Documente Academic
Documente Profesional
Documente Cultură
1
GENERAL INFORMATION
Warnings and Note It must be studied before neither personal safety nor CE Marking
working with the tool. equipment safety will be
WARNING: A “warning” jeopardized. The tool complies with the
indicates a definite risk Intended use of this Machinery Directive
of equipment damage or manual Intellectual property 98/37/EC and 2006/42/EC
danger to personnel.
This manual is intended All rights retained. No part
Failure to observe and For machines containing
for use by field service, of this document may be
follow proper procedures any hydraulic or pneumatic
engineering, installation, reproduced in any form
could result in serious or powered parts, the
operation, and repair (print, photocopy, microfilm
fatal injury to personnel, Directive 94/9/EC
personnel. Every effort has or any other procedure)
significant property loss, “Equipment and protective
been made to ensure the or be processed using an
or significant equipment systems in potentially
accuracy of the information electronic system without
damage. explosive atmospheres”
contained herein. Blohm written approval of Blohm
applies.
+ Voss Oil Tools, will not + Voss Oil Tools.
NOTE: A “note” indicates The marking is as follows:
be held liable for errors All information contained
that additional information CE Ex II 2G T5 (hydraulic
in this material, or for in this manual is based
is provided about the tools) or CE Ex II 2G T6
consequences arising from upon the latest product
current topics. (pneumatic tools).
misuse of this material. information available at
Anyone using service any time of printing.
WARNING: This technical
procedures or tools, Dependent on ongoing
documentation contains
instructions on safety, whether or not technical improvements Limited Warranty
recommended by Blohm (ISO 9001) “Blohm + Voss
installation, operation and The warranty provided will
+ Voss Oil Tools, must be Oil Tools” reserves the
maintenance for theBlohm be void if the tool is either:
thoroughly satisfied that right to change the design
+ Voss Oil Tools tool . 1. Repaired or serviced
and specifications without
by a service facility
Improper / Unsafe Use announcement.
The values specified in which was not
The tool must only be authorised by
this manual represent the
used for the designated Blohm + Voss Oil
nominal values of a unit
purpose. Tools.
produced in series. Slight
When using the tool, the 2. Replacement parts
deviations in the case of
rated load must never be not manufactured by
the individual devices are
exceeded. Blohm+Voss Oil Tools
possible.
are used.
NOTE: In the event of 3. Modifications were
problems that cannot be made to the tool which
solved with the aid of this were not approved by
manual, please contact Blohm+Voss Oil Tools.
one of the addresses listed
below.
2
General safety issues
WARNING: One should WARNING: Always ensure
avoid creating ignition WARNING: Any the slip segments are
sources, like heat, as a modification to the tool labelled with the same
result of the use of the carried out without the serial number. Never use
Warning sign PN 671638
tool with other tools or approval of Blohm + Voss segments with different General warning
equipment. Oil Tools will void any numbers as they may cause
warranty. the pipe to drop due to
WARNING: Do not use the WARNING: Using the different wear patterns.
tool for any other purpose tool with damaged or worn
than given in this document parts can create serious
within its specification. incidents.
WARNING: If necessary,
a reasonable, additional
supervisor should be Warning sign PN 671641
appointed during operation. Pay attention: Risk of crushing.
3
EC-DECLARATION OF CONFORMITY
We,
Blohm + Voss Oil Tools
Hermann-Blohm-Strasse 2
20457 Hamburg
Phone:+49(0)40 3119-1139
Fax:+49(0)40 3119-3305
declare that the product
which is the subject of this declaration, is in conformity with the following standard(s) or normative documents
98/37/EC: Machinery Directive
2006/42/EC: Machinery Directive from 31 December 2009.
DIN EN ISO 12100 : Safety of machinery, part 1 and 2
DIN EN ISO 14121-1: Safety of machinery, Risk assessment
Directive 94/9/EC: Devices and protection systems for intended use in explosive areas
DIN EN 13463-1:2009-07: Non-electrical equipment for use in potentially explosive atmospheres
ISO 14693/API 7K: Specification for Drilling and Well Servicing Equipment
Marking: II 2G T6
4
CONTENTS
TABLE OF CONTENTS
TABLE OF
GENERAL INFORMATION 2 Dismantling Inspection 21
Wear data Criteria 22
Warnings and Note 2
Inspection check lists 23
DESCRIPTION
Intended use of this manual 2
Check Category I (Ongoing observation)
Intellectual property 2
24
Improper / Unsafe Use 2
Check List Category II (Daily) 24
Manufacturer & Agents World wide 2
Check List Category III (every 6 months)
CE Marking 2
25
Limited Warranty 2
Check List Category IV (every year) 25
General safety issues 3
4. DRAWINGS
EC-DECLARATION OF CONFORMITY 4
28
OPERATION
TABLE OF CONTENTS 5 RSM-Medium Rotary Slips
28
1. DESCRIPTION 8 RSX-Extra Long Rotary Slips 29
RSX-Extra Long Rotary Slips 30
Intend of use 8 RSX-Extra Long Rotary Slips 31
RSM - Medium Rotary Slips 8 LRS-Load Rated Slips 32
RSM-Medium Rotary Slips part numbers 8 LRS-Load Rated Slips 33
MAINTENANCE &
INSPECTION
RSX - Extra Long Rotary Slips 9 Drill Collar Slips 34
RSX-Extra Long Rotary Slips part numbers 9 Drill colar slips grip lenght
LRS - Load Rated Slips 10 34
LRS-Load Rated Slips part numbers 10 Drill Collar Slips 35
DCS / DCM / DCL - Multisegment Drill Collar Slips 11 CSL / CSC Casing Slips Parts 36
DCS / DCM / DCL-Multisegment Drill Collar Slips CSL Casing Slip grip length 36
part numbers 11 CSL / CSC Casing Slips Parts 37
CSL – Extra Long Casing Slips 12 CSL / CSC Casing Slips Parts 38
CSL – Extra Long Casing Slips part numbers 12
DRAWINGS
CSC – Conductor Pipe Slips 13
CSC – Conductor Pipe Slips part numbers 13
Improper / Unsafe Use 14
Temperature 14
Identification area 14
2. OPERATION
16
Operation RIH (Running in Hole) 18
Operation POOH (Pulling Out Of Hole) 18
Operation with kelly bushing (RIH) 18
Operation with kelly bushing (POOH) 18
5
6
TABLE OF MAINTENANCE &
DESCRIPTION OPERATION DRAWINGS
CONTENTS INSPECTION
DESCRIPTION
DESCRIPTION
7
1. DESCRIPTION
Intend of use
The Blohm + Voss Manual Slips are designed for use
DESCRIPTION
8
RSX - Extra Long Rotary Slips
The RSX series has 16.1/2”of insert gripping length
DESCRIPTION
which is recommended for all deep well and heavy drill
string applications. The rugged design of the Blohm
+ Voss slip assembly provides full load distribution
throughout the length of the slip and prevents
bottlenecking and gouging of the drill pipe. Blohm +
Voss slips provide maximum load carrying capacity and
a lightweight, balanced design which minimizes crew
fatigue.
Slip body size (inches) 5" 5" 5" 5.1/2" 5.1/2" 5.1/2"
API pipe size (OD, Inches) 4" 4.1/2" 5" 4.1/2" 5" 5.1/2"
Part No.: Slip complete w/inserts 83310-2 83320-2 83330-2 83410-2 83420-2 83430-2
Weight: slip complete w/inserts lb (kg) 273 (124) 262 (119) 249 (113) 267 (121) 256 (116) 245 (111)
INSERT set: part no. - Quantity 80118-54 80116-54 80117-54 80118-54 80119-54 80120-54
Weight lb (kg) 47 (21,3) 37 (16,8) 23 (10,4) 47 (21,3) 37 (16,8) 23 (10,4)
Slip body size (inches) 6.5/8" 6.5/8" 6.5/8" 7" 7" 7"
API pipe size (OD, Inches) 5.3/4" 5.7/8" 6.5/8" 6" 6.5/8" 7"
Part No.: Slip complete w/inserts 83550-2 83540-2 83520-2 83510 83520 83530
Weight: slip complete w/inserts lb (kg) 253 (114,7) 249 (113) 231 (105) 265 (120) 251 (114) 242 (110)
INSERT set: part no. - Quantity 270808-54 270708-54 270109-54 80118-72 80122-72 80123-72
Weight lb (kg) 41,7 (18,9) 38 (17,3) 20 (9,2) 63 (28,4) 39 (17,6) 26 (11,7)
9
LRS - Load Rated Slips
The LRS series are load rated for 750 tons and includes
DESCRIPTION
Slip body size (inches) 5.1/2" 5.1/2" 5.1/2" 6.5/8" 6.5/8" 7"
API pipe size (OD, Inches) 4.1/2" 5" 5.1/2" 5.7/8" 6.5/8" 7"
Part No.: Slip complete w/inserts 83730 83720 83710 83620-2 83610-2 83810
Weight: slip complete w/inserts lb (kg) 260 (118) 249 (113) 243 (110) 245 (111) 229 (104) 236 (107)
INSERT set: part no. - Quantity 80118-45 80119-45 80120-45 270708-45 270109-45 80123-60
Weight lb (kg) 39 (17,8) 31 (14) 20 (9) 32 (14,4) 17 (7,7) 22 (9,8)
Part No.: Load ring 83405-1 83405-1 83405-1 83405-2 83405-2 83405-3
10
DCS / DCM / DCL - Multisegment
Drill Collar Slips
DESCRIPTION
Blohm + Voss drill collar slips provide a lightweight, high
strength assembly to handle all drill collars from 3 – 14”
diameter. Three slip body types are available.
Notes:
* This size is furnished with 4 handles.
All Blohm + Voss drill collar slips haven an API taper of 4 min./ft. on the diameter.
11
CSL – Extra Long Casing Slips
Blohm + Voss type CSL casing slips are designed
DESCRIPTION
Weight, complete w/inserts lbs (kg). 196 (89) 184 (84) 166 (75) 181 (82) 192 (87) 209 (95) 245 (111) 260 (118)
Total number of segments 12 12 12 13 14 15 17 17
Total intermediate segments 10 10 10 11 12 13 15 15
Total number of hinge pins 11 11 11 12 13 14 16 16
Casing size (OD, inches) 12.3/4" 13.3/8" & 13.1/2" 13.5/8" & 14" 15" 16" 18" 18.5/8" & 18.3/4"
P/N, slip complete w/inserts 87175 87180 87195 87196 87190 87205 87200
Weight, complete w/inserts lbs (kg) 251 289 (131) 295 (134) 322 308 352 367 (167)
(114) (146) (140) (160)
Total number of segments 17 18 20 22 21 24 25
Total intermediate segments 15 16 18 20 19 12 23
Total number of hinge pins 16 17 19 21 20 23 24
Casing size (OD, inches) 20" 22" 24" 26" 28" 30" 42"
P/N, slip complete w/inserts 87210 87215 87220 87230 87235 87240 87280
Weight, complete w/inserts lbs (kg) 383 (174) 474 (215) 443 (201) 486 (220) 531 (241) 546 659
(248) (299)
Total number of segments 26 30 30 33 36 37 51
Total intermediate segments 24 28 28 31 34 35 49
Total number of hinge pins 25 29 29 32 35 36 50
Notes:
* These sizes are furnished with 4 handles.
All Blohm + Voss CSL extra long casing slips have an API taper of 4 in./ft. on the diameter.
12
CSC – Conductor Pipe Slips
Blohm + Voss type CSC Conductor Slips are designed
DESCRIPTION
to handle casing and conductor tubular in sizes from 24”
to 36”. The multi-segment design provides even load
distribution and full wrap-around gripping on all casing/
conductor sizes.
Weight, complete w/inserts lbs (kg). 262 (119) 282 (128) 302 (137) 320 (145) 379 (172)
Total number of segments 13 14 15 16 19
Total intermediate segments 11 12 13 14 17
Total number of hinge pins 24 26 28 30 36
Total number of hinge spacer 12 13 14 15 18
13
Improper / Unsafe Use
The Rotary Hand Slips must only be used for the
DESCRIPTION
designated purpose.
When using the Rotary Hand Slips, the designated load
must never be exceeded (depending on the rating).
Allslips are made from high-strength alloy steel to
provide the strongest, lightest design possible, for
maximum durability.
The identification area clearly identifies the Rotary Hand
Slip area (manufacturer, type, material, part number,
serial number, date of manufacture). It is important to
keep this information ready for the purpose of servicing
and repair work.
Temperature
Rotary Handslips
- 40° C to + 80° C *
Temperature working range ambient
- 40° F to 176° F *
* If not otherwise stated in the databook.
Identification area
14
OPERATION
OPERATIONS
15
2. OPERATION
1. The manual slips must only be used for the designated pipe size.
2. If the slips are used on larger pipe sizes, the inserts are only gripping with their outside corners and the slip
segments are not set properly around the pipe.
3. If the slips are used on smaller pipe sizes, the inserts are only gripping with their middle section and the slip
segments are not set on smaller pipe sizes, the inserts are only gripping with their middle section and the slip
segments are not set properly around the pipe. These causes could result in significant equipment and pipe
damage.
4. After the slips were used on the wrong pipe size, the slip segments and inserts could get deformations and
cracks or could break.
5. While setting the slips on the designated pipe size, pay especially attention that the slips are set properly
around the pipe and not set partially on the tool joint. These causes result in bending of the slip segments, insert
damage and in pipe damage. Pay also especially attention while setting drill collar slips on collars with recessed
OPERATION
areas.
6. If the drill collar slips are not set properly around the pipe or set partially on the upset area, it could result in
significant equipment and pipe damage.
7. In case of a wrong slip setting, raise the string and set the slip again properly around the pipe.
If slip is used with larger pipe size If slip is used with smaller pipe size
16
OPERATION
Slip properly set around the pipe Slip properly set partially on tool joint
Slip set properly around drill collar Slip set partially on upset area
17
Operation RIH (Running in Hole)
WARNING: Before commencing any operation, ensure the hand slips and insert bowl is in good condtion and
the slips are properly greased (back side only).
WARNING: In some situations, especially when the pipe load is low e.g. at the start or beginning of the trip, it
is advised to use a safety clamp as a last resort in case the pipe slips
Procedure:
1. Lower the pipe in the hole
2. Ensure the pipe has come to a full stop
3. Move the slips into the bowl around the pipe
OPERATION
4. Lower the block and ensure the hook load drops to zero.
5. Now it is safe to open the elevator and let the slips take the load
18
MAINTENANCE &
MAINTENANCE &
INSPECTION
INSPECTION
19
3. MAINTENANCE AND INSPECTION
Daily Inspection
Procedures
Locking of screws
All Screws are normally
secured by a mechanical
bolt lock or with a safety
wire. All other screws are
secured by metal adhesive
(Locktite).
20
Inspection categories acc. to API RP 8B
Category I
This category involves observing
• disassembled in a suitable-
equipped facility to the extent
Inspection
the equipment during operation necessary to permit full A thorough inspection should be
for indications of inadequate inspection of all primary-load- carried out periodically (every 3
performance. carrying components and other months) or as special circumstances
When in use, equipment shall be components that are critical may require. Before starting an
visually inspected on a daily basis to the equipment. inspection disconnect hydraulic/
for cracks, loose fits or connections, • inspected for excessive wear, pneumatic system and remove all
elongation of part, and other signs cracks, flaws and deformation. foreign materials (dirt, paint, grease
of wear, corrosion or overloading. Procedure: Oil, scale, etc.) from surface by
Any parts found to show cracks, • Corrections shall be made a suitable method. After a field
excessive wear, etc., shall be in accordance with the inspection, it is advisable to record
removed from service for further manufacturer’s recommendations. the extent of testing and testing
examination. • Prior to inspection, all foreign results. Conduct the periodic or
The equipment shall be material such as dirt, paint, grease, critical load inspection in the field by
visually inspected by a person oil, scale, etc. shall be removed the crew with the supervisor. If cracks,
knowledgeable in that equipment from the concerned parts by excessive wear etc. is recognized,
and its function. a suitable method (e.g. paint- contact Blohm + Voss Oil Tools or an
MAINTENANCE &
stripping, steam-cleaning, grit- authorized service company.
INSPECTION
Category II blasting)
This is Category I inspection plus Critical Load Inspection
further inspection for corrosion, Frequency Critical loads may occur. For example:
deformation, loose or missing
impact loads such as jarring, pulling
components, deterioration, proper
lubrication, visible external cracks, Periodic inspection on stuck pipe, etc. If critical loads
occurred unexpectedly, conduct the
and adjustment.
The recommended schedule for inspection immediately.
Category II may involve some
inspection of Hand Slips is as follows:
disassembly to access specific
Daily: I Dismantling Inspection
components and to identify
Weekly: II Generally, when the equipment
wear that exceeds the allowable
6 Monthly: III returns to base, warehouse, etc.
tolerances.
1 Year: IV Carry out the Tool inspection,
The recommended frequencies immediately. Furthermore, control it
Category III
apply for equipment in use during the prior to its being sent on the next job.
This is Category II inspection plus
specified period. • The Tool should be dismantled
further inspection, which should
The inspection frequencies are only and inspected in a suitably
include NDT of critical areas and
recommendations. The schedule of equipped facility for excessive
may involve some disassembly to
inspection heavily depends on the wear, cracks, flaws or
access specific components and
following factors: deformations.
to identify wear that exceeds the
• environment • Corrections should be
allowable tolerances.
• load cycles made in accordance with
Prior to inspection, all foreign
• regulatory requirements recommendations which can be
material such as dirt, paint, grease,
• operating time obtained from Blohm + Voss Oil
oil, scale, etc. shall be removed from
• testing Tools.
the concerned parts by a suitable
• repairs • Weldings at the castings should
method (e.g. paint-stripping, steam-
• re manufacture be done only by Blohm + Voss
cleaning, grit-blasting).
Oil Tools or an authorized
Non-periodic inspection service company in according to
Category IV
This is Category III inspection A complete, on-job, shut-down Blohm+Voss welding procedure.
plus further inspection for which inspection equivalent to the periodical • When need is shown in a field
the equipment is disassembled to Category III or Category IV should be inspection, dismantle the Tool
the extent necessary to conduct made before (if anticipated) and after and arrange an inspection in a
NDT of all primary-load-carrying critical jobs (e.g., running heavy casing suitably equipped facility.
components. / drill strings, jarring, pulling on stuck • Springs should be carefully
Equipment shall be: pipes and/or operating at extreme low visually inspected for excessive
temperatures) <-20° C (<-4° F). wear and obvious weakness.
21
Wear data Criteria
Critical Area RSM, RSX Critical Area LRS Critical Area DCS, DCM, DCL,
CSL, CSC
MAINTENANCE &
INSPECTION
Manual slip type Multisegment Drill Collar Slips Extra Long Conductor Pipe
Casing Slip Slip
DCS DCM DCL CSL CSC
(PN 84XXX) (PN 85XXX) (PN 86XXX) (PN 87XXX) (PN 88XXX)
Range 3" - 4.7/8" 4.1/2" - 7" 6.3/4" - 14" 6.5/8" - 42" 24" - 36"
Hinge Pin 80340 80350 80340
Hinge Pin Dia. A new 16 mm
Nominal Bore B 16,5 mm
Bore B new max 16,7 mm
Bore worn max. 18 mm
WARNING: Maximum Bore dimensions are only valid when the Slipsegment is in otherwise good condition, does not
have excessive wear, crack or other defects, or previous weld repair and has not been misused. This inspection criteria
can not on their own determine the overall condition of the Slipsegment and its suitability for continued use.
22
Inspection check lists
TYPE OF EQUIPMENT
SERIAL NUMBER
PART NUMBER
MAINTENANCE &
INSPECTION
SUPERVISOR
DATE OF INSPECTION
INSPECTION CATEGORY
PLACE OF INSPECTION
23
Check Category I (Ongoing observation)
Observe during operation for inadequate performance.
CHECK FOR LOOSE ITEMS, ESPECIALLY FOR (but not limited to):
DESCRIPTION CHECKED SIGNATURE
1 Hinge pins, bolts and retainers. OK
MAINTENANCE &
INSPECTION
CHECK FOR CRACKS, ELONGATION, DAMAGE AND CORROSION, ESPECIALLY FOR (but not limited to):
DESCRIPTION CHECKED SIGNATURE
1 Hinge pins, bolts, nuts. OK
2 Slip Segments. OK
Remarks
_________________________________ _______________________________
SUPERVISOR DATE
24
Check List Category III (every 6 months)
GENERAL
DESCRIPTION CHECKED SIGNATURE
1 Carry out an Category II inspection. OK
2 NDT (MPI) critical areas. Some disassembly may be needed to do so. OK
3 Check parts for wear according to allowable tolerances. OK
Remarks
MAINTENANCE &
2 OK
INSPECTION
so.
Remarks
_________________________________________________________
SUPERVISOR DATE
25
26
MAINTENANCE &
INSPECTION
DRAWINGS
DRAWINGS
27
4. DRAWINGS
28
RSX-Extra Long Rotary Slips
DRAWINGS
Item Slips Body Size (inches) 3.1/2" 4" 4.1/2"
(pn 83210-2) (pn 83220-2) (pn 83330-2)
Description Qty Part No. Part No. Part No.
1 RSX Slip segment-center 1 82111-2 82111-2 82111-2
2 RSX Slip segment-right 1 82113-2 82113-2 82113-2
3 RSX Slip segment-left 1 82112-2 82112-2 82112-2
4 Handle Intermediate 1 80230 80230 80230
Segments
5 Handle-left 1 80240 80240 80240
6 Handle-right 1 80210 80210 80210
7 Retaining ring (3.1/2"- 4.1/2") 3 80430 80430 80430
8.1 Screw 6 89127 89127 89127
8.2 Nut 6 89125 89125 89125
9.1 Washer 1 80250-2 80250-2 80250-2
9.2 Cotter pin 2 80250-3 80250-3 80250-3
9.3 Pin 1 80250-1 80250-1 80250-1
10 Dowel pin 3 755135 755135 755135
11 Hinge Pin 2 82109 82109 82109
12 Washer 2 612679 612679 612679
13 Cotter pin 2 80250-3 80250-3 80250-3
14 Stop Plate 2 82116 82116 82116
15 Insert 54 80113 80114 80115
29
RSX-Extra Long Rotary Slips
Item Slip Body Size (inches) 4" 4.1/2" 5"
(pn 83310-2) (pn 83320-2) (pn 82230-2)
Description Qty Part No. Part No. Part No.
1 RSX Slip segment-center 1 83311-2 83311-2 83311-2
2 RSX Slip segment-right 1 83312-2 83312-2 83312-2
3 RSX Slip segment-left 1 83313-2 83313-2 83313-2
4 Handle Intermediate 1 80230 80230 80230
Segments
5 Handle-left 1 80240 80240 80240
6 Handle-right 1 80210 80210 80210
7 Retaining ring (3.1/2"- 4.1/2") 3 80450-A 80450-A 80450-A
8.1 Screw 6 89127 89127 89127
8.2 Nut 6 89125 89125 89125
9.1 Washer 1 80250-2 80250-2 80250-2
9.2 Cotter pin 2 80250-3 80250-3 80250-3
9.3 Pin 1 80250-1 80250-1 80250-1
10 Dowel pin 3 755135 755135 755135
11 Hinge Pin 2 82109 82109 82109
12 Washer 2 612679 612679 612679
13 Cotter pin 2 80250-3 80250-3 80250-3
14 Stop Plate 2 82116 82116 82116
15 Insert 54 80118 80116 80117
DRAWINGS
30
RSX-Extra Long Rotary Slips
Item Slip Body Size (inches) 5.3/4" 5.7/8" 6.5/8"
(pn 83550-2) (pn 83540-2) (pn 83520-2)
Description Qty Part No. Part No. Part No.
1 RSX Slip segment-center 1 83511-2 83511-2 83511-2
2 RSX Slip segment-right 1 83512-2 83512-2 83512-2
3 RSX Slip segment-left 1 83513-2 83513-2 83513-2
4 Handle Intermediate 1 80230 80230 80230
Segments
5 Handle-left 1 80240 80240 80240
6 Handle-right 1 80210 80210 80210
7 Retaining ring (3.1/2"- 4.1/2") 3 80480-1 80480-1 80480-1
8.1 Screw 6 89127 89127 89127
8.2 Nut 6 89125 89125 89125
9.1 Washer 1 80250-2 80250-2 80250-2
9.2 Cotter pin 1 80250-3 80250-3 80250-3
9.3 Pin 1 80250-1 80250-1 80250-1
10 Dowel pin 3 755135 755135 755135
11 Hinge Pin 2 82109 82109 82109
12 Washer 2 612679 612679 612679
13 Cotter pin 2 80250-3 80250-3 80250-3
14 Stop Plate 2 82116 82116 82116
15 Insert 54 270808 270708 270109
DRAWINGS
Item Slip Body Size (inches) 6" 6.5/8" 7"
(pn 83510) (pn 83520) (pn 83530)
Description Qty Part No. Part No. Part No.
1 RSX Slip segment-center 1 83501 83501 83501
2 RSX Slip segment-right 1 83502 83502 83502
3 RSX Slip segment-left 1 83503 83503 83503
4 Handle Intermediate 1 80230 80230 80230
Segments
5 Handle-left 1 80240 80240 80240
6 Handle-right 1 80210 80210 80210
7 Retaining ring (3.1/2"- 4.1/2") 3 80540 80540 80540
8.1 Screw 6 89127 89127 89127
8.2 Nut 6 89125 89125 89125
9.1 Washer 1 80250-2 80250-2 80250-2
9.2 Cotter pin 1 80250-3 80250-3 80250-3
9.3 Pin 1 80250-1 80250-1 80250-1
10 Dowel pin 3 70752 70752 70752
11 Hinge pin 2 80330 80330 80330
12 Nut - - - -
13 Cotter pin 2 80250-3 80250-3 80250-3
14 Insert 72 80118 80122 80123
31
LRS-Load Rated Slips
DRAWINGS
32
LRS-Load Rated Slips
Item Slip Body Size (inches) 5.7/8" (pn 83620-2) 6.5/8" (pn 83610-2)
Description Qty Part No. Part No.
1 LRS Slip segment-center 1 83711 83711
2 LRS Slip segment-right 1 83712 83712
3 LRS Slip segment-left 1 83713 83713
4 Handle Intermediate 1 80230 80230
Segments
5 Handle-left 1 80240 80240
6 Handle-right 1 80210 80210
7 Retaining ring (5.1/2"- 6.5/8") 3 80480-1 80480-1
8.1 Screw 6 80501-1 80501-1
8.2 Nut 6 89125 89125
9.1 Washer 1 80250-2 80250-2
9.2 Cotter pin 1 80250-3 80250-3
9.3 Pin 1 80250-1 80250-1
10 Dowel pin 3 755135 755135
11 Hinge Pin 2 82109 82109
12 Washer 2 612679 612679
13 Cotter pin 2 80250-3 80250-3
14 Load ring 6 83405-2 83405-2
15 Screw 12 735993 735993
16 Insert 45 270708 270109
17 Stop plate 2 82116 82116
DRAWINGS
33
Drill Collar Slips
DRAWINGS
34
Drill Collar Slips
DCS DCS DCM DCM DCL
pn 84110 pn 84120 pn 85110 pn 85120 pn 86120
Item Description Qty Partno. Qty Partno. Qty Partno. Qty Partno. Qty Partno.
1 Slip segment, intermediate 5 84112 5 84112 7 85112 7 85112 9 86112
1.1 Slip segment, right end 1 84111 1 84111 1 85111 1 85111 1 86111
1.2 Slip segment, left end 1 84113 1 84113 1 85113 1 85113 1 86113
2 Hinge pin 6 80340 6 80340 8 80340 8 80340 10 80340
3 Cotter pin 6 80340-1 6 80340-1 8 80340-1 8 80340-1 10 80340-1
4 Handle right/left end segment 2 80220 2 80220 2 80220 2 80220 2 80220
5 Handle intermediate segment 1 80230 1 80230 1 80230 1 80230 1 80230
6 Handle pin assembly 3 80250 3 80250 3 80250 3 80250 3 80250
7 Filler piece 7 80700 7 80700 9 80700 9 80700 11 80700
8 Circular button 49 80155 49 80151 63 80155 63 80151 88 80156
9 Retaining assembly 7 80650 7 80650 9 80650 9 80650 11 80650
DRAWINGS
1.2 Slip segment, left end 1 86113 1 86113 1 86113 1 86113 1 86113
2 Hinge pin 11 80340 12 80340 13 80340 16 80340 16 80340
3 Cotter pin 11 80340-1 12 80340-1 13 80340-1 16 80340-1 16 80340-1
4 Handle right/left end segment 2 80220 2 80220 2 80220 2 80220 2 80220
5 Handle intermediate segment 1 80230 1 80230 2 80230 3 80230 3 80230
6 Handle pin assembly 3 80250 3 80250 4 80250 4 80250 4 80250
7 Filler piece 12 80700 13 80700 14 80700 17 80700 17 80700
8 Circular button 96 80156 104 80154 112 80156 136 80152 136 80156
9 Retaining assembly 12 80650 13 80650 14 80650 17 80650 17 80650
35
CSL / CSC Casing Slips Parts
36
CSL / CSC Casing Slips Parts
CSL pn 87111 CSL pn 87120 CSL pn 87130 CSL pn 87140 CSL pn 87150 CSL pn 87160
Qty Description Qty Partno. Qty Partno. Qty Partno. Qty Partno. Qty Partno. Qty Partno.
1 Slip Segment 9 87114 9 87114 9 87114 10 87114 10 87114 11 87114
intermediate
2 Slip Segment 1 87112 1 87112 1 87112 1 87112 2 87112 2 87112
intermediate
3 Slip Segment left 1 87113 1 87113 1 87113 1 87113 1 87113 1 87113
end
4 Slip Segment right 1 87111 1 87111 1 87111 1 87111 1 87111 1 87111
end
5 Hinge pin 11 80340 11 80340 11 80340 12 80340 13 80340 14 80340
6 Cotter pin 11 80340-1 11 80340-1 11 80340-1 12 80340-1 13 80340-1 14 80340-1
7 Handle right / left 2 80220 2 80220 2 80220 2 80220 2 80220 2 80220
end segment
8 Handle intermediate 1 80230 1 80230 1 80230 1 80230 2 80230 2 80230
segment
9 Retaining screw 3 80250 3 80250 3 80250 3 80250 4 80250 4 80250
with lock washer
10 Filler piece 12 80700 12 80700 12 80700 13 80700 14 80700 15 80700
11 Circulair button 144 80155 144 80150 144 80156 156 80156 168 80156 180 80156
12 Retaining assembly 12 80650 12 80650 12 80650 13 80650 14 80650 15 80650
CSL pn 87165 CSL pn 87170 CSL pn 87175 CSL pn 87180 CSL pn 87195 CSL pn 87196
Qty Description Qty Partno. Qty Partno. Qty Partno. Qty Partno. Qty Partno. Qty Partno.
1 Slip Segment 13 87114 13 87114 13 87114 14 87114 16 87114 18 87114
intermediate
2 Slip Segment 2 87112 2 87112 2 87112 2 87112 2 87112 2 87112
intermediate
3 Slip Segment left 1 87113 1 87113 1 87113 1 87113 1 87113 1 87113
end
DRAWINGS
4 Slip Segment right 1 87111 1 87111 1 87111 1 87111 1 87111 1 87111
end
5 Hinge pin 16 80340 16 80340 16 80340 17 80340 19 80340 21 80340
6 Cotter pin 16 80340-1 16 80340-1 16 80340-1 17 80340-1 19 80340-1 21 80340-1
7 Handle right / left 2 80220 2 80220 2 80220 2 80220 2 80220 2 80220
end segment
8 Handle intermediate 2 80230 2 80230 2 80230 2 80230 2 80230 2 80230
segment
9 Retaining screw 4 80250 4 80250 4 80250 4 80250 4 80250 4 80250
with lock washer
10 Filler piece 17 80700 17 80700 17 80700 18 80700 20 80700 22 80700
11 Circulair button 204 80158 204 80154 204 80156 216 80156 240 80158 264 80158
12 Retaining assembly 17 80650 17 80650 17 80650 18 80650 20 80650 22 80650
CSL pn 87190 CSL pn 87205 CSL pn 87200 CSL pn 87210 CSL pn 87215 CSL pn 87220
Qty Description Qty Partno. Qty Partno. Qty Partno. Qty Partno. Qty Partno. Qty Partno.
1 Slip Segment 17 87114 20 87114 21 87114 22 87114 26 87114 26 87114
intermediate
2 Slip Segment 2 87112 2 87112 2 87112 2 87112 2 87112 2 87112
intermediate
3 Slip Segment left 1 87113 1 87113 1 87113 1 87113 1 87113 1 87113
end
4 Slip Segment right 1 87111 1 87111 1 87111 1 87111 1 87111 1 87111
end
5 Hinge pin 20 80340 23 80340 24 80340 25 80340 29 80340 29 80340
6 Cotter pin 20 80340-1 23 80340-1 24 80340-1 25 80340-1 29 80340-1 29 80340-1
7 Handle right / left 2 80220 2 80220 2 80220 2 80220 2 80220 2 80220
end segment
8 Handle intermediate 2 80230 2 80230 2 80230 2 80230 2 80230 2 80230
segment
9 Retaining screw 4 80250 4 80250 4 80250 4 80250 4 80250 4 80250
with lock washer
10 Filler piece 21 80700 24 80700 25 80700 26 80700 30 80700 30 80700
11 Circulair button 252 80157 288 80158 300 80153 312 80157 360 80158 360 80157
12 Retaining assembly 21 80650 24 80650 25 80650 26 80650 30 80650 30 80650
37
CSL / CSC Casing Slips Parts
CSL pn 87230 CSL pn 87235 CSL pn 87240 CSL pn 87280
Qty Description Qty Partno. Qty Partno. Qty Partno. Qty Partno.
1 Slip Segment 29 87114 32 87114 33 87114 46 87114
intermediate
2 Slip Segment 2 87112 2 87112 2 87112 3 87112
intermediate
3 Slip Segment left 1 87113 1 87113 1 87113 1 87113
end
4 Slip Segment right 1 87111 1 87111 1 87111 1 87111
end
5 Hinge pin 32 80340 35 80340 36 80340 50 80340
6 Cotter pin 32 80340-1 35 80340-1 36 80340-1 50 80340-1
7 Handle right / left 2 80220 2 80220 2 80220 2 80220
end segment
8 Handle intermediate 2 80230 2 80230 2 80230 3 80230
segment
9 Retaining screw 4 80250 4 80250 4 80250 5 80250
with lock washer
10 Filler piece 33 80700 26 80700 37 80700 50 80700
11 Circulair button 396 80157 432 80158 444 80157 612 80157
12 Retaining assembly 33 80650 36 80650 37 80650 51 80650
CSC pn 88110 CSC pn 88120 CSC pn 88125 CSC pn 88130 CSC pn 88160
Qty Description Qty Partno. Qty Partno. Qty Partno. Qty Partno. Qty Partno.
1 Slip Segment 9 87114 10 87114 11 87114 12 87114 14 87114
intermediate short
2 Slip Segment 2 87112 2 87112 2 87112 2 87112 3 87112
intermediate long
3 Slip Segment left 1 87113 1 87113 1 87113 1 87113 1 87113
end
4 Slip Segment right 1 87111 1 87111 1 87111 1 87111 1 87111
end
DRAWINGS
38