Documente Academic
Documente Profesional
Documente Cultură
0014
Engineering Data Coding System Rev.: F
Date: 12.05.2017
Page 2 of 15
CONTENTS
Title Page
FOREWORD 4
1.0 Objective 5
2.0 Scope 5
3.0 Application 5
4.0 Definitions 6
7.0 PEPS Engineering Standard Drawings, Data Sheets & QP Addendums to Shell DEP 9
APPENDICES
FOREWORD
This standard has been revised to include Data Coding System for PEPS Engineering Standard Drawings,
Data Sheets and QP Addendums to Shell DEP’s under the custodianship of Engineering Services
Department.
Operatorship of Al-Rayyan Field and the associated Al-Morjan platform has been transferred from
Occidental Petroleum Qatar Ltd. (OPQL) to Qatar Petroleum effective from May 2017. Accordingly, the Data
Coding System of the Al-Morjan Production Facilities has been included in this standard and is detailed in
Appendix D. It should be noted that the original numbering system used by OPQL has remained
unchanged to enable complete transparency to existing and future Data.
This standard does not cover the document numbering system, data coding, for following QP developed
documents.
The issue of this revised standard Revision F (Refer to Document Change History page 3) supersedes Doc
Number ES.0.07.0013 Numbering of Corporate Engineering Standards.
The Custodian of this Standard is Manager, Engineering Design, Info & Standards, (PTD), Engineering
Services Department, who is responsible for the accuracy and quality of its contents and for its future
revisions, where these are required to reflect industry trends or changes to QP business practices.
Note that any changes to this Standard from its last revision are highlighted by a bold vertical bar to
the left of each area of change; additionally, users can refer to the change history log on page 3.
Where cross-references to other parts of this Standard are made, the referenced section number is shown
in brackets (). Other documents referenced by this Standard are listed in (5.0).
Engineering Standard ES.0.07.0014
Engineering Data Coding System Rev.: F
Date: 12.05.2017
Page 5 of 15
1.0 Objective
The objective of this Standard is provide a uniform system for identifying, numbering and file
naming of QP Engineering Data (See 2.0).
The characteristics of the coding system will enable engineering data across all QP engineering
departments and QP Plants/Assets to be coded in a parallel, transparent, consistent and efficient
manner. For exceptions, refer (2.0).
2.0 Scope
This Standard defines the engineering data coding system to be applied to the following
Engineering Data:
Engineering data types covered by this standard are further defined in section (12.0). The Standard
also defines the As-Built Category for all engineering data types. (See Appendix C)
* QP Refinery (Mesaieed) FEED Projects shall use this Standard unless directed otherwise.
3.0 Application
This Standard shall be followed by all QP Departments, its Contractors and Consultants while
developing the following engineering drawings/documents:
All engineering personnel working for, and on behalf of QP shall adhere to this Standard.
Strict compliance with this standard is required. Any exceptions or deviations from this Standard,
along with their merits and justification, shall be brought to the attention of the custodian (PTD) for
review, consideration and amendment as required by completing part 1 of form ES.0.08.0014.
Sample of this form is shown in Appendix E. The form is available on QP Intranet under
Engineering Services Department
Engineering Standard ES.0.07.0014
Engineering Data Coding System Rev.: F
Date: 12.05.2017
Page 6 of 15
4.0 Definitions
For the purpose of this Standard, the following definitions apply.
As-Built Data - Data that reflects the true status of the plant, platform or facility
at the date of the site verification as shown in the revision
description column.
Document - A data medium and the data recorded on/in it, which generally
has permanence and that can be read by man or machine.
Grass Root Project - Grass Root Project is the term used to identify a project that
involves the design of a completely new plant, building, or facility.
Sometimes referred to as Green Fields.
Master Engineering Record - QP’s unique master controlled record. It reflects the status of the
plant, platform or facility at the date of the As-built as shown in
the revision description column. It is used to create project
drawings for projects involving the design, modification and
upgrade of existing facilities.
* Note: ES.0.06.0015 will replace Document Number ES.D.10 in the next update. Reference still
applies.
In all instances, users of this Standard shall refer to the latest approved version of the above
standards. The latest approved versions are as posted on QP Intranet under Engineering Services
Department. For confirmation of the latest approved versions, users of this Standard may contact
QP PTD Help Desk Engineering Services Department on +974 4013 6633.
The above drawings are available from EIS (ProjectWise). For help in retrieval, users of this
Standard may contact QP PTD Help Desk Engineering Services Department on +974 4013 6633.
For details of Master Engineering Records Data Coding System for Al-Morjan Production Facilities,
refer to Appendix D.
All Projects involved in the design of completely new Facilities (Grass Root) shall use the Master
Engineering Record Coding System as defined in Fig. 1 below. The Master Engineering Record
Coding system may be applied to projects of existing locations at the discretion of this Standards
custodian (3.0) in agreement with the applicable QP Asset owner. For coding of Isometrics, refer to
section (9.0).
The example in Fig 1 above indicates a Civil Discipline produced Buried Line or Trench drawing
located at Mesaieed NGL/1 flare system.
The assignment of Master Engineering Record codes to existing data (when applied) is the
responsibility of applicable authority (see table 1 below).
QP Asset Authority
Mesaieed – All MIC facilities excluding the end user facilities IM (M)
Dukhan – All DCA infrastructure support facilities excluding the OE (D) Oil fields
IM (D)
facilities
ES – 02– 57 – 0001
ES – 02 – 14 - 0001
QPAD – 05 – 14 – 0001
PTD/2 Division, Standards & Assurance Engineering, manages PEPS Engineering Standards
Drawings, Data Sheets and QP Addendums to Shell DEP number allocation.
Engineering Standard ES.0.07.0014
Engineering Data Coding System Rev.: F
Date: 12.05.2017
Page 10 of 15
The example in Fig 2 above shows a Civil produced Buried Line or Trench drawing for project
1234. The exceptions to the coding system shown in Fig 2 above are Isometrics, which shall use
the applicable Line Numbers as the drawing number. Refer to Section (9.0).
Al-Morjan Production Facilities will utilise the above project data coding system by use of Project
Number Prefix (8.1) followed by the Al-Morjan Production Facilities Data Coding System as defined
in Appendix D.
The Project Number is the first four (4) digits (See Fig. 2) of the Project Engineering Data Coding
System. The appropriate QP project department or their Contractor/Consultant, in accordance with
this Standard, shall apply the remainder of the project data code. (See Fig 2 above).
The project numbers are issued by QP PTD Help Desk upon request from QP Project
Engineer/Manager using either:
Standard form [ES.0.08.0001]. The fillable form is available on QP Intranet under Engineering
Services Department “Forms”. (Soon to be discontinued)
Vendor Documents and Drawings (See 4.0 for definition) shall be numbered in accordance with the
relevant section (6.0) or (8.0) of this Standard with the addition of prefix letters ‘VEN’. The
applicable Main Contractor shall control and issue the assigned Vendor Document/Drawing
numbers to the vendor, consultant or contractor. The Vendor shall show this number on the
applicable data in a place that is easily identifiable by QP when not using QP Standard Drawing
Border.
Note: For ease of allocation of Vendor numbers, users of this Standard shall note that the Data
Code after the prefix ‘VEN’ may duplicate with the non Vendor Data Coding, as the prefix ‘VEN’ will
become an integral part of the Vendor Data Code.
Engineering Standard ES.0.07.0014
Engineering Data Coding System Rev.: F
Date: 12.05.2017
Page 11 of 15
To ease control of the Vendor Data it is recommended that a separate Vendor index be utilized
during the development of the project and included as a final deliverable.
It shall be noted that modification of Vendor Data during project execution is the sole responsibility
of the Vendor. QP, Contractors or Consultants shall not modify this data in anyway. Furthermore,
after delivery of Vendor Data to QP the data shall not be modified by QP while any Vendor warranty
period is still valid.
Demolition Drawings shall be numbered in accordance with the section (8.0) Fig 2 of this Standard
with the addition of prefix letters ‘DEM’.
Note: For ease of allocation of Demolition drawings numbers, QP users shall note that the Data
Code after the prefix ‘DEM’ may duplicate with the non demolition data, as the prefix ‘DEM’ will
become an integral part of the Data Code.
To ease control of the Demolition Drawings, it is recommended that a separate Demolition Drawing
index be utilized during the development of the project and included as a final deliverable.
The words “Demolition Drawing” shall be placed in the title block of all demolition drawings.
Al-Morjan Production Facilities will utilise the above demolition numbering using Prefix ‘DEM’
followed by the Al-Morjan Production Facilities Data Coding System as defined in Appendix D.
For Line numbering tag strings of different QP locations please refer to the following referenced
engineering standards.
An example of an Isometric drawing number of a Line Number with tag string 6” - 310 - OC -
0001 - 31101 - 4EN will be as shown in the following example:
The above example is for a project with project number 1234 and the above example is taken from
Engineering Standard ES.0.07.0020 as referenced above.
Al-Morjan Production Facilities will utilise Isometric numbering System as defined in Appendix D.
The corresponding file name of Isometrics will omit the pipe size and shall be suffixed with the
drawing Rev Number; as per above line number (9.0) for the drawing Rev. The file name will be as
follows:
1234-310-OC-0001-001-A
Location Code for Al-Morjan Production Facilities is AMPF (Refer to Appendix D).
Users of this Standard shall strictly follow the location codes as defined in Appendix A, B & D.
Should locations codes not be available for the Facility/Plant/Platform under the Project Scope then
contact QP PTD Help Desk Engineering Services Department on +974 4013 6633 for further
guidance.
Location codes for new plants (Grass Root/Green Field Projects) shall be agreed upon with the QP
Engineering Services Department and the applicable authority (See Section 6.0 Table 1) before
implementation. The appropriate QP project department or their Contractor/Consultant shall apply
the remainder of the code in accordance with this Standard.
For Location Codes ending in TY and GE or TYP and GEN, refer to Appendix A Note 2 and
Appendix B Note 3.
Discipline Codes for Al-Morjan Production Facilities DO NOT follow the discipline code as defined in
Table 2 below. For details of Discipline Codes for Al-Morjan Production Facilities, refer to Appendix
D.
Note that the discipline codes shown in Table 2 are based on the disciplines responsible for the
development of the applicable engineering data as described in Appendix C.
Engineering Standard ES.0.07.0014
Engineering Data Coding System Rev.: F
Date: 12.05.2017
Page 13 of 15
For Document Types and Drawing Subgroups for Al-Morjan Production Facilities refer to Appendix
D. For all Other Locations the Data Type / Sub Groups are defined in Appendix C.
The Sub Group will define the data type or the nature of the information. Sub Groups 01 to 49 cater
for non-drawing related data like manuals, schedules, spreadsheets, presentations, databases,
data sheets, procedures, specifications etc. Sub Groups 01 to 49 are standard for all disciplines.
Sub Groups 50 onwards cater exclusively for drawings. These Sub Groups are discipline specific.
(Refer Appendix C).
Note that the Data Type / Sub group descriptions shall be considered for making up the last line of
all Drawing Titles refer to ES.D.10 (ES.0.06.0015*) Engineering Standard for Draughting.
*Note: ES.0.06.0015 will replace Document Number ES.D.10 in the next update. Reference still
applies.
12.1 Data Type for Discipline Code 9 Buildings, Architectural and Building Services
Discipline code 9 as defined in this section does not relate to Discipline code 9 as defined in
Appendix D, which only relates to Al-Morjan Production Facilities.
Sub Groups 00 to 49 shall be used for non-drawing related data. However, the sub group (00 to 49)
shall be prefixed by the Discipline Modifier to identify the respective discipline as shown in Appendix
C. The Sub groups 50 to 99 are replaced with a Discipline Modifier followed by specific data code.
Refer to Appendix C.
Engineering Standard ES.0.07.0014
Engineering Data Coding System Rev.: F
Date: 12.05.2017
Page 14 of 15
The structure of the coding system for non-drawing related data as defined above is as per
example below:
The structure of the coding system for drawings as defined above (12.1) is as per example below:
Users of this Standard shall note the divisions of responsibility between General, Civil, Electrical,
Loss Prevention, Instrumentation, Mechanical, and Telecommunications sectors (detailed under
Discipline Codes 0 to 8 inclusive) and sectors listed under Buildings (Discipline Code 9).
Discipline codes 0 to 8 inclusive are used for Oil and Gas related Projects. Discipline Code 9 is
primarily allocated to standalone Buildings and Building Structures on a specific plot. Generally,
non-Oil and Gas related projects.
Generally, all work within the plot boundaries of the building (s) are to be submitted under Discipline
Code 9 and will be described in detail under the Project Scope of Services. All design drawings and
information up to the respective plot boundaries shall be submitted under Discipline Codes 0, 1, 2,
3, 4, 5 & 8.
Sequence numbers as defined in this section does not relate to Al-Morjan Production Facilities. For
sequence numbers related to Al-Morjan Production Facilities refer to Appendix D.
Sequence numbers are purely a continuation method of numbering data of the same type within the
same location, discipline, and Sub Group. Sequence numbers shall start at 0001 and rise in
increments of one (1) for each drawing set having the same location, discipline, and Sub Group.
For Engineering Data developed in spread sheet format or print report from a database i.e. use of
MS Access or MS Excel, then Sheet numbering format may be presented as in the following
example.
For details of what constitutes to Multi Sheet sets and their requirements refer to ES.D.10
(ES.0.06.0015*) Engineering Standard for Draughting.
Engineering Standard ES.0.07.0014
Engineering Data Coding System Rev.: F
Date: 12.05.2017
Page 15 of 15
* Note: ES.0.06.0015 will replace Document Number ES.D.10 in the next update. Reference still
applies.
Documents produced in a project shall have their pages numbered to reflect the total number of
pages contained within the document i.e. Page 1 of 23, Page 2 of 23 etc. the last being page 23 of
23 in this example.
The exception to the above is for Isometric files names, refer to (9.1).
The file name will use dashes (-) to separate each individual field. i.e. Project Number (if used) Area
Code - Discipline Code - Sub Group - Sequence Number - Sheet Number if applied - Revision
Indicator. See examples in Sections (15.1, 15.2).
All AutoCAD files names shall include the applicable sheet number as in the below examples:
Example: An AutoCAD drawing revision B coded: 1234-M1FS –1-52-0001 Sht. 001 Cont.
002 Rev B
MS Office Produced Data may include multiple sheets within a single file. In such cases, the sheet
number is not required to be included in the file name. Example file naming is as shown below.
MASTER DOCUMENT NUMBERING FORMAT MASTER DRAWING NUMBERING FORMAT PROJECT DOCUMENT NUMBERING FORMAT PROJECT DRAWING NUMBERING FORMAT
AMPF-D-DT-NNNN-SSS AMPF-D-SG-NNNN-SSS 1234-AMPF-D-DT-NNNN-SSS 1234-AMPF-D-SG-NNNN-SSS
Sheet Number Sheet Number Project Number (8.1) Sheet Number Project Number (8.1) Sheet Number
Location Code Sequential Number Location Code Sequential Number Location Code Sequential Number Location Code Sequential Number
Discipline Code Document Type Discipline Code Drawing Type Discipline Code Document Type Discipline Code Drawing Type
DOCUMENT NUMBER / DATA CODE DOCUMENT FILE NAME DRAWING NUMBER / DATA CODE DRAWING FILE NAME DOCUMENT NUMBER / DATA CODE DOCUMENT FILE NAME DRAWING NUMBER / DATA CODE DRAWING FILE NAME
AMPF-0-CA-0001 Sht. 001 Cont. 002 Rev. B AMPF-0-CA-0001-001-B AMPF-1-02-1050 Sht. 001 Cont. 002 Rev. B AMPF-1-02-1050-001-B 1234-AMPF-0-CA-0001 Sht. 001 Cont. 002 Rev. B 1234-AMPF-0-CA-0001-001-B 1234-AMPF-1-02-1050 Sht. 001 Cont. 002 Rev. B 1234-AMPF-1-02-1050-001-B
AMPF-7-OM-0001 Sht. 001 Cont. 002 Rev. B AMPF-7-OM-0001-001-B AMPF-7-02-9050 Sht. 001 Cont. 002 Rev. B AMPF-7-02-9050-001-B 1234-AMPF-7-OM-0001 Sht. 001 Cont. 002 Rev. B 1234-AMPF-7-OM-0001-001-B 1234-AMPF-7-02-9050 Sht. 001 Cont. 002 Rev. B 1234-AMPF-7-02-9050-001-B
DEM-AMPF-1-11-1100 Sht. 001 Cont. 002 Rev. B DEM-AMPF-1-11-1100-001-B DEM-1234-AMPF-1-11-1100 Sht. 001 Cont. 002 Rev. B DEM-1234-AMPF-1-11-1100-001-B
Location Code Drawing Type, SG (Continuation) Drawing Type, SG (Continuation) Sequential Number Breakdown, NNNN (Continuation) Sequential Number Breakdown, NNNN (Continuation)
Location Code Description Drawing Type Description Drawing Type Description Document Type/ Document Type/
Discipline Discipline Code Description Sequential Range Discipline Discipline Code Description Sequential Range
AMPF Al-Morjan Production Facilities 18 Equipment Schedule 91 Hook-Up Drawing Type Drawing Type
- - 19 Line List 92 Hardware (Thermowells, etc.) Drawing Summary Sheet 01 6000 - 6005 Approach Drawing 39 2650 - 2699
20 Power Distribution 93 Bill of Materials Block Diagram 53 6006 - 6009 Crossing Detail 39 2700 - 2749
21 Details 94 Mechanical Drawing Electrical 4 Schedule 67 / 68 6010 - 6019 Riser Isometric and Tie-In Spool 39 2750 - 2799
Subsea 6
Discipline Code, D 22 Panel Terminal Arrangement 95 Miscellaneous Routing Drawing 76 6020 - 6049 Miscellaneous Detail 2800- 2849
Discipline Code Description 23 Junction Box Terminal Arrangement 96 Network Activity Flow Chart Location Plan / Layout 11 / 12 6050 - 6099 BOM 93 2850 - 2899
0 Process 24 Instrument Mounting Detail 97 DCS Document (Refer Note) As applicable 2900 - 2999
1 Piping/Mechanical 25 Detector Mounting Detail 98 Vendor Records General Arrangement 02 6100 - 6299
2 Structural 26 Penetration Detail 99 Symbols and Legends Termination Diagram 57 6300 - 6499 Drawing Summary Sheet 01 9000 - 9049
3 Civil 27 Pipe Support General - - Single Line Diagram 54 6500 - 6519 General Arrangement Drawing 02 9050 - 9199
Vendor 7
4 Electrical 28 Detail Drawings General Schematic Diagram 59 6520 - 6599 Detail Drawing 21 9200 - 9399
5 Instrumentation 29 Earthing Details Interconnection Diagram 55 6600 - 6609 Document (Refer Note) As applicable 9400 - 9499
6 Survey Topographic/Subsea 30 HVAC Duct Support Sequential Number Breakdown, NNNN Spare - 6610 - 6619
7 Equipment / Vendor Document 31 Escape Routes Document Type/ Spare - 6620 - 6629 Drawing Summary Sheet 01 9500 - 9549
Discipline Discipline Code Description Sequential Range
8 General (Covers Multi-Discipline) Admin / Management 32 Hazardous Area Drawing Drawing Type Spare - 6630 - 6699 Miscellaneous Drawing 95 9550 - 9649
Electrical 4 General 8
9 Telecommunication 33 Miscellaneous Steel Works Drawing Summary Sheet 01 0001 - 0009 Load List 09 6700 - 6799 BOM 93 9650 - 9699
34 Support Pipe / Rack / Vessel / Skid PFD 08 - Functional Logic Diagram 61 6800 - 6819 Document (Refer Note) As applicable 9700 - 9999
Document Type Description 37 Legs Concrete Destruct P&ID 06 0110 - 0200 Label 21 6930 - 6949 Block Diagram 53 4006 - 4009
BD Basis of Design 38 Installation And Rigging Line List 19 0101 - 0109 Mounting Detail 24 6950 - 6959 Schedule 67 / 71 / 72 4010 - 4019
CA Calculation 39 Subsea - Support Skids Pipeline Document (Refer Note) As applicable 0500 - 0999 Miscellaneous 95 6960 - 6969 Routing Drawing 76 / 77 4020 - 4049
CD Conceptual Design Report 40 Alarm and Trip Schedule Document (Refer Note) As applicable 6970 - 6999 Location Plan / Layout 11 / 14 / 17 4050 - 4099
CP Commissioning Procedure 41 Caisson / Riser / J-Tube Drawing Summary Sheet 01 1000 - 1049 General Arrangement 02 4100 - 4299
DD Detailed Design 42 Temporary Work Plot Plan 02 1050 - 1099 Drawing Summary Sheet 01 5000 - 5005 Termination Diagram 57 4300 - 4499
Piping - Plot Plans 1
DS Data Sheet 43 Dive Package Equipment Layout 11 1100 - 1149 Block Diagram 53 5006 - 5009 Single Line Diagram 54 4500 - 4519
EP Execution Plan 44 Handrail/ Walkway/ Grating Document (Refer Note) As applicable 1150 - 1199 Schedule 40 / 67 / 71 / 72 5010 - 5019 Schematic Diagram 59 4520 - 4599
HZ Hazop Report 45 System Isometric Routing Drawing 76 / 77 5020 - 5049 Interconnection Diagram 55 4600 - 4609
MR Material Requisition 46 Stress Isometric Drawing Summary Sheet 01 1200 - 1249 Location Plan / Layout 11 / 14 / 17 5050 - 5099 Telecom 9 Spare - 4610 - 4619
MS Method Statement / Miscellaneous Document 47 Hydrotest Isometric HVAC General Arrangement 02 1250 - 1299 General Arrangement 02 5100 - 5299 Spare - 4620 - 4629
OM Operating Manual 48 Piping Isometric Piping - HVAC 1 HVAC Detail Drawing 28 1300 - 1349 Termination Diagram 57 5300 - 5499 Cause and Effect Drawing 87 4630 - 4699
OP Operations Manual 49 Destruct Isometric BOM 93 1350 - 1399 Single Line Diagram 54 5500 - 5519 Loop Diagram 58 4700 - 4799
OS Offshore Survey 50 Flowline Isometric Document (Refer Note) As applicable 1400 - 1499 Schematic Diagram 59 5520 - 5599 Logic Diagram 61 4800 - 4819
PH Philosophy Document 51 Tie-In Isometric Interconnection Diagram 55 5600 - 5609 Hook-Up Diagram 91 4820 - 4899
PR Procedure 52 Vessel Trim Isometric Drawing Summary Sheet 01 2000 - 2029 Fire and Gas 5 Spare - 5610 - 5619 BOM 93 4900 - 4929
PS PSSR 53 Block Diagram Mechanical General Arrangement 02 2030 - 2149 Spare - 5620 - 5629 Label 21 4930 - 4949
Piping - Mechanical 1
QP Quality Plan 54 Single Line Diagram Mechanical Detail Drawing 28 2150 - 2299 Cause and Effect Drawing 87 5630 - 5699 Mounting Detail 24 4950 - 4959
RE Request for Quotation 55 Interconnection Diagram Document (Refer Note) As applicable 2300 - 2499 Loop Diagram 58 5700 - 5799 Miscellaneous 95 4960 - 4969
RM PRM Manual 56 Wiring Diagram Logic Diagram 61 5800 - 5819 Document (Refer Note) As applicable 4970 - 4999
RP General Technical Report 57 Termination Diagram Drawing Summary Sheet 01 3000 - 3019 Hook-Up Diagram 91 5820 - 5899
SA Safety Assessment 58 Loop Diagram Piping General Arrangement 02 3020 - 3099 BOM 93 5900 - 5929
SP Specification 59 Schematic Diagram Construct Isometric 48 3100 - 3299 Label 21 5930 - 5949 NOTE:
SR Statement of Requirement 60 Hydraulic Isometric Continuation Sheet Numbers to be used for ISO with Mounting Detail 24 5950 - 5959 1. For Documents, Contractors to start with Sequential Number Breakdown as stated in here and QP
- - In-house records to start with Sequential Number from 0001, 0002, …
ST Study 61 Logic Diagram same Line Number Miscellaneous 95 5960 - 5969
TB Technical Bid Evaluation 62 Nozzle Schedule Destruct Isometric 49 3300 - 3399 Document (Refer Note) As applicable 5970 - 5999
TE Technical Enquiry Package 63 Tie-In Schedule Piping - General 1 Hydraulic / Stress / Sys Iso 45 / 46 / 47 3400 - 3499
TM Training Manual 64 Valve Schedule Tie-In Schedule 63 3500 - 3529 Drawing Summary Sheet 01 7000 - 7005
TN Technical Note 65 Pipe Support Schedule Valve Schedule 64 3530 - 3559 Block Diagram 53 7006 - 7009
TP Test Procedure 66 Electrical Protection Schedule BOM 93 3560 - 3599 Schedule 40 / 67 / 71 / 72 7010 - 7019
WP Workpack 67 Cable Schedule Tree Stack-Up 28 3600 - 3649 Routing Drawing 76,77 7020 - 7049
WS Workscope 68 Lighting and Small Power Schedule Detail Drawing 28 3650 - 3899 Location Plan / Layout 11 / 14 / 17 7050 - 7099
- - 69 Miscellaneous Schedule Document (Refer Note) As applicable 3900 - 3999 General Arrangement 02 7100 - 7299
71 Instrument Schedule Drawing Summary Sheet 01 8000 - 8019 Single Line Diagram 54 7500 - 7519
Drawing Type, SG 72 Junction Box Schedule Structural General Arrangement 02 8020 - 8150 Schematic Diagram 59 7520 - 7599
Drawing Type Description 73 Block Diagram Schedule Structural Detail Drawing 28 8151 - 8199 Interconnection Diagram 55 7600 - 7609
Structural 2
01 Summary Sheet 74 Input/Output Schedule BOM 93 8200 - 8299 02 / 55 / 57 / 59 / 70
Telemetry and Associated Drawing 7610 - 7619
02 General Arrangement 75 Detector Schedule Rigging and Installation 38 8300 - 8399 Instrumentation 5 / 74
03 Panel General Arrangement 76 Cable Routing Document (Refer Note) As applicable 8400 - 8499 05 / 53 / 55 / 59 / 67
DCS and Computer System 7620 - 7629
04 Pipine Support General Arrangement 77 Rack / Tray Routing / 70 / 74 / 95
05 EFD (P&ID) 78 Pipe Support Standard Drawing Summary Sheet 01 8500 - 8519 Cause and Effect Drawing 87 7630 - 7699
06 Destruct P&ID 79 Piping Special Pipe Support Schedule 65 8520 - 8539 Loop Diagram 58 7700 - 7799
07 F&ID 80 Safety Analysis Chart Pipe Supports 2 Pipe Support General Arrangement 04 8540 - 8549 Logic Diagram 61 7800 - 7819
08 PFD 81 Cathodic Protection Pipe Support Detail Drawing 27 8550 - 8689 Hook-Up Diagram 91 7820 - 7899
11 Equipment Layout 84 Radio Systems Schematic Drawing Summary Sheet 01 8700 - 8749 Mounting Detail 24 7950 - 7959
12 Emergency Small Power Layout 85 Material Specification Architectural 3 Architectural Drawing 02 8750 - 8899 Miscellaneous 95 7960 - 7969
13 Navigation Aids Layout 86 Weight Control Sheet Document (Refer Note) As applicable 8900 - 8999 Document (Refer Note) As applicable 7970 - 7999
15 Lighting & Maintenance Diagram 88 Load Shredding Logic Drawing Summary Sheet 01 1500 - 1599 Drawing Summary Sheet 01 2500 - 2549
16 Environmental Platform Map 89 Fixing and Fastening Hazardous Area 4 Hazardous Area Drawing 32 1600 - 1699 Subsea 6 Field Layout 02 2550 - 2599
17 Detector Layout 90 Transit Detail Document (Refer Note) As applicable 1701 - 1999 Alignment Sheet 39 2600 - 2649
Continued Above-Right Continued Above-Right Continued Above-Right
Engineering Standard ES.0.07.0014
Engineering Data Coding System Date: 05.04.2017
Appendix E
Page 01 of 01
EXAMPLE
ONLY