Documente Academic
Documente Profesional
Documente Cultură
SRI ANDRI
2018.09.2 2018.09.28
8 13:28:38 13:41:56
+07'00' +07'00'
Contract N. 870126
Classes , 05892.PIP.MEC.SDS rev.06 - Pipes and Piping Components for Plant Piping
Project Specifications and 220801DTST23000_EXDE03 - Piping Project Specification
(Piping Class). It summarizes the different types of piping materials used for the
Floating Unit Production Upgrade.
Document Verification
REVISION LIST
00 Issued for Review
01 Issued for Approval
HOLD RECORD
The requirement of PWHT shall refer to 20368.PIP.MEC.FUN Rev.01 or can be
01
exempted as per ASME B31.3 Latest Rev.
INDEX
1.0 INTRODUCTION
Merakes development is an important initiative for Eni that will contribute to regional
growth and consolidate leadership role in the offshore South Kutei basin.
The East Sepinggan Block (2,913 km2) is located offshore in the deep water area of the
Kutei Basin, East Kalimantan, Indonesia. The Kutei Basin is one of the main producing
basin of Indonesia with more than 45 Tcf gas and 4,000 MMbbls oil reserves discovered,
mostly in Miocene/Pliocene sands.
The block was included in the 1st Indonesian Bidding Round of 2012; it was awarded to
eni Indonesia on 20th July 2012, with working interest of 100%. The license type is a
Production Sharing Contract (PSC), with a six year exploration period (3+3 years).
Currently Pertamina has farmed in with a 15% quote.
East Sepinggan is adjoining the Muara Bakau & Makassar Strait PSC. In Muara Bakau eni
discovered Jangkrik and Jangkrik NE. In Makassar Strait PSC Chevron has Maha-
Gendalo4 discovery (Mean OGIP ~580 Bcf).
This document is property of Eni East Sepinggan Ltd
It shall neither be shown to Third Parties not used for purposes other than those for which it has been sent.
Revision Index Sheet of
220810DTST24002 Sheets
Rev Validity
Number Status
6 of 14
Eni East Sepinggan,Ltd PIPING PROJECT
SPECIFICATION 01 EX-DE
(PIPING CLASS)
Merakes field is a dry gas discovery (very low CGR). The discovery is in around 1400 m
water depth. Merakes is located South in respect to Eni-operated Jangkrik field with a
linear distance of 35 km. Linear distance to shore instead is around 100 km.
Eni Indonesia drilled the Merakes-1 exploration well with success and successfully drilled
and tested also Merakes 2, the first appraisal well of the Merakes discovery.
The proximity of Merakes 2 discovery to the Jangkrik field will allow to maximizing the
synergies with existing nearby infrastructures as well as to reduce costs and time of the
execution of the future subsea development it confirms the success of Eni the “near field”
exploration and appraisal strategy.
The Merakes development is based on a 5-well submarine tie-back to the Jangrik FPU.
The production of Merakes will take place with 5 submarine wells (Merakes-3, Merakes-4,
Merakes-5, Merakes-6, Merakes-7) for which a phasing is planned and the rump-up will
follow the depletion of Jangkrik Main and Jangkrik North East.
The current architecture will allow an early start-up with 2 wells (XT available from the
JKK project) and a rigid pipeline or possibly with 3 or 4 wells by means of both pipelines..
The submarine wells of Merakes will be connected to the FPU by means of a double
production line, each with its own SSIV located at the base of flexible riser, commanded
by a common umbilical. A 6-slot and double-header submarine manifold will be used to
collect the production from 5 wells in Main Lobe and will allow the sorting of production
on the two production pipelines in order to manage any pressure differences between the
wells. The manifold will be controlled.
The double production line is recommended for flexibility: at high flow rates, both lines
will be used, while at the minimum turn-down, only one line will be in production. The
two-line configuration will solve (or mitigate) both the problem of the accumulation of
liquid at minimum sag and the problem of velocity at maximum flow.
The manifold will have a pigging loop that will close the Loop with FPU for intelligent
pigging.
The submarine control of the field will be provided by a electro-hydraulic umbilical.
Merakes topside system shall be designed to allow the tie-in of future developments, at a
maximum distance of 50km from Merakes and with a number of subsea equipment
similar to Merakes project.
It is important to highlight that the FPU is owned by a different JV (Muara Bakau),
therefore it is of primary importance to put in place a methodology on the FPU to allow
allocation from Jangkrik and Merakes.
This document is property of Eni East Sepinggan Ltd
It shall neither be shown to Third Parties not used for purposes other than those for which it has been sent.
Revision Index Sheet of
220810DTST24002 Sheets
Rev Validity
Number Status
7 of 14
Eni East Sepinggan,Ltd PIPING PROJECT
SPECIFICATION 01 EX-DE
(PIPING CLASS)
This document defines the minimum material requirements of pipes, fittings, flanges, stud
bolts & nuts, gaskets, valves and etc for FPU upgrade. This specification can also be used for
the piping materials within vendor supplied packages. This piping class shall be read in
conjuction with doc 06732.PIP.MEC.SDS Rev.16 Piping Classes and
220801DTST23000_EXDE03 Piping Project Specification (Piping Class). Piping Class which not
listed in this piping project specification shall be addressed to doc 220801DTST23000_EXDE03
Piping Project Specification (Piping Class). Piping components which not listed in this project
specification shall be addressed to doc 220810DTGA24006 Piping Special Item Data Sheets.
Any conflict of the present’s document with any other project requirement or referenced
document shall be highlighted by the SUPPLIER at Bid Stage and clarified before placement of
the Purchase Order by the CONTRACTOR to the SUPPLIER.
2.1 Definition
COMPANY Eni East Sepinggan
CONTRACTOR PT SAIPEM Indonesia
PROJECT FLOATING PRODUCTION UNIT UPGRADE
2.2 Abbreviations
API American Petroleum Institute
ASME American Society of Mechanical Engineers
ASTM American Society of Testing and Materials
BW Butt Weld
CFC Compact Flange Connection
DN Nominal Diameter
FB Full Bore
FPU Floating Production Unit
HDG Hot Dip Galvinizing
ISO International Organization for Standardization
NDT Non Destructive Testing
NPS Nominal Pipe Size
NPT Nominal Pipe Thread
P&ID Process and Instrumentation Diagram
RB Reduce Bore
RF Raised Face
RJ Ring Joint
SMLS Seamless
SW Socket Weld
WLDD Welded
API Standards
5L Specification for Line Pipe
Specification for Pipeline Valves (Gate, plug, Ball &
API 6D Check valve)
ASTM (American Standard Testing Material)
Standard Specification for Carbon Steel Forgings for
ASTM A105 Piping Applications
Standard Specification for Seamless Carbon Steel
ASTM A106 Pipe for High Temperature Service
ASTM A153 Zinc Coating (Hot Dip) on Iron and Steel Hardware
Standard Specification for Forged and Rolled Alloy
Steel Pipe Flanges, Forged Fittings, and Parts for
ASTM A182 High Temperature Service
Standard Specification for Alloy Steel and Stainless
ASTM A193 Steel Bolting Materials for High Temperature Service
Standard Specification for Carbon and Alloy Steel
Nuts for Bolts for High Pressure High Temperature
ASTM A194 Service
Standard Specification for Steel Casting, Carbon,
Suitable for Fusion Welding, for High-Temperature
ASTM A216 Service
Standard Specification for Piping Fittings of Wrought
ASTM A234 Carbon Steel and Alloy
Standard Specification for Alloy/Steel Bolting
ASTM A320 Materials for Low-Temperature Service
Standard Specification for Carbon and Low-Alloy
Steel Forgings, Requiring Notch Toughness Testing
ASTM A350 for Piping Components
Standard Specification for Steel Castings, Ferritic
and Martensitic, for Pressure - Containing Parts,
ASTM A352 Suitable for Low-Temperature Service
Specification for Electric Fusion Welded for Steel Pipe
ASTM A672 for High Pressure service at Moderate Temperature
ASTM A694 Carbon Steel High Strength Forgings
Standard specification for Wrought High-Strength
ASTM A860 Low Alloy Steel Butt Welding Fittings
ISO (International Organization for Standardization)
Petroleum and natural gas industries -- Compact
ISO 27509 flanged connections with IX seal ring
MSS (Manufacturers’ Standardization Society)
Integrally reinforced forged branch outlet fittings-
MSS SP-97 Socket welding, Threaded and Butt welding ends.
NORSOK
NORSOK-L-005 Compact Flanged Connection
RATING
SEQUENCE
NUMBER
48 CS
The second character indicates the pressure class (rating) of the piping class shown below.
RATING ASME
CHAR
B16.5
A 150
B 300
C 600
D 900
E 1500
F 2500
For carbon steel Project Piping Class with rating 1500# and above the maximum corrosion
allowances is 6 mm.
• In this Project Piping Class with flange rating #2500 the maximum nominal diameter is
limited to 24”. For size 14” and above rating #2500 shall use compact flange
connection ISO 27509.
• Lifting padeye shall be provided for compact flange.
• Flange jackscrew shall be in accordance with para 8 doc 220801DTST23000_EXDE03.
Flange spreader can be used to subtitute flange jackscrew.
• Positive Material Identification shall be in accordance with doc
220810DXEZ28108_EXDE00.
• Line classification for this project piping class shall refer to 20367.PIP.MEC.SDS Rev. 04
Table 1 Para 2.2.
• If line subject to vacuum condition, pipe shall be calculated as per ASME VIII Sec I Part
UG-28.
• The dimension of spectacle blind, spade, and spacer shall be in accordance with ASME
B16.48. Corrosion allowance shall be considered for the thickness of spectacle blind,
spade and spacer.
• Where spade blinds are used, these shall be provided complete with a matching spacer
ring.
• Valves shall comply with doc 220810DTGA24004 and 220810DTGA24005.
DESIGN
CONDITION
O PRESSURE CA
PIPING END TEMP
SERVICE RATING (BAR) MATERIAL
CLASS CON C
(mm)
MAX MIN
22F WELL FLUID 2500 RJ -46 TO 431 422.2 0 DUPLEX
(HYDROCARBON) 100 SS
48C CRUDE OIL, WELL 600 RJ -29 TO 100.2 87.6 6 CARBON
FLUID 200 STEEL
(HYDROCARBON)
48F WELL FLUID, 2500 RJ / -20 TO 285 285 6 CARBON
MULTIPHASE GAS CFC 100 STEEL
(HYDROCARBON) with X65
IX
seal
ring
SCHEDULE No. - 40S 80S 80S 160 160 160 160 XXS - - -
MATERIAL ASTM A 790 UNS S31803 ASTM A928 UNS31803
MANUAL CONTROL
----
VDR738PRAU1- RJ VDR738PR5U1-RJ (WAFER)
CHECK
----
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
220810DTST24002
Revisions/Rev. 1
Sht of Compiled Date/Data
PIPING PROJECT SPECIFICATION
1 1 SAIPEM 28/09/2018
SERVICE: WELL FLUID (HYDROCARBON) ITEM CORR.ALLOWANCE
48C 6 mm
RATING & FACING
600# RJ
DESIGN CONDITION: T - °C -29÷38 50 100 200 --- --- --- --- --- --- --- --- --- CODES- Design: ASME B 31.3/B16.5/B16.47 serie A/B16.34
P - bar 102.1 100.2 93.2 87.6 --- --- --- --- --- --- --- --- ---
NOMINAL SIZE INCH - 1/2" 3/4" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 26" 28" 30" 32" 34" 36"
WALL THK. mm - --- --- 9.09 10.16 11.07 11.13 13.49 14.27 18.26 18.26 20.62 23.83 23.83 26.97 28.58 33.32 33.95 36.50 38.25 40.64 42.36 45.28
PIPES
SCHEDULE No. - --- --- XXS XXS XXS 160 160 120 120 100 -- 100 --- --- --- --- --- --- --- --- --- ---
MATERIAL ASTM A 106 Grade B SMLS - CVN test -29°C B31.3 ASTM A672 Grade C70 Cl.22 EFW-CVN test -29°C B31.3
MANUFACTURE SMLS WELDED
WELDING NECK ASTM A 105 - CVN test -29°C B31.3/600#-RJ (70)
FLANGES
----
VDR715ENAD5-
CHECK (31) RJ
VDR715PR5D1-RJ (Wafer-Dual Plate)
CHECK
Ritegno
---- VDR715PR6D6-RJ (Wafer-Tilting)
---- VB915PR7D2-RJ (APPLICABLE FOR 2")
SPECIAL USE
FOR INSTRUMENT VD935PR6V1-RJXNPTF ----
A105 - CVN
20 WLET RTEE STEE SWLT SWEEPOLETS
test -29°C
24 STEE WLET WELDOLETS B31.3
26 STEE TLET THREDOLETS
A105 - CVN
M 32 STEE OELW WELDOFLANGE test -29°C
O B31.3
D 34 STEE
.
M 36 STEE
E 1 1½ 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
C
. DN" BRANCH SIZE
T NOTES/Note : 60) All the piping components for which heat treatment is not a mandatory requirement as per ASTM A105 section 5.1 due to their
U
B 1) All carbon steel bolting on flanges, valves & "Y" strainers shall be zinc coated (hot-dip) pressure and rating shall be normalized (N). Supplementary requirement S2 of ASTM A105 shall apply and require Normalizing heat
. to ASTM A-153. treatment for those parts.
0
0 2) To be used where required by P&I drawings only. 63) Shall be in accordance with Sp. Item list doc. No. 220810DTEL24020 & Sp item data sheet
2 3) Threaded Ends and connections are allowed for instruments taps and test drain/vent only. doc. No. 220810DTGA24006
/
4 6) All Valves compatible with fluids which have methanol content > 5% 64) Heat treatment is required as per ASTM A105.
70) RTJ Flanges size 2" and above shall be equipped with jackscrews or flange spreader bar shall be provided.
S 20) Deleted 81) Weldoflange/Nipoflange may be used for instrument tapping for thermowell.
h
.
0 21) In case of additional requirement S (NACE/ISO), components for NACE service must be used
1
/ (see also 06732 PIP.MEC.SDS).
0 31) Corrosion allowance to be considered and verified also for Body Valves and "Y" Strainers.
1
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
220810DTST24002
Revisions 1
Sht of Compiled Date/Data
PIPING PROJECT SPECIFICATION
1 1 SAIPEM 28/09/2018
SERVICE: WELL FLUID, MULTIPHASE GAS (HYDROCARBON) ITEM CORR.ALLOWANCE
48F 6 mm
RATING & FACING
2500# RJ
DESIGN CONDITION: T - °C -20÷38 75 100 --- --- --- --- --- --- --- --- --- --- CODES- Design: ASME B 31.3/ASME VIII Div.2/ ISO-27509
P - bar 285.0 285.0 285.0 --- --- --- --- --- --- --- --- --- ---
NOMINAL SIZE INCH - 1/2" 3/4" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" --- --- --- --- --- ---
WALL THK mm - --- --- 10.00 11.00 12.00 15.24 17.12 21.95 27.00 32.00 37.00 39.50 44.00 48.50 53.50 63.00 --- --- --- --- --- ---
PIPES
SCHEDULE No. - --- --- --- --- --- XXS XXS XXS --- --- --- --- --- --- --- --- --- --- --- --- --- ---
MATERIAL ---- API 5L Gr.X65
MANUFACTURE ---- SMLS WELDED
WELDING NECK ---- A694 GR.F65/2500# RJ ASME B16.5
A694 GR.F65/2500# CFC ISO-
COMPACT WITH IX SEALRING ----
FLANGES
27509/NORSOK L-005
SOCKET WELD ` ----
THREADED ----
SLIP ON ----
LAP JOINT ----
A694 GR.F65/2500# CFC ISO-
BLIND ---- A694 GR.F65/2500# RJ ASME B16.5
27509/NORSOK L-005
GASKETS ---- 81 A 05 SEAL RING IX (9)
STUD BOLTS & NUTS A193 Gr.B7M / A194 Gr.2HM (1)
VB518PR6D1-
---- VB518PR1D8-RJ (2" to 12") or CFC (14" to 24") (R.B)
RJ (F.B)
---- VB518PR2D8-RJ (2" to 12") or CFC (14" to 24") (F.B) (2)
ON/OFF
VB518PR3D1-CFC OR
----
BW (R.B) (T.E) (2)
VB518PR4D1-CFC OR
BW (F.B) (T.E) (2)
VALVES(6)
---- VD318PR1D2-RJ
(31)
MANUAL CONTROL
----
VDR718PRAD
CHECK
---- VDR718PR5D1-RJ (Wafer -Dual Plate)
CHECK 3-RJ
Ritegno
---- VDR718PR6D1-RJ (Wafer -Tilting)
----
SPECIAL USE
FOR INSTRUMENT VD938PR6V1-
----
RJxNPTF
" Y "STRAINERS (63)
90°-45° ELBOWS ---- A860 WPHY65-SMLS (BW) A860 WPHY65-WLD (BW)
ECC.-CONC.REDUCT. ---- A860 WPHY65-SMLS (BW) A860 WPHY65-WLD (BW)
ELLIPT.CAPS ---- A860 WPHY65-SMLS (BW)
LJ STUB ENDS ---- ----
PIPE BENDS ---- ----
MITER ELBOWS ---- ----
S.W. FITTINGS ---- ---- COMPONENTS MAT.
THDD FITTINGS ---- ---- RED.FLG.S THDD./Filet. S.O./a Sovr. ----
---- ---- ----
NIPPLES
DESIGN
CONDITION
O PRESSURE
PIPING END TEMP CA
SERVICE RATING (BAR) MATERIAL
CLASS CON C (mm)
MAX MIN
08A COMPRESSED AIR, 150# RF -10 TO 19.6 16.9 0 CARBON
OPEN DRAIN, 120 STEEL
INSTRUMENT AIR, GALVANIZED
UTILITY AIR,
UTILITY NITROGEN,
ATMOSPHERIC VENT,
COMPRESSED AIR
(NON HYDROCARBON)
30A SERVICE WATER, RAW PN 16 FF -10 TO 16 16 0 COPPER
WATER (NON 75 NICKEL
HYDROCARBON)
41A COMPRESSED AIR, 150# RF -10 TO 19.6 13.8 1 CARBON
RAW GAS, UTILITY 200 STEEL
NITROGEN, VENT
ATMOSPHERIC,
SLUDGE
(HYDROCARBON &
NON HYDROCARBON)
42A BLOW DOWN, CRUDE 150# RF -10 TO 19.6 13.8 3 CARBON
OIL, CLOSED DRAIN, 200 STEEL
OPEN DRAIN, GLYCOL,
RAW GAS, TREATED
OIL
(HYDROCARBON &
NON HYDROCARBON)
42C CLOSED DRAIN, 600# RJ -10 TO 102.1 87.6 3 CARBON
GLYCOL, RAW GAS 200 STEEL
(HYDROCARBON &
NON HYDROCARBON)
42E CLOSED DRAIN, 1500# RJ -10 TO 255.3 219 3 CARBON
UTILITY NITROGEN, 200 STEEL
WELL FLUID
43A CRUDE OIL, CLOSED 150# RF -10 TO 19.6 13.8 6 CARBON
DRAIN, GLYCOL 200 STEEL
CLOSED DRAIN,
GLYCOL, PRODUCED
WATER, RAW GAS,
TREATED OIL
43B CRUDE OIL, CLOSED 300# RF -10 TO 51.1 43.8 6 CARBON
DRAIN 200 STEEL
43C CRUDE OIL, CLOSED 600# -10 TO 102.1 87.6 6 CARBON
DRAIN, WELL FLUID 200 STEEL
This document is property of Eni East Sepinggan Ltd
It shall neither be shown to Third Parties not used for purposes other than those for which it has been sent.
Revision Index Sheet of
220810DTST24002 Sheets
Rev Validity
Number Status
14 of 14
Eni East Sepinggan,Ltd PIPING PROJECT
SPECIFICATION 01 EX-DE
(PIPING CLASS)
Servizio: Sigla
08A Sovraspes. di Corr. 0 mm
UTILITY NITROGEN, ATMOSPHERIC VENT, COMPRESSED AIR
RATING & FACING
(NON HYDROCARBON) Serie e Faccia 150# RF 125Ra
DESIGN CONDITION: T - °C -10÷38 50 100 120 --- --- --- --- --- --- --- --- --- CODES- Design: ASME B 31.3/B16.5/B16.34
Condizioni di Progetto: P - bar 19.6 19.2 17.7 16.9 --- --- --- --- --- --- --- --- --- Norme-Progetto:
NOMINAL SIZE/Diametro nom. INCH - 1/2" 3/4" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 30" 36"
WALL THK./Spessore mm - 3.73 3.91 4.55 5.08 5.54 5.49 6.02 --- --- --- --- --- --- --- --- --- --- ---
PIPES
SCHEDULE/Schedula No. - 80 80 80 80 80 40 40 --- --- --- --- --- --- --- --- --- --- ---
MATERIAL/Materiale ASTM A106-B SMLS GALV.
MANUFACTURE/Costruzione SMLS (THDD & CPLD)
WELDING NECK/Sald. di Testa
LAP JOINT/Libere
GASKETS/Guarnizioni 32 C 28
STUD BOLTS & NUTS/Tiranti-Bulloni A 193 Gr.B7 / A 194 Gr.2H (ZINC COATED) (1) (2)
VB 511 AG 1C1(RB)-RF125Ra
ON/OFF VB 635 AG 6R1-NPT
VB 511 AG 2C1(FB) -RF125Ra
Intercettazione
VB 515 AG 5C1 - RF125 Ra ----
VD 435 AG 7R1 - NPT VD 311 AG A04 - RF 125 Ra
VALVES
MANUAL CONTROL
Regolaz. Man. ---- ----
VDR 711 AG 6C1 - RF 125 Ra
CHECK VDR 835 AG 3R1 - NPT
(Wafer-Tilting)
Ritegno
VDR 711 PR 1C6-RF 125 Ra
----
(Swing)
SPECIAL USE VB 513 AG 1C7- RF 125 Ra
FOR INSTRUMENT VD 935 PR 5R1- RF x NPT VD 933 PR 5R1-2"- RF x NPT
" Y "STRAINERS/Filtri a "Y" (63)
90°-45° ELBOWS/Curve 90°-45° ASTM A234 WPB - SMLS (THD)
ECC.-CONC.REDUCT./Rid.Conc.-Ecc. ----
ELLIPT.CAPS/Fondelli Bombati ----
LJ STUB ENDS/Collari Flg.Libere ----
PIPE BENDS/Curve da Tubo ----
MITER ELBOWS/Curve a Spicchi ----
S.W. FITTINGS/Raccorderia S.W. ---- COMPONENTS/Componenti MAT./Mat.
THDD FITTINGS/Raccorderia Fil. A 105 GALV./3000# NPT RED.FLG.S/FLG di Rid. THDD./Fil. S.O./a Sovr. A 105 GALV.
A 53 Gr.B SMLS GALV.
NIPPLES
NORMAL /Normali
Nippli
SWAGES/Di Riduzione A 53 Gr.B SMLS GALV. DRIP RINGS/Anelli di Drenaggio A 105 GALV.
THICKNESS/Spessori mm - 3.73 3.91 4.55 5.08 5.54 5.49 6.02 - SPECTACLE & SPACERS-BLINDS/Dischi a 8-Sezionatori A 105 GALV.
1/2 STSC REFERENCE SPECIFICATIONS/Specifiche di riferimento
3/4 STSC WELDING AND HEAT TREATMENT/ Saldature e Trattamenti Termici -----
1 STSC PIPING CLASS/ Classe Tubazione -----
1½ STSC WELDS EXAMINATION/ Controllo Saldature -----
2 STSC MATERIALS (if not otherw.stated)/ Materiali(se non div.indicato) ASTM STANDARDS
HEADER SIZE/Collettore
/ 36 SLET SOCKOLETS
4
1/2 3/4 1 1½ 2 3 4 6 8 10 12 14 16 18 20 24 30 36 NLET NIPOLETS THDD / Nipolets Filettate
S DN" BRANCH SIZE/Derivazione OELW WELDOFLANGE
h
. NOTES/Note : 62) For vessel connections with instrumentation, minimum size and rating are 2" and 300#.
0 1) All carbon steel bolting on flanges, valves & "Y" strainers shall be zinc coated (hot-dip) 63) Shall be in accordance with Sp. Item list doc. No. 220801DTEL20800 & Sp item data
1
to ASTM A-153 sheet doc. No. 220801DTGA23101
/
0 2) A 193 Gr.B7M / A 194 Gr.2HM (ZINC COATED) is acceptable
1 60) All the piping components for which heat treatment is not a mandatory requirement S2 of
ASTM A105 shall apply and require Normalizing heat treatment for those.
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
Il presente documento è RISERVATO ed è di proprietà di ENI E&P. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
220801DTST23000
Eni S.p.A. Revisions/Rev.
E&P Division PIPING PROJECT SPECIFICATION
Sht/Foglio of/di Compiled/Compilato Date/Data
1 1 STCJ
SERVICE: SERVICE WATER, RAW WATER (NON HYDROCARBON) ITEM CORR.ALLOWANCE
Servizio:
30A Sovraspes. di Corr. 0 mm
RATING & FACING
Serie e Faccia 16 bar(g) FF (16)
DESIGN CONDITION: T - °C -10÷38 75 --- --- --- --- --- --- --- --- --- --- --- CODES- Design: ASME B 31.3/B16.34
Condizioni di Progetto: P - bar 16 16 --- --- --- --- --- --- --- --- --- --- --- Norme-Progetto: EEMUA
NOMINAL SIZE/Diametro nom. INCH - 1/2" 3/4" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"
WALL THK./Spessore mm - 2.00 2.00 2.50 2.50 2.50 2.50 3.00 3.00 4.00 4.50 5.50 6.50 7.00 8.00 8.50 10.50
PIPES
EXTERNAL DIA./Dia.est. mm - 21.3 26.7 33.4 48.3 60.3 88.9 114.3 168.3 219.1 273.1 323.9 355.6 406.4 457.0 508.0 610.0
MATERIAL/Materiale Cu/Ni 90-10 ASTM UNS C70600 (EEMUA 144, 16 bar(g))
MANUFACTURE/Costruzione SMLS WLDD
INTEGRAL WN/Sald. di Testa ---- Cu/Ni 90-10 (EEMUA 145, 16 bar(g)) (16)
FLANGES
S 1) All carbon steel bolting on flanges, valves & "Y" strainers shall be zinc coated (hot-dip) 16) Facing selection shall be made time by time depending on components to join./
h to ASTM A-153 La scelta del tipo di faccia deve essere fatta di volta in volta in funzione del
.
componente da accoppiare.
0
1 6) For integral flanges: ASTM F 468 UNS C71000 / ASTM F 467 UNS C71000./Per flange 17) Support for Cu/Ni pipework shall be lined with a soft packing strip or pad, free of
/ integrali: ASTM F 468 UNS C71000 / ASTM F 467 UNS C71000. ammoniacal compounds, to prevent chafing and undue stressing and provide insulation
0
1 8) Gaskets are not required for butterfly valves installation./Per l'installazione delle between ferrous and Cu/Ni component parts./I supporti per le tubazioni in Cu/Ni devono
valvole a farfalla non sono richieste guarnizioni. essere rivestiti con materiale morbido, esente da composti ammoniacali, al fine di
15) Engineer shall select the fittings between type "X" (capillary brazing fittings) and prevenire scalfitture e/o sollecitazioni indesiderate e isolare le parti ferrose da quelle
type "Y" (fusion socket weld fittings)./La scelta tra il raccordo tipo "X" (saldo- in Cu/Ni.
63) Shall be in accordance with Sp. Item list doc. No. 220801DTEL20800 & Sp item data sheet
doc. No. 220801DTGA23101
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
Il presente documento è RISERVATO ed è di proprietà di ENI E&P. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
220801DTST23000
Eni S.p.A. Revisions/Rev.
E&P Division PIPING PROJECT SPECIFICATION
Sht/Foglio of/di Compiled/Compilato Date/Data
1 1 STCJ
SERVICE: COMPRESSED AIR, RAW GAS, UTILITY NITROGEN, VENT ITEM CORR.ALLOWANCE
Servizio: Sigla
41A Sovraspes. di Corr. 1 mm
ATMOSPHERIC, SLUDGE
RATING & FACING
(HYDROCARBON & NON HYDROCARBON) Serie e Faccia 150# RF 125Ra
DESIGN CONDITION: T - °C -10÷38 50 100 150 200 --- --- --- --- --- --- --- --- CODES- Design: ASME B 31.3/B16.5/B16.34
Condizioni di Progetto: P - bar 19.6 19.2 17.7 15.8 13.8 --- --- --- --- --- --- --- --- Norme-Progetto:
NOMINAL SIZE/Diametro nom. INCH - 1/2" 3/4" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 26" 28" 30" 32" 34" 36"
WALL THK./Spessore mm - 3.73 3.91 4.55 5.08 5.54 5.49 6.02 7.11 8.18 9.27 9.52 9.52 9.52 9.52 9.52 9.52 9.52 9.52 12.70 12.70 12.70 12.70
PIPES
SCHEDULE/Schedula No. - 80 80 80 80 80 40 40 40 40 STD STD STD STD STD STD STD STD STD 20 20 20 20
MATERIAL/Materiale ASTM A106 Gr. B ASTM A672 Gr. C70 Cl. 22
MANUFACTURE/Costruzione SMLS WLDD
WELDING NECK/Sald. di Testa A105/600#-RF125Ra A105/150#-RF125Ra
FLANGES
MANUAL CONTROL
Regolaz. Man.
(31) VDR 735 AG AR2 -RF125Ra VDR 711 AG 6C1 - RF 125 Ra (Wafer-Tilting)
CHECK
Ritegno
VDR 711 AG 5C4-RF 125 Ra (Wafer -Dual Plate)
---- VDR 711 PR 9C1-RF 125 Ra (Non Slam)
SPECIAL USE VB 513 AG 1C7-RF125Ra-2"
FOR INSTRUMENT
VD 935 PR 5R1-RF x NPT VD 933 PR 5R1 - RF x NPT-2"
" Y "STRAINERS/Filtri a "Y" (63)
90°-45° ELBOWS/Curve 90°-45° A234 Gr.WPB - SMLS (BW) A234 Gr.WPB - WLDD (BW)
ECC.-CONC.REDUCT./Rid.Conc.-Ecc. A234 Gr.WPB - SMLS (BW) A234 Gr.WPB - WLDD (BW)
ELLIPT.CAPS/Fondelli Bombati A 234 Gr.WPB - SMLS (BW)
LJ STUB ENDS/Collari Flg.Libere ----
PIPE BENDS/Curve da Tubo ---- ----
MITER ELBOWS/Curve a Spicchi ---- ----
S.W. FITTINGS/Raccorderia S.W. ---- ---- COMPONENTS/Componenti MAT./Mat.
THDD FITTINGS/Raccorderia Fil. A105 /3000# NPT(3) ---- RED.FLG.S/FLG di Rid. THDD./Filet. S.O./a Sovr. A105 (3)
ASTM A106 Gr.B SMLS (3) ---- (63)
NIPPLES
SWAGES/Di Riduzione ASTM A106 Gr.B SMLS (3) ---- DRIP RINGS/Anelli di Drenaggio A105
THICKNESS/Spessori mm - 3.73 3.91 4.55 5.08 5.54 - - - SPECTACLE & SPACERS-BLINDS/Dischi a 8-Sezionatori A105
1/2 STEE REFERENCE SPECIFICATIONS/Specifiche di riferimento
3/4 STEE WELDING AND HEAT TREATMENT/Saldature e Trattamenti Termici 20368.PIP.MEC.FUN
1 RTEE STEE PIPING CLASS/Classe Tubazione 20367.PIP.MEC.FUN
1½ STEE WELDS EXAMINATION/Controllo Saldature 20377.PIP.MEC.FUN
2 STEE MATERIALS (if not otherw.stated)/Materiali(se non div.indicato) ASTM STANDARDS
3 STEE PIPING COMPONENTS/Componenti per tubazioni 05892.PIP.MEC.FUN
4 STEE
HEADER SIZE/Collettore
E
24 STEE WLET WELDOLETS A105
C
. 26 STEE TLET THREDOLETS (3) A105
T
U
28 STEE SLET SOCKOLETS
B 30 STEE
.
0 32 STEE
0 34 STEE
2
/ 36 STEE
Servizio: Sigla
42A Sovraspes. di Corr. 3 mm
GLYCOL, RAW GAS, TREATED OIL
RATING & FACING
(HYDROCARBON & NON HYDROCARBON) Serie e Faccia 150# RF 125Ra
DESIGN CONDITION: T - °C -10÷38 50 100 150 200 --- --- --- --- --- --- --- --- CODES- Design: ASME B 31.3/B16.5/B16.34
Condizioni di Progetto: P - bar 19.6 19.2 17.7 15.8 13.8 --- --- --- --- --- --- --- --- Norme-Progetto:
NOMINAL SIZE/Diametro nom. INCH - 1/2" 3/4" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 26" 28" 30" 32" 34" 36"
WALL THK./Spessore mm - 7.47 5.56 6.35 7.14 8.74 7.62 6.02 7.11 8.18 9.27 9.52 9.52 9.52 9.52 9.52 9.52 9.52 9.52 9.52 9.52 9.52 9.52
PIPES
SCHEDULE/Schedula No. - XXS 160 160 160 160 80 40 40 40 STD STD STD STD STD STD STD STD STD 20 20 20 20
MATERIAL/Materiale ASTM A106 Gr. B ASTM A672 Gr. C70 Cl. 22
MANUFACTURE/Costruzione SMLS WLDD
WELDING NECK/Sald. di Testa A105/600#-RF125Ra A105/150#-RF125Ra
FLANGES
NORMAL /Normali ASTM A106 Gr.B SMLS (3) ---- TEMP. STRAINERS/Filtri Temporanei
Nippli
SWAGES/Di Riduzione ASTM A106 Gr.B SMLS (3) ---- DRIP RINGS/Anelli di Drenaggio A105
THICKNESS/Spessori mm - 7.47 5.56 6.35 7.14 8.74 - - - SPECTACLE & SPACERS-BLINDS/Dischi a 8-Sezionatori A105
1/2 STEE REFERENCE SPECIFICATIONS/Specifiche di riferimento
3/4 STEE WELDING AND HEAT TREATMENT/Saldature e Trattamenti Termici 20368.PIP.MEC.FUN
1 RTEE STEE PIPING CLASS/Classe Tubazione 20367.PIP.MEC.FUN
1½ RT45 STEE WELDS EXAMINATION/Controllo Saldature 20377.PIP.MEC.FUN
2 (81) MATERIALS (if not otherw.stated)/Materiali(se non div.indicato) ASTM STANDARDS
3 (81) PIPING COMPONENTS/Componenti per tubazioni 05892.PIP.MEC.FUN
4 (81)
HEADER SIZE/Collettore
16 WLET WLET RTEE (81) ST45 STRAIGHT LATERAL TEE (NOTE 80) A234 WPB-S/W
18 TLET (3) OLAT RT45 (81) RT45 REDUCTION LATERAL TEE (NOTE 80) A234 WPB-S/W
. 36 (81)
T
U 1/2 3/4 1 1½ 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
B
.
DN" BRANCH SIZE/Derivazione
0 NOTES/Note :
0 1) All carbon steel bolting on flanges, valves & "Y" strainers shall be zinc coated (hot-dip) 31) Corrosion allowance to be considered and verified also for Body Valves and "Y" Strainers./
2
/ to ASTM A-153 La corrosione ammessa dovrà essere considerata e verificata per i corpi Valvole e Filtri.
4 80) Use only when indicated in PID 60) All the piping components for which heat treatment is not a mandatory requirement as per
S 2) To be used where required by P&I drawings only./Impiegare solo dove richiesto dagli ASTM A105 section 5.1 due to their pressure and rating shall be normalized (N).
h schemi di marcia. Supplementary requirement S2 of ASTM A105 shall apply and require Normalizing Heat
.
3) Threaded Ends and connections are allowed for instruments taps and test drain/vent only. treatment.
0
1 20) Deleted 61) For vessel connections with instrumentation, minimum size and rating are 2" and 300#.
/ 6) Valve suitable for fluid with methanol content >5% 63) Shall be in accordance with Sp. Item list doc. No. 220801DTEL20800 & Sp item data sheet doc. No. 220801DTGA23101
0
1 70) SCH 160 shall be used for 6" and SCH XS shall be used for 12" 81) S'TEE or ST45
to meet DNV minimum WT if the pipe penetrates HULL outer shell 82) Weldoflange/Nipoflange may be used for instrument tapping for thermowell.
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
Il presente documento è RISERVATO ed è di proprietà di ENI E&P. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
220801DTST23000
Eni S.p.A. Revisions/Rev.
E&P Division PIPING PROJECT SPECIFICATION
Sht/Foglio of/di Compiled/Compilato Date/Data
1 1 STCJ
SERVICE: CLOSED DRAIN, GLYCOL, RAW GAS (HYDROCARBON & NON ITEM CORR.ALLOWANCE
SCHEDULE/Schedula No. - 160 160 160 160 160 80 80 80 80 80 80 80 --- 80 --- --- --- --- --- --- --- ---
MATERIAL/Materiale ---- ASTM A106 Gr. B ASTM A672 Gr. C70 Cl. 22
MANUFACTURE/Costruzione ---- SMLS WLDD
WELDING NECK/Sald. di Testa ---- A105/600#-RJ (70)
FLANGES
SWAGES/Di Riduzione ASTM A106 Gr. B SMLS (3) ---- DRIP RINGS/Anelli di Drenaggio A105
THICKNESS/Spessori mm - 4.78 5.56 6.35 7.14 8.74 - - - SPECTACLE & SPACERS-BLINDS/Dischi a 8-Sezionatori A105
1/2 STEE REFERENCE SPECIFICATIONS/Specifiche di riferimento
3/4 STEE WELDING AND HEAT TREATMENT/Saldature e Trattamenti Termici 20368.PIP.MEC.FUN
1 RTEE STEE PIPING CLASS/Classe Tubazione 20367.PIP.MEC.FUN
1½ STEE WELDS EXAMINATION/Controllo Saldature 20377.PIP.MEC.FUN
2 STEE MATERIALS (if not otherw.stated)/Materiali(se non div.indicato) ASTM STANDARDS
3 STEE PIPING COMPONENTS/Componenti per tubazioni 05892.PIP.MEC.FUN
4 STEE
HEADER SIZE/Collettore
T 36 STEE
U
B 1/2 3/4 1 1½ 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
.
0
DN" BRANCH SIZE/Derivazione
0 NOTES/Note : 20) Deleted
2 1) All carbon steel bolting on flanges, valves & "Y" strainers shall be zinc coated (hot-dip)
/
4 to ASTM A-153
31) Corrosion allowance to be considered and verified also for Body Valve & Y Strainers.
S
h 2) To be used where required by P&I drawings only./Impiegare solo dove richiesto dagli 60) All the piping components for which heat treatment is not a mandatory requirement as per ASTM A105 section 5.1 due to their -
. schemi di marcia. pressure and rating shall be normalized (N). Supplementary requirement S2 of ASTM A105 shall apply and require Normalizing Heat-
0
3) Threaded Ends and connections are allowed for instruments taps and test drain/vent only. treatment for those parts.
1
/ 5) Angle Valve./Valvola ad angolo. 64) Heat treatment is required as per ASTM A105.
0 63) Shall be in accordance with Sp. Item list doc. No. 220801DTEL20800 & Sp item data sheet doc. No. 220801DTGA23101
1
70) RTJ Flanges size 2" and above shall be equipped with jackscrews or flange spreader bar shall be provided.
81) Weldoflange/Nipoflange may be used for instrument tapping for thermowell.
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
Il presente documento è RISERVATO ed è di proprietà di ENI E&P. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
220801DTST23000
Eni S.p.A. Revisions/Rev.
E&P Division PIPING PROJECT SPECIFICATION
Sht/Foglio of/di Compiled/Compilato Date/Data
1 1 STCJ
SERVICE: CLOSED DRAIN, UTILITY NITROGEN, WELL FLUID ITEM CORR.ALLOWANCE
Servizio: Sigla
42E Sovraspes. di Corr. 3 mm
RATING & FACING
Serie e Faccia 1500# RJ
DESIGN CONDITION: T - °C -10÷38 50 100 150 200 --- --- --- --- --- --- --- --- CODES- Design: ASME B 31.3/B16.5/B16.34
Condizioni di Progetto: P - bar 255.3 250.6 233.0 225.4 219.0 --- --- --- --- --- --- --- --- Norme-Progetto:
NOMINAL SIZE/Diametro nom. INCH - 1/2" 3/4" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 30" 36"
WALL THK./Spessore mm - 7.47 7.82 9.09 10.16 11.07 15.24 17.12 21.95 25.40 31.75 35.00 --- --- --- --- --- --- ---
PIPES
SCHEDULE/Schedula No. - XXS XXS XXS XXS XXS XXS XXS XXS --- --- --- --- --- --- --- --- --- ---
MATERIAL/Materiale ASTM A106 Gr. B
MANUFACTURE/Costruzione SMLS (20)
WELDING NECK/Sald. di Testa ---- A105/1500#-RJ (70) ----
FLANGES
SWAGES/Di Riduzione ASTM A106 Gr. B SMLS (2 (3) ---- DRIP RINGS/Anelli di Drenaggio A 105
THICKNESS/Spessori mm - 7.47 7.82 9.09 10.16 - - - - SPECTACLE & SPACERS-BLINDS/Dischi a 8-Sezionatori A 105
1/2 REFERENCE SPECIFICATIONS/Specifiche di riferimento
3/4 STEE WELDING AND HEAT TREATMENT/Saldature e Trattamenti Termici 20368.PIP.MEC.FUN
1 STEE PIPING CLASS/Classe Tubazione 20367.PIP.MEC.FUN
1½ RTEE STEE WELDS EXAMINATION/Controllo Saldature 20377.PIP.MEC.FUN
2 STEE MATERIALS (if not otherw.stated)/Materiali(se non div.indicato) ASTM STANDARDS
HEADER SIZE/Collettore
10 WLET(25) RTEE STEE Intersezioni RTEE REDUCTION BW TEE/T rid.Sald.di Testa A 234 Gr.WPB-S
D
.
18 RTSW REDUCTION SW TEE/T rid.Sald.Tasca
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
Il presente documento è RISERVATO ed è di proprietà di ENI E&P. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
220801DTST23000
Eni S.p.A. Revisions/Rev.
E&P Division PIPING PROJECT SPECIFICATION
Sht/Foglio of/di Compiled/Compilato Date/Data
1 1 STCJ
SERVICE: CRUDE OIL, CLOSED DRAIN, GLYCOL CLOSED DRAIN, ITEM CORR.ALLOWANCE
SCHEDULE/Schedula No. - XXS XXS XXS XXS XXS 160 120 80 80 XS XS XS XS XS XS XS 20 20 --- --- ---
MATERIAL/Materiale ASTM A106 Gr. B ASTM A672 Gr. C70 Cl. 22
MANUFACTURE/Costruzione SMLS WLDD
WELDING NECK/Sald. di Testa A105/600#-RF125Ra A105/150#-RF125Ra
FLANGES
NORMAL /Normali ASTM A106 Gr.B SMLS (3) ---- TEMP. STRAINERS/Filtri Temporanei
Nippli
SWAGES/Di Riduzione ASTM A106 Gr.B SMLS (3) ---- DRIP RINGS/Anelli di Drenaggio A105
THICKNESS/Spessori mm - 7.47 7.82 9.09 10.15 11.07 - - - SPECTACLE & SPACERS-BLINDS/Dischi a 8-Sezionatori A105
1/2 STEE REFERENCE SPECIFICATIONS/Specifiche di riferimento
3/4 STEE WELDING AND HEAT TREATMENT/Saldature e Trattamenti Termici 20368.PIP.MEC.FUN
1 RTEE STEE PIPING CLASS/Classe Tubazione 20367.PIP.MEC.FUN
1½ RT45 STEE WELDS EXAMINATION/Controllo Saldature 20377.PIP.MEC.FUN
2 (81) MATERIALS (if not otherw.stated)/Materiali(se non div.indicato) ASTM STANDARDS
3 (81) PIPING COMPONENTS/Componenti per tubazioni 05892.PIP.MEC.FUN
4 (81)
HEADER SIZE/Collettore
14 TLET (3) OLAT RT45 (81) RTSC REDUCTION THDD TEE/ T rid. Filettato
16 OLAT (81) ST45 STRAIGHT LATERAL TEE (NOTE 80) A234 WPB-S/W
E 1/2 3/4 1 1½ 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
C
. DN" BRANCH SIZE/Derivazione
T NOTES/Note :
U 1) All carbon steel bolting on flanges, valves & "Y" strainers shall be zinc coated (hot-dip)
B
. to ASTM A-153 21) In case of additional requirement S (NACE/ISO), components for NACE service
0 2) To be used where required by P&I drawings only./Impiegare solo dove richiesto dagli must be used (see also 06732 PIP.MEC.SDS)./In caso di indicazione S (NACE/ISO), i
0
2 schemi di marcia. componenti devono rispettare i requisiti NACE (vedere anche 06732 PIP.MEC.SDS).
/ 3) Threaded Ends and connections are allowed for instruments taps and test drain/vent only. 31) Corrosion allowance to be considered and verified also for Body Valves and "Y" Strainers./
4 65) thicknesses of 1/2" and 3/4" pipes are respectively of a calculated CA of 5,04 mm and 5,34 mm La corrosione ammessa dovrà essere considerata e verificata per i corpi Valvole e Filtri.
S with 1,5 mm minimum retired thickness in corroded conditions 63) Shall be in accordance with Sp. Item list doc. No. 220801DTEL20800 & Sp item data sheet doc. No. 220801DTGA23101
h 60) All the piping components for which heat treatment is not a mandatory requirement as per ASTM A105 section 5.1 due to their
. pressure and rating shall be normalized (N). Supplementary requirement S2 of ASTM A105 shall apply and require Normalizing heat t
0 6) Valve suitable for fluid with methanol content >5%
reatment for those parts
1
/ 20)Deleted 62) for vessel connection with instrumentat ion, minimum size and rating are 2" and 300#
0
1 70) SCH 160 shall be used for 6" and SCH XXS shall be used for 3" 80) Use only when indicated in PID
to meet DNV minimum WT if the pipe penetrates HULL outer shell 81) S'TEE or ST45
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
Il presente documento è RISERVATO ed è di proprietà di ENI E&P. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
220801DTST23000
Eni S.p.A. Revisions/Rev.
E&P Division PIPING PROJECT SPECIFICATION
Sht/Foglio of/di Compiled/Compilato Date/Data
1 1 STCJ
SERVICE: CRUDE OIL, CLOSED DRAIN ITEM CORR.ALLOWANCE
Servizio: Sigla
43B Sovraspes. di Corr. 6 mm
RATING & FACING
Serie e Faccia 300# RF 125Ra
DESIGN CONDITION: T - °C -10÷38 50 100 150 200 --- --- --- --- --- --- --- --- CODES- Design: ASME B 31.3/B16.5/B16.34
Condizioni di Progetto: P - bar 51.1 50.1 46.6 45.1 43.8 --- --- --- --- --- --- --- --- Norme-Progetto:
NOMINAL SIZE/Diametro nom. INCH - 1/2" 3/4" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 26" 28" 30" 32" 34" 36"
WALL THK./Spessore mm - 7.47 7.82 9.09 10.15 11.07 11.13 11.13 12.70 12.70 15.09 17.48 19.05 16.66 19.05 20.62 24.61 22.23 22.23 23.83 23.83 25.40 26.97
PIPES
SCHEDULE/Schedula No. - XXS XXS XXS XXS XXS 160 120 -- 80 80 80 80 60 60 60 60 --- --- --- --- --- ---
MATERIAL/Materiale ASTM A106 Gr. B ASTM A672 Gr. C70 Cl. 22
MANUFACTURE/Costruzione SMLS WLDD
WELDING NECK/Sald. di Testa A105/600#-RF125Ra A105/300#-RF125Ra
FLANGES
SWAGES/Di Riduzione ASTM A106 Gr. B SMLS (3) ---- DRIP RINGS/Anelli di Drenaggio A105
THICKNESS/Spessori mm - 7.47 7.82 9.09 10.15 11.07 - - - SPECTACLE & SPACERS-BLINDS/Dischi a 8-Sezionatori A105
1/2 STEE REFERENCE SPECIFICATIONS/Specifiche di riferimento
3/4 STEE WELDING AND HEAT TREATMENT/Saldature e Trattamenti Termici 20368.PIP.MEC.FUN
1 RTEE STEE PIPING CLASS/Classe Tubazione 20367.PIP.MEC.FUN
1½ STEE WELDS EXAMINATION/Controllo Saldature 20377.PIP.MEC.FUN
2 STEE MATERIALS (if not otherw.stated)/Materiali(se non div.indicato) ASTM STANDARDS
3 STEE PIPING COMPONENTS/Componenti per tubazioni 05892.PIP.MEC.FUN
4 STEE
HEADER SIZE/Collettore
0 36 STEE
2
/ 1/2 3/4 1 1½ 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
4
DN" BRANCH SIZE/Derivazione
S NOTES/Note : 31) Corrosion allowance to be considered and verified also for Body Valves and "Y" Strainers./
h 1) All carbon steel bolting on flanges, valves & "Y" strainers shall be zinc coated (hot-dip)
.
0 to ASTM A-153 60) All the piping components for which heat treatment is not a mandatory requirement as per ASTM A105 section 5.1 due to their
1 2) To be used where required by P&I drawings only. pressure and rating shall be normalized (N). Supplementary requirement S2 of ASTM A105 shall apply and require Normalizing
/
0 3) Threaded Ends and connections are allowed for instruments taps and test drain/vent only. heat treatment for those parts.
1 6) Valve suitable for fluid with methanol content >5% 63) Shall be in accordance with Sp. Item list doc. No. 220801DTEL20800 & Sp item data sheet doc. No. 220801DTGA23101
65) Thickness of 1/2" and 3/4" pipes are respectively of a calculated CA 5.07 mm and 5.34 mm with 1.5 mm of minimum retired
20) Deleted thickness in corroded condition.
81) Weldoflange/Nipoflange may be used for instrument tapping for thermowell.
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
Il presente documento è RISERVATO ed è di proprietà di ENI E&P. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
220801DTST23000
Eni S.p.A. Revisions/Rev.
E&P Division PIPING PROJECT SPECIFICATION
Sht/Foglio of/di Compiled/Compilato Date/Data
1 1 STCJ
SERVICE: CRUDE OIL, CLOSED DRAIN, WELL FLUID ITEM CORR.ALLOWANCE
Servizio: Sigla
43C Sovraspes. di Corr. 6 mm
RATING & FACING
Serie e Faccia 600# RJ
DESIGN CONDITION: T - °C -10÷38 50 100 150 200 --- --- --- --- --- --- --- --- CODES- Design: ASME B 31.3/B16.5/B16.34
Condizioni di Progetto: P - bar 102.1 100.2 93.2 90.2 87.6 --- --- --- --- --- --- --- --- Norme-Progetto:
NOMINAL SIZE/Diametro nom. INCH - 1/2" 3/4" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 26" 28" 30" 32" 34" 36"
WALL THK./Spessore mm - 7.47 7.82 9.09 10.16 11.07 11.13 13.49 14.27 18.26 18.26 20.62 23.83 23.83 26.97 28.58 33.32 33.95 36.50 38.25 40.64 42.36 45.28
PIPES
SCHEDULE/Schedula No. - XXS XXS XXS XXS XXS 160 160 120 120 100 -- 100 --- --- --- --- --- --- --- --- --- ---
MATERIAL/Materiale ---- ASTM A106 Gr. B ASTM A672 Gr. C70 Cl. 22
MANUFACTURE/Costruzione ---- SMLS WLDD
WELDING NECK/Sald. di Testa ---- A105/600#-RJ (70)
FLANGES
T 1/2 3/4 1 1½ 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
U
B DN" BRANCH SIZE/Derivazione
. NOTES/Note : 31) Corrosion allowance to be considered and verified also for Body Valves and "Y" Strainers./
0
0 1) All carbon steel bolting on flanges, valves & "Y" strainers shall be zinc coated (hot-dip) La corrosione ammessa dovrà essere considerata e verificata per i corpi Valvole e Filtri.
2 to ASTM A-153. 60) All the piping components for which heat treatment is not a mandatory requirement as per ASTM A105 section 5.1 due to their
/
2) To be used where required by P&I drawings only./Impiegare solo dove richiesto dagli pressure and rating shall be normalized (N). Supplementary requirement S2 of ASTM A105 shall apply and require Normalizing heat
4
schemi di marcia. treatment for those parts.
S 3) Threaded Ends and connections are allowed for instruments taps and test drain/vent only. 63) Shall be in accordance with Sp. Item list doc. No. 220801DTEL20800 & Sp item data sheet doc. No. 220801DTGA23101
h
. 5) Angle Valve./Valvola ad angolo. 64) Heat treatment is required as per ASTM A105.
0 6) Valve suitable for fluid with methanol content >5% 70) RTJ Flanges size 2" and above shall be equipped with jackscrews or flange spreader bar shall be provided.
1
/ 10) Depressurization "NOZZLE CHECK" type valve./Valvola per depressurizzazione tipo 81) Weldoflange/Nipoflange may be used for instrument tapping for thermowell.
0 "NOZZLE CHECK".
1
20) Deleted
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
Il presente documento è RISERVATO ed è di proprietà di ENI E&P. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
220801DTST23000
Eni S.p.A. Revisions/Rev.
E&P Division PIPING PROJECT SPECIFICATION
Sht/Foglio of/di Compiled/Compilato Date/Data
1 1 STCJ
SERVICE: BLOWDOWN (HOLD), CRUDE OIL, ATMOSPHERIC VENT ITEM CORR.ALLOWANCE
SCHEDULE/Schedula No. - XXS 160 160 160 160 80 40 40 40 STD STD STD STD STD STD STD STD STD 20 20 20 20
MATERIAL/Materiale ASTM A333 Gr. ASTM A671 Gr. CC70 Cl. 22 + S2
MANUFACTURE/Costruzione SMLS WLDD
WELDING NECK/Sald. di Testa A350 Gr.LF2 Cl.1/600#-RF125Ra A350 Gr.LF2 Cl.1/150#-RF125Ra
FLANGES
SWAGES/Di Riduzione ASTM A333 Gr. SMLS (3) ---- DRIP RINGS/Anelli di Drenaggio A350 Gr.LF2
THICKNESS/Spessori mm - 7.47 5.54 6.35 7.14 8.74 - - - SPECTACLE & SPACERS-BLINDS/Dischi a 8-Sezionatori A350 Gr.LF2
1/2 STEE REFERENCE SPECIFICATIONS/Specifiche di riferimento
3/4 STEE WELDING AND HEAT TREATMENT/Saldature e Trattamenti Termici 20376.PIP.MEC.FUN
1 RTEE STEE PIPING CLASS/Classe Tubazione 20367.PIP.MEC.FUN
1½ RT45 STEE WELDS EXAMINATION/Controllo Saldature 20377.PIP.MEC.FUN
2 (81) MATERIALS (if not otherw.stated)/Materiali(se non div.indicato) ASTM STANDARDS
3 (81) PIPING COMPONENTS/Componenti per tubazioni 05892.PIP.MEC.FUN
4 (81)
HEADER SIZE/Collettore
4 36 (81)
S 1/2 3/4 1 1½ 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
h DN" BRANCH SIZE/Derivazione
.
0 NOTES/Note :
1 1) All carbon steel bolting on flanges, valves & "Y" strainers shall be zinc coated (hot-dip)
/
0 to ASTM A-153 30) Grade LF2 to be Cl.1 ./ Grado LF2 dovrà essere Cl.1.
1 31) Corrosion allowance to be considered and verified also for Body Valves and "Y" Strainers./
2) To be used where required by P&I drawings only./Impiegare solo dove richiesto dagli La corrosione ammessa dovrà essere considerata e verificata per i corpi Valvole e Filtri.
schemi di marcia. 63) Shall be in accordance with Sp. Item list doc. No. 220801DTEL20800 & Sp item data sheet doc. No. 220801DTGA23101
3) Threaded Ends and connections are allowed for instruments taps and test drain/vent only. 80) Use only when indicated in PID
81) S'TEE or ST45
20) Deleted
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
Il presente documento è RISERVATO ed è di proprietà di ENI E&P. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
220801DTST23000
Eni S.p.A. Revisions/Rev.
E&P Division PIPING PROJECT SPECIFICATION
Sht/Foglio of/di Compiled/Compilato Date/Data
1 1 STCJ
SERVICE: BLOWDOWN (HOLD), CLOSED DRAIN, GLYCOL, RAW GAS, ITEM CORR.ALLOWANCE
Servizio: Sigla
52C Sovraspes. di Corr. 3 mm
CRUDE OIL, TREATED GAS
RATING & FACING
(HYDROCARBON & NON HYDROCARBON) Serie e Faccia 600# RJ
DESIGN CONDITION: T - °C -40÷38 50 100 120 --- --- --- --- --- --- --- --- --- CODES- Design: ASME B 31.3/B16.5/B16.34
Condizioni di Progetto: P - bar 96.0 94.9 90.7 89.5 --- --- --- --- --- --- --- --- --- Norme-Progetto:
NOMINAL SIZE/Diametro nom. INCH - 1/2" 3/4" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 26" 28" 30" 32" 34" 36"
WALL THK./Spessore mm - 7.47 5.56 6.35 7.14 8.74 7.62 8.56 10.97 12.70 15.09 17.48 19.05 21.44 22.23 23.83 28.58 30.50 31.55 33.00 36.00 36.87 39.50
PIPES
SCHEDULE/Schedula No. - XXS 160 160 160 160 80 80 80 80 80 80 80 80 -- -- -- --- --- --- --- --- ---
MATERIAL/Materiale ASTM A333 Gr. 6 ASTM A671 Gr. CC70 Cl. 22 + S2
MANUFACTURE/Costruzione SMLS WLDD
WELDING NECK/Sald. di Testa A350 Gr.LF2 Cl.1/600#-RJ (70)
FLANGES
SWAGES/Di Riduzione ASTM A333 Gr. 6 SMLS (3) ---- DRIP RINGS/Anelli di Drenaggio A 350 Gr.LF2
THICKNESS/Spessori mm - 4.78 5.56 6.35 7.14 8.74 - - - SPECTACLE & SPACERS-BLINDS/Dischi a 8-Sezionatori A 350 Gr.LF2
1/2 REFERENCE SPECIFICATIONS/Specifiche di riferimento
3/4 STEE WELDING AND HEAT TREATMENT/Saldature e Trattamenti Termici 20376.PIP.MEC.FUN
1 STEE PIPING CLASS/Classe Tubazione 20367.PIP.MEC.FUN
1½ RTEE STEE WELDS EXAMINATION/Controllo Saldature 20377.PIP.MEC.FUN
2 STEE MATERIALS (if not otherw.stated)/Materiali(se non div.indicato) ASTM STANDARDS
3 STEE PIPING COMPONENTS/Componenti per tubazioni 05892.PIP.MEC.FUN
4 STEE
HEADER SIZE/Collettore
0 36 STEE
2
/ 1/2 3/4 1 1½ 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
4 DN" BRANCH SIZE/Derivazione
S NOTES/Note :
h 1) All carbon steel bolting on flanges, valves & "Y" strainers shall be zinc coated (hot-dip)
.
to ASTM A-153 30) Grade LF2 to be Cl.1 / Grado LF2 dovrà essere Cl.1
0
1 31) Corrosion allowance to be considered and verified also for Body Valves and "Y" Strainers./
/ 2) To be used where required by P&I drawings only./Impiegare solo dove richiesto dagli La corrosione ammessa dovrà essere considerata e verificata per i corpi Valvole e Filtri.
0
1 schemi di marcia. 63) Shall be in accordance with Sp. Item list doc. No. 220801DTEL20800 & Sp item data sheet doc. No. 220801DTGA23101
3) Threaded Ends and connections are allowed for instruments taps and test drain/vent only. 70) RTJ Flanges size 2" and above shall be equipped with jackscrews or flange spreader bar shall be provided.
6) Valve suitable for fluid with methanol content >5%
20) Deleted
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
Il presente documento è RISERVATO ed è di proprietà di ENI E&P. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
220801DTST23000
Eni S.p.A. Revisions/Rev.
E&P Division PIPING PROJECT SPECIFICATION
Sht/Foglio of/di Compiled/Compilato Date/Data
1 1 STCJ
SERVICE: BLOWDOWN (HOLD) (HYDROCARBON) ITEM CORR.ALLOWANCE
Servizio: Sigla
53B Sovraspes. di Corr. 6 mm
RATING & FACING
Serie e Faccia 300# RF 125Ra
DESIGN CONDITION: T - °C -40÷38 50 100 120 --- --- --- --- --- --- --- --- --- CODES- Design: ASME B 31.3/B16.5/B16.34
Condizioni di Progetto: P - bar 48.0 47.5 45.3 44.7 --- --- --- --- --- --- --- --- --- Norme-Progetto:
NOMINAL SIZE/Diametro nom. INCH - 1/2" 3/4" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 26" 28" 30" 32" 34" 36"
WALL THK./Spessore mm - 7.47 7.82 9.09 10.16 11.07 11.13 13.49 14.27 15.09 15.09 17.48 15.09 16.66 19.05 20.62 24.59 20.62 22.23 22.23 23.83 23.83 25.40
PIPES
SCHEDULE/Schedula No. - XXS XXS XXS XXS XXS 160 160 120 100 80 80 60 60 60 60 60 --- --- --- --- --- ---
MATERIAL/Materiale ASTM A333 Gr. 6 ASTM A671 Gr. CC70 Cl. 22 + S2
MANUFACTURE/Costruzione SMLS WLDD
WELDING NECK/Sald. di Testa A350 Gr.LF2 Cl.1/600#-RF125Ra A350 Gr.LF2 Cl.1/300#-RF125Ra
FLANGES
SWAGES/Di Riduzione ASTM A333 Gr. 6 SMLS (3) ---- DRIP RINGS/Anelli di Drenaggio A 350 Gr. LF2
THICKNESS/Spessori mm - 7.47 7.82 9.09 10.16 11.07 - - - SPECTACLE & SPACERS-BLINDS/Dischi a 8-Sezionatori A 350 Gr. LF2
1/2 STEE REFERENCE SPECIFICATIONS/Specifiche di riferimento
3/4 STEE WELDING AND HEAT TREATMENT/Saldature e Trattamenti Termici 20376.PIP.MEC.FUN
1 RTEE STEE PIPING CLASS/Classe Tubazione 20367.PIP.MEC.FUN
1½ STEE WELDS EXAMINATION/Controllo Saldature 20377.PIP.MEC.FUN
2 STEE MATERIALS (if not otherw.stated)/Materiali(se non div.indicato) ASTM STANDARDS
3 STEE PIPING COMPONENTS/Componenti per tubazioni 05892.PIP.MEC.FUN
4 STEE
HEADER SIZE/Collettore
E
28 STEE SLET SOCKOLETS
C
. 30 STEE NLET NIPOLETS THDD / Nipolets Filettate
T
U
32 STEE OELW WELDOFLANGE A 350 Gr. LF2
B 34 STEE
.
0 36 STEE
0 1/2 3/4 1 1½ 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
2
/ DN" BRANCH SIZE/Derivazione
4 NOTES/Note :
S 1) All carbon steel bolting on flanges, valves & "Y" strainers shall be zinc coated (hot-dip)
h to ASTM A-153 30) Grade LF2 to be Cl.1 .
.
31) Corrosion allowance to be considered and verified also for Body Valves and "Y" Strainers./
0
1 2) To be used where required by P&I drawings only.
/ 63) Shall be in accordance with Sp. Item list doc. No. 220801DTEL20800 & Sp item data sheet doc. No. 220801DTGA23101
0
1 3) Threaded Ends and connections are allowed for instruments taps and test drain/vent only. 65) Thicknesses of 1/2" and 3/4" pipes are respectively of a calculated CA of 5.04 mm and 5.34 mm with minimum 1.5 mm retired
6) Valve suitable for fluid with methanol content >5% thickness in corroded condition.
20) Deleted 66) VB 913 PR 7D1
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
Il presente documento è RISERVATO ed è di proprietà di ENI E&P. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
220801DTST23000
Eni S.p.A. Revisions/Rev.
E&P Division PIPING PROJECT SPECIFICATION
Sht/Foglio of/di Compiled/Compilato Date/Data
1 1 STCJ
SERVICE: BLOWDOWN (HOLD) (HYDROCARBON) ITEM CORR.ALLOWANCE
Servizio: Sigla
53C Sovraspes. di Corr. 6 mm
RATING & FACING
Serie e Faccia 600# RJ
DESIGN CONDITION: T - °C -40÷38 50 100 120 --- --- --- --- --- --- --- --- --- CODES- Design: ASME B 31.3/B16.5/B16.34
Condizioni di Progetto: P - bar 96.0 94.9 90.7 89.5 --- --- --- --- --- --- --- --- --- Norme-Progetto:
NOMINAL SIZE/Diametro nom. INCH - 1/2" 3/4" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 26" 28" 30" 32" 34" 36"
WALL THK./Spessore mm - 7.47 7.82 9.09 10.16 11.07 11.13 13.49 14.27 18.26 18.26 21.44 23.83 26.19 29.36 32.54 38.89 33.95 36.00 36.50 38.64 40.29 43.28
PIPES
SCHEDULE/Schedula No. - XXS XXS XXS XXS XXS 160 160 120 120 100 100 100 100 100 100 100 --- --- --- --- --- ---
MATERIAL/Materiale ASTM A333 Gr. 6 ASTM A671 Gr. CC70 Cl. 22 + S2
MANUFACTURE/Costruzione SMLS WLDD
WELDING NECK/Sald. di Testa A350 Gr.LF2 Cl.1/600#-RJ (70)
FLANGES
MANUAL CONTROL
Regolaz. Man.
---- ----
CHECK (31) VDR 735 AG AR2 - RJ VDR 715 AG 6D2 - RJ (Wafer-Tilting)
Ritegno
---- ----
SPECIAL USE VB 915 PR 7D1 - RJ-2"
FOR INSTRUMENT VD 935 PR 6R1 ----
" Y "STRAINERS/Filtri a "Y" (63)
90°-45° ELBOWS/Curve 90°-45° ---- A 420 Gr.WPL6 - SMLS (BW) A 420 Gr.WPL6 - WLDD (BW)
ECC.-CONC.REDUCT./Rid.Conc.-Ecc. ---- A 420 Gr.WPL6 - SMLS (BW) A 420 Gr.WPL6 - WLDD (BW)
ELLIPT.CAPS/Fondelli Bombati ---- A 420 Gr.WPL6 - SMLS (BW)
LJ STUB ENDS/Collari Flg.Libere ---- ----
PIPE BENDS/Curve da Tubo ---- ----
MITER ELBOWS/Curve a Spicchi ---- ----
S.W. FITTINGS/Raccorderia S.W. ---- COMPONENTS/Componenti MAT./Mat. (30)
THDD FITTINGS/Raccorderia Fil. ---- ---- RED.FLG.S/FLG di Rid. THDD./Filet. S.O./a Sovr. ----
ASTM A333 Gr. 6 SMLS ---- (63)
NIPPLES
SWAGES/Di Riduzione ASTM A333 Gr. 6 SMLS ---- DRIP RINGS/Anelli di Drenaggio A 350 Gr.LF2 Cl.1
THICKNESS/Spessori mm - 7.47 7.82 9.09 10.16 11.07 - - - SPECTACLE & SPACERS-BLINDS/Dischi a 8-Sezionatori A 350 Gr.LF2 Cl.1
1/2 REFERENCE SPECIFICATIONS/Specifiche di riferimento
3/4 STEE WELDING AND HEAT TREATMENT/Saldature e Trattamenti Termici 20376.PIP.MEC.FUN
1 STEE PIPING CLASS/Classe Tubazione 20367.PIP.MEC.FUN
1½ RTEE STEE WELDS EXAMINATION/Controllo Saldature 20377.PIP.MEC.FUN
2 STEE MATERIALS (if not otherw.stated)/Materiali(se non div.indicato) ASTM STANDARDS
3 STEE PIPING COMPONENTS/Componenti per tubazioni 05892.PIP.MEC.FUN
4 STEE
HEADER SIZE/Collettore
4 36 STEE
S 1/2 3/4 1 1½ 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
h DN" BRANCH SIZE/Derivazione
.
0 NOTES/Note : 30) Grade LF2 to be Cl.1
1 1) All carbon steel bolting on flanges, valves & "Y" strainers shall be zinc coated (hot-dip) 31) Corrosion allowance to be considered and verified also for Body Valves and "Y" Strainers.
/
0 to ASTM A-153
1 2) To be used where required by P&I drawings only. 63) Shall be in accordance with Sp. Item list doc. No. 220801DTEL20800 & Sp item data sheet doc. No. 220801DTGA23101
schemi di marcia 70) RTJ Flanges size 2" and above shall be equipped with jackscrews or flange spreader bar shall be provided.
20) Deleted 81) Weldoflange/Nipoflange may be used for instrument tapping for thermowell.
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
Il presente documento è RISERVATO ed è di proprietà di ENI E&P. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
220801DTST23000
Eni S.p.A. Revisions/Rev.
E&P Division PIPING PROJECT SPECIFICATION Sht/Foglio of/di
of/di Compiled/Compilato Date/Data
SPECIFICA DI PROGETTO TUBAZIONI 1 / 1 STCJ
SERVICE: CRUDE OIL, CLOSED DRAIN, RAW GAS, BLOWDOWN, ITEM CORR.ALLOWANCE
CHEMICAL (GENERAL), UTILITY WATER, COOLING WATER, Sigla 55A
Servizio:
OPEN DRAIN, DIESEL TREATED, FIRE FIGHTING FOAM,
Sovraspes. di Corr. 0 mm
FOAMING LIQUID, GLYCOL, LUBE OIL, PRODUCED WATER, RATING & FACING
Serie e Faccia
ATMOSPHERIC VENT 150# RF 125Ra
SCHEDULE/Schedula No. - 40S 40S 40S 40S 40S 10S 10S 10S 40S 40S 40S 10S 10S 10S 10S 10S --- --- 10S --- --- ---
MATERIAL/Materiale ASTM A312 TP 316/316L (61) ASTM A358 Gr.316/316L CLASS 1 EFW (61)
MANUFACTURE/Costruzione SMLS WLDD
WELDING NECK/Sald. di Testa A182 Gr.F316/316L/600#-RF125Ra (61) A182 Gr.F316/316L/150# -RF 125 Ra (61)
FLANGES
SWAGES/Di Riduzione A 312 TP 316/316L SMLS(3) (61) ---- DRIP RINGS/Anelli di Drenaggio A182 F316/316L (61)
THICKNESS/Spessori mm - 2.77 2.87 3.38 3.68 3.91 - - - SPECTACLE & SPACERS-BLINDS/Dischi a 8-Sezionatori A182 F316/316L (61)
1/2 STEE REFERENCE SPECIFICATIONS/Specifiche di riferimento
3/4 STEE WELDING AND HEAT TREATMENT/Saldature e Trattamenti Termici 20370.PIP.MEC.SPC
1 RTEE STEE PIPING CLASS/Classe Tubazione 20367.PIP.MEC.FUN
1½ STEE WELDS EXAMINATION/Controllo Saldature 20377.PIP.MEC.FUN
2 STEE MATERIALS (if not otherw.stated)/Materiali(se non div.indicato) ASTM STANDARDS
3 STEE COMPONENTS STANDARD SPEC./Specifica Generale Componenti 05892.PIP.MEC.FUN
4 STEE
HEADER SIZE/Collettore
D 14 TLET (3) WLET RTEE STEE RTSC REDUCTION THDD TEE/ T rid. Filettato
.
M 16 STEE STSW STRAIGHT SW TEE/ T da Sal.a Tasca
E 18 STEE RTSW REDUCTION SW TEE/T rid.Sald.Tasca
C
. 20 STEE SWLT SWEEPOLETS
DN"
36 STEE
S
h 1/2 3/4 1 1½ 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
.
0 DN" BRANCH SIZE/Derivazione
1 NOTES/Note:
/
2) To be used where required by P&I drawings only. 62) For Vessel connections with instrumentation, minimum size and rating 2" and 300#
0
1 63) Shall be in accordance with Sp. Item list doc. No. 220801DTEL20800 & Sp item data sheet doc. No. 220801DTGA23101
3) Threaded Ends and connections are allowed for instruments taps and test drain/vent only. 66) Valves design "Non-Cryogenic" for corrosive hydrocarbons, in accordance with the design condition -120 degC, material
Stainless Steel without stem extension, valve operation limited down to -46 degC.
61) All 316 materials must be dual certified 316/316L; all castings must be dual certified
CF3M/CF8M.
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
Il presente documento è RISERVATO ed è di proprietà di ENI E&P. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
220801DTST23000
Eni S.p.A. Revisions/Rev.
E&P Division Sht/Foglio of/di
of/di Compiled/Compilato Date/Data
PIPING PROJECT SPECIFICATION
1 / 1 STCJ
SERVICE: CLOSED DRAIN, RAW GAS, VENT ATMOSPHERE, BLOWDOWN, ITEM CORR.ALLOWANCE
Servizio: CRUDE OIL, TREATED GAS, FUEL GAS, WELL FLUID Sigla
55C Sovraspes. di Corr. 0 mm
(HYDROCARBON) RATING & FACING
Serie e Faccia 600# RJ
DESIGN CONDITION: T - °C -120÷38 50 100 --- --- --- --- --- --- --- --- --- --- CODES- Design: ASME B 31.3/B16.5/B16.34
Condizioni di Progetto: P - bar 99.3 96.2 84.4 --- --- --- --- --- --- --- --- --- --- Norme-Progetto:
NOMINAL SIZE/Diametro nom. INCH - 1/2" 3/4" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 26" 28" 30" 32" 34" 36"
WALL THK./Spessore mm - 2.77 2.87 3.38 3.68 3.91 5.49 6.02 7.11 10.31 12.70 14.27 15.09 16.66 19.05 20.62 24.61 26.97 28.58 31.75 32.51 34.55 39.50
PIPES
SCHEDULE/Schedula No. - 40S 40S 40S 40S 40S 40S 40S 40S --- 80S --- --- --- --- --- --- --- --- --- --- --- ---
MATERIAL/Materiale ASTM A312 TP 316/316L (61) ASTM A358 Gr.316/316L CLASS 1 EFW (61)
MANUFACTURE/Costruzione SMLS WLDD
WELDING NECK/Sald. di Testa A182 Gr.F316/316L/600#-RJ (61) (70)
FLANGES
MANUAL CONTROL
Regolaz. Man.
---- ----
CHECK VDR 735 PR 8R1 - RJ VDR 735 PR BR2 - RJ (Swing)
Ritegno (61)
---- VDR 735 PR 5S1 - RJ (Wafer -Dual Plate)
VB 935 PR 7R1-RJ-2"
SPECIAL USE
FOR INSTRUMENT
VB 935 PR 9R1-RF x NPT
VD 935 PR 6R1 - RJ ----
" Y "STRAINERS/Filtri a "Y" (63)
90°-45° ELBOWS/Curve 90°-45° A 403 Gr.WP 316/316L - S (61) (BW) A 403 Gr.WP 316/316L - W (61) (BW)
ECC.-CONC.REDUCT./Rid.Conc.-Ecc. A 403 Gr.WP 316/316L - S (61) (BW) A 403 Gr.WP 316/316L - W (61) (BW)
ELLIPT.CAPS/Fondelli Bombati A 403 Gr.WP 316/316L - S (61) (BW)
LJ STUB ENDS/Collari Flg.Libere ---- ----
PIPE BENDS/Curve da Tubo ---- ----
MITER ELBOWS/Curve a Spicchi ---- ----
S.W. FITTINGS/Raccorderia S.W. ---- ---- COMPONENTS/Componenti MAT./Mat.
THDD FITTINGS/Raccorderia Fil. A182 Gr.F316/316L/3000# NPT(3) (61) ---- RED.FLG.S/FLG di Rid. THDD./Fil. S.O./a Sovr. A182 F316/316L (3) (61)
A 312 TP 316/316L SMLS(3) (61) ---- (63)
NIPPLES
SWAGES/Di Riduzione A 312 TP 316/316L SMLS(3) (61) ---- DRIP RINGS/Anelli di Drenaggio A182 F316/316L (61)
THICKNESS/Spessori mm - 2.77 2.87 3.38 3.68 3.91 - - - SPECTACLE & SPACERS-BLINDS/Dischi a 8-Sezionatori A182 F316/316L (61)
1/2 STEE REFERENCE SPECIFICATIONS/Specifiche di riferimento
3/4 STEE WELDING AND HEAT TREATMENT/Saldature e Trattamenti Termici 20370.PIP.MEC.SPC
1 RTEE STEE PIPING CLASS/Classe Tubazione 20367.PIP.MEC.FUN
1½ STEE WELDS EXAMINATION/Controllo Saldature 20377.PIP.MEC.FUN
2 STEE MATERIALS (if not otherw.stated)/Materiali(se non div.indicato) ASTM STANDARDS
3 STEE COMPONENTS STANDARD SPEC./Specifica Generale Componenti 05892.PIP.MEC.FUN
4 STEE
HEADER SIZE/Collettore
4 34 STEE
S 36 STEE
h 1/2 3/4 1 1½ 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
.
0 DN" BRANCH SIZE/Derivazione
1 NOTES/Note:
/
0 2) To be used where required by P&I drawings only. 63) Shall be in accordance with Sp. Item list doc. No. 220801DTEL20800 & Sp item data sheet doc. No. 220801DTGA23101
1 66) Valves design "Non-Cryogenic" for corrosive hydrocarbons, in accordance witth the design condition -120 degC, material
3) Threaded Ends and connections are allowed for instruments taps and test drain/vent only. Stainless Steel without stem extension, valve operation limited down to -46 degC.
6) Valve suitable for fluid with methanol content >5% 70) RTJ Flanges size 2" and above shall be equipped with jackscrews or flange spreader bar shall be provided.
61) All 316 materials must be dual certified 316/316L; all castings must be dual certified
CF3M/CF8M.
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
Il presente documento è RISERVATO ed è di proprietà di ENI E&P. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.
220801DTST23000
Eni S.p.A. Revisions/Rev.
E&P Division Sht/Foglio of/di
of/di Compiled/Compilato Date/Data
PIPING PROJECT SPECIFICATION
1 / 1 STCJ
SERVICE: WELL FLUID ITEM CORR.ALLOWANCE
Servizio:
55F Sovraspes. di Corr. 0 mm
(HYDROCARBON) RATING & FACING
Serie e Faccia 2500# RJ
DESIGN CONDITION: T - °C -120÷38 50 100 --- --- --- --- --- --- --- --- --- --- CODES- Design: ASME B 31.3/B16.5/B16.34 (Group 2.2)
Condizioni di Progetto: P - bar 413.7 400.9 351.6 --- --- --- --- --- --- --- --- --- --- Norme-Progetto:
NOMINAL SIZE/Diametro nom. INCH - 1/2" 3/4" 1" 1½" 2" 3" 4" 6" 8" 10" 12"
WALL THK./Spessore mm - 7.47 5.56 6.35 10.16 11.07 15.24 19.05 28.58 34.00 42.00 50.00
PIPES
SCHEDULE/Schedula No. - --- --- --- --- --- --- --- --- --- --- ---
MATERIAL/Materiale ASTM A312 TP 316/316L (61)
MANUFACTURE/Costruzione SMLS
WELDING NECK/Sald. di Testa A182 Gr.F316/316L/2500#-RJ (61)
FLANGES
ON/OFF
MANUAL CONTROL
Regolaz. Man.
(61)
CHECK
Ritegno
SWAGES/Di Riduzione A 312 TP 316/316L SMLS(3) ---- DRIP RINGS/Anelli di Drenaggio A182 F316/316L (61)
THICKNESS/Spessori mm - - - - - - - - - SPECTACLE & SPACERS-BLINDS/Dischi a 8-Sezionatori A182 F316/316L (61)
1/2 STEE REFERENCE SPECIFICATIONS/Specifiche di riferimento
3/4 STEE WELDING AND HEAT TREATMENT/Saldature e Trattamenti Termici 20370.PIP.MEC.SPC
1 RTEE STEE PIPING CLASS/Classe Tubazione 20367.PIP.MEC.FUN
1½ STEE WELDS EXAMINATION/Controllo Saldature 20377.PIP.MEC.FUN
2 STEE MATERIALS (if not otherw.stated)/Materiali(se non div.indicato) ASTM STANDARDS
HEADER SIZE/Collettore
13) This specification can in principle be used when additional requirement S (NACE/ISO)
applies, provided that all components fulfill prescriptions for NACE service (see also
06732 PIP.MEC.SDS).
This document is CONFIDENTIAL and the sole property of ENI E&P. It shall neither be shown to third parties nor used for purposes other than those for which it has been sent.
Il presente documento è RISERVATO ed è di proprietà di ENI E&P. Esso non sarà mostrato a Terzi né sarà utilizzato per scopi diversi da quelli per i quali è stato inviato.