Sunteți pe pagina 1din 8

4/20/2018 Reinforced Concrete Design: Chapter 7 - Analysis of continuous one-way slabs

More Next Blog» Create Blog Sign In

Reinforced Concrete Design


Detailed description of the steps involved in the design of reinforced concrete members and
structures, according to the Limit state method.

HOME INTRODUCTION CONTENTS READING TIPS INDEX CONTACT US DISCLAIMER PRIVACY POLICY

ad Tu e s d a y, D e c e m b e r 3 1 , 2 0 1 3

7% Chapter 7 - Analysis of continuous one-way slabs

In the previous chapters we saw the analysis and design of simply supported beams and slabs. In
this chapter we will discuss about the analysis of continuous one-way slabs. When we complete this
discussion about continuous one way slabs, we will be able to do the analysis of continuous beams also.

A video of a small scale experiment, showing the behaviour of continuous beams can be seen here
16%
A 3D view of a continuous beam is given in fig.7.1 below. A view of a continuous slab can be seen in
fig.7.2

Fig.7.1
View of a continuous beam

99%

35%

Before we proceed with the discussion on continuous members, we must know how to calculate the
'Effective span' of the various spans. A detailed discussion is given here.

We have already discussed about the effective span of simply supported members here.
advt

To design a member like a slab or beam, we have to first find the bending moments (BM) and shear
forces (SF) at the various points (supports, midpoints of spans etc.,) of the member. In the case of
Ads
simply supported members, these can be found out easily using the three equations of equilibrium. But
in the case of continuous members, we have to use one of the methods like Moment distribution
method, Slope deflection method or kani's method.
ad links
Following solved example demonstrates the method of obtaining the BM and SF at various points of a
SPONSORED LINKS continuous slab.
Slab Foundation
Solved example 7.1:
Consider a continuous one-way slab ABCD shown in the fig.7.2 below. It has a thickness of 200mm. It
Steel Beam
carries a Dead load of 1.5 kN/m2 in addition to it's self weight. Also there is a LL of 4 kN/m2. The
effective spans of AB, BC and CD are 4.5, 4.0 and 4.2 m respectively. Our aim is to find the bending
advt links
moments and shear forces at different points of the slab.

SPONSORED LINKS Fig.7.2


View of continuous slab ABCD
A Design

Concrete Depth

ads links

https://limitstatelessons.blogspot.in/2013/12/chapter-7-analysis-of-continuous-one.html 1/8
4/20/2018 Reinforced Concrete Design: Chapter 7 - Analysis of continuous one-way slabs
SPONSORED LINKS

Steel Structure

Data Analysis

VISITORS

Solution:
Just as we saw in the case of a simply supported one-way slab, in the case of a continuous one-way
slab also, we consider a strip of 1m width. This strip extends from one end support 'A' to the other end
support 'D', as shown in the fig.7.3 below:

Fig.7.3
Strip of 1m width in a continuous slab

Now it has become a continuous beam of width 1m, and total depth D which is equal to the thickness of
the slab. We know how to calculate the load per meter length of this beam: It is the load per meter
area of the slab. (details here) So the next step is to calculate this load per unit area.

DL per unit area:


• Self weight = 25D = 25 x0.2 = 5.0 kN/m2
• Additional DL (given) = 1.5 kN/m2
• Total DL, wDL = 6.5 kN/m2
Thus wu,DL = 1.5 x6.5 = 9.75 kN/m2

• LL per unit area (given) wLL = 4.0 kN/m2


Thus wu,LL = 1.5 x4.0 = 6.0 kN/m2

We have computed DL and LL separately. The reason for this will be explained soon.

These loads per square area on the slab is same as the load per meter length of the 1m wide beam. So
we can write:

• wu,DL per meter length of the beam = 9.75 kN/m


• wu,LL per meter length of the beam = 6.0 kN/m

With the above information, we can draw the line diagram for analysis. This is shown in the fig.7.4
below:

Fig.7.4
Line diagram for analysis

Based on the above fig.7.4, we can do the structural analysis of the beam ABCD. We can use methods
like slope deflection method, moment distribution method, or kani's method. (The steps of the

https://limitstatelessons.blogspot.in/2013/12/chapter-7-analysis-of-continuous-one.html 2/8
4/20/2018 Reinforced Concrete Design: Chapter 7 - Analysis of continuous one-way slabs
structural analysis are not shown here). Based on the results of the analysis, we can draw the BM and
SF diagrams. These are shown in the figs.7.5 and 7.6 below.

Fig.7.5
Bending moment diagram

Fig.7.6
Shear force diagram

We can tabulate the values at different points as shown in the fig.7.7 below:

Fig.7.7
Tabulated results

So from the above table, we will get the required values of BM and SF at the various points. It may
seem that we can now start the design process. But we are not there yet. The values in the above
table, are not the 'maximum values'. Even though the whole beam ABCD has been loaded with all the
maximum LL and DL, there are some 'possibilities' by which, the BM and SF at the various points along
the beam will exceed the values shown in the table. Let us now examine such possibilities:

Consider a situation in which the first span AB is loaded with maximum possible DL and LL. But it's
adjacent span BC and the span CD after that does not carry any LL. The line diagram of this situation is
shown in the fig.7.8 below:

Fig.7.8
LL on span AB only

https://limitstatelessons.blogspot.in/2013/12/chapter-7-analysis-of-continuous-one.html 3/8
4/20/2018 Reinforced Concrete Design: Chapter 7 - Analysis of continuous one-way slabs

Note that in the above fig., the DL on spans BC and CD, are the 'unfactored' DL. This means they are
the characteristic DL. The reason for this can be explained as follows: We want to know the result when
'full load' is applied on AB and 'reduced load' is applied on BC and CD. So we make a reduction on the
loads on BC and CD. While making such a reduction, we must make a 'maximum possible reduction'. To
achieve this, we must remove not only the LL, but also the 'Extra DL that can possibly occur'. So we
avoid the application of the 'Load factor' to the DL, thus using only it's characteristic value. In short, we
are using the 'lowest possible loads' on BC and CD.

Based on the above line diagram, we can do a structural analysis. The results are shown in the table in
fig.7.9 below:

Fig.7.9
Tabulated results

We can see that the sagging moment at the midspan in AB is now 27.13. But in the fig.7.7, it was
24.95. So the sagging moment has increased due to the reduction in loads on other spans. In this way,
the moments at other points also may increase depending on the pattern of loading. We must consider
all possibilities. That is., we must consider all possible load combinations. We must do the structural
analysis for each of these combinations, and then note down the maximum value at various points. All
possible combinations are analysed, and the results are shown in tabular form in the fig.7.10 below:

Fig.7.10
Possible combinations and results

https://limitstatelessons.blogspot.in/2013/12/chapter-7-analysis-of-continuous-one.html 4/8
4/20/2018 Reinforced Concrete Design: Chapter 7 - Analysis of continuous one-way slabs

Now from the above fig., we have to take out the maximum values at each point along the length of the
slab. This is shown in the fig.7.11 below:

Fig.7.11
Extreme values

https://limitstatelessons.blogspot.in/2013/12/chapter-7-analysis-of-continuous-one.html 5/8
4/20/2018 Reinforced Concrete Design: Chapter 7 - Analysis of continuous one-way slabs

In the above figs., '1' denotes the maximum BM at supports; '2' denotes the maximum BM at midspans,
and '3' denotes the maximum SF at supports.

*2.a denotes the minimum BM at midspans. We have to take special care about minimum BM in BC
because, for one particular combination (case 6), this mid span is bending upwards. This usually
happens when a lightly loaded short span comes in between two heavily loaded long spans.

We can examine the various extreme values in the above fig. and make the following conclusion:

(a) Extreme values of the negative (hogging) BM at supports:

• -32.45 kNm for the first interior support 'B' is obtained from case 4 where LL is applied on the spans
on either side of that support.
• -29.08 kNm for the second interior support 'C' is obtained from case 5 where LL is applied on the
spans on either side of that support.

In general, the extreme values of the negative BM at a support occurs when the LL is applied on the
spans on either side of that support and also on every alternate span thereafter.

'and also on every alternate span thereafter' in the above statement cannot be demonstrated in our
slab because it has only three spans. On a beam or slab which has more spans, it can be shown as in
fig.7.12 below:

Fig.7.12
Loading arrangement for maximum hogging moment at support B

(b) Extreme values of positive BM at center of spans:

• 28.44 kNm at the center of span AB is obtained from case 6 where the LL is applied on span AB itself
and also on span CD which is an alternate span.
• 12.9 kNm at the center of span BC is obtained from case 2 where LL is applied on span BC only.
• 25.45 kNm at the center of span CD is obtained from case 6 where the LL is applied on span CD itself
and also on span AB which is an alternate span.

In general, The maximum positive (sagging) moment in a span occurs when LL is applied on that span
and every other alternate span. On a beam or slab which has more spans, it can be shown as in
fig.7.13 below:

Fig.7.13
Loading arrangement for maximum sagging moment at midspan BC

(c)Minimum value of positive BM at center of spans:


• 6.8 kNm at the center of span AB is obtained from case2 where
1. LL is applied on the adjacent span which is BC and
2. No LL is applied on AB & CD.

• -7.7 kNm at the center of span BC is obtained from case6 where

https://limitstatelessons.blogspot.in/2013/12/chapter-7-analysis-of-continuous-one.html 6/8
4/20/2018 Reinforced Concrete Design: Chapter 7 - Analysis of continuous one-way slabs
1. LL is applied on the adjacent spans which are AB and CD
2. No LL is applied on BC.

• 5.33 kNm at the center of span CD is obtained from case2 where


1. LL is applied on the adjacent span which is BC and
2. No LL is applied on AB & CD.

In general, The minimum positive moment in a span occurs when

1. No LL is applied on that span but


2. LL is applied on the adjoining spans and every alternate span thereafter.

On a beam or slab which has more spans, it can be shown as in fig.7.13 below:

Fig.7.13
Loading arrangement for minimum sagging moment at midspan BC

It should be noted that this minimum positive moment may turn out to be the maximum negative
moment at the midspan. That is, the beam will be bending upwards. This has occurred in case 6 above
where a lightly loaded short span is placed in between two heavily loaded long spans

(d) Extreme values of total shear force at supports:


• 30.36 kN for the first end support 'A' is obtained from case6 where:
1. LL is applied on the span AB of which this support is a part and
2. LL is applied on the alternate span CD

• 78.56 kN (42.65 from the outer side plus 35.91 from the inner side) for the first interior support 'B' is
obtained from case4 where LL is applied on the spans on either side of that support.

• 74.6 kN (40.0 from the outer side plus 34.6 from the inner side) for the second interior support 'C' is
obtained from case5 where LL is applied on the spans on either side of that support.

• 28.66 kN for the last end support 'D' is obtained from case6 where
1. LL is applied on the span CD of which this support is a part and
2. LL is applied on the alternate span.

In general, the extreme values of the shear force at a support occurs when the LL is applied on the
spans on either side of that support and also on every alternate span thereafter. This is the same
condition for obtaining the extreme values of negative BM at supports (fig.7.12).

So we obtained some general conditions for the extreme values of BM and SF. We did this using an
example. But these general conditions can be obtained by using the principles of 'Influence lines' also.

In the next section we will discuss a simplified procedure given by the code.

PREVIOUS

NEXT

Copyright©2015 limitstatelessons.blogspot.in - All Rights Reserved

Posted by Nikhil Kumar at 10:53 PM

Labels: Analysis of continuous beams, Analysis of continuous one way slabs, Arrangement of loads, IS 456, Maximum bending
moment, Maximum shear force., method of coefficients

No comments:
Post a Comment

https://limitstatelessons.blogspot.in/2013/12/chapter-7-analysis-of-continuous-one.html 7/8
4/20/2018 Reinforced Concrete Design: Chapter 7 - Analysis of continuous one-way slabs

Enter your comment...

Comment as: Unknown (Goo Sign out

Publish Preview Notify me

Newer Post Home Older Post

Subscribe to: Post Comments (Atom)

Blog Archive

► 2016 (35)
► 2015 (99)
► 2014 (9)
▼ 2013 (6)
▼ December (3)
Chapter 7 - Analysis of continuous one-way slabs
Chapter 6 - Design of One-way slabs
Chapter 5 Analysis of One-way slabs

► October (1)
► September (2)

StatCounter

Powered by Blogger.

https://limitstatelessons.blogspot.in/2013/12/chapter-7-analysis-of-continuous-one.html 8/8

S-ar putea să vă placă și