Documente Academic
Documente Profesional
Documente Cultură
All miniatures shown in this document are from the BONES product line by REAPER MINIATURES
(www.reapermini.com)
PRODUCERS
Aeludor • Simon Cheng • Christopher Gay • Frank Laycock
A.A. Mudge • Kevin Roust • Joseph E. Walker • Brom M. Waydick
Permission granted to print this document and all related model files for personal use.
HALLS OF THE MOUNTAIN KING
Before proceeding with this document, make sure you have read the beginners
guide to card modeling included with this model set. Also, review all of your layer
options before printing, there are several ways you can design your tower!
PILLARS
1: Cut and score the base pieces and edge with a mark- 2: Cut, score and edge the main pillar.
er before proceeding.
3: Cut, score and edge the top cap. 4: Glue the top cap to the interior upper edge of the
main pillar.
HALLS OF THE MOUNTAIN KING
5: Glue the main pillar along the side seam to form a 6: Apply glue to the three remaining inside edges of
square cross-section and allow to dry. the top, fold the top cap in, and turn upside against a
flat surface to ensure an even alignment with the side
edge top.
7: Glue only ONE tab of the base section as shown and 8: Finish the three remaining tabs. This base can now
allow to fully dry before proceeding. It helps to use a be glued to a floor tile, and the pillar inserted and re-
ruler to apply pressure right at the corner while drying moved for storage or transport (do not glue the pillar
for a few seconds. unless you are building a permanent display.)
HALLS OF THE MOUNTAIN KING
ITEMS
1. Cut and score the gong pieces. 2: Fold and glue in half. Allow to fully dry before pro-
ceeding.
3: Cut away the unused white areas. 4: Glue the three pieces together as shown above.
HALLS OF THE MOUNTAIN KING
5: Cut, score and edge the throne pieces. 6: Fold the sides and rear flaps and glue.
7: Glue the seat section. 8: Cut away the excess white areas.
HALLS OF THE MOUNTAIN KING
9: Glue the rear of the seat to the main chair piece. 10: Glue the sides and set aside to dry.
11: Cut, score and edge the dias pieces. 12: Glue the two pieces together along the rear edge
tab.
HALLS OF THE MOUNTAIN KING
13: Glue the two side tabs next, followed by the two 14: Finally glue the center tab last.
angled tabs.
15: The finished throne pieces. 16: Cut, score and edge the sarcophagus pieces.
HALLS OF THE MOUNTAIN KING
17: Glue the side tab of each corner piece and allow to 18: Glue the top and bottom flaps.
dry.
19: All four sides simple fold and glue in half as de- 20: Glue the four corner tabs of the top section and al-
picted above. low to fully dry before proceeding. Finish by gluing the
bottom flap into place.
HALLS OF THE MOUNTAIN KING
21: The finished subassemblies. 22: Glue a corner section to each end of the longer side
walls as shown.
23: Glue the shorter side walls as depicted above. 24: Finish by gluing the remaining ends.
HALLS OF THE MOUNTAIN KING
25: Glue the finished side walls to the base. 26: The finished sarcophagus.
27: Cut and score the fire pedestal pieces. 28: Assemble as shown.
HALLS OF THE MOUNTAIN KING
29: The banners simple fold and glue in half. Insert the
two slots together (glue is optional.)
HALLS OF THE MOUNTAIN KING
GIANT DOOR
1: Cut, score, yadda yadda yadda.... 2: Use your gray marker to color the inside face around
the door opening. This will make any misalignments of
the inner wall section far less noticeable.
3: Glue the two inner wall pieces together at the top. 4: Glue to the interior of an outer-wall section. We rec-
MAKE SURE YOU HAVE CUT THE SMALL SLOT ommend gluing the side of the inner wall that has the
OPENINGS FOR THE DOOR HINGES! slots for the doors. Start with the top center tab and
then proceed to glue the side tabs.
HALLS OF THE MOUNTAIN KING
5: Glue the upper cap piece to the front wall section. 6: Glue the side walls to the front wall section.
7: Glue the bottom caps in place. 8: Glue the opposite wall face to the top cap as depicted
above.
HALLS OF THE MOUNTAIN KING
9: Fold over and glue to the inner wall tabs first. 10: Now glue the exterior edges to the outer side wall
tabs.
11: Finish by gluing the bottom flaps. 12: Cut, score and edge the wall pillar pieces.
HALLS OF THE MOUNTAIN KING
13: Glue the long side seam first. Finish by gluing the 14: Glue to the white sections on each side of the door
top flap in place. opening.
15: Repeat for the opposite side. 16: The doors fold and glue in half.
HALLS OF THE MOUNTAIN KING
1: Cut, score and edge the three main pieces, glue the 2: Now glue the short front tab.
two side pieces together along the long rear tab.
HALLS OF THE MOUNTAIN KING
3: Glue the long sloped edge into place. 4: Glue one edge of the bottom flap and allow to dry.
3-D Wall
Connector Connector
E-Z Lock Bobby Pin/ Base Base
Cover Hair pin (Corner) (Center)
E-Z Lock
E-Z Lock Tile Support
HALLS OF THE MOUNTAIN KING
Use the cover pieces to hide the holes in your tile when Insert the E-Z LOCK pillar as shown above.
not in use. Remove covers where you need to use an
E-Z LOCK pillar (you only need one to anchor a large
section.) Most dungeon layouts only use 2-3 as that is
plenty to keep the layout bump proof.)
Add a wall section next to your pillar. Use standard 2” bobby-pins or hairpins to lock the
pieces together.
HALLS OF THE MOUNTAIN KING
Project Patrons
©2013 Fat Dragon Games. Halls of the Mountain King is a trademark of Fat Dragon Games. All rights reserved.
www.fatdragongames.com