Sunteți pe pagina 1din 8

AIRCRAFT LIGHTING SYSTEM TRAINER

This Trainer used for demonstration Lights on aircarft, both

internal and external light. To known the power source to drive

these lamps, this trainer copmleted with voltmeter to known the

voltage use and Ampere meter to drawn the Current Consumption

for each lamp. This Ampere meter not exactly drawn the current

consumption. But for simulated how much current need to drive

each lamp.

To Simulate Aircraft Lighting in this panel do the steps as


follows:

1. ANTI COLLITION LIGHT

To simulate Anti Collition Light do the steps as follws:

 Ensure all switch on the panel on “ OFF ” position.

 Connect red jumper on RED JACK TP 1 to RED JACK on JP1.

 Connect black jumper On BLACK JACK TP 1 to one of four

BLACK JACK on panel.

 Make sure the connections.

 Turn the power switch marked SW 1 to “ ON ”.

 Anti Collition Light lamp will light flashing.

1
 After complated the experiment, turn the power switch

marked SW 1 to “ OFF ”.

Note :

Observe current consumption on Ampere Meter, current

consumption becomes high when the lamp light. Observe too the

current comsumption on each lamp on yhis trainer.

2
2. POSITION LIGHT

To simulate Position Light do the steps as follows :

 Ensure all switch on the panel on “ OFF ” position.

 Connect red jumper on RED JACK TP 2 to RED JACK on

JP2.

 Connect black jumper On BLACK JACK TP 2 to one of four

BLACK JACK on panel.

 Make sure the connections.

 Turn the power switch marked SW 2 to “ ON ”..lsl

 Position Light lamp will light.

 After completed the experiment, turn power switch

marked SW 2 to “ OFF ”.

3
3. UTILITY LIGHT

To simulate Utility Light do the steps as follows :

 Ensure all switch on the panel on “ OFF ” position.

 Connect red jumper on RED JACK TP 3 to RED JACK on

JP3.

 Connect black jumper On BLACK JACK TP 3 to one of four

BLACK JACK on panel.

 Make sure the connections.

 Turn the power switch marked SW 3 to “ ON ”.

 Utility Light lamp will light.

 After completed the experiment, turn power switch

marked SW 3 to “ OFF ”.

4
4. SPOT LIGHT

To simulate Spot Light do the steps as follows :

 Ensure all switch on the panel on “ OFF ” position.

 Connect red jumper on RED JACK TP 4 to RED JACK on

JP4.

 Connect black jumper On BLACK JACK TP 4 to one of four

BLACK JACK on panel.

 Make sure the connections.

 Turn the power switch marked SW 4 to “ ON ”.

 Spot Light lamp will light.

 After completed the experiment, turn power switch marked

SW 4 to “ OFF ”.

5
5. DOME LIGHT

The Dome Light Unit has two lamps, red and white.

To simulate red Light do the steps as follows :

 Ensure all switch on the panel on “ OFF ” position.

 Connect red jumper on RED JACK marked RED LAMP TP 5 to

RED JACK on JP 5.

 Connect black jumper On BLACK JACK TP 5 to one of four

BLACK JACK on panel.

 Make sure the connections.

 Turn the power switch marked SW 5 to “ ON ”.

 Red Dome Light lamp will light.

 After completed the experiment, turn power switch

marked SW 5 to “ OFF ”.

To simulate white Light do the steps as follows :

 Ensure all switch on the panel on “ OFF ” position.

 Connect red jumper on RED JACK marked white LAMP TP 5

to RED JACK on JP 5.

 Connect black jumper On BLACK JACK TP 4 to one of four

BLACK JACK on panel.

 Make sure the connections.

 Turn the power switch marked SW 5 to “ ON ”.

6
 Red Dome Light lamp will light.

 After completed the experiment, turn power switch

marked SW 5 to “ OFF ”.

7
6. LANDING LIGHT

The simulate Landing Light do the steps as follows:

 Ensure all switch on the panel on “ OFF ” position.

 Connect JACK marked H on TP 6 to RED JACK and JP 6

with Special Red Supplied Cable (this lamp uses

aprrox. 25 Ampere DC Current).

 Connect JACK marked I on TP 6 to one of four BLACK

JACK with Supplied Cable.

 Make sure the connections.

 Turn the power switch marked SW 6 to “ ON ”.

 Turn the power switch marked SW 9 to “ ON ”.

 Landing Light lamp will light.

 To extend or retract the lamp, press SW 8 to “EXTEND”

or “RETRACT”. The lamp can retract or extend while

lamp ON or OFF.

 After completed the experiment, turn power switch

marked SW 7 to “ OFF ”.

S-ar putea să vă placă și