Documente Academic
Documente Profesional
Documente Cultură
Figure indicate
a) X-OR
b) *X-NOR
c) CMOS-OR
d) X-NAND gate
A wire is connected to constant voltage supply while its length and radius is doubled
a) electric field is half
*b) electric field is double
c) heat is unchanged
d) electric field remain same
When a new Ni-cad battery is installed, its cell seal is opened and pour electrolyte to ensure the full charge
battery
a) no charge is required
b) charge is given & boost up &(A)
c) as in (b) and suddenly installed in a/c service
*d) as in (b) and after two hours, check the electrolyte and installed in service
When journey from magnetic equator towards pole, the dip and
*a) increased
b) decreased
c) depend upon direction
d) none
Dos is
a) programme
b) processing unit
*c) disk operating system
d) all
Software is a
*a) programme
b) language
c) operating system
d) all
The work done on a moving charge from one point to another is depend upon
a) the path taken
*b) position of two points
Algorithm
*a) Consists of finite no. of steps has outputs are definite
b) Consists of infinite no. of steps
c) May not have out put
d) None
Unix is
*a) single operating unit b)double operating unit (multi purpose)
c) CAD & record of engineering organization
a) software used
b) frequency and signal received
*c) both software and hardware used
d) only on hardware used
Representation of GATES is
a) = c) =
b) = d) =
If 28 volt current is passed through resistant of 10Ω, the power consumed by that component is
(P=V=V²/R)
*a) 78.4 watt b) 780 w c)784 w d) 0.78w
A transducer converts
a) electrical energy into mechanical energy
b) mechanical energy into electrical energy
c) chemical energy into electrical energy
*d) one form of energy into another (electrical) energy
Analogue computer is
a) more correct than digital computer *b) less accurate than digital computer
c) equal to digital computer d) none
The magnitude of induced emf produced in a coil, when a magnet is inserted in it, does not depend upon
a) no. of turns in coil
*b) resistance of coil
c) magnetic moment of magnet (magnetic strength)
d) speed of rotation of magnet
A transfer is___
*a) amplify the low input signal to high output signal
b) used as a rectifier
c) used in transducer set
d) both a & c are correct
When a lead-acid battery is charged by constant current method, then its full charge can be detected as
a) Three testing of electricity gives same specific gravity value
b) Voltage stops rising
c) Gassing will occurs rapidly
d) All above are wrong
A cathode (electron emitter) used in thermionic emission must have following characteristics
a) high mech. point
b) high mech. strength
c) low work function
*d) all above are correct
Which of the following frequency is used for space propagation
a) 2 KHZ
*b) 30 MHZ and above
c) up to 30 MHZ
d) 20 KHZ – 200 MHZ
In an inductive circuit
*a) current lags behind voltage by 90° b) current leads behind voltage by 90°
c) current and voltage are in phase d) None
An ac circuit consists of inductance of 10Ω, capacitance 4Ω & resistance 8Ω the impedance of the circuit
is Z=√R²+(XL-XC)
a) 6Ω *b) 10Ω c) 5.5Ω d) 8Ω
The static vents with the flat surface plate at two position to
a) minimize position error
b) have is formation freedom
*c) both a & b
d) none
An ac circuit has inductance 3Ω and resistance of 4Ω, then impedance of the circuit is
a) 3Ω b) 1Ω *c) 5Ω d) 7Ω
A B Y
0 0 0
0 1 1
1 0 1
1 1 0
A) OR-gate
*B) X – OR gate
C) AND-gate
D) NAND gate
The modulation in which, amplitude is kept constant and frequency is changed is called
a) amplitude modulation
b) space modulation
*c) frequency modulation
d) phase modulation
In uniform fluid flow, the fluid is first made to flow through a tube and the pressure exerted by the fluid is
measured by
*a) dynamic pressure
b) static pressure
c) Reynolds’s no.
d) all
(0.625)10=( )2
a) 0.110 *b) 0.101 c) 0.011 d) 0.100
(1010101)2 = ( )10
a) 110 *b) 85 c) 75 d) 95
Power factor in d.c. circuit is
*a) unity
b) infinite
c) zero
d) none
For given figure, which is correct a) 0,0,1 *b) 1,0,1 c) 1,1,0 d) 1,0,0
B
C
1
When three individual resistance are connected in parallel to each other which of the following is correct
a) R = R1+R2+R3 *b) 1/R = 1/R1 + 1/R2 + 1/R3
In a transformer is primary frequency changes from 50Hz to 60Hz, keep the peak voltage constant then
frequency
*a) increases in secondary by ratio 60/50 b) decreases in secondary by ratio 50/60
b) both 1 & 2
c) none
When coil of wire is placed horizontal to the earth surface, and a bar magnet dropped from the top
a) fall with acceleration equal to ‘g’ *b) fall with acceleration less than ‘g’
(1010101)² =_________
*a) (85)10 b) (58)10 c) (64)10 d) none
If acid is spilled over skin from an Ld-Acid a/c battery then it cleaned with
a) water
b) water & boric acid
*c) water & bicarbonate of soda
d) all
For a battery to have high ampere hour capacity and high terminals voltage
*a) low internal resistance
b) high internal resistance
c) does not depend on internal resistance d) none
1 HP is usual to
a) 735 electric watts *b) 746 electrical watts c) both a & b d) none
When two sphere of same mass, one is +ve charged and other is –ve charged, then new mass will
a) change
*b) unchanged
If the conductor is of 4Ω and it stretched to twice of its length, then its resistance is
a) 1Ω b) 8Ω c) 12Ω d) 16Ω
A & B are big and small battery, having same emf. Internal resistance of battery A is
*a) less than B
b) greater than B
c) equal to B
d) unaffected
Transistor is biased
*a) base and emitter forward biased
b) base and emitter reverse biased
In pitot static system, static vents are placed separately in a/c to reduced
a) vacuum gauge
b) vacuum chamber
*c) micro manometer
d) all
An altimeter has
a) stack of three evacuated bellows
b) stack of two evacuated bellows
c) barometric pressure setting provision *d) all
Transistor used as
a) voltage regulator/double
b) rectifier
*c) amplifier
d) all are correct
In a capacitor
a) capacity depends on separation of plates and measured in farad
b) capacity depends on area of plates and measured in farad
c) capacity depends on nature of dielectric material *d) all
Zener diode
a) has high forward voltage rating *b) has negative resistance
c) has a sharp breakdown of low reverse voltage d) used as amplifier
a) automatic react
b) momentary react type
c) *momentary switch type
d) none
a b
V=0
a) 1/3 from a to b
b) 2/3 from a to b
c) 1/3 from b to a
d) *zero
a) *OR-gate
b) AND-gate
c) NOT-gate
d) XOR-gate
a) *capacitor
b) condenser
c) resistor
d) none
In an alto meter if there is absence of barometer is pressure, the pitot line is checked by:
a) vacuum chamber
*b) micrometer
In pitot static system the static vent to of the flat plate tube any where in the a/c structure to prevent.
a) position error
b) instrument error
c) protection against ice formation
*d) both a & c are correct
A triode consists of
a) a plate grid and a heater
b) a plate, cathode and a heater
c) plate, screen and a heater
d) plate, cathode, heater and wire screen between the plate and cathode
Taking all the factors into consideration the most commonly used metal as electrical conducting
a) aluminum a) copper b) silver c) iron
In ATA coding system the size & type of the elc cables/wires in a/c are given by:
a) prefix and suffix
b) side by side
c) numbers and letters
d) none of the above
A transistor is
a) amply the low input signal to high output signal
b) used as a rectifier
c) used in transducer set
d) a & b are correct
For getting high ampere hour capacity and high terminal voltage the plate of cells should be connected as
a) in series so that to get high internal resistance
b) in series so that to get low internal resistance
c) in parallel so that to get low internal resistance
d) in parallel so that to get high internal resistance
For any battery the charged with continent current conditions can be found while changing
a) specific gravity taken at interval of 30 min three consecutive redings should be same
b) gassing will occur
c) voltage stops rising
d) a & b are correct
A 35 AH, 12 V battery is discharged according to the following rates which will give max. capacity?
a) 10 hrs, discharge rate
b) 15 hrs, discharge rate
c) 20 hrs discharge rate
d) 5 hrs discharge rate
The motor with two different coils wound on difference sence, which can rotate in two direction is
a) series
b) shunt
c) compound
d) differentially compound motor
If the generator output were fluctuating, how would you place a resistor in the line to settle out the
fluctuations
In series with the generator
The type of control switch used for a retractable landing light is described as
A single pole double throw (SPDT)
The voltage regulator has a broken wire in the coil under this circumstances you will obtain
Zero voltage
During the operation of a four engine aircraft, which of the following generator controls are available to
the pilot
Each of the four generators has a switch that is in series with each generator field
During flight, all the gear, down lock indicator lights burn-out. How would this affect the gear warning
horn system
It would have no effect
You are about to install some parachute flares. Before actual installation, you should
Turn both the master switches and flare switch to the off-position
During flight, when more electrical power is needed, the generator voltage will
Remain at a constant voltage, however, the current flow will increase
The tensile strength of the cable to terminal joints should be at least equivalent to
The tensile strength of the cable itself
When frequent disconnections are required in the electrical system, the mechanic should use in order to
facilitate maintenance
Connectors (plugs and receptacles)
Electric wiring that offers the advantages of case of installation, simple maintenance and reduce weight is
known as
Open wiring method
Junction boxes should be mounted with the open side facing downward, this arrangement permits
Loose metallic objects, such as washers, bolts etc to fall out of the box and prevent possible short
circuits
An arcing fault between an electric cable and a metallic flammable, fluid line may puncture, the line and
result in a serious fire, when separation is impracticable, the electrical cable should
Be places over flammable fluid line and securely clamped to the structure
When poles pieces are made to project inward from the frame, they are called
a. interpoles b. riserpoles
c. silent poles *d. salient poles
A variable shunt is connected across ‘Series field’ to get varied degree of compounding. This shunt is
called
*a. Diverter b. Inter-shunt
c. multiplier d. none
The positive armature lead connects to terminal (in 24V gen. system)
*a. B terminals b. C terminals
c. A terminals d. any
Which unit drops ‘Alternator form circuit when an overvoltage condition exists
*a. ACU b. APU
c. ADU d. ACC
If the specific gravity read by the hydrometer is 1.240 & electrolyte temperature is 60 degree F then,
e) corrected specific gravity will be higher than the indicated specific gravity.
f) *Corrected specific gravity will be lower than the indicated specific gravity.
g) 60 degree F is standard temperature, therefore, correction in indicated reading is
h) not required.
i) Specific gravity of electrolyte is not depends on temperature.
When a specific voltage is placed across the diode in its reverse bias direction, it will break down &
conduct :
*a) Zener diode b) PN diode c) Vacuum diode d) DIAC
positive symbol of :-
a. A C Generator
b. *DC Generator
c. DC Motor
d. Inverter
The colour code resistor having the color of red green yellow and no color at the last the resistance value
will be :-
a. 300, 000
b. 200, 000
c. *250, 000
d. a & b are correct
710. Which of the following material has a negative temperature coefficient of resistance ?
a. Brass
b. Copper
c. Aluminium
d. *Carbon
715. Separately excited generators are not suitable for normal use because
a. separate D.C. source is required
b. loss of armature reaction can not be compensated
c. the output voltage will vary as per the variation of load
*d. all are correct
719. When the motor armature and field are getting same amount of current, the motor is said to be
a. shunt motor
*b. series motor
c. compound wound motor
d. none of these
724. In brush less generator, the output from exciter field is rectified by
a. six diode fitted on stator assembly
b. five diode fitted on rotor
*c. six silicon diode fitted on rotor
d. none of the above
a. Moving
b. Stationary
*c. Near its full deflection
d. Just starting to move
727. Permanent magnet moving coil ammeter have uniform scales because :-
a. Of eddy current damping
b. They are spring controlled
*c. Their deflection torque varies directly as current
d. Both b and c
728. The meter that is suitable for only direct current measurement is :-
a. Moving Iron type
*b. Permanent magnet type
c. Electrodynamic type
d. Hot wire type
729. The hair spring used in the pointer of moving coil type instrument is generally made of
a. Phosphor bronze
b. Non magnetic
c. Wood
*d. Both a & b are correct
733. Voltage induced in the three windings of a 3-phase alternator are ______ degree apart in time
phase :-
*a. 1200
b. 600
c. 900
d. 300.
735. The direction of induced emf can be found with the help of :-
*a. Lenz’s law b. Faradays law
c. Kirchoff’s law d. Laplace law
736. Which of the following instruments is equally accurate on d.c. as well as a.c. circuit :-
739. The factor determines whether a transformer is a step up or step down depends on
*a. no. of turns b. core strength
c. lamination d. size of transformer
748. The direction of induced e.m.f can be found with the help of
a. lenz’s law
*b. Fleming’s right hand law
c. Ohm’s law
d Kirchoff law
753. Ni/Cad cell is advantageous over Pb-acid cell from ___________view point
a low maintenance cost and long service life
b. short recharge time and good reliability
c. excellent reliability and good starting ability
*d. all of the above
754. Which method is used to charge the battery in a/c and why?
*a. constant voltage method because a/c electrical system voltage remain constant
b. constant current method order to reduce the charging time
c. constant current method to avoid much supervision
d. constant current method to need relatively less time
759. If electrolyte from a lead acid battery is spilled in the battery compartment, which procedure
should be followed?
a. apply boric acid solution to the affected area followed by a water rinse
b. rinse the affected area thoroughly with clean water
*c. apply sodium bicarbonate soul to the affected area followed by a
water rinse
d none of these
760. The method used to rapidly charge a nickel cadmium battery utilizes
a. constant current and constant voltage
b. constant current and varying voltage
*c. constant voltage and varying current
d. none of these
761. The ‘servicing’ and ‘charging of nickel-cadmium and lead acid batteries together in the same
service area is likely to result in
a. normal battery service life
b. increased explosion and or fire hazard
*c. contamination of both types of batteries
d. none of these
762. In a constant current charging system, a battery requires attention at the end of charge to avoid
a. sulphation of battery b. spilling of electrolyte
c. Evaporation of electrolyte *d. Danger of overheating
779. Ideal constant voltage source has _______ internal resistance while practical constant current has
_________ internal resistance :-
a. Zero infinity
b. *Zero, very high
c. Very low, very high
d. Very low infinity
782. Two wire A & B have the same cross section and are made of same material. Resistance of ‘A’ is
600 Ohms and resistance of ‘B’ is 100 Ohms, the number of times ‘A’ is longer than ‘B’ is :-
a) 2
b) 5
*c) 6
d) 2
784. The ratio of resistances of a 100 watt, 220volt lamp to that of 100 watt, 110V lamp will be , at the
respective voltage :-
a) 2:1 b) 1:2 c) 1:4 *d) 4:1
792. The algebraic sum of current at any junction of conductors in a circuit is zero. It is known as
a) Ohms law
*b) Kirchhoff law
c) Lenz law
d) Faradays law of induction
793. The nominal current relating to an aircraft switch is normally stamped on the :-
a) Switch housing
*b) Face plate
c) side of the switch
d) Non-metallic housing
798. The greatest value attained during one half cycle is called :
*a) Peak value
b) Average value
c) RMS value
d) Effective value
803. Which of the following statement is true for both series and parallel DC circuit :-
*a) Power are additive
b) Voltage are additive
c) Current are additive
d) Element have individual current
808. The range of voltmeter and ammeter can be extended by using _______ and respectively :-
a) shunt, Multiplier
*b) Multiplier, Shunt
c) Ammeter is connected in parallel
d) Multiplier, Multiplier
810. Permanent magnet moving coil ammeter have uniform scale because :-
a) of eddy current damping
b) they are spring controlled
*c) their deflecting torque varies directly as current
d) both b) & c) are correct
811. The meter that is suitable for only direct current measurement is :-
a) moving iron type
*b) permanent magnet type
c) electrodynamic type
d) hot wire type
813. In twin engine light A/c which items are common to both engine for starting :-
a) Ignition solenoid and battery
b) Ignition solenoid and battery solenoid
*c) Battery solenoid and battery
d) Battery solenoid, igniters solenoid
814. In turbo prop engine starting system – blow out facility is provided to :-
a) Purge the fuel vapour after a successful start
*b) Purge the fuel vapour after an un-successful start
c) Assist in starting
817. A fully charged A/c battery (lead acid type) electrolyte contains
a) 40% water and 60% acid
b) 30% acid and 70% water
c) 60% water and 90% acid
*d) 30% acid & 70% water, both by volume
818. During installation of battery in A/C, _________ terminal is connected first in order to ______ :-
a) Positive, complete the circuit
b) Negative, complete the circuit
*c) Positive, avoid the accidental short
d) Negative, to avoid accidental short
820. In a circuit, the voltage is doubled and the resistance is cut in half at the same time, the current
will be :-
a) Doubled
b) A quarter
c) A half
*d) Four time as high
827. When a conductor moves parallel to the magnetic flux with very high speed, the induced voltage
is :-
a) Maximum depending on different factors
*b) Zero, because rate of cutting of flux is negligible
c) Some value
d) Zero because cutting flux is maximum
830. When a conductor moves parallel to the magnetic flux with very high speed, the induced voltage
is :-
a) Maximum depending on different factor
b) Zero because cutting flux is maximum
*c) Zero, because rate of cutting of flux is negligible
d) Some value
834. Shunt generator are most suited for stable parallel operation because of their voltage ________
characteristics :-
a) Identical
*b) Drooping
c) Linear
d) Rising
836. The method most often used in overcoming the effect of armature reaction is through the use of :-
*a) Inter poles
b) Alnico field pieces
c) Speed poles
837. Between no load and full load the motor which develops the least torque is :-
a) Series motor
*b) Shunt motor
c) Cumulative compound wound motor
d) Differentially compound wound motor
845. Separately excited generator are not suitable for normal use because
a. separate D.C. source is required
b. loss of armature reaction can not be compensated
c. the output voltage will vary as per the variation of load
*d. all are correct
850. While synchronizing, circuit breaker should be closed when synchronizing lamp
a. blink rapidly
b. blink slowly
c. blink 10 times per second
*d. blinking decreases to one blink or less per second
854. The phase sequence protection unit in AC external power supply system provide power supply to
*a. control relay
b. external power breaker relay
c. to limiting resistor
d. both a & b
858. Which of the following instruments develop error due to position error
(a) Altimeter & VSI (b) ASI & VSI
*(c) ASI & Altimeter (d) Altimeter & Machmeter