Documente Academic
Documente Profesional
Documente Cultură
Equipment Catalog
Petromac
Tool Taxi Type A TTA-35805 & TTA-35815
Description Application
TTA-35805 and TTA-35815 are slip-over tool • Gravity logging up to 70 degrees well
taxis, with tungsten carbide bush bearings, deviation using a slip-over wheel design
designed to orient & reduce the drag coefficient • Orient logging tool sensors, cores,
of a logging tool string. pressure measurements and samples
without the need for standoffs, bow
Taxis lock securely onto the tool housings or into springs, tool turners etc.
c-spanner recess holes and fit both 3 5/8” and 3 • Stick-slip and cable tension reduction
3/8” logging tool housings. • Eliminate risk of tool differential sticking
There are two different models of Tool Taxi by offsetting tools from the wellbore
which provide either 0.5” or 1.5” standoff in an wall.
8.5” wellbore. • Robust design. Very low maintenance
requirement.
2
Petromac
Technical Specifications
1. Fits a 3 5/8” logging tool and a 3 3/8” tool housing (via a sleeve). Other versions, TTA-705 and TTA-715 are also available
with a 3.7” bore.
2. Set standoff parameters to appropriate offset. See Appendix-A
3. Tungsten Carbide must not be subjected to shock loadings. Do not hit with a hammer or use gas torch.
3
Petromac
Description Application
TTB-505 and TTB-515 are slip-over tool taxis, • Gravity logging up to 80 degrees well
designed to orient & reduce the drag coefficient deviation using a slip-over wheel design
of a logging tool string. • Orient logging tool sensors, cores, and
pressure measurements and samples
Taxi wheels run on ball bearings in a sealed, without the need for standoffs, bow
pressure compensated, lubricant bath providing springs, tool turners etc.
the lowest friction in class. • Stick-slip and cable tension reduction
Taxis lock securely onto the housings or into c- • Eliminate risk of tool differential sticking
spanner recess holes and fit both 3 5/8” and 3 by offsetting tools from the borehole
3/8” logging tool housings. • Robust design. Very low maintenance
requirement.
There are two different models of Tool Taxi
which provide either 0.5” or 1.5” standoff in an
8.5” wellbore.
4
Petromac
Technical Specifications
1. Fits a 3 5/8” logging tool and a 3 3/8” tool housing (via a sleeve)
2. Set standoff parameters to appropriate offset. See Appendix-A
5
Petromac
In-line Tool Taxi TTC - IL6
Description Application
TTC-IL6 are in-line tool taxis designed to orient & • Gravity logging up to 70 degrees well
reduce the drag coefficient of a logging tool string. deviation
• Orient logging tool sensors, cores,
Taxis make up in-line, directly to wireline logging pressure measurements and samples
tools, without the need for adapters. without the need for standoffs, bow
The Taxis are designed for use in small wellbores springs, tool turners etc.
(6.0” +) • Stick-slip and cable tension reduction
• Eliminate risk of tool differential sticking
These taxis use durable, tungsten carbide bush
by offsetting tools from the borehole
bearings.
• Robust design. Very low maintenance
requirement.
6
Petromac
Technical Specifications
TTC-IL6
Weight, lbs 32.8
Length, in 17.75
Volume, ft3 0.11
Min. Hole size, in 6.0
Max. Hole size, in 8.0
Drag coefficient, dynamic 4%
Drag coefficient, static 8%
Temperature rating, oF 350
Pressure rating, psi 30,000
Taxi OD, in 5.25”
Wheel Diameter 4.0”
Connection 1 In-line with all through wired tools
Standoff in 6” wellbore2,3 0.44”
Materials 17-4 PH SS, Heat treated H1150
Bearings Tungsten Carbide Composite
Diaphragm Up to 230degF use White Nitrile, Elongation 400%
Up to 480degF use Black Viton, Elongation 250%
Fastenings 304 SS. UNC thread. Hex key 3/16”
Grease - lubrication unit Lubriplate 930AA
SWL for Fishing, lbs. 30,000
7
Petromac
Formation Testing TTB-S75 & TTB-S85
Description Application
Tool Taxi specifically designed for Pressure and • Proven gravity logging up to 80 degrees
Sampling tools. well deviation using a slip-over wheel
TTB-S 75 / 85 are slip-over tool taxis that lock design
securely onto 4.75”-5.25” tool housings and • Orient probe in the desired direction for
allow the heavy formation testing tool string to optimal pressure measurements and
be fully carried on wheels. samples
• Stick-slip and cable tension reduction
Taxi wheels run on ball bearings in a sealed, • Eliminate risk of tool differential sticking
pressure compensated, lubricant bath providing the by offsetting tools from the borehole
lowest friction in class. without the need for additional tool
body standoffs
• Robust design with a very low
maintenance requirement
8
Petromac
Technical Specifications
TTB-S 75 TTB-S 85
Weight, lbs. 22 32
Materials
Fastenings 304 Stainless steel. UNC threads. Hex keys ¼”, 3/16”
1. Custom TTB-S75 with 5” bore is also available for high pressure tools
2. Custom TTB-S85 with 5.25” bore is also available for high pressure tools. Sleeve available for S85 use on 4.75” tools.
3. Up to 12,700lb dependant on tool modules used
9
Petromac
Centralizing Tool Taxi TTB-X-515
Description Application
TTB-X 515 Taxis are used to centralize tool • Tool centralization without the need
strings in an 8.5” wellbore. inefficient drag-inducing centralizers
• Gravity logging up to 80 degrees well
Taxis lock securely onto the housings or into deviation
c-spanner recess holes. Taxi wheels run on • Stick-slip and cable tension reduction
ball bearings in a sealed, pressure • Eliminate risk of tool differential sticking by
compensated, lubricant bath providing the offsetting tools from the borehole without
lowest friction in class. the need for additional tool body standoffs
10
Petromac
Technical Specifications
Model TTB-X-515
Weight, lbs. 28
Length, in 11.6
Volume, ft3 0.06
Min. Hole size1, in 8.5”
Max. Hole size, in 8.5”
Drag coefficient, dynamic 2%
Temperature rating, oF 350
Pressure rating, psi 30,000
Taxi OD, in 7.7”
Wheel Diameter 6”
Taxi Bore2, in 3 5/8”
Materials
Castings 17-4 PH SS, Heat treated H900
Ball bearings Custom, double row, angular contact
Up to 230degF use White Nitrile, Elongation 400%
Diaphragm
Up to 480degF use Black Viton, Elongation 250%
Fastenings 304 Stainless steel. UNC threads. Hex keys ¼”, 3/16”
Attachment Alloy steel grub screw, ¼ ” hex, UNC thread, dog end type
Grease - lubrication unit Lubriplate 930AA
SWL for Fishing, lbs. 50,000
SWL Shear Set Screws, lbs. 8,500
11
Petromac
Guide - Adjustable AHF-C
Description Application
Petromac hole finders, used in conjunction with • Ability to navigate step ledges of up to 5”
Tool Taxis, are designed to slide over • Adjustable angle to suit multiple hole
obstructions in a well bore. sizes/situations
The AHF-C guide has an adjustable nose angle. • Helps tool run over cuttings and other
It is set to suit the hole size and logging tool low side obstructions
standoff. • Attached to the bottom without any
electrical interference
The Guide is suitable for attachment to the • Robust design with negligible
bottom of any through-wired tool. maintenance requirements
12
Petromac
Technical Specifications
AHF-C
Length, in 35”
Weight, lbs. 36
Materials
Nose Aluminum
13
Petromac
Induction Guide HF6-AIT,
HF6-ZAIT
Description Application
Petromac hole finders, used in conjunction • Ability to navigate step ledges of up to 4.5”
with tool taxis, are designed to slide over • Suitable for hole sizes 8.5” and larger
obstructions in a well bore. • Helps tool run over cuttings and other low
Induction Guides, such as HF6-AIT and HF6- side obstructions.
ZAIT, are specifically designed to be run at the • Suitable for Array Induction tools with no
bottom of induction logging tools, electrical interference.
• Guides for use in water base muds are
The Guides have a fixed nose angle of 6deg. available which allow the measurement of
The Induction Guide nose is manufactured SP and Rm data.
from carbon fiber composite. • Guides for smaller holes can be custom
Robust design with minimal maintenance manufactured.
requirements
14
Petromac
Technical Specifications
HF6-AIT HF6-ZAIT
Length, in 26” 26”
Weight, lbs. 9 9
Volume, ft3 0.04 0.04
OD, in 4” (at no-go collar) 4” (at no-go collar)
Angle 6 degrees fixed 6 degrees fixed
Maximum step ledge1 Up to 4 ½” in 8.5” wellbore Up to 4 ½” in 8.5” wellbore
Min. Hole size, in 7” 7”
Max. Hole size, in No Limit No Limit
Temperature rating, oF 350 350
Pressure rating, psi 30,000 30,000
Materials
Body 17-4 PH SS 17-4 PH SS
Nose Carbon Fiber Carbon Fiber
SWL for fishing, Tensile 5,000 lbf 5,000 lbf
Compressive strength 6,000 lbf 6,000 lbf
15
Petromac
Induction Guide HF-12 QAIT
Description Application
16
Petromac
Technical Specifications
HF-12 QAIT
Length, in 13”
Weight, lbs. 6
OD, in 2.8”
Materials
Nose Aluminum
17
Petromac
FMI Hole finder HF5-FMI
Description Application
Petromac hole finders, used in conjunction • The hole finder will navigate the FMI over
with tool taxis, are designed to slide over step ledges 4” high.
obstructions in a well bore. • Helps tool run over cuttings and other low
FMI hole finders are specifically designed to side obstructions.
attach to the bottom of the Formation Micro- • Robust design with no electrical interference
Imager. and negligible maintenance requirements.
The FMI hole finder is ultra-lightweight and • The Petromac system prevents image
virtually buoyant in drilling mud. It does not rotation.
interfere with Pad contact and data quality • Guides for smaller holes can be custom
is ensured. manufactured.
• No electrical interference and negligible
The Guides have a fixed nose angle of 5deg.
maintenance requirements
18
Petromac
Technical Specifications
HF5-FMI
Length, in 24”
OD, in 4.5”
Materials
19
Petromac
Formation Testing Hole finder HF6-MDT
Description Application
Petromac hole finders, used in conjunction • Ability to navigate step ledges up to 4.5”.
with tool taxis, are designed to slide over • Helps tool run over cuttings and other low
obstructions in a well bore. side obstructions.
Hole finders are specifically designed to be • Robust design with no electrical interference
run at the bottom of formation testing and negligible maintenance requirements.
strings with a fixed angle that does not • Fixed angle that does not obstruct probe
interfere with probe setting. contact with borehole.
20
Petromac
Technical Specifications
HF6-MDT
Length, in 24”
OD, in 4.5”
Materials
Nose Aluminum
21
Petromac
MSCT Hole finder HF8-MSCT
Description Application
Petromac hole finders, used in conjunction • Ability to navigate step ledges of up to
with tool taxis, are designed to slide over 4.5”
obstructions in a well bore. • Orient the coring tool to obtain cores in
MSCT hole finders are specifically designed to the direction of stress plane and for
be run at the bottom of sidewall coring tools, optimal core recovery
such as XL-Rock and MSCT. • Helps tool run over cuttings and other low
side obstructions.
22
Petromac
Technical Specifications
HF8-MSCT
Length, in 24”
OD, in 4.5”
Materials
Nose Aluminum
23
Petromac
J-Latch Hole finder HFJ9
Description Application
Petromac hole finders, used in conjunction • Ability to navigate step ledges of up to 4”
with tool taxis, are designed to slide over • Integrated slots for 3x thermometers
obstructions in a well bore. • Helps tool run over cuttings and other low
The HFJ9 hole finder is specifically designed to side obstructions
be run at the bottom of tools with a J-Latch • Robust design with no electrical
connection such as ACRt or MCI. interference and negligible maintenance
requirements
With integral slots for thermometers, the HFJ9
replaces the traditional temperature sub.
24
Petromac
Technical Specifications
HFJ9
Length, in 17.2”
Weight, lbs. 16
OD, in 3.625”
Materials
Nose Aluminum
25
Petromac
Description Application
The Petromac hole finder & orientation • Ability to navigate step ledges of up to 5”
assembly attaches to the bottom of tool strings • Helps tool run over cuttings and other low
via a standard flex joint (DITS connection). side obstructions
The assembly is comprised of quick-connect • Robust design with negligible
3pcs for easy transportation and rig-up (5.1m maintenance requirements
total length). • Suitable for use where standard
orientation technology cannot be used
Swivel may be locked to orient the complete
tool string.
26
Petromac
Technical Specifications
SWHF
Length, in 169”
OD, in 3.625”
Materials
Nose Aluminum
27
Petromac
Appendices
28
Petromac
Appendix - A
Taxi/Guide configurations in various hole sizes
29
Petromac
Standoff configurations
TTA 35805 TTA 35815
TTB 505 TTB 515
Figure 1: 0.5" standoff taxi on a 3 5/8" tool Figure 2: 1.5” standoff taxi on a 3 5/8” tool
30
Petromac
Formation Testing Taxi in various wellbores
31
Petromac
S-75 S-85
Hole size Standoff, in Standoff, in
8.5” 0.8” N/A
12.25” 0.5” 1.0”
14.75” 0.4” 0.9”
32
Petromac
Centralizing Taxi configurations
33
Petromac
AHFC configurations
Tool taxi
34
Petromac
35
Petromac
36
Petromac
37