Documente Academic
Documente Profesional
Documente Cultură
Clogging Indicators
Early warning pressure devices protect the hydraulic circuit from
contamination, alerting the operator that the filter element is near capacity
and must be changed. The clogging indicator is typically set to trip at 1-bar
(14 psid) below the filter bypass setting, to allow the operator sufficient time
for element change-out. Available in visual, combo electrical/visual, as well
as an extensive list of other options and certifications. A comprehensive
offering of clogging indicators ensures that any application can be
accommodated.
Introduction G2
General Indicator Type
G4
Drawings
Standard Indicators
Vacuum G6
Return line G8
Differential pressure G21
Mobile Indicators
Return line G29
Differential pressure G30
ATEX Indicators
Return line G32
Differential pressure G34
UL/CSA Indicators
Return line G36
Differential pressure G36
Model Code - Standard G38
Dual Indicator / Gauge Blocks G40
Cap
Spring
Piston
Profile Seal
Spring
Housing
Piston
O-ring
High Pressure Side (before element - dirty side)
Plug Low Pressure Side (after element - clean side)
Standard without
Dome Cap;
Indicator pin (Red) (For Indicator with optional
Dome Cap contact HYDAC)
Piston
Housing
Spring
Diaphragm
O-ring
Threaded Body
Fluid Port
High Pressure Side (before element - dirty side)
VR x UE.x
Type of indication Visual-analog, scale indication [ø1.97]
Weight 0.28 lbs (125 g) ø50
Trip Pressure / Range use w/3 psi (0.2 bar) bypass valve
Permitt. operating pressure -30 inHg to 0 inHg
[1.20]
Permitt. temperature range -40°F to 200°F (-40°C to 93°C) 30.5
[1.84]
Thread 1/8” NPTF 46.8
Max. torque Refer to end of section G HEX 14
Switching type –
1/8 NPTF
Max. switching voltage –
Electrical connection –
Max. switching voltage at
–
resistive load
Switching capacity –
Protection class to DIN 40050 –
Order example VMF0.2UE.0/3
VMF x UF.x
Type of indication Electrical switch [ø1.26]
Weight 0.37 lbs (170 g) ø32
VR x UF.x
Type of indication Electrical switch [ø1.26]
Weight 0.37 lbs (170 g)
ø32
VR x B.x
Type of indication visual, red pin
Weight 0.10 lbs (44 g)
29 psi -2.9 psi [ø0.39]
Trip Pressure / Range*
(2 bar -0.2 bar) [~0.20] ø10
~5 Hub
Permitt. operating pressure 102 psi (7 bar)
Permitt. temperature range -22˚F to 212˚F (-30°C to 100°C)
Thread G 1/2
Max. torque Refer to end of section G [~1.87]
~47.5
[~2.34]
Switching type – ~59.5
HEX 30
Max. switching voltage –
Electrical connection –
Max. switching voltage at
–
resistive load [0.47]
Switching capacity – G1/2 12
VMF x C.x
Type of indication Electrical switch
Weight 0.60 lbs (270 g)
29 psi -4.4 psi (2 bar -0.3 bar)
Trip Pressure / Range*
73 psi -7.3 psi (5 bar -0.5 bar)
[~1.34] [1.10]
Permitt. operating pressure 580 psi (40 bar) ~34 28
*When presented as a pressure followed by a negative (ex 29 psi -4.4 psi), the 4.4 is the lower tolerance. This is not to be interpreted as a range (ex 4.4 - 29 psi).
The range in this instance would be 24.6 - 29 psi. Indicators are not field adjustable.
VR x D.x /-L…
Type of indication Visual indicator & electrical switch
Weight 0.79 lbs (360 g)
29 psi -4.4 psi (2 bar -0.3 bar)
Trip Pressure / Range*
73 psi -7.3 psi (5 bar -0.5 bar)
[*1.10] [~1.34]
Permitt. operating pressure 580 psi (40 bar) *28 ~34
*When presented as a pressure followed by a negative (ex 29 psi -4.4 psi), the 4.4 is the lower tolerance. This is not to be interpreted as a range (ex 4.4 - 29 psi).
The range in this instance would be 24.6 - 29 psi. Indicators are not field adjustable.
VR x D.x /-LED
Type of indication Visual indicator & electrical switch
Weight 0.79 lbs (360 g)
29 psi -4.4 psi (2 bar -0.3 bar)
Trip Pressure / Range*
73 psi -7.3 psi (5 bar -0.5 bar) [*1.10] [~1.34]
*28 ~34
Permitt. operating pressure 580 psi (40 bar)
Permitt. temperature range -22˚F to 212˚F (-30°C to 100°C)
Thread G 1/2
Max. torque Refer to end of section G
[~4.23] [~3.07]
Switching type N/O contact ~107.5 ~78
VMF x E.x
Type of indication Visual-analog, scale indication
[ø1.97]
Weight 0.12 lbs (54 g) ø50
VR x E.x
Type of indication Visual-analog, scale indication [ø1.97]
Weight 0.28 lbs (125 g) ø50
VMF x ES.x
Type of indication Visual-analog, scale indication
[1.18]
Weight 0.12 lbs (54 g) 30
Switching type –
Max. switching voltage – [0.39]
G 1/8
10
Electrical connection – *12
VMF x F.x
Type of indication Electrical switch [ø1.26]
ø32
Weight 0.15 lbs (70 g)
29 psi ±4.4 psi
Trip Pressure / Range
(2 bar ±0.3 bar)
Permitt. operating pressure 580 psi (40 bar)
Permitt. temperature range -22˚F to 212˚F (-30°C to 100°C)
Thread G 1/8
Max. torque Refer to end of section G [~3.44]
Switching type N/O contact (N/C as an option) ~87.5
VR x F.x
Type of indication Electrical switch [ø1.26]
ø32
Weight 0.29 lbs (130 g)
29 psi ±4.4 psi
Trip Pressure / Range
(2 bar ±0.3 bar)
Permitt. operating pressure 580 psi (40 bar)
Permitt. temperature range -22˚F to 212˚F (-30°C to 100°C)
Thread G 1/2
Max. torque Refer to end of section G
[~4.11]
Switching type N/O contact (N/C as an option) ~104.5
VR x GC.x
Electronic / Analog
(4-20 mA or 1-10 V)
Type of indication 1 electrical switching contact at 75%
and at 100% of pressure setting
Analog signal up to 20% of pressure
setting constant 4mA or 1 V Plug can be
repositioned in steps of 52º
Weight 0.75 lbs (340 g)
Trip Pressure / Range* 29 psi -10% (2 bar -10%)
Permitt. operating pressure 102 psi (7 bar)
[2.36]
Permitt. temperature range -22˚F to 176˚F (-30°C to 80°C) 60
Thread G 1/2
[~5.02] [~6.00]
Max. torque Refer to end of section G ~127.5 ~152.5
N/C or N/O, electronic, PNP
Switching type positive switching (factory setting) HEX 30
Max. switching voltage Operating voltage 20-30 V DC
Electrical connection 7 pole plug to DIN 43651, PG 11
Max. switching voltage at G1/2 [0.47]
12 W 12
resistive load [ø1.81]
ø46
Switching capacity Ohmic 0.4 A at 30 V =
IP 65 (only if the connector is wired
Protection class to DIN 40050 and fitted correctly)
Order example VR 2 GC.0 /-LED-SQ-123
VMF x J.x
Type of indication Electrical switch
Weight 0.66 lbs (300 g)
29 psi -4.4 psi (2 bar -0.3 bar) [~ 1.77]
Trip Pressure / Range* 73 psi -7.3 psi (5 bar -0.5 bar) ~ 45
[ 1.06]
Permitt. operating pressure 580 psi (40 bar) 27
*When presented as a pressure followed by a negative (ex 29 psi -4.4 psi), the 4.4 is the lower tolerance. This is not to be interpreted as a range (ex 4.4 - 29 psi).
The range in this instance would be 24.6 - 29 psi. Indicators are not field adjustable.
VMF x J4.x
Type of indication Electrical switch
Weight 0.60 lbs (270 g)
[~ 1.59]
29 psi -4.4 psi (2 bar -0.3 bar) ~ 40.5
Trip Pressure / Range* [*1.06]
73 psi -7.3 psi (5 bar -0.5 bar) *27
Permitt. operating pressure 580 psi (40 bar)
Permitt. temperature range -13˚F to 185˚F (-25˚C to 85˚C)
Thread G1/8
Max. torque Refer to end of section G
Switching type N/C or N/O (change-over contacts) [~ 3.76] [~ 2.58]
~ 95.5 ~ 65.5
Max. switching voltage 230V
12mm (Micro) connector (4 PIN);
Electrical connection HEX 27
A Female connector to DIN 43650
1 Max. switching voltage at 250W=
2 resistive load 300VA~
p 2 Ohmic 6A at 24V=
1 Switching capacity
3 Ohmic 0.03 to 6A at max. 230V~ [0.39]
3 G 1/8
4 IP 65 (only if the connector is wired 10
Protection class to DIN 40050
and fitted correctly)
B Order example VMF 2 J4.1
VR x J4.x
Type of indication Electrical switch
[~ 1.59]
Weight 0.75 lbs (340 g) ~ 40.5
[1.06]
29 psi -4.4 psi (2 bar -0.3 bar) 27
Trip Pressure / Range*
73 psi -7.3 psi (5 bar -0.5 bar)
Permitt. operating pressure 580 psi (40 bar)
Permitt. temperature range -13˚F to 185˚F (-25˚C to 85˚C)
Thread G1/2
Max. torque Refer to end of section G
[~ 4.04] [~ 3.05]
Switching type N/C or N/O (change-over contacts) ~ 102.5 ~ 77.5
Max. switching voltage 230V
12mm (Micro) connector (4 PIN);
Electrical connection
A Female connector to DIN 43650
1 Max. switching voltage at 250W= HEX 19
2 resistive load 300VA~
p 2
1 Ohmic 6A at 24V=
3 Switching capacity Ohmic 0.03 to 6A at max. 230V~
3
4 IP 65 (only if the connector is wired
Protection class to DIN 40050 [0.55]
and fitted correctly) 14 G 1/2
B Order example VR 2 J4.1
*When presented as a pressure followed by a negative (ex 29 psi -4.4 psi), the 4.4 is the lower tolerance. This is not to be interpreted as a range (ex 4.4 - 29 psi).
The range in this instance would be 24.6 - 29 psi. Indicators are not field adjustable.
VR x LE.x
Visual (red pin) & electrical switch
Type of indication [~3.12]
(100% activation) ~79
Weight 0.32 lbs (143 g)
Trip Pressure / Range* 29 psi -2.9 psi (2 bar -0.2 bar)
Permitt. operating pressure 102 psi (7 bar)
[~1.34]
Permitt. temperature range -22˚F to 212˚F (-30°C to 100°C) ~34
VMF x LZ.x
Visual (red pin) & electrical switch
Type of indication
(75% & 100% activation)
Weight 0.51 lbs (230 g)
[~4.86]
Trip Pressure / Range* 29 psi -2.9 psi (2 bar -0.2 bar) ~123
*When presented as a pressure followed by a negative (ex 29 psi -4.4 psi), the 4.4 is the lower tolerance. This is not to be interpreted as a range (ex 4.4 - 29 psi).
The range in this instance would be 24.6 - 29 psi. Indicators are not field adjustable.
VR x LZ.x /-DB
Visual (red pin) & electrical switch
Type of indication (75% & 100% activation). 3 LEDs
(grn=power, yel=75%, red=100%)
[~3.39]
Weight 0.42 lbs (190 g) ~86 PG 11
*When presented as a pressure followed by a negative (ex 29 psi -4.4 psi), the 4.4 is the lower tolerance. This is not to be interpreted as a range (ex 4.4 - 29 psi).
The range in this instance would be 24.6 - 29 psi. Indicators are not field adjustable.
4 [0.39]
Ohmic 1 A at 15 V = 10
+ Switching capacity
P 2 Ohmic 1 A at 15 V ~ G 1/8 [0.47]
12
Yellow
IP 65 (only if the connector is wired
3 Protection class to DIN 40050
Switch
Warning Green and fitted correctly)
75% 1
Order example VMF 2 LZ.1 /-CN
VR x LZ.x /-CN
Visual (red pin) & electrical switch
Type of indication (75% & 100% activation). 3 LEDs
(grn=pwr, yel=75%, red=100%)
[~3.39]
Weight 0.42 lbs (190 g) ~86 PG 11
*When presented as a pressure followed by a negative (ex 29 psi -4.4 psi), the 4.4 is the lower tolerance. This is not to be interpreted as a range (ex 4.4 - 29 psi).
The range in this instance would be 24.6 - 29 psi. Indicators are not field adjustable.
VR x LZ.x /-AV
Visual (red pin) & electrical switch
Type of indication
(75% & 100% activation)
Weight 0.32 lbs (145 g)
29 psi (or 36 psi) -10% [2.87]
Trip Pressure / Range
2 bar (or 2.5 bar) -10% 73
[*1.38]
Permitt. operating pressure 102 psi (7 bar) *35
Switch
Warning
75%
Order example VMF 2 LZ.1 /-D4C
VR x LZ.x /-D4C
Electrical switch (75% & 100%
activation) w/30˚C thermal lockout.
Type of indication
4 LEDs (grn=pwr, blue=
below 86˚F, yel=75%, red=100%)
Weight 0.45 lbs (205 g) [1.65]
42
Trip Pressure / Range 36 psi -10% (2.5 bar -10%)
Permitt. operating pressure 102 psi (7 bar)
[~2.72]
Permitt. temperature range 14˚F to 212˚F (-10°C to 100°C) ~69
[2.09]
Thread G 1/2 ~53
+24V 0V V A-
Max. torque Refer to end of section G
M12x1
1 3 4 2 Switching type N/O (75%), N/C (100%)
HEX 30 [~3.28]
Max. switching voltage 24 V [~1.48] ~83
Grn Yel Blue Red
~37.5
Electrical connection Male connection M12 x 1 LEDs [1.02]
26
Max. switching voltage at 15 W =
Schematic with
resistive load max. 15 VA ~ G 1/2
Temperature [0.47]
switch activated
Ohmic 1 A at 15 V = 12
Switching capacity
(<30˚C)
Switch
Ohmic 1 A at 15 V ~
Alarm
Switch
Warning
75%
Order example VR 2 LZ.1 /-D4C
M21x1
Switching type N/O (75%), N/C (100%)
[~ 2.80]
Max. switching voltage 24 V
~ 71
100% alarm
2
Electrical connection Male connection M12 x 1
[1.48]
P
37.5
LEDs
4 Max. switching voltage at 15 W = HEX 30
red resistive load max. 15 VA ~
P 1 +24v Ohmic 1 A at 15 V =
yellow Switching capacity
green Ohmic 1 A at 15 V ~ [0.47]
G 1/2
3 0v 12
Protection class to DIN 40050 IP 65
75% warning
VD x B.x
Visual, red/green band
Type of indication [ø1.06]
automatic reset
ø27
Weight 0.24 lbs (110 g)
29 psi -10% (2 bar -10%)
Trip Pressure / Range 73 psi -10% (5 bar -10%)
116 psi ±10% (8 bar ±10%)
Permitt. operating pressure 6000 psi 420 bar
Permitt. temperature range -22˚F to 212˚F (-30°C to 100°C)
Thread G 1/2
[~2.50]
Max. torque Refer to end of section G *27
~63.5
Switching type -
Max. switching voltage -
Electrical connection - [1.06]
27
Max. switching voltage at
-
resistive load
Switching capacity -
Protection class to DIN 40050 - G 1/2
Order example VD 5 B.1
VM x BM.x
Visual, red/green band
Type of indication
manual reset
Weight 0.12 lbs (55 g) [ø1.06] [0.20]
ø27 5 Stroke
29 psi -10% (2 bar -10%)
Trip Pressure / Range 73 psi -10% (5 bar -10%)
116 psi ±10% (8 bar ±10%)
Permitt. operating pressure 3000 psi (210 bar)
Permitt. temperature range -22˚F to 212˚F (-30°C to 100°C)
Thread G 1/2
Max. torque Refer to end of section G [~2.72]
HEX 30 ~69
Switching type -
Max. switching voltage -
[1.06]
Electrical connection -
27
Max. switching voltage at
-
resistive load
Switching capacity -
G 1/2
Protection class to DIN 40050 -
Order example VM 5 BM.1
VM x C.x
Type of indication Electrical switch
Weight 0.26 lbs (120 g) [~1.33]
~34
29 psi -10% (2 bar -10%) [*1.09]
Trip Pressure / Range 73 psi -10% (5 bar -10%) *28
116 psi ±10% (8 bar ±10%) M20x1.5
Permitt. operating pressure 3000 psi (210 bar)
Permitt. temperature range -22˚F to 212˚F (-30°C to 100°C)
Thread G 1/2
Max. torque Refer to end of section G [~2.63]
*30
~67
Switching type N/C or N/O (change-over contacts) [~4.15]
~106
Max. switching voltage 230 V
Male connection M20
Electrical connection
Female connector to DIN 43650
Max. switching voltage at 60 W =
resistive load 100 VA ~ [1.06]
27
Ohmic 3 A at 24 V =
Switching capacity*
Ohmic 0.03 to 5 A at max. 230 V ~
IP 65 (only if the connector is wired
Protection class to DIN 40050 G 1/2
and fitted correctly)
Order example VM 5 C.0
VD x C.x
Type of indication Electrical switch
[~1.33]
Weight 0.49 lbs (220 g) ~34
[*1.09]
29 psi -10% (2 bar -10%) *28
Trip Pressure / Range 73 psi -10% (5 bar -10%)
116 psi ±10% (8 bar ±10%) M20x1.5
Permitt. operating pressure 6000 psi (420 bar)
Permitt. temperature range -22˚F to 212˚F (-30°C to 100°C)
Thread G 1/2
Max. torque Refer to end of section G
*30 [~2.63]
Switching type N/C or N/O (change-over contacts) [~4.15]
~67
~105.5
Max. switching voltage 230 V
Male connection M20
Electrical connection
Female connector to DIN 43650
Max. switching voltage at 60 W =
resistive load 100 VA ~ [1.06]
Ohmic 3 A at 24 V = 27
Switching capacity*
Ohmic 0.03 to 5 A at max. 230 V ~
IP 65 (only if the connector is wired
Protection class to DIN 40050
and fitted correctly) G 1/2
Order example VD 5 C.0
*Required amperage > 20 mA; for lower amperages, order “-SO135” indicators (see Supplementary Details in the Model Code).
VD x D.x/-L…
Type of indication Visual indicator & electrical switch
[~1.34]
Weight 0.55 lbs (250 g) ~34
[*1.10]
29 psi -10% (2 bar -10%) *28
Trip Pressure / Range 73 psi -10% (5 bar -10%)
116 psi ±10% (8 bar ±10%) M20x1.5
Permitt. operating pressure 6000 psi (420 bar)
Permitt. temperature range -22˚F to 212˚F (-30°C to 100°C)
Thread G 1/2
Max. torque Refer to end of section G
*30 [~2.65]
Switching type N/C or N/O (change-over contacts) [~4.32] ~67
~110
24, 48, 115, 230 V
Max. switching voltage
(depending on the type of light insert)
1 p
Male connection M20
2 Electrical connection
3
Female connector to DIN 43650
Max. switching voltage at 60 W =
resistive load 100 VA ~ [1.06]
R
Ohmic 3 A at 24 V = 27
Switching capacity*
Ohmic 0.03 to 5 A at max. 230 V ~
Connection
IP 65 (only if the connector is wired
block
5 Protection class to DIN 40050
and fitted correctly)
G 1/2
Order example VD 5 D.0 /-L24
VM x D.x/-LED
Type of indication Visual indicator & electrical switch
[~1.34]
Weight 0.33 lbs (150 g) ~34
29 psi -10% (2 bar -10%) [*1.10]
*28
Trip Pressure / Range 73 psi -10% (5 bar -10%)
116 psi ±10% (8 bar ±10%) M20x1.5
VD x GC.x
Electronic / Analog
(4-20 mA or 1-10 V)
Type of indication 1 switch contact at 75% and
at 100% trip pressure
Weight 0.88 lbs (400 g) Plug can be repositioned
in steps of 52º
29 psi -10% (2 bar -10%)
Trip Pressure / Range 73 psi -10% (5 bar -10%)
116 psi -10% (8 bar -10%)
Permitt. operating pressure 6000 psi (420 bar)
[2.36]
Permitt. temperature range -22˚F to 176˚F (-30°C to 80°C) 60
VL x GW.x
Electronic / Analog, (4-20 mA)
Type of indication 1 switch contact at 75% and
at 100% trip pressure [ø1.81]
ø46
Weight 0.35 lbs (157 g)
M12x1
29 psi ±5% 44 psi ±5% 73 psi ±5%
Pressure setting (100%) (2 bar ±5%) (3 bar ±5%) (5 bar ±5%)
0 - 73 psi 0 - 73 psi 0 - 116 psi
Indication range ∆p (0 - 5 bar) (0 - 5 bar) (0 - 8 bar) [0.46]
11.6
Indication range (p before filter) 363 psi (25 bar)
El. switch, PNP positive switching
Switching type (output ∆p)
N/C or N/O contacts (factory set.)
Output load 400 mA
Max. switching 20 - 30V DC
operating voltage [3.58]
Analog outputs 4 - 20 mA (max. load resistance 91
(p before filter & ∆p) 600Ω) HEX 27
Electrical connection M12x1/8 pole
Protection class to DIN 40050 IP 65
Permitt. operating pressure 25 bar [1.06]
27
Permitt. temperature range -40˚F to 185˚F (-40°C to 85°C)
Thread G 1/2
Max. torque Refer to end of section G G 1/2
VD x J.x
Type of indication Electrical switch
Weight 0.55 lbs (250 g) [~ 1.77]
29 psi -10% (2 bar -10%) ~ 45
[*1.06]
Trip Pressure / Range 73 psi -10% (5 bar -10%) *27
116 psi ±10% (8 bar ±10%)
Permitt. operating pressure 6000 psi (420 bar)
Permitt. temperature range -13˚F to 185˚F (-25˚C to 85˚C)
Thread G 1/2
Max. torque Refer to end of section G HEX 30 [~ 2.38]
[~ 3.96] ~ 60.5
Switching type N/C or N/O (change-over contacts) ~ 100.5
Max. switching voltage 230V
7/8” (Mini) connector (5 PIN);
A Electrical connection
Female connector to DIN 43650
2 Max. switching voltage at 60W=
p 2 RED [1.06]
1 WHITE resistive load 100VA~ 27
1 Ohmic 3A at 24V=
3 ORANGE Switching capacity
4 Ohmic 0.03 to 5A at max. 230V~
GREEN 3 Protection class to DIN 40050 IP 65 (only if the connector is wired G 1/2
B BLACK and fitted correctly)
5
Order example VD 5 J.1
VM x J4.x
Type of indication Electrical switch
Weight 0.26 lbs (120 g) ~ [1.59]
~ 40.5
29 psi -10% (2 bar -10%) [*1.06]
*27
Trip Pressure / Range 73 psi -10% (5 bar -10%)
116 psi ±10% (8 bar ±10%)
Permitt. operating pressure 3000 psi (210 bar)
Permitt. temperature range -13˚F to 185˚F (-25˚C to 85˚C)
Thread G 1/2
Max. torque Refer to end of section G [~ 3.96] HEX 30 [~ 2.46]
~ 100.5 ~ 62.5
Switching type N/C or N/O (change-over contacts)
Max. switching voltage 230V
12mm (Micro) connector (4 PIN);
A Electrical connection
1 Female connector to DIN 43650
2 Max. switching voltage at 60W=
p 2 [1.06]
1 resistive load 100VA~ 27
3 Ohmic 3A at 24V=
3 Switching capacity
4 Ohmic 0.03 to 5A at max. 230V~
IP 65 (only if the connector is wired
Protection class to DIN 40050 G 1/2
and fitted correctly)
B
Order example VM 5 J4.1
VD x LE.x
Visual (red pin) & electrical switch
Type of indication
(100% activation) [~3.12]
~79
Weight 0.44 lbs (198 g)
29 psi -10% (2 bar -10%)
Trip Pressure / Range 73 psi -10% (5 bar -10%)
116 psi (8 bar) - Consult HYDAC
Permitt. operating pressure 6000 psi (420 bar) [~1.34]
~34
Permitt. temperature range 14˚F to 212˚F (-10°C to 100°C)
[1.38]
Thread G 1/2 35 M20x1.5
VD x LZ.x
Visual (red pin) & electrical switch
Type of indication
(75% & 100% activation)
Weight 0.53 lbs (240 g)
29 psi -10% (2 bar -10%) [~4.86]
~123
Trip Pressure / Range 73 psi -10% (5 bar -10%)
116 psi (8 bar) - Consult HYDAC
Permitt. operating pressure 6000 psi (420 bar)
[~1.34]
Permitt. temperature range 14˚F to 212˚F (-10°C to 100°C) ~34
VD x LZ.x /-CN
Visual (red pin) & electrical switch
Type of indication (75% & 100% activation). 3 LEDs
(grn=pwr, yel=75%, red=100%)
Weight 0.54 lbs (245 g) [~3.39] PG 11
~86
29 psi -10% (2 bar -10%)
Trip Pressure / Range 73 psi -10% (5 bar -10%)
116 psi (8 bar) - Consult HYDAC [2.35]
Permitt. operating pressure 6000 psi (420 bar) max. 60
VD x LZ.x /-BO
Visual (red pin) & electrical switch
Type of indication (75% & 100% activation)
Weight 0.43 lbs (197 g) [2.87]
29 psi -10% (2 bar -10%) 73
Trip Pressure / Range 73 psi -10% (5 bar -10%) [*1.38]
116 psi (8 bar) - Consult HYDAC *35
4
Electrical connection Male connection M12 x1
[1.06]
Max. switching voltage at 15 W = 27
P 1 resistive load max. 15 VA ~
Ohmic 1 A at 15 V =
3 Switching capacity Ohmic 1 A at 15 V ~ G 1/2
Switch:
Warning 75% Protection class to DIN 40050 IP 65
B Order example VD 5 LZ.1 /-AV
VD x LZ.x /-D4C
Electrical switch (75% & 100%
activation) w/30˚C thermal lockout.
Type of indication
4 LEDs (grn=pwr, blue=
below 86˚F, yel=75%, red=100%)
Weight 0.56 lbs (256 g) [1.65]
42
29 psi -10% (2 bar -10%)
Trip Pressure / Range 73 psi -10% (5 bar -10%)
116 psi (8 bar) - Consult HYDAC
Permitt. operating pressure 6000 psi (420 bar)
[2.72]
Permitt. temperature range 14˚F to 212˚F (-10°C to 100°C) ~69 [2.13]
+24V 0V V A-
54
Thread G 1/2
1 3 4 2
Max. torque Refer to end of section G
M12x1
Switching type N/O (75%), N/C (100%) [2.40]
Grn Yel Blue Red
~61
Max. switching voltage 24 V
[1.06]
~27
Electrical connection Male connection M12 x1 HEX 30
Schematic with
Max. switching voltage at 15 W =
max. 15 VA ~ LEDs [1.06]
Temperature
switch activated resistive load 27
(<30˚C)
Ohmic 1 A at 15 V =
Switching capacity
Switch Ohmic 1 A at 15 V ~
Alarm
100% G 1/2
Switch
Protection class to DIN 40050 IP 65
Warning
VD x LZ.x /-BO-LED
Electrical switch (75% & 100%
Type of indication activation). 3 LEDs (grn=pwr,
yel=75%, red=100%)
Weight 0.55 lbs (250 g) [1.65]
42
29 psi -10% (2 bar -10%)
Trip Pressure / Range 73 psi -10% (5 bar -10%)
116 psi (8 bar) - Consult HYDAC
Permitt. operating pressure 6000 psi (420 bar)
[2.72]
Permitt. temperature range 14˚F to 212˚F (-10°C to 100°C) ~69 [2.13]
Thread G 1/2 54
VR x FD.x
Type of indication Electrical switch
[ø0.98]
Weight 0.20 lbs (90 g) ø25
Ohmic 2.5 A at 24 V =
Switching capacity
Ohmic 1 A at 220 V ~
IP 67 (only if the connector is wired
Protection class to DIN 40050 [0.55]
and fitted correctly) 14
G 1/2
Order example VR 2 FD.0 /-2M0
VM x CD.x
Type of indication Electrical switch
Weight 0.22 lbs (100 g)
29 psi -10% (2 bar -10%)
Trip Pressure / Range 73 psi -10% (5 bar -10%)
116 psi ±10% (8 bar ±10%)
Permitt. operating pressure 3000 psi (210 bar)
HEX 30 [~2.73]
Permitt. temperature range -22˚F to 212˚F (-30°C to 100°C) ~69
[1.87]
Thread G 1/2 47.5
VD x CD.x
Type of indication Electrical switch
Weight 0.43 lbs (195 g)
29 psi -10% (2 bar -10%)
Trip Pressure / Range 73 psi -10% (5 bar -10%)
116 psi ±10% (8 bar ±10%)
Permitt. operating pressure 6000 psi (420 bar)
HEX 30 [~2.73]
Permitt. temperature range -22˚F to 212˚F (-30°C to 100°C) ~69
[1.87]
Thread G 1/2 47.5
B…CMF*
Type of indication Single pole (ground switching)
Weight 0.05 lbs (24 g) [0.88]
22.4
Trip Pressure / Range 44 psi +6 psi (3 bar +0.4 bar)
Permitt. operating pressure 3000 psi (210 bar)
Permitt. temperature range 22˚F to 200˚F (-30°C to 93°C)
#8-32 thread post
connector
Thread SAE-8 differential port
Max. torque Refer to end of section G [0.90]
22.9
Switching type N/O
Max. switching voltage –
Electrical connection #8 - 32 threaded post
Max. switching voltage at
–
resistive load
Switching capacity ohmic 200MA at 36VDC
Chassis Protection class to DIN 40050 Terminals IP00
Ground
3/4"-16UNF-2B
Order example B3420CMF.0
B…LEMF*
Type of indication Visual indicator & electric switch
[0.88]
Weight 0.18 lbs (80 g) 22.4
[*1.18]
Trip Pressure / Range 44 psi +6 psi (3 bar +0.4 bar) *30
Permitt. operating pressure 3000 psi (210 bar)
Permitt. temperature range 22˚F to 200˚F (-30°C to 93°C) [1.50]
38.1
Thread SAE-8 differential port
Max. torque Refer to end of section G
Switching type N/O or N/C (change-over contacts)
[1.80]
Max. switching voltage – 45.7
Red Pop-up
A Electrical connection Female connector to DIN 43650 Indicator
Max. switching voltage at
3 –
p resistive load
ohmic 5A at 125/250VAC,
Switching capacity
1 5A at 24VDC
Protection class to DIN 40050 IP60
B 2
3/4"-16UNF-2B
Order example B3420LEMF.0
*This clogging indicator is for use with the MF/MFD/MFDS Series only.
VD x C.x /-2GEXDIIC
Type of indication Electrical switch
Weight 1.32 lbs (600 g)
29 psi -10% (2 bar -10%)
Trip Pressure / Range 73 psi -10% (5 bar -10%)
116 psi ±10% (8 bar ±10%)
Permitt. operating pressure 6000 psi (420 bar)
-4˚F to 140˚F (-20°C to 60°C)
Permitt. temperature range HEX 24
setting (media temp. max. 75° C)
Thread G 1/2 [~4.53]
~115
Max. torque Refer to end of section G [~3.48]
~89
Switching type Change-over [2.34]
59.5
Max. switching voltage 250 V
HEX 30 [0.79]
Electrical connection Cable connection 20
Max. switching voltage at 60 W =
resistive load 100 VA ~ [1.06]
27
ohmic 3 A at 24 V =
Switching capacity
ohmic 0.03 A to 5 A at 250 V ~
G1/2
Protection class to DIN 40050 IP 66
[ø1.38]
ATEX designation ø35
II 2G Ex d IIC T6
Order example VD 2 C.1 /-2GEXDIIC
Notes: 1. Old style indicators for filters HF2P / HF3P / HF4P - pre 2008 (Example Model Code: B2210BHF), contact HYDAC for further information.
2. VMF indicators of type B, LE, LZ, and C I-EX2G, must include “V” at the end of the Model Code if Fluorocarbon elastomer (FKM) seals are required. All
other VMF indicators come with Fluorocarbon elastomer (FKM) seals as a standard (no Supplementary Detail required).
SECTION
G 1/2
SECTION
3/4-16UNF-2A
Adapter - Static - G 1/2” to G 1/8” Adapter - Static - G 1/8” to G 1/2” Pipe Connection Block - SAE-4 Ports
(Part No. 319004 w/NBR seal) (Part No. 318740) to G1/2 Differential Indicator Port
(Part No. 02080588)
HEX 19 [2.00]
HEX 36 50.8
[0.79 -0.04]
20 -1
[1.50]
38.1
[2.36]
60
[1.50]
G 1/2 G 1/2 38
[1.26]
[1.69] 32
[0.28]
43 7
G 1/2
Dual Indicator Block- Differential - G 1/2 Indicator Port to 2 x G 1/2 Indicator Ports
(Part No. 00318732 with NBR seals)
[3.43]
87
[1.97]
50 [1.57]
G 1/2 G 1/2 40
[2.36]
60
[3.43]
87 [0.79]
20
G 1/2
APPLICABLE
UF/UFJ sealant.
A 37 37 24
B/BM 11 11 11
C/CM
D
37 37 24
E/ES
F/FA/FD/FF/FJ/FM/FS
Elastomeric seal
VR GC 7.5
11 11 11 included.
LE/LEC/LEM/LZ
K
R/RS
UC/UCM 37 37 24
UE/UED
UF/UFJ
C/CM
D
E/ES
K
Elastomeric seal
VRD F/FA/FD/FF/FJ/FM/FS 37 37 24 7.5
included.
R/RS
UC/UCM
UE/UED
UF/UFJ
A 37 37 24 7.5
B/BM
NOT
C/CA/CC/CD/CJ/CM/CS/CW
APPLICABLE
D
NOT
B/BM (W Option) APPLICABLE
74 74
C/CA/CC/CD/CJ/CM/CS/CW Elastomeric seal
VD
(W Option) included.
DIFFERENTIAL INDICATORS
D (W Option)
24
GC
LE/LEC/LEM/LZ
7.5
MB/MBM 37 37
MC/MCD/MCJ
NOT
BF 0.5 0.5 0.5 Elastomeric seal
VL APPLICABLE
included.
GW 24 24 24 7.5
B/BM
C/CA/CC/CD/CJ/CM/CS/CW
D
Elastomeric seal
VM GM 24 24 24 7.5
included.
M
MB/MBM
MC/MCD/MCJ
B
Elastomeric seal
B…MF LE N/A N/A 24 N/A
included.
C
This drawing is PROPRIETARY. Distribution, reproduction or disclosure of information pertaining to this drawing to any party other than those directly
working with HYDAC is strictly prohibited without the written consent of HYDAC.