Documente Academic
Documente Profesional
Documente Cultură
RMT-835
Link
DATA BACKUP
CAMERA SECTION ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
ADJUSTMENT PROGRAM
ERROR
• Use this Service Manual together with the Automatic Adjustment Program (HDR-SR7 Series Auto-Adj
Ver_1.0r01.exe).
2007E0500-1
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ © 2007.5
9-852-202-51 Sony EMCS Co. Published by Kohda TEC
6. ADJUSTMENTS
Destination
Destination data write
Data Write
USB Serial No.
USB serial No. input
Input
(Note 1) Origin oscillation check z
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
VIDEO VIDEO OUT level check
z z z
adjustment COMPONENT OUT Y level adj.
COMPONENT OUT Pb level adj.
COMPONENT OUT Pr level adj.
Initialization of
Initialization of EEPROM Data
EEPROM Data
STEADY HALL adj. (Note 3)
CAMERA HALL adj.
z z z z z
adjustment 1 MR adj.
Differential gain adj.
CAMERA Flange back adj. z z z
adjustment 2
CAMERA Flange back check z z z
adjustment 3
F No. & ND light qualiy
standard data input
Mechanical shutter adj
Linear matrix adj.
CAMERA AWB standard data input z z z z z
adjustment 4 LV standard data input
AWB adj.
Color reproduction adj.
MAX GAIN adj.
CAMERA White defect adj.
z z z
adjustment 5 Black defect adj.
CAMERA Strobe light level adj.
z
adjustment 6 Strobe white balance adj.
CAMERA Steady shot check (Note 2) z
adjustment 7
CAMERA GYRO sensor sensitivity adj. (Note 3) z z
adjustment 8
LCD/EVF automatic adj.
V-COM adj.
LCD
Transmissive mode white balance adj. z z z z
adjustment
Reflective mode white balance adj.
Sample hold phase adj.
EVF LCD/EVF automatic adj.
adjustment z z z z
White balance adj.
(Note 3)
Touch panel Touch panel adj. z
adjustment
AUDIO
Internal 3ch microphone sensitivity adj. z z
adjustment
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-2
1-2. List of service tools
• Oscilloscope • Color monitor • Vectorscope • Frequency counter
• Amplifier built-in speaker for PC • Adjustment sound source file
Flange back
Minipattern box adjustment jig Siemens star chart
J-6082-353-B J-6082-563-A J-6080-875-A
Handycam Station
Camera table AC adaptor
DCRA-C180/C181
J-6082-384-A AC-L200/L200B
1-821-168-11/21
1-479-285-21
(Note 2)
Fig. 6-1-1
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-3
6-1. CAMERA SECTION ADJUSTMENTS
1-1-1. Preparations
L = 1 m (PTB-450)
1) Connect the equipment for adjustments according to Fig. 6-1-3.
L = 40 cm (PTB-1450)
Pattern box
Front of the lens
L Camera
Fig. 6-1-2
Handycam Station
DCRA-C180/C181
(1-821-168-11/21)
USB cable
To USB jack (1-829-579-41)
To COMPONENT
OUT jack
HASP Key
To DC IN jack
To A/V jack
Color monitor
Vectorscope
Terminated Video
75 Ω
Fig. 6-1-3
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-4
1-1-2. Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments without inserting disc.
2. Order of Adjustments
Basically carry out adjustments in the order given.
H
Electronic beam scanning frame
Yellow
Magenta
White
Cyan
C=D=0
Green
C D
Red
Blue
Magenta
Yellow
Green
White
Cyan
Blue
Red
CRT picture frame
V
A B A=B B A
Fig. b (monitor TV picture)
Fig. a Enlargement
(VIDEO terminal of A/V jack
output waveform)
Difference in level
Fig. 6-1-4
3. Subjects
1) Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, ad-
just the picture frame as shown in Fig. 6-1-4. (Color reproduc-
tion adjustment frame)
2) Clear chart (AWB adjustment frame)
Shoot the color bar chart. Then adjust the zoom to TELE side
from WIDE side, and stop it when the black frame of the chart White
disappears. Remove the color bar chart from pattern box and 841 mm
insert a clear chart in its place.
Black
3) Chart for flange back adjustment
Join together a piece of white A0 size paper (1189 mm × 841
mm) and a piece of black paper to make the chart shown in
Fig. 6-1-5.
1189 mm
Note: Use a non-reflecting and non-glazing vellum paper. The
size must be A0 or larger and the joint between the white Fig. 6-1-5
and black paper must not have any undulations.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-5
4. Preparing the Flash Adjustment Box
A dark room is required to provide an accurate flash adjustment.
If it is not available, prepare the flash adjustment box as given
below;
730 mm 700 mm
Fig. 6-1-6
woody board A
woody board B
woody board A
woody board B
woody board C
Fig. 6-1-7
L = 50 cm
L Camera
Background paper
Fig. 6-1-8
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-6
1-2. ADJUSTMENT PROGRAM 3. Function of Each Button on Main Menu Screen
The HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E are adjusted by When the Automatic Adjustment Program started, the Main Menu
the Automatic Adjustment Program. The Automatic Adjustment screen in Fig. 6-1-9 will appear. On this screen, select each adjust-
Program enters automatically via the SeusEX the adjustment op- ment section.
erations that were formerly entered manually by the adjustment
remote commander (some items may be adjusted by manual op-
eration on the operation screen of the SeusEX).
2 [CONNECT] button
The mode of Camcorder is switched to the Adjustment Mode.
When the Adjustment Mode has switched normally, the op-
eration of the buttons 4 - qa is enabled.
3 [END] button
The mode of Camcorder is switched to the normal mode.
When the normal mode has switched correctly, the Automatic
Adjustment Program is finished.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-7
4. Setting of Adjustment Mode 5. Release of Adjustment Mode
Before performing the adjustment, “Setting of Adjustment Mode” To finish the adjustment, be sure to perform “Release of Adjust-
is required. ment Mode”.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-8
1-3. HDD SYSTEM ADJUSTMENTS
When the HDD is replaced, the following VBScript files are used.
The Automatic Adjustment Program (HDR-SR7 Series Auto-Adj
Ver 1.[]r[][].exe) is not used.
• CheckHDDError.vbe
• SetFactoryCheckDefault.vbe
• SetFactoryCheckFull.vbe
• ExecAfterFactoryCheck.vbe
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-9
1. HDD Replacing Procedure
Note: During the execution of Factory Check, the LCD screen of
the camcorder becomes gray.
When the Factory Check finished, the LCD screen changes
as follows:
When Factory Check is OK: Camera image display
When Factory Check is NG: Blue display
Yes No
New HDD Reused HDD
Is replacement HDD new one?
Start
Wait until “JOB Success” Wait until “JOB Success”
message is displayed message is displayed
(several seconds) (several seconds)
Connect the camcorder to the PC
with a USB cable, and turn on the
power switch.
Turn off the power of camcorder.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-10
1-4. DESTINATION DATA WRITE 2. Destination Data Write
Note: The DESTINATION DATA WRITE can be set with the [Writing method]
Service board only. 1) Select the model name with the Model Name List.
Performing the DESTINATION DATA WRITE with other
than the Service board causes the error (E:20:00 will be
blinking) and the power to be shut down.
2 3
Fig. 6-1-10
3 Destination List
Selects the written destination.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-11
3. Selectable Language Table
SELECTABLE LANGUAGE
Traditional Chinese
Simplified Chinese
DSTINATION
Simplified English
Canadian French
Braz.Portuguese
Portuguese
AREA
Hungarian
Japanese
Indonesia
Espanyol
German
Spanish
Russian
Persian
English
Turkish
Korean
Melayu
French
Arabic
Czech
Greek
Polish
Italian
Dutch
Thai
J1 J z
NTSC model
U2 US z a a a a
E23 E z a a a a a a
KR2 KR a a a a a z a
JE3 JE z a a a a a a
CA2 CND z a a a a a a
E34 E z a a a a a a a a a a a a a a a a
HK1 HK z a a a a a a a a a a a a a a a a
PAL model
AU2 AUS z a a a a a a a a a a a a a a a a
CN2 CH a a a a a a a z a a a a a a a a a
JE3 JE z a a a a a a a a a a a a a a a a a a a a
CEN AEP z a a a a a a a a a a a a a a a a
CEH UK z a a a a a a a a a a a a a a a a
z: INITIAL LANGUAGE
Table 6-1-2
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-12
1-5. USB SERIAL No. INPUT 1. Function of Each Button on USB Serial No. Input
The set is shipped with a unique ID (USB Serial No.) written in it. Screen
This ID has not been written in a new board for service, and there- Click the [USB SERIAL No. INPUT] button on the Main Menu screen,
fore it must be entered after the board replacement. and the “USB SERIAL No. INPUT” screen in Fig. 6-1-11 will
If original ID can be read from the board before replacement, read appear.
it from the board before replacement using the “SERIAL READ/
1
WRITE” screen, and then write it after replacement.
If original ID cannot be read from the board before replacement,
write the ID for service using the “MANUAL WRITE” screen.
(The ID for service is different from the ID written when the set is
shipped.) Enter the PRODUCT ID (last 5 characters of model name) 3
and SERIAL No. into the screen and write them. 2
Fig. 6-1-11
2 Display area
The “PRODUCT ID”, “SERIAL No.” and “ASCII TRANS-
LATION” are displayed.
For the “ASCII TRANSLATION”, the last 5 characters of
model name are displayed if the PRODUCT ID is set from the
model name in the MANUAL WRITE. For the PRODUCT ID
set in the factory, the model name is not displayed but “?” etc.
will be displayed.
6 Input area
Enter “PRODUCT ID” and “SERIAL No.” when writing the
ID for service.
The “PRODUCT ID” is set from the last 5 characters of model
name if the model name is selected.
For the “SERIAL No.”, read it from the label on the camera
body and enter it.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-13
1-6. VIDEO SYSTEM ADJUSTMENTS
2 3
Fig. 6-1-12
2 [Preparation] button
Notes for adjustment or jigs used are displayed.
3 [Start] button
“Video Adjustment” starts.
Table 6-1-3
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-14
3. Origin Oscillation Check
Check the frequency of the clock for synchronization.
If deviated, the synchronization will be disrupted and the color
will become inconsistent.
Subject Not required
Measurement Point R1316 (Pin K5 of IC1301 (CHCK))
on VC- 504 board
Measuring Instrument Frequency counter
Specified value f = 40459541 ± 809 Hz (SR5/SR5C)
f = 44505494 ± 890 Hz (SR7/SR8)
f = 31185000 ± 624 Hz (SR5E)
f = 37125000 ± 743 Hz (SR7E/SR8E)
Switch setting
1) POWER ............................................................. MOVIE mode
Checking method:
1) Check that the frequency (f) satisfies the specified value.
R1316
IC1301
Fig. 6-1-13
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-15
4. VIDEO Adjustment 4) After that, the following screen is displayed during the execu-
[Automatic Adjustment Program execution items and tion of “3. S VIDEO OUT Chroma Level Adj.”. Using the [Up]/
sequence] [Down] button on the screen, adjust so that the Cr signal level
1. Data Setting during Video Adj. and the Cb signal level satisfies the specified value. After the
2. S VIDEO OUT Y Level Adj. adjustment, check that the burst level of the chroma signals
3. S VIDEO OUT Chroma Level Adj. satisfies the specified value, and click the [End] button in the
4. VIDEO OUT Level Check screen.
5. COMPONENT OUT Y Level Adj.
6. COMPONENT OUT Pb Level Adj.
7. COMPONENT OUT Pr Level Adj.
8. Release of Data Setting during Video Adj.
[Adjusting method]
1) Click the [Start] button of the VIDEO Adjustment.
2) The Automatic Adjustment Program executes the “1. Data
Setting during Video Adj.”.
3) If “1. Data Setting during Video Adj.” completed successfully,
the following screen is displayed during the execution of “2. S
VIDEO OUT Y Level Adj.”. Using the [Up]/[Down] button on
the screen, adjust so that the Y signal level satisfies the speci-
fied value. After the adjustment, click the [End] button in the
screen.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-16
6) After that, the following screen is displayed during the execu- 8) After that, the following screen is displayed during the execu-
tion of “5. COMPONENT OUT Y Level Adj.”. Using the [Up]/ tion of “7. COMPONENT OUT Pr Level Adj.”. Using the [Up]/
[Down] button on the screen, adjust so that the Y signal level [Down] button on the screen, adjust so that the Pr signal level
satisfies the specified value. After the adjustment, check that satisfies the specified value. After the adjustment, check that
the sync level of the Y signals satisfies the specified value, and the sync level of the Pr signals satisfies the specified value,
click the [End] button in the screen. and click the [End] button in the screen.
7) After that, the following screen is displayed during the execu- 9) If the [End] button is clicked, “8. Release of Data Setting dur-
tion of “6. COMPONENT OUT Pb Level Adj.”. Using the [Up]/ ing Video Adj.” will be executed.
[Down] button on the screen, adjust so that the Pb signal level 10) Upon successful completion of all item the VIDEO Adjust-
satisfies the specified value. After the adjustment, check that ment, the following message is displayed. Click the [OK] but-
the sync level of the Pb signals satisfies the specified value, ton.
and click the [End] button in the screen.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-17
1-7. CAMERA SYSTEM ADJUSTMENTS
2
1
3 4
Fig. 6-1-14
3 [Preparation] button
Notes for adjustment or jigs used are displayed.
4 [Start] button
Each adjustment from “Camera Adjustment 1” to “Camera
Adjustment 8” starts.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-18
2. Adjustment Items of Camera System Adjustment
The adjustment items of camera system adjustment are as listed in The adjustment conditions of the subject and filter vary depend-
Table 6-1-4. The Automatic Adjustment Program divides the ad- ing on which item is adjusted. The Adjustment Program displays
justment items into eight, camera adjustment 1-8. Clicking either an instruction for the subject and filter as a message during the
CAMERA Adjustment Start button allows the adjustment item adjustment.
which corresponds to that button to be executed.
Adjusting Address
Button Name Adjustment Subject
Block Page Address
11 80 0F00 to 0FFF, 6300 to 6FFF
Initialization of
Initialization of EEPROM data Not required 7C00 to 7CFF, 7E00 to 7F7F
EEPROM Data 11 80
(Note 1 only)
STEADY HALL Adj. 11 80 7F04 to 7F0F
(Note 1 only)
HALL Adj. Not required 11 80 69D0 to 69D8
CAMERA
MR Adj. 11 80 6F30, 6F40 to 6F4F
Adjustment 1
Clear chart (All White)
Differential Gain Adj. (Shoot the clear chart with the zoom TELE 11 80 6E00 to 6EB3
end.)
Siemens star chart with ND filter for
minipattern box (Note 3) or
CAMERA Flange back adjustment jig 80 6F20 to 6F3F
Flange Back Adj. 11
Adjustment 2
Flange back adjustment chart and
subject more than 500 m away
CAMERA - - -
Flange Back Check Siemens star chart
Adjustment 3
F No. & ND Light Quality 80
11 69E0 to 69EF
Standard Data Input
Mechanical Shutter Adj. Not required 11 80 69B0 to 69B5, 6F7A to 6F7F
Linear Matrix Adj. 80 69BE to 69CF, 6F60 to 6F71,
11
6FC8 to 6FEB
AWB Standard Data Input 11 80 6F88 to 6F97, 6FF0 to 6FF7
Clear chart (All White frame)
LV Standard Data Input 11 80 69DC, 69DD
AWB Adj. Clear chart (All White frame) 80 6F84 to 6F87, 6F98 to 6FA7,
11
Filter C14 for color temperature correction 6FF8 to 6FFF
CAMERA
Adjustment 4 AWB Check Clear chart (All White frame) - - -
ND filter 1.0, 0.4 and 0.1
Color Reproduction Adj. & 80 6FA8 to 6FB7
11
Check (Indoor HD) Color bar chart
Color Reproduction Check (Color reproduction adjustment frame)
- - -
(Indoor SD)
Color bar chart
Color Reproduction Check - - -
(Color reproduction adjustment frame)
(Outdoor HD, Outdoor SD)
Filter C14 for color temperature correction
MAX GAIN Adj. Clear chart (Center frame) 11 80 69DE
HS White Defect Adj. 11 87 0E50 to 0EC7
White Defect Adj. 11 87 0200 to 0DFF
White Defect Adj. Not required 0E26 to 0E37, 0F2A to 0F3B,
11 87
CAMERA (FD white point) 0F7E to 0F8F, 0FD2 to 0FE3
Adjustment 5 White Defect Check - - -
Clear chart (All White) 0E00 to 0E25, 0F00 to 0F29,
Black Defect Adj. (Shoot the clear chart with the zoom TELE 11 87 0F54 to 0F7D, 0FA8 to 0FD1,
end.) 0FFC to 0FFF
CAMERA Strobe Light Level Adj. 11 80 69B8 to 69BD
Flash adjustment box
Adjustment 6 Strobe White Balance Adj. 11 80 6F80, 6F81
CAMERA Steady Shot Check - - -
Not required
Adjustment 7 (Note 2 only)
CAMERA GYRO Sensor Sensitivity Adj. 80 7F12, 7F13
Not required 11
Adjustment 8 (Note 1 only)
Note 1: HDR-SR7/SR7E/SR8/SR8E only
Note 2: HDR-SR5/SR5C/SR5E only
Note 3: Dark Siemens star chart.
Table 6-1-4
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-19
3. Initialization of EEPROM Data 4. CAMERA Adjustment 1
The EEPROM data of the board for service has already been ini- [Automatic Adjustment Program execution items and
tialized, not requiring further initialization when the board is re- sequence]
placed. 1. Data Setting during Camera Adj.
Execute this processing only when the EEPROM is replaced. 2. STEADY HALL Adj. (SR7/SR7E/SR8/SR8E only)
If the EEPROM data is initialized, all the camera adjustment data 3. HALL Adj.
is also initialized. All items of the camera adjustments must be 4. MR Adj.
performed after the initialization of EEPROM data. 5. Differential Gain Adj.
6. Release of Data Setting during Camera Adj.
[Initializing method]
1) Click the [Initialization of EEPROM Data] button on Camera [Adjusting method]
Adjustment screen, and the following screen will appear. 1) Click the [Start] button of the CAMERA Adjustment 1.
2) The Automatic Adjustment Program executes “1. Data Setting
during Camera Adj.”.
3) If “1. Data Setting during Camera Adj.” completed success-
fully, and the items from “2. STEADY HALL Adj.” to “4. MR
Adj.” will be executed.
4) Upon successful completion of the “4. MR Adj.”, the follow-
ing message is displayed. Set the subject in accordance with
the message.
5) Click the [OK] button, and the “5. Differential Gain Adj.” will
be executed.
6) Upon completion of “5. Differential Gain Adj.”, “6. Release
of Data Setting during Camera Adj.” is executed.
7) Upon successful completion of all items of the CAMERA Ad-
justment 1, the following message is displayed. Click the [OK]
button.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-20
5. CAMERA Adjustment 2 [Preparation (Using the flange back adjustment jig)]
(Using the minipattern box or flange back adjust- (Luminance: 300 to 400 lux)
ment jig) Note: When using the flange back adjustment jig, take care of the
[Automatic Adjustment Program execution items and following points:
sequence] • For the illumination, use a light source such as an incan-
1. Data Setting during Camera Adj. descent lamp or inverter type fluorescent light free from
2. Flange Back Adj. flickering.
3. Release of Data Setting during Camera Adj. • Do not make an adjustment in the environment where fluo-
rescent lamp flickering occurs even if the illuminance can
[Preparation (Using the minipattern box)] be ensured with the room illumination only. Use an in-
1) The minipattern box is installed as shown in the following fig- candescent lamp or inverter type fluorescent light at a place
ure. free from the influence of room illumination.
Note: The attachment lenses are not used. 1) Install the flange back adjustment jig so that the distance be-
2) Install the minipattern box so that the distance between it and tween it and the front of lens of camera is less than 3 cm.
the front of lens of camera is less than 3 cm. 2) Make the height of flange back adjustment jig and the camera
3) Make the height of minipattern box and the camera equal. equal.
4) Check the output voltage of the regulated power supply is the 3) Check that the center of chart meets the center of shot image
specified voltage ± 0.01 Vdc. screen with the zoom lens at TELE end and WIDE end respec-
5) Check that the center of Siemens star chart meets the center of tively.
shot image screen with the zoom lens at TELE end and WIDE Below 3 cm
end respectively. Flange back adjustment jig
Red (+)
Black (–)
Yellow (SENS +) 4) If the [OK] button is clicked, “2. Flange Back Adj.” and “3.
White (SENS –) Release of Data Setting during Camera Adj.” will be executed.
Need not connected
5) Upon successful completion of all items of the CAMERA
Black (GND) Adjustment 2, the following message is displayed. Click the
[OK] button.
Fig. 6-1-15
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-21
6. CAMERA Adjustment 2 6-2. CAMERA Adjustment 2 (2)
(Using the flange back adjustment chart and [Automatic Adjustment Program execution items and
subject more than 500 m away) sequence]
6-1. CAMERA Adjustment 2 (1) 1. Data Setting during Camera Adj.
[Automatic Adjustment Program execution items and 2. Flange Back (2) Adj.
sequence] 3. Release of Data Setting during Camera Adj.
1. Data Setting during Camera Adj.
2. Flange Back (1) Adj. [Preparation]
3. Release of Data Setting during Camera Adj. 1) Set the zoom lens to the TELE end and expose a subject that is
more than 500 m away.
[Preparation] (subjects with clear contrast such as building, etc.)
1) Place the Flange back adjustment chart at 2 m position away (Nearby subjects less than 500 m away should not be in the
from the lens. screen)
2) Check that the center of Flange back adjustment chart meets
the center of shot image screen with the zoom lens at TELE [Adjusting method]
end and WIDE end respectively. 1) Click the [Start $2%] button of the CAMERA Adjustment 2.
2) The Automatic Adjustment Program executes “1. Data Setting
[Adjusting method] during Camera Adj.”.
1) Click the [Start $1%] button of the CAMERA Adjustment 2. 3) Upon successful completion of the “1. Data Setting during
2) The Automatic Adjustment Program executes “1. Data Setting Camera Adj.”, the following message is displayed. Set the sub-
during Camera Adj.”. ject by referring to “Preparation”.
3) Upon successful completion of the “1. Data Setting during
Camera Adj.”, the following message is displayed. Set the sub-
ject by referring to “Preparation”.
4) If the [OK] button is clicked, “2. Flange Back (2) Adj.” will be
executed.
4) If the [OK] button is clicked, “2. Flange Back (1) Adj.” and “3. The following message is displayed during the execution of
Release of Data Setting during Camera Adj.” will be executed. adjustment, and then place the ND filter on the lens so as to
5) Upon successful completion of all items of the CAMERA obtain the optimum image.
Adjustment 2 (1), the following message is displayed. Click
the [OK] button.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-22
7. CAMERA Adjustment 3
[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Flange Back Check
3. Release of Data Setting during Camera Adj.
[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 3.
2) The Automatic Adjustment Program executes “1. Data Setting
during Camera Adj.”.
3) Upon successful completion of the “1. Data Setting during
Camera Adj.”, the following message is displayed. Set the sub-
ject in accordance with the message.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-23
8. CAMERA Adjustment 4 5) If the [OK] button is clicked, the following screen will appear,
[Automatic Adjustment Program execution items and and then adjust the zoom and the camera direction to set the
sequence] picture frame. After the setting finished, click the [End] but-
1. Data Setting during Camera Adj. ton.
2. F No. & ND Light Quality Standard Data Input
3. Mechanical Shutter Adj.
4. Linear Matrix Adj.
5. Picture Frame Setting (Color Reproduction Adjustment Frame)
6. Picture Frame Setting (All White Frame)
7. AWB Standard Data Input
8. LV Standard Data Input
9. AWB Adj.
10. AWB Check
11. Color Reproduction Adj. & Check (Indoor HD)
12. Color Reproduction Check (Indoor SD)
13. Color Reproduction Check (Outdoor HD, Outdoor SD)
14. Picture Frame Setting (Center Frame)
15. MAX GAIN Adj.
16. Release of Data Setting during Camera Adj.
[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 4.
2) The Automatic Adjustment Program executes “1. Data Setting
during Camera Adj.”.
3) If “1. Data Setting during Camera Adj.” completed success-
fully, and the items from “2. F No. & ND Light Quality Stan-
dard Data Input” to “4. Linear Matrix Adj.” will be executed.
4) Upon successful completion of the “4. Linear Matrix Adj.”,
the following screen is displayed during the execution of “5.
Picture Frame Setting (Color Reproduction Adjustment
Frame)”. Set the subject in accordance with the message.
The buttons on this screen provide the following functions:
[Save the position] button
Saves the camera zoom and focus position data.
[Load the position] button
Reads the camera zoom and focus position data saved last and
moves the camera zoom and focus to that position.
Note 1: The zoom and focus position data are saved with
“HDR_SR7_ZoomFocusData.txt” file name in the same
holder as the Automatic Adjustment Program.
No position data can be read if this file is moved or de-
leted.
Note 2: Only the latest position data can be saved. If the [Save
the position] button is clicked, the latest data are saved
over writing the previous data.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-24
6) After setting the picture frame, if the [End] button is clicked, 8) Upon successful completion of the “10. AWB Check”, the fol-
“6. Picture Frame Setting (All White Frame)” is executed. The lowing message is displayed. Then, change the chart in accor-
following messages are displayed in the order given below dance with the message.
during the execution. Then, set the picture frame in accordance
with the messages.
R MG
7) After the setting, if the [OK] button is clicked, the adjustment
items from “7. AWB Standard Data Input” to “10. AWB Check”
are executed. During the execution, the following messages YE
are displayed in the order given below. Place or remove the
B-Y
filters on the lens in accordance with the messages.
B
G CY
NTSC model
Burst position
R MG
YE
B-Y
G CY
NTSC model
Burst position
Fig. 6-1-17
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-25
10) After the checking of the Indoor SD mode, “13. Color Repro- 11) Upon successful completion of the “13. Color Reproduction
duction Check (Outdoor HD, Outdoor SD)” is executed. The Check (Outdoor HD, Outdoor SD)”, the following message is
following messages are displayed in order, and then operate displayed. Then, change the chart in accordance with the mes-
the vectorscope to make a check with the color reproduction sage.
frame in accordance with the message.
12) After the setting, if the [OK] button is clicked, the following
message is displayed during the execution of “14. Picture Frame
Setting (Center Frame)”. Set the subject in accordance with
the message, and then check the size of clear chart shot on the
monitor screen.
CY
G
NTSC model
Burst position
YE
B-Y
B
CY
G
NTSC model
Burst position
Fig. 6-1-18
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-26
9. CAMERA Adjustment 5 [Automatic Adjustment Program execution items and
Note: Before performing the defect adjustment, make sure that sequence]
the lens temperature of the camcorder exceeds 39 ºC. 1. Data Setting during Camera Adj.
2. HS White Defect Adj.
[Preparation (Temperature Check)] 3. White Defect Adj.
1) Click the [Preparation] button of the CAMERA Adjustment 5 4. White Defect Adj. (FD white point)
to display the Preparation screen. 5. White Defect Check
2) Click the [Temperature Check] button of the Preparation screen, 6. Black Defect Adj.
the following screen will appear. 7. Release of Data Setting during Camera Adj.
[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 5.
2) The Automatic Adjustment Program executes “1. Data Setting
during Camera Adj.”.
3) If “1. Data Setting during Camera Adj.” completed success-
fully, and the items from “2. HS White Defect Adj.” to “5.
White Defect Check” will be executed.
4) If “5. White Defect Check” completed successfully, the fol-
lowing message is displayed. Set the subject in accordance
with the message.
5) Click the [OK] button, and the “6. Black Defect Adj.” will be
executed.
6) Upon completion of “6. Black Defect Adj.”, “7. Release of
Data Setting during Camera Adj.” is executed.
[Checking method] 7) Upon successful completion of all items of the CAMERA Ad-
Click the [Start] button of the Temperature Check, and the justment 5, the following message is displayed. Click the [OK]
camcorder will go in the Temperature Check mode and the tem- button.
perature check result will be displayed on the LCD screen. Per-
form the aging if the check result is NG (below 39 ºC). To exit the
Temperature Check mode, click the [Stop] button.
[Aging method]
Set the camcorder to the Movie mode, and place the LCD screen
in the “reverse-closed” state. (In this state, the temperature rises
more quickly than that in other states.)
Set the camcorder to the Temperature Check mode, and wait until
the LCD screen display changes from NG (grid pattern) to OK
(color bars).
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-27
10. CAMERA Adjustment 6 11. CAMERA Adjustment 7
Note: “CAMERA Adjustment 6” is available only once after the (HDR-SR5/SR5C/SR5E only)
power is turned on. If the adjustment is retried, turn off the [Automatic Adjustment Program execution items and
power and turn on again. sequence]
1. Data Setting during Camera Adj.
[Automatic Adjustment Program execution items and 2. Steady Shot Check
sequence] 3. Release of Data Setting during Camera Adj.
1. Data Setting during Camera Adj.
2. Strobe Light Level Adj. [Adjusting method]
3. Strobe White Balance Adj. 1) Click the [Start] button of the CAMERA Adjustment 7.
4. Release of Data Setting during Camera Adj. 2) The Automatic Adjustment Program executes “1. Data Setting
during Camera Adj.”.
[Adjusting method] 3) Upon successful completion of the “1. Data Setting during
1) Click the [Start] button of the CAMERA Adjustment 6. Camera Adj.”, the following message is displayed.
2) The Automatic Adjustment Program executes “1. Data Setting With the camcoder in stationary state, click the [OK] button.
during Camera Adj.”.
3) Upon successful completion of the “1. Data Setting during
Camera Adj.”, the following message is displayed. Set the sub-
ject in accordance with the message.
(For the Flash adjustment box, refer to “4. Preparing the Flash
Adjustment Box” (see page 6-6).)
4) If the [OK] button is clicked, “2. Steady Shot Check” is ex-
ecuted.
Upon successful completion of the “2. Steady Shot Check”,
the following message is displayed. Check that the steadyshot
function operates normally in accordance with the message.
4) Press the [OK] button, and the items “2. Strobe Light Level
Adj.” and “3. Strobe White Balance Adj.” will be executed.
5) Upon completion of “3. Strobe White Balance Adj.”, “4. Re-
lease of Data Setting during Camera Adj.” is executed
6) Upon successful completion of all items of the CAMERA Ad-
justment 6, the following message is displayed. Click the [OK] 5) If the [OK] button is clicked, “3. Release of Data Setting dur-
button. ing Camera Adj.” is executed.
6) Upon successful completion of all items of the CAMERA
Adjustment 7, the following message is displayed. Click the
[OK] button.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-28
12. CAMERA Adjustment 8 Preparation:
(HDR-SR7/SR7E/SR8/SR8E only) 1) Read the PITCH sensor (CM-077 board SE7202) sensitivity
Perform this adjustment only when replacing the GYRO sensor or written on repair parts, and named this as S7202.
lens block. When the microprocessor, circuit etc. is damaged, don't 2) Read the YAW sensor (CM-077 board SE7201) sensitivity writ-
perform this adjustment but check the operations only. ten on repair parts, and named this as S7201.
12-1. Preparation when the GYRO sensor or the CM- CM-077 BOARD (SIDE A)
077 board is replaced
Note down the sensitivity displayed on the GYRO sensor of the re-
pair parts. At this time, note down also to which board it was attached
to.
Be sure to check because if attached incorrectly, the screen will vi-
brate up and down or left and right during the steady shot operations.
2
SE7202
Adjustment Address 7F12, 7F13
SE7201
2 1
YY
Note: The sensor sensitivity of SE7201 and SE7202 of the CM-
PP
077 board is written only repair parts. 3 4
1
4
PP: PITCH sensor sensitivity S7202
Fig. 6-1-19
Description example:
For the sensor sensitivity value 60
4 3
6 0
1 2
Hand Writing
Fig. 6-1-20
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-29
12-2. Preparation when the lens is replaced 12-3. GYRO Sensor Sensitivity Adjustment
Note down the PITCH/YAW data on the replacement lens for repair. [Adjusting method]
1) Click the [Start] button of Camera Adjustment 8, and the fol-
Adjustment Block 11
lowing screen will appear.
Adjustment Page 80
Adjustment Address 7F12, 7F13
Note: The PITCH/YAW data of lens is written only repair parts.
Preparation:
1) Read the PITCH data written on repair parts, and named this
as L1.
2) Read the YAW data written on repair parts, and named this as
L2 .
PITCH/YAW Data
2) Input the sensitivity of respective sensors (S7201, S7202) read at
X.XX / X.XX “Preparation” into the screen.
If only either sensor was replaced, give a check to the checkbox
YAW data t L2 for the sensor not replaced at the lower left of the screen.
3) Input the PITCH/YAW data of lens (L1, L2) read at “Prepara-
PITCH data t L1 tion” into the screen.
If the lens was not replaced, give a check to the checkbox at
Fig. 6-1-21 the lower left of the screen.
4) Click the [OK] button, and the adjustment data is then calcu-
lated from the sensor sensitivity value and the calculation re-
sult is written to the memory in the camera.
5) Upon successful completion of the data writing, the following
screen will appear. Check that the steady shot function oper-
ates normally.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-30
1-8. LCD/EVF SYSTEM ADJUSTMENTS 1 [To Menu] button
The Main Menu screen comes back.
1. Function of Each Button on LCD/EVF System
Adjustment Screen 2 [Start] button
Click the [LCD/EVF SYSTEM ADJUSTMENT] button on the Main Each adjustment “LCD Adjustment”, “EVF Adjustment” or
Menu screen, and the “LCD/EVF SYSTEM ADJUSTMENT” “Touch Panel Adjustment” starts.
screen in Fig. 6-1-22 will appear.
3 [Release Data Setting] button
1 The data setting at the adjustment is cancelled.
During the data setting, the button color changes from “white”
to “red”. When the data setting is cancelled, the button color
returns to “white”.
(Use this button when an error occurred in the LCD/EVF ad-
justment. If the adjustment completed successfully, the data
setting is automatically cancelled and the button color returns
to “white”.)
Fig. 6-1-22
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-31
3. LCD Adjustment 4) If the [End] button is clicked, the following screen is displayed
[Automatic Adjustment Program execution items and during the execution of “4. Transmissive Mode White Balance
sequence] Adj.”. Check that the LCD screen is not colored. If colored,
1. Data Setting during LCD/EVF Adj. using the [Up]/[Down] button on the screen, adjust so that the
2. LCD Automatic Adj. LCD screen is not colored. After the adjustment, click the [End]
(VCO Adj., Contrast Adj.) button in the screen.
3. V-COM Adj.
4. Transmissive Mode White Balance Adj.
5. Reflective Mode White Balance Adj.
6. Sample Hold Phase Adj.
7. Release of Data Setting during LCD/EVF Adj.
[Adjusting method]
1) Click the [Start] button of the LCD Adjustment.
2) The Automatic Adjustment Program executes the “1. Data
Setting during LCD/EVF Adj.” and “2. LCD Automatic Adj.”.
3) After that, the following screen is displayed during the execu-
tion of “3. V-COM Adj.”. Using the [Up]/[Down] button on the
screen, adjust so that the brightness of portions A and B on the
LCD panel is equal. After the adjustment, click the [End] but-
ton in the screen.
5) If the [End] button is clicked, “5. Reflective Mode White Bal-
ance Adj.” and “6. Sample Hold Phase Adj.” will be executed.
The following screen is displayed during the execution of “6.
Sample Hold Phase Adj.”. Using the [Up]/[Down] button on
the screen, adjust so that the 2nd portion A of the LCD screen
is Brightest. After the adjustment, click the [End] button in the
screen.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-32
4. EVF Adjustment 5. Touch Panel Adjustment
(HDR-SR7/SR7E/SR8/SR8E only) [Automatic Adjustment Program execution items and
[Automatic Adjustment Program execution items and sequence]
sequence] 1. Touch Panel Adj.
1. Data Setting during LCD/EVF Adj. 2. Release of Data Setting during LCD/EVF Adj.
2. EVF Automatic Adj.
(VCO Adj., Contrast Adj.) [Adjusting method]
3. White Balance Adj. 1) Click the [Start] button of the Touch Panel Adjustment.
4. Release of Data Setting during LCD/EVF Adj. 2) The Automatic Adjustment Program executes the “1. Touch
Panel Adj.”. The following message is displayed, and then
[Adjusting method] adjust the LCD screen in accordance with the instructions given
1) Click the [Start] button of the EVF Adjustment. on the screen. After the adjustment, click the [OK] button in
2) The Automatic Adjustment Program executes the “1. Data the message window.
Setting during LCD/EVF Adj.” and “2. EVF Automatic Adj.”.
3) After that, the following screen is displayed during the execu-
tion of “3. White Balance Adj.”. Check that the EVF screen is
not colored. If colored, using the [Up]/[Down] button on the
screen, adjust so that the EVF screen is not colored. After the
adjustment, click the [End] button in the screen.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-33
1-9. AUDIO SYSTEM ADJUSTMENTS
2 3
Fig. 6-1-23
2 [Preparation] button
Notes for adjustment or jigs used are displayed.
3 [Start] button
“Audio Adjustment” starts.
Table 6-1-6
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-34
3. AUDIO Adjustment [Adjusting method]
Note 1: AUDIO Adjustment is available only once after the power 1) Play back the adjustment sound source file on the PC.
is turned on. If the adjustment is retried, turn off the power 2) Set the speaker volume so that the adjustment signal sound is
and turn on again. heard to the extent of the loudness of talking voices.
3) Click the [Start] button of the AUDIO Adjustment.
[Automatic Adjustment Program execution items and 4) The Automatic Adjustment Program executes “1. Data Setting
sequence] during AUDIO Adj.”.
1. Data Setting during AUDIO Adj. 5) When “1. Data Setting during AUDIO Adj.” completed suc-
2. Internal 3ch microphone Adj. cessfully, and the items “2. Internal 3ch microphone Adj.” and
3. Release of Data Setting during Audio Adj. “3. Release of Data Setting during AUDIO Adj.” will be ex-
ecuted.
[Preparation] 6) Upon successful completion of all items of the AUDIO Ad-
Prepare an amplifier built-in speaker for PC and arrange it above justment, the following message is displayed. Click the [OK]
the internal 3ch microphone of the camcoder. button.
• Adjust the speaker position so that it is within ±3 cm from the
center of camcoder internal 3ch microphone at the height of 40
cm.
• The diaphragm of speaker position should be set face down to-
ward the internal 3ch microphone.
• The speaker may be held by hand if it is hard to secure.
In case of adjustment NG, reduce or increase the speaker volume,
PC and then retry adjustment.
If the Adjustment Program displays a message “Volume too loud”
Amplifier built-in or “Volume too low”, adjust the speaker volume following the
speaker for PC
message.
about 40 cm
Internal 3ch
microphone
Fig. 6-1-24
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-35
1-10. ERROR 3. Adjustment Time Out
In the case of an error during the execution of adjustment, the
Automatic Adjustment Program interrupts the processing at that
point, and displays an error message, and then terminates the pro-
gram execution there.
Fig. 6-1-26
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-36
1-10-2. Precautions When an Error Occurred LCD System Adjustment screen
The Automatic Adjustment Program sets the data for adjustment
before the adjustment starts. Accordingly, if the adjustment termi-
nates by an error, the data during the adjustment may be left in the
camera.
Note: With this data left in the camera, the camera will not oper-
ate normally.
Fig. 6-1-31
Fig. 6-1-29
Fig. 6-1-32
Fig. 6-1-30
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-37
6-2. SERVICE MODE 2. Operation
• Block change
2-1. APPLICATION FOR ADJUSTMENT (SeusEX) To change the block, click [Block] on the SeusEX screen and
The adjustment software (SeusEX) can change operational coeffi- enter the block to be changed. The block is displayed in hexa-
cients of signal processing, EVR data, etc. same as the adjustment decimal notation.
remote commander. The SeusEX performs two-way communica-
tion between PC and camcorder using the USB terminal. The two- • Page change
way communication result data can be written in the nonvolatile To change the page, click [Page] on the SeusEX screen and en-
memory. ter the page to be changed. The page is displayed in hexadeci-
mal notation.
1. Connection
1) Connect the HASP key to the USB terminal of the PC. • Address change
2) Connect the PC and camcorder with the USB cable. To change the address, click [Address] on the SeusEX screen
3) Start the SeusEX on the PC. and enter the address to be changed. The address is displayed in
4) Click [Connect] on the SeusEX screen. If the connection is hexadecimal notation.
normal, the SeusEX screen will be as shown in Fig. 6-2-1,
indicating the “connected” state. • Data change
Note: The SeusEX will go in “disconnect” state, if the To change the data, click [Set] on the SeusEX screen and enter
camcorder is turned off (for instance, by resetting the the data. The data is displayed in hexadecimal notation.
set). In such a case, click [Connect] on the SeusEX This operation does not write the data to the nonvolatile memory.
screen to restore the “connected” state.
• Data writing
To write the data to the EEPROM, click [Write] on the SeusEX
screen and enter the data value to be written.
To write the data to the flash memory, change the data value
using the [Set] on the SeusEX screen and then click [Save] to
save the data.
• Data reading
The data displayed on the SeusEX screen are the data values at
the time when the pages and addresses were set, and they are
not updated automatically. To check the data change, click [Read]
on the SeusEX screen and update the displayed data.
Fig. 6-2-1
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-38
2-2. SERVICE MODE 2. Switch Check
Click the [Switch Check] button on the SERVICE MODE screen,
1. Function of Each Button on Service Mode Screen and the “SWITCH CHECK” screen will appear.
Click the [SERVICE MODE] button on the Main Menu screen, and
the “SERVICE MODE” screen in Fig. 6-2-2 will appear.
2
7
3 8
Fig. 6-2-2
Using method:
1 [To Menu] button Click the [Start] button, and the switch check will start.
The Main Menu screen comes back. During execution of switch check, the pressed switch is displayed
in orange. Also, once the switch was pressed, its name characters
2 [Switch Check] button change to blue in color.
“SWITCH CHECK” screen appears.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-39
3. LED Check 4. Jack Check
Click the [LED Check] button on the SERVICE MODE screen, Click the [Jack Check] button on the SERVICE MODE screen,
and the “LED CHECK” screen will appear. and the “JACK CHECK” screen will appear.
Using method:
LED ON or OFF can be controlled with [LED ON] or [LED OFF]
button on the screen.
Using method:
Click the [Start] button, and the jack check will start.
During execution of jack check, the connected jack is displayed in
orange.
Note: The HDMI OUT jack is displayed in orange when it is con-
nected to a unit that supports HDMI.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-40
5. Lens Barrier Check 7. Record Data
Click the [Lens Barrier Check] button on the SERVICE MODE Click the [Record Data] button on the SERVICE MODE screen,
screen, and the “LENS BARRIER CHECK” screen will appear. and the “RECORD DATA” screen will appear.
Using method:
The lens barrier open or close can be controlled with [OPEN] or
[CLOSE] button on the screen.
6. G Sensor Check
Click the [G Sensor Check] button on the SERVICE MODE screen, The record data such as use record and self-diagnostic record are
and the “G SENSOR CHECK” screen will appear. displayed.
Using method:
Click the [Start] button, and the G sensor check will start.
During execution of G sensor check, the conditon of G sensor is
displayed.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-41
8. Shift Lens Check [Check 2 using method]
Use the “Shift Lens Check” when the following self diagnostic Use this menu when E:62:11 (Shift Lens Overheating (Pitch)) oc-
codes are displayed. curred.
• E:62:10 [Shift Lens Initializing Failure] Click the [Check 2 Start] button, and the shift lens will move in up
• E:62:11 [Shift Lens Overheating (Pitch)] and down directions. If the shift lens does not move, replace the
• E:62:12 [Shift Lens Overheating (Yaw)] lens block.
Click the [Shift Lens Check] button on the Service Mode screen, [Check 3 using method]
and the “SHIFT LENS CHECK” screen will appear. Use this menu when E:62:12 (Shift Lens Overheating (Yaw)) oc-
curred.
Click the [Check 3 Start] button, and the shift lens will move in left
and right directions. If the shift lens does not move, replace the
lens block.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-42
2-3. DATA BACKUP 1. Function of Each Button on Data Backup Screen
With the “DATA BACKUP”, the adjustment data in the camcorder Click the [DATA BACKUP] button on the Main Menu screen, and
can be backed up in the PC as a file. the “DATA BACKUP” screen in Fig. 6-2-3 will appear.
The adjustment data that can be backed up are as follows.
1
System Control Section:
1) Video System Adjustments
2) LCD/EVF System Adjustments
3) Audio System Adjustments
2 2
Camera Control Section:
1) Camera System Adjustments
3 3
Fig. 6-2-3
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-43
FOR CAMERA COLOR REPRODUCTION ADJUSTMENT
R-Y
R MG
YE
B-Y
G CY
✄ HDR-SR5/SR5C
R-Y
R MG
YE
B-Y
CY
G
✄
HDR-SR5/SR5C
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-44
FOR CAMERA COLOR REPRODUCTION ADJUSTMENT
R-Y
R MG
YE
B-Y
G CY
✄ HDR-SR5E
R-Y
MG
R
YE
B-Y
CY
G
✄
HDR-SR5E
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-45
FOR CAMERA COLOR REPRODUCTION ADJUSTMENT
R-Y
R MG
YE
B-Y
G CY
✄ HDR-SR7/SR8
R-Y
R MG
YE
B-Y
B
CY
G
✄
HDR-SR7/SR8
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-46
FOR CAMERA COLOR REPRODUCTION ADJUSTMENT
R-Y
MG
R
YE
B-Y
G CY
✄ HDR-SR7E/SR8E
R-Y
MG
R
YE
B-Y
B
CY
G
✄
HDR-SR7E/SR8E
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ
6-47E
Reverse 985220251.pdf
Revision History
S.M. Rev.
Ver. Date History Contents
issued
1.0 2007.05 Official Release — —
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_ADJ