
/4
4 71/2 9 15
/16 8 3
/4
7
mm
23/8 (60)
Dimensions: mm
OUTPUT Q.D.C. PUMP & MOTOR WEIGHT kg
PHASE SIZE
ø MODEL
MODEL
kW HP F G L Q T PUMP Q.D.C.
100DVFU63.7 3.7 5 LL100 308 609 375 215 976 95 46
100DVFU65.5 5.5 71/2 LL100 308 609 448 215 1111 144 46
100DVFU67.5 7.5 10 LL100 308 609 448 215 1111 157 46
THREE 80/100
100DVBFU611 11 15 LL100 308 609 448 215 1204 205 46
100DVCFU611 11 15 LL100 308 609 448 215 1204 205 46
100DVCFU615 15 20 LL100 308 609 448 215 1269 248 46
29/16 (65)
G
23/16 (55)
279/16 (700)
F
29/16 (65)
Guide pipe support
Bolt 2–5/8 x 13/16 Floor Frame
911/16 (246) Manhole dimensions in
5 7/8 (150) (16x30) floor frame installation
Submersible Cable
315/16 (100)
23/4 (70)
(105) (105) ø
.D.
L . W. L.
t
(17
4 1515/16/16
(125)
5)
ø4
107/16 (265)
0)
inch
ø e f t n h
23/8 (60)
71/16 (180) Bolt 4 – 5/8 (16) 61/2 (165) 23/16 (55) 3 6 71/2 3
/4 4 3
/4
81/4 (210) 117/16 (290) 4 71/2 9 15
/16 8 3
/4
mm
ø e f t n h
80 152 191 19 4 19
100 191 229 24 8 19
Dimensions: inch
OUTPUT Q.D.C. PUMP & MOTOR WEIGHT Lb
PHASE SIZE
ø MODEL
MODEL
kW HP F G L Q T PUMP Q.D.C.
100DVDFU611 11 15 LL100 137/8 261/4 179/16 913/16 475/16 445 101
100DVDFU615 15 20 LL100 137/8 261/4 185/16 913/16 497/8 547 101
THREE 3/4
100DVDFU618 18.5 25 LL100 137/8 261/4 185/16 913/16 517/16 602 101
100DVDFU622 22 30 LL100 137/8 261/4 185/16 913/16 517/16 668 101
Dimensions: mm
OUTPUT Q.D.C. PUMP & MOTOR WEIGHT kg
PHASE SIZE
ø MODEL
MODEL
kW HP F G L Q T PUMP Q.D.C.
100DVDFU611 11 15 LL100 352 666 446 250 1202 202 46
15 20
THREE 80/100 100DVDFU615 LL100 352 666 465 250 1267 248 46
100DVDFU618 18.5 25 LL100 352 666 465 250 1307 273 46
100DVDFU622 22 30 LL100 352 666 465 250 1307 303 46
29/16 (65)
G
113/16 (46)
279/16 (700)
F
29/16 (65)
Guide pipe support
Floor Frame
109/16 (268) Bolt 2–5/8 x 13/16
Manhole dimensions in
57/8 (150)
(16x30) floor frame installation
Submersible Cable
315/16 (100)
23/4 (70)
e
.D.
L . W. L.
(21
0)
t
ø5 (n) QTY - (h) HOLES
141/4 (362)
117/16 (290)
(12
L
5)
r
Dimensions: mm
OUTPUT Q.D.C. PUMP & MOTOR WEIGHT kg
PHASE SIZE
ø MODEL
MODEL
kW HP F G L Q T PUMP Q.D.C.
150DVBFU611 11 15 LL125 332 602 547 235 1283 233 65
150DVBFU615 15 20 LL125 332 602 547 235 1348 276 65
150DVBFU618 18.5 25 LL125 332 602 547 235 1387 310 65
THREE 100/150
150DVBFU622 22 30 LL125 332 602 547 235 1387 335 65
150DVCFU618 18.5 25 LL125 384 663 544 270 1384 321 65
150DVCFU622 22 30 LL125 384 663 544 270 1384 346 65
115
3 830
849
2
801
876
802
814 849
1
909 120
4
193 115
2 2
111 120
3
193
1
120 816
1
120
2
115
1
174 005
039
117
021 001
080
125
PART ASTM, AISI NO. FOR PART ASTM, AISI NO. FOR
NO. PART NAME MATERIAL CODE 1 UNIT NO. PART NAME MATERIAL CODE 1 UNIT
001 CASING CAST IRON A48 Class 30 1 174 DISCHARGE ELBOW CAST IRON A48 Class 30 1
005 INTERMEDIATE CASING CAST IRON A48 Class 30 1 193-1 PLUG 304 STAINLESS AISI304 1
†021 IMPELLER CAST IRON A48 Class 30 1 193-2 PLUG 304 STAINLESS AISI304 1
039 KEY 420 STAINLESS AISI420 1 200 LIFTING HANGER STEEL A283 Grade D 1
080 BUSHING STEEL A283 Grade D 1 801 ROTOR — 1
†111 MECHANICAL SEAL — 1 SET 802 STATOR — 1
†115-1 O-RING RUBBER (NBR) 1 811-1 POWER CABLE — 1
†115-2 O-RING RUBBER (NBR) 1 811-2 CONTROL CABLE — 1
†115-3 O-RING RUBBER (NBR) 1 814 MOTOR COVER CAST IRON A48 Class 30 1
†115-4 O-RING RUBBER (NBR) 2 816 BRACKET CAST IRON A48 Class 30 1
†117 GASKET 1 817 BRACKET CAST IRON A48 Class 30 1
120-1 BOLT 304 STAINLESS AISI304 4 830 SHAFT 403 STAINLESS AISI403 1
120-2 BOLT 304 STAINLESS AISI304 4 838 WASHER 304 STAINLESS AISI304 2
120-3 BOLT 304 STAINLESS AISI304 4 †849-1 BALL BEARING — 1
120-4 BOLT 304 STAINLESS AISI304 3 †849-2 BALL BEARING — 1
120-5 BOLT 304 STAINLESS AISI304 4 876 MOTOR PROTECTOR — 3
120-6 BOLT 304 STAINLESS AISI304 2 909 LEAKAGE DETECTOR — 1
125 BOLT 304 STAINLESS AISI304 1 924 PACKING RUBBER (NBR) 2
115 115
4 5
849 817
2
876 120
5
115
814 3
830 801
849 802
1
120
909 4
115 120
2 3
193 816
2
193 120
1 2
111 005
115 114
1
039
001
080
021
174
125
120
1
117
PART ASTM, AISI NO. FOR PART ASTM, AISI NO. FOR
NO. PART NAME MATERIAL CODE 1 UNIT NO. PART NAME MATERIAL CODE 1 UNIT
001 CASING CAST IRON A48 Class 30 1 174 DISCHARGE ELBOW CAST IRON A48 Class 30 1
005 INTERMEDIATE CASING CAST IRON A48 Class 30 1 193-1 PLUG 304 STAINLESS AISI304 1
021 IMPELLER CAST IRON A48 Class 30 1 193-2 PLUG 304 STAINLESS AISI304 1
039 KEY 420 STAINLESS AISI420 1 200 LIFTING HANGER STEEL A283 Grade D 1
080 BUSHING STEEL A283 Grade D 1 801 ROTOR — 1
†111 MECHANICAL SEAL — 1 SET 802 STATOR — 1
†114 OIL SEAL RUBBER (NBR) 1 811-1 POWER CABLE — 1
†115-1 O-RING RUBBER (NBR) 1 811-2 CONTROL CABLE — 1
†115-2 O-RING RUBBER (NBR) 1 814 MOTOR COVER CAST IRON A48 Class 30 1
†115-3 O-RING RUBBER (NBR) 1 816 BRACKET CAST IRON A48 Class 30 1
†115-4 O-RING RUBBER (NBR) 1 817 BRACKET CAST IRON A48 Class 30 1
†115-5 O-RING RUBBER (NBR) 1 830 SHAFT 420J2 STAINLESS AISI420 1
†117 GASKET 1 838-1 WASHER 304 STAINLESS AISI304 1
120-1 BOLT 304 STAINLESS AISI304 8 838-2 WASHER 304 STAINLESS AISI304 1
120-2 BOLT 304 STAINLESS AISI304 4 †849-1 BALL BEARING — 1
120-3 BOLT 304 STAINLESS AISI304 6 †849-2 BALL BEARING — 1
120-4 BOLT 304 STAINLESS AISI304 3 876 MOTOR PROTECTOR — 3
120-5 BOLT 304 STAINLESS AISI304 4 909 LEAKAGE DETECTOR — 1
120-6 BOLT 304 STAINLESS AISI304 2 924-1 PACKING RUBBER (NBR) 1
125 BOLT 304 STAINLESS AISI304 1 924-2 PACKING RUBBER (NBR) 1
120
5
909 115
3
120 120
3 4
193 816
2 2
111 816
1
115
114 2
193
120 1
1
120
2
115
1
174
005
117
039
021
001
125
080
PART ASTM, AISI NO. FOR PART ASTM, AISI NO. FOR
NO. PART NAME MATERIAL CODE 1 UNIT NO. PART NAME MATERIAL CODE 1 UNIT
001 CASING CAST IRON A48 Class 30 1 174 DISCHARGE ELBOW CAST IRON A48 Class 30 1
005 INTERMEDIATE CASING CAST IRON A48 Class 30 1 193-1 PLUG 304 STAINLESS AISI304 1
021 IMPELLER CAST IRON A48 Class 30 1 193-2 PLUG 304 STAINLESS AISI304 1
039 KEY 420 STAINLESS AISI420 1 200 LIFTING HANGER STEEL A283 Grade D 1
080 BUSHING STEEL A283 Grade D 1 801 ROTOR — 1
†111 MECHANICAL SEAL — 1 SET 802 STATOR — 1
†114 OIL SEAL RUBBER (NBR) 1 811-1 POWER CABLE — 1
†115-1 O-RING RUBBER (NBR) 1 811-2 CONTROL CABLE — 1
†115-2 O-RING RUBBER (NBR) 1 814 MOTOR FRAME CAST IRON A48 Class 30 1
†115-3 O-RING RUBBER (NBR) 1 816-1 BRACKET CAST IRON A48 Class 30 1
†115-4 O-RING RUBBER (NBR) 1 816-2 BRACKET CAST IRON A48 Class 30 1
†115-5 O-RING RUBBER (NBR) 1 817 BRACKET CAST IRON A48 Class 30 1
†115-6 O-RING RUBBER (NBR) 1 830 SHAFT 420J2 STAINLESS AISI420 1
†117 GASKET 1 838-1 WASHER 304 STAINLESS AISI304 1
120-1 BOLT 304 STAINLESS AISI304 8 838-2 WASHER 304 STAINLESS AISI304 1
120-2 BOLT 304 STAINLESS AISI304 4 †849-1 BALL BEARING — 1
120-3 BOLT 304 STAINLESS AISI304 6 †849-2 BALL BEARING — 1
120-4 BOLT 304 STAINLESS AISI304 6 876 MOTOR PROTECTOR — 3
120-5 BOLT 304 STAINLESS AISI304 3 909 LEAKAGE DETECTOR — 1
120-6 BOLT 304 STAINLESS AISI304 6 924-1 PACKING RUBBER (NBR) 1
120-7 BOLT 304 STAINLESS AISI304 2 924-2 PACKING RUBBER (NBR) 1
125 BOLT 304 STAINLESS AISI304 1
Motors are purchased as a complete unit
†: Recommended spare parts