Documente Academic
Documente Profesional
Documente Cultură
June 2004
BASIC COMPONENT SYMBOLS
MAIN AUX.
PUMP: VARIABLE and
PUMP or MOTOR FLUID CONDITIONER SPRING CONTROL VALVES RESTRICTION LINE RESTRICTION 2-SECTION PUMP PRESSURE COMPENSATED
(FIXED)
VARIABILITY SPRING LINE RESTRICTION PRESSURE HYDRAULIC PNEUMATIC LINE RESTRICTION ATTACHMENT
(ADJUSTABLE) (VARIABLE) COMPENSATION ENERGY TRIANGLES VARIABLE and PRESSURE
COMPENSATED
VALVES
K VALVE ENVELOPES VALVE PORTS
P T P T
BASIC SPRING SHUTTLE PILOT
NORMAL POSITION SHIFTED POSITION INFINITE POSITION
SYMBOL LOADED CONTROLLED
Steering charge circuit oil enter the charge filter (25) through the right hand
COMBINATION CONTROLS
fitting.Clean filtered charge circuit oil exits the filter at the left hand fitting and
flows to thepilot steering control and the steering pump.
CCK1-0499
A combination S•O•S and fluid sampling port (K) is installed on the inlet side CBL1-0399 SOLENOID SOLENOID
or MANUAL
SOLENOID
and PILOT
SOLENOID and
PILOT or MANUAL
SERVO THERMAL DETENT
SPRING LOADED GAS CHARGED LINES CROSSING LINES JOINING SINGLE ACTING DOUBLE ACTING
UNIDIRECTIONAL UNIDIRECTIONAL
Differential Steering
© 2004 Caterpillar Printed in U.S.A.
All Rights Reserved
Dimensions (approximate)
Electrical Symbols Table
Hydraulic Symbols (Electrical)
G M
3
7
Transducer Transducer Generator Electric Motor
(Fluid) (Gas / Air)
1 5 8
2 6
D E A Pressure Switch Pressure Switch Temperature Switch Electrical Wire
(Adjustable)
RENR5258
Tractor Dimensions
1 Track gauge 1890 mm 74 in Electrical Symbols (Electrical)
2 Width of tractor
SOS With the following attachments:
B Standard shoes without blade 2492 mm 98 in
T
Pressure Temperature Level Flow
840 mm (33 in) shoes without blade — Symbol Symbol Symbol Symbol
Standard shoes with VPAT blade angled 25 2960 mm 117 in
3 Machine height from tip of grouser
: Wire Number Identification Codes
The implement pump (16) is mounted
to the lower left rear face of the torque With the following equipment —
ROPS canopy 3022 mm 119 in Electrical Schematic Example Hydraulic Schematic Example
converter housing.
ROPS cab 3083 mm 121 in Current Standard Current Standard
16 Page,
wire 135 in harness "AG". Wire
Y2 Y1 MA MB Circuit Number Wire Color
5 Length of track on ground 2550 mm 100 in Identification
325-AG135 PK-14
6 Length of basic tractor (with drawbar) 3740 mm 147 in
325-PK
Located inside the machine right fender outside compartment is the Hydraulic Pressure With the following attachments, Circuit Identification Wire Color Wire Gauge
Remote Test Port panel. Machine system pressures can be checked and monitored Number
add to basic tractor length: —
here. The arrangement of the pressure ports on this panel are:
- A Implement pump discharge.
Ripper 1026 mm 41 in Previous Standard
- B Implement pump signal. PA55 winch 381 mm 15 in Wire
Wire Color
(EXAMPLE VALVE)
20 C 20 End Cover 1
21 Make-up Valve Group 2
22 Ripper Lift Valve Group 1
AA BB 23 Make-up Valve Group with Line Relief 2
21 24 Dozer Angle Valve Group (STD) 1
25 Cylinder Group (Ripper Lift) 2
26 Dozer Tilt Valve Group (STD) 1
22 17 27 Make-up Valve Group with Line Relief (Dozers with “SU” Blade or Ripper) 1
Dozer Lift Valve Group (Standard “P” Lift) 1
28
Dozer Lift Valve Group (Dozers with “SU” Blade or Ripper) 1
Inlet Manifold Cover Assembly 1
23 29
4 Bank Valve Group (All Dozers with Ripper) 1
30 3 Bank Valve Group (Standard “P” Dozer) 1
Q
24 18 19 R 2 Bank Valve Group (“SU” Blade) 1
31 Float Detent 1
32 Filter Element 1
14 13 12 33 Tank Group 1
34 Case Drain Filter 1
25
D6N D/S Schematic
15 P Item Description
Line AA-BB Blocked for Power Beyond End Cover
A
Line AA-BB Open for Standard End Cover
B Implement Pump Discharge Pressure Tap
C For Power Beyond Use 4T-7862 End Cover
W D Bypassed Cold Oil
V E Right Steering Loop Pressure
F Left Steering Loop Pressure
(Dimensions: 34 inches x 24 inches)
34
30 T
LINE PATTERNS
S Pressure Line
Component Group
33
Attachment
32
Air Line
CALLOUTS
THIS SCHEMATIC IS FOR THE D6N TRACK-TYPE TRACTOR
YY Taps (Pressure, Sampling,Sensor) by letter Components are shown installed on a fully operable machine with the key and engine off.
52 Components by number Refer to the appropriate Service Manual for Troubleshooting, Specifications and Systems Operations