Documente Academic
Documente Profesional
Documente Cultură
Solid-state Timers
H3DK
DIN Track-mounted, 22.5-mm-width LR
Standard Timer Series
• A wide AC/DC power supply range (24 to 240 VAC/DC).*1
• All sub-series include models with 12-VDC power supply.*1
• G-type Models (H3DK-G) now include model with 240 to 440-
VAC power supply.
• UL*2, CSA, and CCC certification and EN 61812-1 compliance.
CE Marking.
• EMC (EN 61812-1) compliance for application in heavy industri-
al, residential, commercial, or light industrial environments.
• Finger-safe terminal block and captive screws according to EN
50274.
*1. Except for the H3DK-H.
*2. Except for the H3DK-GE.
■ Model Number Legend (Not all models that can be represented with the model number legend can necessarily be produced.)
H3DK-@@@@
1 2 3 4
1. Type 2. Control Output 3. Supply Voltage 4. Time Ranges (H-type
Symbol Meaning Symbol Meaning Symbol Meaning Models Only)
M Eight-mode Timer 1 SPDT Blank 24 to 240 VAC/DC Symbol Meaning
S Four-mode Timer 2 DPDT A 12 VDC S 0.1 to 1.2 s or 1 to 12 s
F Twin Timer * M- and S-type models only. B 24 to 48 VAC/DC L 1 to 12 s or 10 to 120 s
G Star-delta Timer C 100 to 120 VAC
H Power OFF-delay Timer D 200 to 240 VAC
E 240 to 440 VAC *
* G-type models only.
1
New Product News
Ordering Information
■ List of Models
Supply voltage Control output Eight-mode Timer Four-mode Timer
Contact output, DPDT (time-limit DPDT, or time-limit
SPDT + instantaneous SPDT) Model H3DK-M2 H3DK-S2
24 to 240 VAC/DC Changed using a switch.
Contact output, SPDT (time-limit SPDT) Model H3DK-M1 H3DK-S1
Contact output, DPDT (time-limit DPDT, or time-limit
SPDT + instantaneous SPDT) Model H3DK-M2A H3DK-S2A
12 VDC Changed using a switch.
Contact output, SPDT (time-limit SPDT) Model H3DK-M1A H3DK-S1A
■ Model Structure
Model Operating modes Terminal block Input type Output type Mounting method Safety standards Accessories
A: ON Delay
H3DK-M2 B: Flicker OFF start Relay, DPDT
B2: Flicker ON start
C: Signal ON/OFF Delay
Voltage input cURus (UL 508
D: Signal OFF Delay
E: Interval 9 terminals CSA C22.2 No. 14)
H3DK-M1 G: Signal ON/OFF Delay Relay, SPDT DIN Track mounting EN 61812-1 User label
J: One-shot Output IEC 60664-1 4 kV/2
EN 50274
H3DK-S2 A: ON Delay Relay, DPDT
B2: Flicker ON start
---
E: Interval
H3DK-S1 J: One-shot Output 6 terminals Relay, SPDT
2
H3DK-M/H3DK-S
Specifications
■ Time Ranges
Time range setting 0.1 s 1s 10 s 1 min 10 min 1h 10 h 100 h
Set time range 0.1 to 1.2 s 1 to 12 s 10 to 120 s 1 to 12 min 10 to 120 min 1 to 12 h 10 to 120 h 100 to 1,200 h
Scale numbers 12
■ Ratings
• 24 to 240 VAC/DC, 50/60 Hz *2 *1. When using a 24-VDC power supply voltage, there will
Power supply voltage *1 be an inrush current of approximately 0.25 A. Allow for
• 12 VDC *2
this inrush current when turning ON and OFF the
Allowable voltage fluctuation • 24 to 240 VAC/DC: 85% to 110% of rated voltage
power supply to the Timer with device with a solid-
range • 12 VDC: 90% to 110% of rated voltage
state output, such as a sensor.
Power reset Minimum power-OFF time: 0.1 s *2. DC ripple: 20% max.
Reset voltage 10% of rated voltage *3. The power consumption is for mode A after the Timer
• 24 to 240 VAC/DC times out.
High level: 20.4 to 264 VAC/DC, Low level: 0 to 2.4 VAC/DC For the H3DK-M@, the maximum power consumption
Voltage input is given, including the current consumed by the input
• 12 VDC
High level: 10.8 to 13.2 VDC, Low level: 0 to 1.2 VDC circuit.
*4. Refer to DC Power Consumptions (Reference Infor-
H3DK-M2/-S2 At 240 VAC: 6.6 VA max. *4 mation) on page 27 for DC power consumptions.
*3 H3DK-M1/-S1 At 240 VAC: 4.5 VA max. *4 *5. The control output ratings are for one H3DK operating
Power con-
H3DK-M2A/-S2A At 12 VDC: 0.9 W max. alone. If you operate two or more Timers side by side,
sumption
refer to Installation Pitch and Output Switching Capac-
H3DK-M1A/-S1A At 12 VDC: 0.6 W max.
ity (Reference Values) on the next page.
Contact output, 5 A at 250 VAC with resistive load (cosφ = 1), *6. 125 VDC: 0.15 A max. with resistive load, 125 VDC:
Control output
5 A at 30 VDC with resistive load *4, *5 0.1 A with L/R of 7 ms.
Ambient operating temperature −20 to 55°C (with no icing) Minimum load: 10 mA at 5 VDC (P level, reference
Storage temperature −40 to 70°C (with no icing) value)
Ambient operating humidity 25% to 85%
3
H3DK-M/H3DK-S
■ Characteristics
Accuracy of operating ● Installation Pitch and Output
±1% of FS max. (±1% ±10 ms max. at 1.2-s range)*
time Switching Capacity (Reference Val-
Setting error ±10% of FS ±0.05 s max.* ues)
Minimum input signal
50 ms* (start input) The relation between the installation pitch
width
and the load current is shown in the follow-
Influence of voltage ±0.5% of FS max. (±0.5% ±10 ms max. at 1.2-s range)
ing graph. (Except for the H3DK-GE)
Influence of tempera-
±2% of FS max. (±2% ±10 ms max. at 1.2-s range)
ture If Timer is used under load conditions that
Insulation resistance 100 MΩ min. at 500 VDC exceed the specified values, the tempera-
Between current-carrying metal parts and exposed non-current-carrying metal ture inside the Timer will increase, reducing
parts: 2,000 VAC 50/60 Hz for 1 min. the life expectancy of internal parts.
Between control output terminals and operating circuit: 2,000 VAC 50/60 Hz for
Dielectric strength
1 min. 80
temperature in specifications
Maximum ambient operating
30
Static immunity Malfunction: 4 kV, Destruction: 8 kV
d=0 A
Vibration Destruction 0.75-mm single amplitude at 10 to 55 Hz for 2 h each in 3 directions 20
resistance Malfunction 0.5-mm single amplitude at 10 to 55 Hz for 10 min each in 3 directions
10
Shock re- Destruction 1,000 m/s2 3 times each in 6 directions
sistance Malfunction 100 m/s2 3 times each in 6 directions 0 1 2 3 4 5 6
Load current (A)
Life ex- Mechanical 10 million operations min. (under no load at 1,800 operations/h)
pectancy Electrical 100,000 operations min. (5 A at 250 VAC, resistive load at 360 operations/h) Testing Method
Tested Timer: H3DK-M/-S
Degree of protection IP30 (Terminal block: IP20) Applied voltage: 240 VAC
Weight Approx. 120 g Installation pitch: 0, 5, 10, and 50 mm
* With the H3DK-M@, if the voltage exceeds 26.4 VAC/DC in mode C, D, or G, the OFF trigger signal char-
Test Test Test Test Test
acteristics are as follows: timer timer timer timer timer
1 2 3 4 5
Accuracy of operating time: ±1% ±50 ms max.
+100 ms
Setting error: ±10% −50 ms max.
Minimum input signal width: 100 ms DIN Track Timer installation pitch: d
■ Applicable standards
cURus: UL 508/CSA C22.2 No. 14
EN 50274: Finger protection, back-of-hand proof
Safety standards EN 61812-1: Pollution degree 2, Overvoltage category III
CCC: Pollution degree 2, Overvoltage category II, section DB14048.5-2008 part 5-1
LR: Test Specification No. 1-2002 Category ENV 1.2
(EMI) EN61812-1
Radiated Emissions: EN 55011 class B
Emission AC Mains: EN 55011 class B
Harmonic Current: EN 61000-3-2
Voltage Fluctuations and Flicker:
EN61000-3-3
(EMS) EN61812-1
ESD Immunity: EN 61000-4-2: 6 kV contact discharge,
EMC
8 kV air discharge
Radiated Radio-Frequency Electromagnetic Field Immunity (AM Radio Waves):
EN 61000-4-3: 10 V/m (80 MHz to 1 GHz)
Burst Immunity: EN 61000-4-4: 2 kV power line,
1 kV I/O signal line
Surge Immunity: EN 61000-4-5: 2 kV common mode,
1 kV differential mode
■ I/O
Item Model H3DK-M1/-M2 H3DK-S1/-S2
Input Start Functions to start timing. There is no start input.
Control The output is turned ON/OFF according to the operating mode when the value
Output output that is set on the dial is reached. *
* If the INST/TIME switch on the front of the Timer is set to INST on the H3DK-M2/-S2, relay R2 will
operate as instantaneous contacts and will turn ON/OFF in synchronization with the power supply.
4
H3DK-M/H3DK-S
Connections
■Block Diagrams
H3DK-M1/-M2
One-chip microcomputer
Power Output
indicator indicator
H3DK-S1/-S2
One-chip microcomputer
Indicator circuit
Power Output
indicator indicator
5
H3DK-M/H3DK-S
■ Terminal Arrangement
H3DK-M1 H3DK-M2 H3DK-S1 H3DK-S2
A1 15 A1 15 25/21 A1 15 A1 15 25/21
* *
R1 R1 R2 R1 R1 R2
15 15 25/21 15 15 25/21
18 16 A2 18 16 A2 18 16 A2 18 16 A2
■ Input Connections
The start input of the H3DK-M1/-M2 is a voltage input.
PNP Transistor Input NPN Transistor Input Relay Input Voltage Input Signal Levels
Sensor
24 VDC
1. Transistor ON
24 VDC
Sensor (sensor Timer (sensor Timer Timer • Residual voltage: 1 V max.
power supply) power supply) Voltage between terminals B1
A1 (+) A1 (−) A1
and A2 must be equal to or
(+) (−)
higher than the rated high level
24 24 Tran- voltage (20.4 VDC min.).
VDC (−) B1 VDC (+) B1 B1 sistor
Start Start Start 2. Transistor OFF
input
A2 (−) A2 (+) A2 • Leakage current: 0.01 mA max.
Voltage between terminals B1
Operates when PNP transistor turns ON. Operates when NPN transistor turns ON. Operates when relay turns ON.
and A2 must be equal to or
below the rated low level voltage
Consider the minimum load
(2.4 VDC min.).
of the relay. (See signal
levels on the right.) Use relays that can adequately
switch 0.1 mA at the imposed
voltage.
When the relay is ON or OFF, the
voltage between terminals B1 and
A2 must be within the following
Relay ranges:
input • 24 to 240 VAC/DC
When relay is ON: 20.4 to 264
VAC/DC
When relay is OFF: 0 to 2.4 V
• 12 VDC
When relay is ON: 10.8 to 13.2 V
When relay is OFF: 0 to 1.2 V
6
H3DK-M/H3DK-S
Nomenclature
H3DK-M2
Front View Bottom View
H3DK-S2
Output indicator (orange) Main dial Output indicator (orange) Main dial
(Lit while Timer gives output.) (for setting the time) (Lit while Timer gives output.) (for setting the time)
*If the switch is left between settings, proper operation may not be possible. *If the switch is left between settings, proper operation may not be possible.
Make sure that the switch is set properly. Make sure that the switch is set properly.
Note: The default settings are for 0.1 s in mode A. Note: The default settings are for 0.1 s in mode A.
7
H3DK-M/H3DK-S
Dimensions (Unit: mm)
■ Timers
H3DK-M
H3DK-S
100
88.2
22.5 22.5 22.5 69.1
4
79 65.6 52 89.4
H3DK-M2 H3DK-M1
H3DK-S2 H3DK-S1
Operating Procedures
■ Basic Operation
● Setting Switches
• Each switch has a snap mechanism that secures the switch at given positions. Set the switch to one of these positions.
Do not set it midway between two positions. Malfunction could result from an improper setting.
Setting the Operating Mode Setting the INIT/TIME Switch Setting the Time Range
● Setting the Operating Mode ● Switching Relay R2 between ● Setting the Time Range
The H3DK-M can be set to any of eight Instantaneous and Time-limit The time range switch can be used to set
operating modes. The H3DK-S can be Contacts (H3DK-M2/-S2 Only) the time range. Turn the switch with a
set to any of four operating modes. Turn The INIT/TIME switch can be used to flat-blade or Phillips screwdriver.
the operating mode switch with a flat- switch relay R2 between instantaneous
blade or Phillips screwdriver. The H3DK- and time-limit operation.
M can be set to any of eight modes; the
H3DK-S, to any of four modes.
Time range
switch
INIT/TIME
switch
Operating
mode switch
8
H3DK-M/H3DK-S
■ Timing Charts
• There is no start input with the H3DK-S. Timer operation starts when the power is turned ON.
• There is no instantaneous output with the H3DK-@1.
A: ON Delay
t
t−a
t
Basic Operation
Time-limit contacts: NC * **
15 and 16 (25 and 26) Start input
Time-limit contacts: NO Timing Timing Timing Timing
(output indicator) Output
15 and 18 (25 and 28)
Instantaneous contacts: NC * To start with the power supply, connect start input
(21 and 22) terminals B1 and A1. The Timer starts operating
as soon as the power turns ON.
Instantaneous contacts: NO ** The start input is ignored while the Timer is in
(21 and 24) operation.
Power indicator
t t t
t−a
t
t−a Basic Operation
Note 1.The reset time is 0.1 s min. Make sure the signal input time is 0.05 s or longer.
Note 2.“t” is the set time. “t−a” is a time that is less that the set time.
9
H3DK-M/H3DK-S
E: Interval
Instantaneous contacts: NC
* The start input is valid while the Timer is in
(21 and 22)
operation.
Instantaneous contacts: NO
(21 and 24)
Power indicator
Note 1.The reset time is 0.1 s min. Make sure the signal input time is 0.05 s or longer.
Note 2.“t” is the set time. “t−a” is a time that is less that the set time.
10
New Product News
Twin Timer
H3DK-F
• Switch between flicker-OFF or flicker-ON start mode. LR
• Independent ON time and OFF time settings.
• Eight time ranges from 0.1 s to 1,200 h.
Ordering Information
■ List of Models
Operating
modes Supply voltage Control output H3DK-F
Contact out-
Flicker OFF 24 to 240 VAC/DC Model H3DK-F
put: SPDT
start/flicker ON
start Contact out-
12 VDC Model H3DK-FA
put: SPDT
■ Model Structure
Model Operating modes Terminal block Output type Mounting method Safety standards Accessories
cURus
(UL508
Flicker OFF start/flicker ON CSA C22.2 No. 14)
H3DK-F 6 terminals Relay, SPDT DIN Track mounting User label
start EN 61812-1
IEC 60664-1 4 kV/2
EN 50274
Specifications
■ Time Ranges
Time range setting 0.1 s 1s 10 s 1 min 10 min 1h 10 h 100 h
Set time range 0.1 to 1.2 s 1 to 12 s 10 to 120 s 1 to 12 min 10 to 120 min 1 to 12 h 10 to 120 h 100 to 1,200 h
Scale numbers 12
■ Ratings
• 24 to 240 VAC/DC, 50/60 Hz *2
Power supply voltage *1
• 12 VDC *2
• 24 to 240 VAC/DC: 85% to 110% of rated voltage
Allowable voltage fluctuation range
• 12 VDC: 90% to 110% of rated voltage
Power reset Minimum power-OFF time: 0.1 s
Reset voltage 10% of rated voltage
H3DK-F At 240 VAC: 4.5VA max. *3
Power consumption
H3DK-FA At 12 VDC: 0.6 W max.
Contact output (SPDT): 5 A at 250 VAC with resistive load (cosφ = 1)
Control output
5 A at 24 VDC with resistive load *3, *4
Ambient operating temperature −20 to 55°C (with no icing)
Storage temperature −40 to 70°C (with no icing)
Ambient operating humidity 25% to 85%
11
H3DK-F
*1. When using a 24-VDC power supply voltage, there will be an inrush current of approximately 0.25 A. Allow for this inrush current when turning ON and OFF the
power supply to the Timer with device with a solid-state output, such as a sensor.
*2. DC ripple: 20% max.
*3. Refer to DC Power Consumptions (Reference Information) on page 27 for DC power consumptions.
*4. The control output ratings are for one H3DK operating alone. If you operate two or more Timers side by side, refer to Installation Pitch and Output Switching Capacity
(Reference Values) on the next page.
*5. 125 VDC: 0.15 A max. with resistive load, 125 VDC: 0.1 A with L/R of 7 ms.
Minimum load: 10 mA at 5 VDC (P level, reference value)
■ Characteristics
Accuracy of operating ● Installation Pitch and Output
±1% of FS max. (±1% ±10 ms max. at 1.2-s range)
time Switching Capacity (Reference
Setting error ±10% of FS ±0.05 s max. Values)
Influence of voltage ±0.5% of FS max. (±0.5% ±10 ms max. at 1.2-s range)
The relation between the installation pitch
Influence of tempera-
±2% of FS max. (±2% ±10 ms max. at 1.2-s range) and the load current is shown in the follow-
ture
ing graph. (Except for the H3DK-GE)
Insulation resistance 100 MΩ min. at 500 VDC
If Timer is used under load conditions that
Between current-carrying metal parts and exposed non-current-carrying metal
parts: 2,000 VAC 50/60 Hz for 1 min. exceed the specified values, the tempera-
Between control output terminals and operating circuit: 2,000 VAC 50/60 Hz for ture inside the Timer will increase, reduc-
Dielectric strength
1 min.
Between contacts not located next to each other: 1,000 VAC 50/60 Hz for ing the life expectancy of internal parts.
1 min.
80
temperature in specifications
Maximum ambient operating
Vibration Destruction 0.75-mm single amplitude at 10 to 55 Hz for 2 h each in 3 directions
30
resistance Malfunction 0.5-mm single amplitude at 10 to 55 Hz for 10 min each in 3 directions d = 0 mm
20
Shock re- Destruction 1,000 m/s2 3 times each in 6 directions
sistance Malfunction 100 m/s2 3 times each in 6 directions 10
Life ex- Mechanical 10 million operations min. (under no load at 1,800 operations/h)
pectancy 0 1 2 3 4 5 6
Electrical 100,000 operations min. (5 A at 250 VAC, resistive load at 360 operations/h)
Load current (A)
Degree of protection IP30 (Terminal block: IP20)
Testing Method
Weight Approx. 110 g
Tested Timer: H3DK-F
Applied voltage: 240 VAC
■ Applicable standards Installation pitch: 0, 5, 10, and 50 mm
■ I/O
Input None
Output is turned ON/OFF according to the time set on the ON
Output Control output
time setting dial and OFF time setting dial.
12
H3DK-F
Connections
■ Block Diagrams ■ Terminal Arrangement
H3DK-F H3DK-F
A1 15
ON OFF
indicator indicator
ON/OFF time setting
ON/OFF start switch R1
detection circuit
15
Time
AC (DC) specification
input Indicator
circuit switches
18 16
ROM RAM Clock
One-chip microcomputer
Power supply
circuit Output circuit
18 16 A2
(DIN notation)
15
A1
A2
16 18
Note: The power supply terminals do not have po-
larity.
Nomenclature
H3DK-F
13
H3DK-F
Dimensions (Unit: mm)
■ Timers
H3DK-F
100
88.2
22.5 69.1
4
79 65.6 52 89.4
Operating Procedures
■ Basic Operation
Setting the Time Ranges Setting the ON/OFF Start Switch Setting the Times
● Setting the Time Ranges ● Setting an ON Start or OFF Start ● Setting the Times
Use the ON time range switch to set the The ON/OFF start switch can be used to Use the ON time setting dial and the
ON time range and the OFF time range switch between ON-start and OFF-start OFF time setting dial to set the ON time
switch to set the OFF time range. Turn operation. and OFF time.
the switches with a flat-blade or Phillips
screwdriver.
ON time range
switch
ON/OFF start
switch
■ Timing Charts
Flicker OFF start Flicker ON start
OFF indicator (15 and 16) ON OFF indicator (15 and 16) ON
OFF OFF
14
New Product News
Star-delta Timer
H3DK-G
• Set two time ranges between 1 and 120 s with one Timer. LR
• Models with 240 to 440-VAC power supply added to series.
Ordering Information
■ List of Models
Operating modes Supply voltage Control output H3DK-G
24 to 240 VAC/DC Model H3DK-G
Contact outputs
Star-delta Timer 12 VDC Model H3DK-GA
Delta circuit: SPDT, Star circuit: SPDT
240 to 440 VAC Model H3DK-GE
■ Model Structure
Model Terminal block Operating/resetting method Output type Mounting method Safety standards Accessories
cURus*1
(UL 508
Time-limit (relay)
Time-limit operation/self- CSA C22.2 No. 14)
H3DK-G 9 terminals Star circuit: SPDT DIN Track mounting User label
resetting EN 61812-1
Delta circuit: SPDT
IEC 60664-1 4 kV/2
EN 50274
*1. Except for the H3DK-GE.
Specifications
■ Time Ranges
Time range setting t1x1 t1x10
Star set time (t1) range 1 to 12 s 10 to 120 s
Star-Delta transfer time (t2) Select from 0.05, 0.1, 0.25, or 0.5 s.
■ Ratings
H3DK-G, -GA H3DK-GE
• 24 to 240 VAC/DC, 50/60 Hz *2
Power supply voltage *1 • 240 to 440 VAC (50/60 Hz) *6
• 12 VDC *2
• 24 to 240 VAC/DC: 85% to 110% of rated voltage
Allowable voltage fluctuation range 80 % to 110% of rated voltage
• 12 VDC: 90% to 110% of rated voltage
Power reset Minimum power-OFF time: 0.5 s
Reset voltage 10% of rated voltage
H3DK-G At 240 VAC: 6.6 VA max. *3
Power consumption At 440 VAC: 34 VA max.
H3DK-GA At 12 VDC: 0.9 W max.
Contact output (Time-limit output: relay, Star output: Ith 2 A
SPDT, Delta output: SPDT): AC-15 120 VAC: 1.5 A
Control output
5 A at 250 VAC with resistive load (cosφ = 1) AC-15 240 VAC: 1 A
5 A at 24 VDC with resistive load *3, *4 AC-15 440 VAC: 0.3 A
Ambient operating temperature −20 to 55°C (with no icing)
Storage temperature −40 to 70°C (with no icing)
Ambient operating humidity 25% to 85%
15
H3DK-G
*1. When using a 24-VDC power supply voltage, there will be an inrush current of approximately 0.25 A. Allow for this inrush current when turning ON and OFF the
power supply to the Timer with device with a solid-state output, such as a sensor.
*2. DC ripple: 20% max.
*3. Refer to DC Power Consumptions (Reference Information) on page 27 for DC power consumptions.
*4. The control output ratings are for one H3DK operating alone. If you operate two or more Timers side by side, refer to Installation Pitch and Output Switching Capacity
(Reference Values) on the next page.
*5. 125 VDC: 0.15 A max. with resistive load, 125 VDC: 0.1 A with L/R of 7 ms.
Minimum load: 10 mA at 5 VDC (P level, reference value)
*6. For the H3DK-GE, approx. 6 A of inrush current will flow when the power supply is turned ON. When selecting the device connected to the Timer, allow leeway in
the current ratings.
■ Characteristics
H3DK-G, -GA H3DK-GE ● Installation Pitch and Output
Accuracy of operating Switching Capacity (Reference
±1% of FS max.
time
Values)
Setting error ±10% of FS ±0.05 s max.
The relation between the installation pitch
Transfer time Total error ± (25% of transfer time + 5 ms) max.
and the load current is shown in the fol-
Influence of voltage ±0.5% of FS max.
lowing graph. (Except for the H3DK-GE)
Influence of tempera-
±2% of FS max. If Timer is used under load conditions that
ture
Insulation resistance 100 MΩ min. at 500 VDC exceed the specified values, the tempera-
Between current-carrying metal parts Between current-carrying metal parts ture inside the Timer will increase, reduc-
and exposed non-current-carrying metal and exposed non-current-carrying metal ing the life expectancy of internal parts.
parts: 2,000 VAC 50/60 Hz for 1 min. parts: 2,500 VAC 50/60 Hz for 1 min.
Between control output terminals and Between control output terminals and 80
temperature in specifications
parts and exposed non-current- Maximum ambient operating 30
Impulse withstand volt- carrying metal parts d = 0 mm
---
age H3DK-GA: 12 VDC: 1 kV between 20
power terminals, 1.5 kV between
current-carrying metal parts and 10
exposed non-current-carrying
metal parts
0 1 2 3 4 5 6
Square-wave noise generated by noise simulator (pulse width: 100 ns/1 µs, Load current (A)
Noise immunity
1-ns rise): ±1.5 kV*
Testing Method
Static immunity Malfunction: 4 kV, Destruction: 8 kV
Tested Timer: H3DK-G
Vibration Destruction 0.75-mm single amplitude at 10 to 55 Hz for 2 h each in 3 directions Applied voltage: 240 VAC
resistance Malfunction 0.5-mm single amplitude at 10 to 55 Hz for 10 min each in 3 directions Installation pitch: 0, 5, 10, and 50 mm
Shock re- Destruction 1,000 m/s2 3 times each in 6 directions Test Test Test Test Test
sistance timer timer timer timer timer
Malfunction 100 m/s2 3 times each in 6 directions 1 2 3 4 5
10 million operations min. (under no 10 million operations min.
Mechanical
load at 1,800 operations/h) (under no load at 1,800 operations/h)
Life ex- DIN Track Timer installation pitch: d
pectancy 100,000 operations min.
100,000 operations min. (5 A at 250
Electrical (0.3 A at 440 VAC, resistive load at
VAC, resistive load at 360 operations/h)
1,800 operations/h)
Degree of protection IP30 (Terminal block: IP20)
Weight Approx. 120 g
* Except for the H3DK-GE
16
H3DK-G
■ Applicable standards
cURus: UL 508/CSA C22.2 No. 14 *1
EN 50274: Finger protection, back-of-hand proof
Safety standards EN 61812-1: Pollution degree 2, Overvoltage category III *2
CCC: Pollution degree 2, Overvoltage category II, section DB14048.5-2008 part 5-1
LR: Test Specification No. 1-2002 Category ENV 1.2 *1
(EMI) EN61812-1
Radiated Emissions: EN 55011 class B
Emission AC Mains: EN 55011 class B
Harmonic Current: EN 61000-3-2 *1
EN61000-3-3 *1
Voltage Fluctuations and Flicker:
(EMS) EN61812-1
ESD Immunity: EN 61000-4-2: 6 kV contact discharge,
EMC
8 kV air discharge
Radiated Radio-Frequency Electromagnetic Field Immunity (AM Radio Waves):
EN 61000-4-3: 10 V/m (80 MHz to 1 GHz)
Burst Immunity: EN 61000-4-4: 2 kV power line,
1 kV I/O signal line
Surge Immunity: EN 61000-4-5: 2 kV common mode,
1 kV differential mode
*1. This standard is not applicable to the H3DK-GE.
*2. This standard is not applicable if the output is used with a rating that exceeds 250 VAC.
■ I/O
Input None
The star output is turned OFF when the dial set value is reached and the
Output Control output
delta output is turned ON after the preset transfer time elapses.
Connections
■ Block Diagrams ■ Terminal Arrangement
H3DK-G H3DK-G
28 26
Indicator circuit
18 16 A2
(DIN notation)
Star output ON Delta output ON
indicator indicator
15 25
A1
A2
16 18 26 28
17
H3DK-G
Nomenclature
H3DK-G Front View Bottom View
User label
attachment location
Terminal block
(See notes 1 and 2.)
Star operation Main dial
indicator (green) (Sets the star time.)
Delta operation
indicator (orange)
Front cover
Star-delta transfer time
(See note 3.)
switch
18
H3DK-G
Dimensions (Unit: mm)
■ Timers
H3DK-G
100
88.2
22.5 69.1
4
79 65.6 52 89.4
H3DK-GE
102
88.2
26 69.1
22.5 4
65.6
89.4
79
55
19
H3DK-G
Operating Procedures
■ Basic Operation
Setting the Time Ranges Setting the Time
● Setting the Delta Time Range and the Star-delta Transfer ● Setting the Time
Time (t2) The start time is set with the main dial.
Star Time (t1) Range
Set the star-delta transfer time.
For ×1 (1 to 12 s), use side (A) (labeled “t1×1”).
For ×10 (10 to 120 s), use side (B) (labeled “t10×1”).
(See following diagram.) Main dial
(A) (B)
0.5s 0.5s
0.25s 0.25s
0.1s 0.1s
0.05s
Star-delta transfer 0.05s
time setting (t2) t2 t2
Switches the start t1x1 t1x10
time (t1) range.
■ Timing Chart
0.5 s min.
ON
Power (A1 and A2)
OFF
t1
ON t2
Star contacts (15 and 18)
OFF
ON
Delta contacts (25 and 26)
OFF
ON
Star operation indicator
OFF
Note: “t1” is the start set time. “t2” is the transfer time.
20
New Product News
Ordering Information
■ List of Models
H3DK-H
S Series L Series
Operating modes Supply voltage Control output (time range: 0.1 to 12 s) (time range: 1.0 to 120 s)
100 to 120 VAC Contact output: SPDT Model H3DK-HCS H3DK-HCL
Power OFF Delay 200 to 240 VAC Contact output: SPDT Model H3DK-HDS H3DK-HDL
24 to 48 VAC/DC Contact output: SPDT Model H3DK-HBS H3DK-HBL
■ Model Structure
Model Terminal block Operating/resetting method Output type Mounting method Safety standards Accessories
cURus
(UL 508
Instantaneous operation/ CSA C22.2 No. 14)
H3DK-H 6 terminals Relay, SPDT DIN Track mounting User label
time-limit reset EN 61812-1
IEC 60664-1 4 kV/2
EN 50274
Specifications
■ Time Ranges
S Series L Series
Time range setting x0.1 x1 x1 x10
Set time range 0.1 to 1.2 s 1 to 12 s 1 to 12 s 10 to 120 s
Power ON time 0.1 s min. 0.3 s min.
Scale numbers 12
■ Ratings
• 100 to 120 VAC, 50/60 Hz
Supply voltage • 200 to 240 VAC, 50/60 Hz
• 24 to 48 VAC/DC, 50/60 Hz *1
Contact output, 5 A at 250 VAC with resistive load (cosφ = 1), 5 A at 30 VDC with
Control output
resistive load *2
Ambient operating temperature −20 to 55°C (with no icing)
Storage temperature −40 to 70°C (with no icing)
Ambient operating humidity 25% to 85%
21
H3DK-H
*1. DC ripple: 20% max. (A single-phase, full-wave rectifying power supply can be connected.)
*2. Refer to DC Power Consumptions (Reference Information) on page 27 for DC power consumptions.
*3. The control output ratings are for one H3DK operating alone.
If you operate two or more Timers side by side, refer to Installation Pitch and Output Switching Capacity (Reference Values) on the next page.
■ Characteristics
Accuracy of operating ● Installation Pitch and Output
±1% of FS max. (±1% ±10 ms max. at 1.2-s range)
time Switching Capacity (Reference
Setting error ±10% of FS ±0.05 s max. Values)
Influence of voltage ±0.5% of FS max. (±0.5% ±10 ms max. at 1.2-s range)
The relation between the installation pitch
Influence of tempera-
±2% of FS max. (±2% ±10 ms max. at 1.2-s range) and the load current is shown in the fol-
ture
lowing graph. (Except for the H3DK-GE)
Insulation resistance 100 MΩ min. at 500 VDC
If Timer is used under load conditions that
Between current-carrying metal parts and exposed non-current-carrying metal
parts: 2,000 VAC 50/60 Hz for 1 min. exceed the specified values, the tempera-
Between control output terminals and operating circuit: 2,000 VAC 50/60 Hz for ture inside the Timer will increase, reduc-
Dielectric strength
1 min.
Between contacts not located next to each other: 1,000 VAC 50/60 Hz for ing the life expectancy of internal parts.
1 min.
80
temperature in specifications
Maximum ambient operating
Static immunity Malfunction: 4 kV, Destruction: 8 kV
30
Vibration Destruction 0.75-mm single amplitude at 10 to 55 Hz for 2 h each in 3 directions
d = 0 mm
resistance Malfunction 0.5-mm single amplitude at 10 to 55 Hz for 10 min each in 3 directions 20
Life ex- Mechanical 10 million operations min. (under no load at 1,200 operations/h) 0 1 2 3 4 5 6
pectancy Load current (A)
Electrical 100,000 operations min. (5 A at 250 VAC, resistive load at 1,200 operations/h)
Degree of protection IP30 (Terminal block: IP20) Testing Method
Tested Timer: H3DK-H
Weight Approx. 120 g
Applied voltage: 240 VAC
Installation pitch: 0, 5, 10, and 50 mm
■ Applicable standards
Test Test Test Test Test
cURus: UL 508/CSA C22.2 No. 14 timer timer timer timer timer
EN 50274: Finger protection, back-of-hand proof 1 2 3 4 5
Safety standards EN 61812-1: Pollution degree 2, Overvoltage category III
CCC: Pollution degree 2, Overvoltage category II, section DB14048.5-2008 part 5-1
LR: Test Specification No. 1-2002 Category ENV 1.2 DIN Track Timer installation pitch: d
(EMI)EN61812-1
Radiated Emissions:EN 55011 class B
Emission AC Mains:EN 55011 class B
Harmonic Current:EN 61000-3-2
Voltage Fluctuations and Flicker:EN61000-3-3
(EMS)EN61812-1
ESD Immunity:EN 61000-4-2: 6 kV contact discharge,
EMC
8 kV air discharge
Radiated Radio-Frequency Electromagnetic Field Immunity (AM Radio Waves):
EN 61000-4-3: 10 V/m (80 MHz to 1 GHz)
Burst Immunity:EN 61000-4-4: 2 kV power line,
1 kV I/O signal line
Surge Immunity:EN 61000-4-5: 2 kV common mode,
1 kV differential mode
■ I/O
Input None
The Timer operates as soon as the Timer is turned ON. The
Output Control output Timer starts timing when the power is turned OFF and the output
is turned OFF when the time set on the dial elapses.
22
H3DK-H
Connections
■ Block Diagrams ■ Terminal Arrangement
H3DK-H H3DK-H
A1 15
Time specification
AC (DC) input Indicator circuit switches
R1
15
Power supply
circuit Oscillation circuit Counting circuit Output circuit
18 16
Power 18 16 A2
interruption
detection circuit
(DIN notation)
15
A1
A2
16 18
Nomenclature
H3DK-H Front View Bottom View
23
H3DK-H
Dimensions (Unit: mm)
■ Timers
H3DK-H
100
88.2
22.5 69.1
4
79 65.6 52 89.4
Operating Procedures
■ Basic Operation
Setting the Time Ranges Setting the Time
● Setting the Time Ranges ● Setting the Time
The scale multiplier can be changed with the timer range switch. The operation time is set with the main dial.
It can be changed between ×0.1 s and ×1 s for an S-series Timer
and between ×1 s and ×10 s for an L-series Timer.
Main dial
Time range
switch
■ Timing Charts
Rt
Rt t t
ON
Power (A1 and A2)
OFF
ON
Output relay: NO (15 and 18)
OFF
Indicator ON
OFF
t: Set time
S Series: 0.1 s min.
Rt: Minimum power-ON time
L Series: 0.3 s min.
(The output may never turn ON if the power is not ON for at least this time.)
24
H3DK
Safety Precautions
● Refer to Safety Precautions for All Timers.
Note: The following is common for all H3DK models.
25
H3DK
A2
A1
B1
H3DK
30 mm min.
Hook A2
A1 ● Environment
• When using the Timer in an area with excessive electronic
B1
H3DK Power noise, separate the Timer and input device as far as possible
Start
input
from the noise sources. It is also recommended to shield the
A2 input signal wiring to prevent electronic interference.
• The external impulse voltage entering across the power supply
Rectifier circuit
26
H3DK
● Wiring metal parts of the Timer. (Otherwise, the internal circuits of the
The H3DK-H acts like a high-impedance circuit. Therefore, the Timer may be damaged.)
Timer may not reset if it is influenced by inductive voltage. To • The H3DK-H uses a latching relay for the output. Shock, such
eliminate inductive voltage, the wires connected to the Timer as dropping the H3DK-H during shipment or handling, can
must be as short as possible and should not be installed parallel cause the output contacts to reverse to the neutral position.
to power lines. If the Timer is influenced by inductive voltage that Check the output status with a tester before using the H3DK-
H.
is 30% or more of the rated voltage, connect a CR filter with a
• The life expectancy of the control output contacts is greatly
capacitance of approximately 0.1 µF and a resistance of approx-
affected by switching conditions. Always confirm operation
imately 120 Ω or a bleeder resistor between the power supply
using the actual conditions and equipment before using the
terminals.
Timer and make sure that the number of switching operations
If there is any residual voltage due to current leakage, connect a presents no problems in performance. If Timer application is
bleeder resistor between the power supply terminals. continued after performance has deteriorated, insulation fail-
ure between circuits, burning of the control output relay, or
● Operating Frequency other problem will eventually occur.
• The H3DK-H may malfunction if it is used as shown below. Do • If the power supply voltage is gradually increased, a power
not use the H3DK-H in these ways. reset may occur or the Timer may time out. Use a switch,
Timer Repeatedly Times Out in Cycles of 3 s or Less relay, or other device with contacts to apply the power supply
voltage all at once.
3s 3s
or less or less • Make sure that residual voltage or inductive voltage is not
Power applied after the power turns OFF.
• Error in the operation time of the Timer is given as a percent-
Output
age of the full-scale time. The absolute value of the error will
In the above case, use the H3DK-M2/-M1 in D mode (signal not change even if the set time is changed. Therefore, always
OFF delay). use the Timer with the set time set as close as possible to the
full-scale value of the set time range.
● DC Power Consumptions (Reference Information)
• When switching a microload, check the specified minimum
H3DK-M2/-S2 At 24 VDC: 1.2 W max.
load given for the Timer model you are using.
H3DK-M1/-S1 At 24 VDC: 1.1 W max. • When setting the operating time, do not turn the dial beyond
H3DK-F At 24 VDC: 1.1 W max. the scale range.
H3DK-G At 24 VDC: 1.2 W max. • If better accuracy is required in the set time, adjust the dial
H3DK-HBS/-HBL At 24 VDC: 1.2 W max.
while measuring the operation time.
• If the Timer is reset immediately after timing out, make sure
● Other Precautions that the circuit configuration allows sufficient resetting time.
Errors will occur in the sequence if there is not sufficient reset-
• If the Timer is mounted on a control panel, dismount the Timer ting time.
from the control panel before carrying out a voltage withstand • When directly switching a DC load, the switching capacity will
test between the electric circuits and non-current-carrying be lower than when switching an AC load.
27
H3DK
Track Mounting Products (Sold Separately) (Unit: mm)
DIN Track
PFP-100N
7.3±0.15
PFP-50N 4.5
35±0.3 27±0.15
15 25 25 25 25 15 (5)* 1
10 10
1,000 (500)*
*Dimensions in parentheses are for the PFP-50N.
DIN Track
16
PFP-100N2
4.5
35±0.3 27 24 29.2
15 25 25 25 25 15 1 1.5
10 10
1,000
End Plate 10
6.2
PFP-M 1.8
M4x8
panhead
screw 1
50 35.5 35.3
1.8
11.5
10 1.3
M4 screw 4.8
and washer
16
Spacer
5 12
PFP-S
34.8
44.3
16.5
Note 1: Order the above products in multiples of 10.
Note 2: The Tracks conform to DIN standards.
28
Warranty and Application Considerations
Read and Understand This Catalog
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have
any questions or comments.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS,
OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON
CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE
PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED,
INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE
MODIFICATION OR REPAIR.
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of
products in the customer's application or use of the products.
Take all necessary steps to determine the suitability of the product for the systems, machines, and equipment with which it will
be used.
Know and observe all prohibitions of use applicable to this product.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON
PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR
SYSTEM.
Disclaimers
PERFORMANCE DATA
Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a
warranty. It may represent the result of OMRON's test conditions, and the users must correlate it to actual application
requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability.
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons. Consult with
your OMRON representative at any time to confirm actual specifications of purchased product.
OMRON ASIA PACIFIC PTE. LTD. OMRON (CHINA) CO., LTD. © OMRON Corporation 2010 All Rights Reserved.
No. 438A Alexandra Road # 05-05/08 (Lobby 2), Room 2211, Bank of China Tower, In the interest of product improvement,
Alexandra Technopark, 200 Yin Cheng Zhong Road, specifications are subject to change without notice.
Singapore 119967 PuDong New Area, Shanghai, 200120, China CSM_1_2_0711 Printed in Japan
Tel: (65) 6835-3011/Fax: (65) 6835-2711 Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200 Cat. No. L118-E1-02 0910