Documente Academic
Documente Profesional
Documente Cultură
►General:
I. The design of slab is undertaken considering one panel at time. ►Loads to be consider:
Each panel is supported on all four sides with beams/girders.
→ Weight of slab
II. The Analysis two-way slab systems are established using Coefficient → Weight of ceilling
design method wherein a set of coefficiets is used to determine the → Weight tiles
design moments at critical sections. → Weight due to live load
→ Weight of covering
Case Description
1 All four edges discontinuous ►For Dead load
2 All four edges continuous
3 Two long edges discontinuous Material
4 One long and short edges discontinuous Reinforced Concrete (Table 2
5 Two short edges discontinuous Ceramic or quarry tile (Table 2
6 Two short and one long discontinuous Fibrous Glass (Table 204-2
7 Two long and one short discontinuos Bituminous gravel-covered (Tabl
8 One long edges discontinuous
9 One short edges discontinuous ►For Live load
III. Section 408.10.2.5 All loads shall be due to gravity only CATEGORY
and uniformly distributed over entire panel. Dinning rooms and Restaurants
(Table 205-1)
IV. Section 408.10.2.6 Unfactored live load shall not exceed Office ( Table 205-1)
two times the unfactored dead load.
Determination of Cover:
2.1 Design Data:
Assumed diameter of main reinforc
Assumed concrete compressive strength fć = 21 MPa Minimum cover for slab from Sect
Steel yield strength A955, fy = 280 MPa
Effective depth, da = thickness of s
Effective depth, db = thickness of s
In section 408.10.2.3 provides that the panel shall �_𝑠= 𝐶_𝐷𝐿 𝑊_𝑈𝐷𝐿 𝐿^2+ 𝐶
be rectangular with the ratio longer to shorter panel dimension,
measured center to center of supports not to exceed 2. where: CDL = Coefficient will
CLL = Coefficient will
Check the slab if it's One way slab or Two way slab.
Negative Moment at Discontinupus
[𝐿𝑙/𝐿𝑤=𝑅𝑎𝑡𝑖𝑜" " ] <2.0
Two way slab :
�_𝑑 = −1/3
�_𝑠
[𝐿𝑙/𝐿𝑤=𝑅𝑎𝑡𝑖𝑜" " ] >2.0
55
�_� = 0.85𝑓ć𝛽600/
∴ Thus, the panel is two-way slab system. (𝑓�(600+𝑓�))
�_𝑚𝑎� = 3/7
Negative Moment at Continuous Edges, Mc: [0.85𝑓ć𝛽/𝑓�]
Wu = 1.2DL + 1.6LL
Mc = -CWuL²
Where:
C = Coefficient will be obtained from the table
Shear coefficients
Table 2-5
where: Case no.: 1 2
β (NSCP 2015 Table 422.2.2.4.3) Ratio Wa Wb Wa
𝑚𝑖� = 1.4/𝑓� 1.000 0.500 0.500 0.500
if 17 ≤ f'c ≤ 28 use β=0.85 0.950 0.550 0.450 0.550
�_� = 0.85𝑓ć𝛽600/ 0.900 0.600 0.400 0.600
(𝑓�(600+𝑓�)) if 28 < f'c < 55 ((0.05(𝑓^′ 𝑐−28))/7) 0.850 0.660 0.340 0.660
use β=0.85
�_𝑚𝑎� = 3/7 0.800 0.710 0.290 0.710
[0.85𝑓ć𝛽/𝑓�] if f'c ≥ 55 use β=0.65 0.750 0.760 0.240 0.760
0.700 0.810 0.190 0.810
0.650 0.850 0.150 0.850
0.600 0.890 0.110 0.890
0.550 0.920 0.080 0.920
0.500 0.940 0.060 0.940
of reinforcement steel
SLAB CASE
at discontinuous edges
of reinforcement steel
discontinuous
59
at critical section
at other section
continues edges:
2 3 4 5 6 7 8
Cl Cs Cl Cs Cl Cs Cl Cs Cl Cs Cl Cs
0.045 0.000 0.076 0.050 0.050 0.075 0.000 0.071 0.000 0.000 0.071 0.033
0.041 0.000 0.072 0.055 0.045 0.079 0.000 0.075 0.000 0.000 0.067 0.038
0.037 0.000 0.070 0.060 0.040 0.800 0.000 0.079 0.000 0.000 0.062 0.043
0.031 0.000 0.065 0.066 0.034 0.082 0.000 0.083 0.000 0.000 0.057 0.049
0.027 0.000 0.061 0.071 0.029 0.083 0.000 0.086 0.000 0.000 0.051 0.055
0.022 0.000 0.056 0.076 0.024 0.085 0.000 0.088 0.000 0.000 0.044 0.061
0.017 0.000 0.050 0.081 0.019 0.086 0.000 0.091 0.000 0.000 0.038 0.068
0.014 0.000 0.043 0.085 0.015 0.087 0.000 0.093 0.000 0.000 0.031 0.074
0.010 0.000 0.035 0.089 0.011 0.088 0.000 0.095 0.000 0.000 0.024 0.080
0.007 0.000 0.028 0.092 0.008 0.089 0.000 0.096 0.000 0.000 0.019 0.085
0.006 0.000 0.022 0.094 0.006 0.090 0.000 0.097 0.000 0.000 0.014 0.089
ve Moments
2 3 4 5 6 7 8
Cl Cs Cl Cs Cl Cs Cl Cs Cl Cs Cl Cs
0.018 0.018 0.027 0.027 0.027 0.027 0.018 0.033 0.027 0.027 0.033 0.020
0.016 0.021 0.025 0.03 0.024 0.028 0.015 0.036 0.024 0.031 0.031 0.022
0.014 0.025 0.024 0.033 0.022 0.029 0.013 0.039 0.021 0.035 0.028 0.025
0.012 0.029 0.022 0.036 0.019 0.031 0.011 0.042 0.017 0.040 0.025 0.029
0.011 0.034 0.02 0.039 0.016 0.032 0.009 0.045 0.015 0.045 0.022 0.032
0.009 0.040 0.018 0.043 0.013 0.033 0.007 0.048 0.012 0.051 0.020 0.036
0.007 0.046 0.016 0.046 0.011 0.035 0.005 0.051 0.009 0.058 0.017 0.040
0.006 0.054 0.014 0.05 0.009 0.036 0.004 0.054 0.007 0.065 0.014 0.044
0.004 0.062 0.011 0.053 0.007 0.037 0.003 0.056 0.006 0.073 0.012 0.048
0.003 0.071 0.009 0.056 0.005 0.038 0.002 0.058 0.004 0.081 0.009 0.052
0.002 0.080 0.007 0.059 0.004 0.039 0.001 0.061 0.003 0.089 0.007 0.056
ve Moments
2 3 4 5 6 7 8
Cl Cs Cl Cs Cl Cs Cl Cs Cl Cs Cl Cs
0.027 0.027 0.032 0.032 0.032 0.032 0.027 0.035 0.032 0.032 0.035 0.028
0.025 0.031 0.029 0.035 0.029 0.034 0.024 0.038 0.029 0.036 0.032 0.031
0.022 0.035 0.027 0.039 0.026 0.037 0.021 0.042 0.025 0.040 0.029 0.035
0.019 0.040 0.024 0.043 0.023 0.041 0.019 0.046 0.022 0.045 0.026 0.040
0.017 0.045 0.022 0.048 0.020 0.044 0.016 0.051 0.019 0.051 0.023 0.044
0.014 0.051 0.019 0.052 0.016 0.047 0.013 0.055 0.016 0.056 0.020 0.049
61
0.012 0.057 0.014 0.057 0.014 0.051 0.011 0.060 0.013 0.063 0.017 0.054
0.010 0.064 0.016 0.062 0.011 0.055 0.009 0.064 0.010 0.070 0.014 0.059
0.007 0.071 0.011 0.067 0.009 0.059 0.007 0.068 0.008 0.077 0.011 0.065
0.006 0.080 0.009 0.072 0.007 0.063 0.005 0.073 0.006 0.085 0.009 0.070
0.004 0.088 0.007 0.077 0.005 0.067 0.004 0.078 0.005 0.092 0.007 0.076
ficients
3 4 5 6 7 8
Wb Wa Wb Wa Wb Wa Wb Wa Wb Wa Wb Wa
0.500 0.170 0.830 0.500 0.500 0.830 0.170 0.710 0.290 0.290 0.710 0.330
0.450 0.200 0.800 0.550 0.450 0.860 0.140 0.750 0.250 0.330 0.670 0.380
0.400 0.230 0.770 0.600 0.400 0.880 0.120 0.790 0.210 0.380 0.620 0.430
0.340 0.280 0.720 0.660 0.340 0.900 0.100 0.830 0.170 0.430 0.570 0.490
0.290 0.330 0.670 0.710 0.290 0.920 0.080 0.860 0.140 0.490 0.510 0.550
0.240 0.390 0.610 0.760 0.240 0.940 0.060 0.880 0.120 0.560 0.440 0.610
0.190 0.450 0.550 0.810 0.190 0.950 0.050 0.910 0.090 0.620 0.380 0.680
0.150 0.530 0.470 0.850 0.150 0.960 0.040 0.930 0.070 0.690 0.310 0.740
0.110 0.610 0.390 0.890 0.110 0.970 0.030 0.950 0.050 0.760 0.240 0.800
0.080 0.690 0.310 0.920 0.080 0.980 0.020 0.960 0.040 0.810 0.190 0.850
0.060 0.760 0.240 0.940 0.060 0.990 0.010 0.970 0.030 0.860 0.140 0.890
62
Case 9
one short edge discontinous
63
8 9
Cl Cs Cl
0.061 0.061 0.033
0.056 0.065 0.029
0.052 0.068 0.025
0.046 0.072 0.021
0.041 0.075 0.017
0.036 0.078 0.014
0.029 0.081 0.011
0.024 0.083 0.008
0.018 0.085 0.006
0.014 0.086 0.005
0.010 0.088 0.003
8 9
Cl Cs Cl
0.023 0.023 0.020
0.021 0.024 0.017
0.019 0.026 0.015
0.017 0.028 0.013
0.015 0.029 0.010
0.013 0.031 0.007
0.011 0.033 0.006
0.009 0.034 0.005
0.007 0.036 0.004
0.005 0.037 0.003
0.004 0.038 0.002
8 9
Cl Cs Cl
0.030 0.030 0.028
0.027 0.032 0.025
0.024 0.036 0.022
0.022 0.039 0.020
0.019 0.042 0.017
0.016 0.046 0.013
64
9
Wb Wa Wb
0.670 0.670 0.330
0.620 0.710 0.290
0.570 0.750 0.250
0.510 0.790 0.210
0.450 0.830 0.170
0.390 0.860 0.140
0.320 0.890 0.110
0.260 0.920 0.080
0.200 0.940 0.060
0.150 0.950 0.050
0.110 0.970 0.030
Case 4
ne long and one short
edges discontinuous
Case 8
long edge discontinuous
65