Documente Academic
Documente Profesional
Documente Cultură
Manual DEH-P2550/XM/ES
ORDER NO.
CRT2983
MULTI-CD CONTROL HIGH POWER CD PLAYER WITH FM/AM TUNER
- This service manual should be used together with the following manual(s):
Model No. Order No. Mech. Module Remarks
CX-3026 CRT2944 S10 CD Mech. Module:Circuit Description, Mech.Description, Disassembly
A SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.
In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
E
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,
proper cleaning should be performed to restore their performances.
To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or
the shipping screws should be installed before shipping out in accordance with this manual, if necessary.
2 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
CONTENTS A
SAFETY INFORMATION ............................................................................................................................................2
1. SPECIFICATIONS .......................................................................................................................................................4
2. EXPLODED VIEWS AND PARTS LIST.......................................................................................................................5
2.1 PACKING...............................................................................................................................................................5
2.2 EXTERIOR.............................................................................................................................................................6
2.3 CD MECHANISM MODULE .................................................................................................................................8
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ...................................................................................................10
3.1 BLOCK DIAGRAM ..............................................................................................................................................10
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE) ........................................................................................12
B
3.3 KEYBOARD UNIT ...............................................................................................................................................18
3.4 CD MECHANISM MODULE ...............................................................................................................................20
4. PCB CONNECTION DIAGRAM ................................................................................................................................24
4.1 TUNER AMP UNIT .............................................................................................................................................24
4.2 PANEL UNIT .......................................................................................................................................................28
4.3 KEYBOARD UNIT ...............................................................................................................................................29
4.4 CD MECHANISM MODULE ...............................................................................................................................30
5. ELECTRICAL PARTS LIST ........................................................................................................................................32
6. ADJUSTMENT .........................................................................................................................................................36
6.1 CD ADJUSTMENT .............................................................................................................................................36 C
DEH-P2550/XM/ES 3
5 6 7 8
1 2 3 4
A 1. SPECIFICATIONS
Backup current
B 5 mA or less
4 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
NOTE:
- Parts marked by “*” are generally unavailable because they are not in our Master Spare Parts List.
- Screws adjacent to ∇ mark on the product are used for disassembly.
- For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions, apply as you think it appropriate.)
D
- PACKING SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.
1 Cord Assy CDE7060 14 Bush CNV3930
2 Accessory Assy CEA3439 15 Polyethylene Bag CEG1173
3 Spring CBH1650 * 16 Battery CEX1065
4 Screw Assy CEA3437 17 Carton(DEH-P2550/XM/ES) CHG4961
5-1 Owner’s Manual CRD3690 Carton(DEH-P2550/XN/ES) CHG4975
9 Screw TRZ50P080FTC
* 10 Polyethylene Bag CEG-158
11 Handle CNC5395
12 Case Assy CXB3520)
13 Remote Control Unit CXC1265
DEH-P2550/XM/ES 5
5 6 7 8
1 2 3 4
2.2 EXTERIOR
6 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
DEH-P2550/XM/ES 7
5 6 7 8
1 2 3 4
B 1
2
1
C
2
1
2 1
1
2
D 1
3
1
2
2
1 1
1
1
1GEM1024
2GEM1045
3GEM1035
8 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
Mark No. Description Part No. Mark No. Description Part No.
1 CD Core Unit(S10) CWX2708 46 Rack CNV7199
2 Connector(CN101) CKS4182 47 Holder CNV7201
3 Connector(CN701) CKS4188 48 Holder CNV7202
4 Screw BMZ20P035FTC 49 Arm CNV7203
5 Screw BSZ20P040FTC 50 Gear CNV7207
91 Screw IMS26P030FMC
F
DEH-P2550/XM/ES 9
5 6 7 8
1 2 3 4
7 6 13 5 10 9 8 11 14 18 19 20 21
FM/AM TUNER UNIT
WC
CE2
ROM_VDD
SL
DI
CK
CE1
NC
DO
NC
NC
NC
NC
IC 3 EEPROM IC 5
←
5.0V 5V 3.3V
OSC LPF
B ANTENNA CN401
AM ANT FMRF
1
1 ATT
2 Rch
24
IC 2
IC 1 2.5V
FM ANT
3 3.3V
ATT Lch
23
FMRF MIXER, IF AMP DET, FM MPX
RF adj
ANT adj
T51 CF52
CF51
AUDIOGND
OSCGND
IC 4
VDD_3.3
RFGND
DGND
←
3.3V 3.3V 2.5V 2.5V
C
VCC
NC
2 12 15 22 16 4 17
CN101 CD L 4
7
11
5
BUZZER EVST,EVCK,EVDT
1
8
8
85
RX mute
37
IPPW 24
CN101 CN701 IPPW
LASER Q101 CN721
D DIODE LD+
14
1
LD LOUT
20 LOUT
8 14
MD 2 23 21
5 PD SYSPW
xtal
Q101
AC, F, E, BD X201
HOLOGRAM BU 16
24 X1
UNIT SERVO XTAL X601
CONTROL, SYSTEM CONTROLLER
FOP FOP 71 15
FOCUS ACT. 1 DSP, X2
TOP TOP ASENBO
MONITOR TRACKING ACT. 4 LPF, DAC IC 601(2/2)
Q601
DIODE IC 722 PE5341C
Q102 83
AVREF V
12 XSI 2 4 66
12 FD, TD, SD, MD IC 201 SO 16 6 XSI
13
FOP UPD63712GC 59
CDLOEJ 22
TOP 42 adpw
LIMIT TC7SET08FU 61
CONT
SPINDLE
ACT,MOTOR 79
MOTOR M DRIVER DSCSNS
FLPILM
9
HOME CLMP 63
16 XTALEN 8
SOP
15 80 VDSENS ejectin
SOM
17
LOADING/ CARRIAGE LCOM
M 18 22 LOEJ
VDCONT
DPDT
9 CONT
CONT 7 15 BU
64 95 90 96 41 20
IC 301
E BA5996FP
DSCSNS
6 16
CLMP
11 11
VDD
VDSENS Q752
VD
CLAMP VD 1 20 BU
12EJ 8EJ DSCSNS 2 21
3.3V REGULATOR
3 1
3R3V
IC 701 Q751 S
NJM2391DL1-33
DETACH SENSE
10 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
RESET
1 IC 651 2
VDD
BD4834G
Q351
CE2 32
TUNPCE2
CE1 99
TUNPCE1
DO 94
TUNPDI
DI 98
TUNPDO
CK 97
TUNPCK VDD REGULATOR
Q901
74 SL VDD
Q902 B
SYSTEM CONTROLLER
IC 601(1/2) 10
PE5341C DALMON
CN981
BACKUP SENSE BU
93 FUSE
bsens 16 16 BACK UP
BU
10A
Q931
92 ACC
asens 14 14 ACC
ACC SENSE
15 15 GND
C
BU
ELECTRONIC VOLUME/
SOURCE SELECTOR POWER AMP 20
TUN L 3
IN2-L 23
+L 5 IN4+L FL- 7 7 FL-
21
-L 6 IN4-L IC 131 10 14 IC 301 FL+ 5 5 FL+
FL FLIN PAL007A 3
PML003AM 11 12 RL- 8 8 RL-
RL RLIN 5
4
IN3-L
RL+ 6 6 RL+
MUTE STBY B.REMOTE
22 4 25
11 11 B.REM
VST,EVCK,EVDT
MUTE
Q502
BU SYS 8.4V REGULATOR
Q911 Q912
SYS 8.4V BU
MUTE
Q301
Q501 Q913
D
SYSPW
BA033FP
Q601
VDD
CN831
BU 5 5
Q831
6 6
8 8
S1970
B PANEL UNIT C KEYBOARD UNIT
9 9
EJECT CN1901
Q961
ILB ILB
BU 7 7 4 9
BL+B
10 10 5 8
E
Q962
Q971
SWDVDD SWVDD
VDD 2 2 2 11
S801 17 55 11
RFM
VLCD
VDD
CN1951
CN1950
F
DEH-P2550/XM/ES 11
5 6 7 8
1 2 3 4
CD:0dBs
D CN701
IP-BUS:+2.2dBs
IP-BUS
C
R9101
0R0
PE5
FM(30%):-30.0dBs
AM(30%):-30.0dBs
D
FM/AM TUNER UNIT
R9403
0R0
E
DETACH SENSE SW
EJECT
C
CN1901
F PANEL
B UNIT
12 A B DEH-P2550/XM/ES
3 4
1 2
5 6 7 8
A-b A
FM:-6.66dBs
AM:-6.66dBs
IP-BUS:+9.54dBs
CD:+9.34dBs
FM:-5.9dBs B
REAR
AM:-5.9dBs R CH
IP-BUS:+10.3dBs
REAR
CD:+10.1dBs L CH
5341C
>
FUSE
600µH 10A
CEK1208
BACKUP D
GND
ACC
B.REM
RL—
FL—
RL+
FL+
RR—
FR—
RR+
FR+
FM:+30dBs
AM:+20dBs
IP-BUS:+36dBs
CD:+36dBs
NOTE :
Symbol indicates a resistor. Decimal points for resistor
No differentiation is made between chip resistors and and capacitor fixed values
discrete resistors. are expressed as :
Symbol indicates a capacitor. 2.2 ← 2R2
No differentiation is made between chip capacitors and 0.022 ← R022
discrete capacitors.
DEH-P2550/XM/ES A 13
5 6 7 8
F
E
B
A
D
C
14
A-a A-b
1
1
A-a
A-b
1
2
2
FM:-31.0dBs
R4721 AM:-31.0dBs
IP-BUS:+2.2dBs
0R0
CD:0dBs
DEH-P2550/XM/ES
CD:0dBs
3
3
D CN701
IP-BUS:+2.2dBs
IP-BUS
4
4
R9101
0R0
PE5341C
FM(30%):-30.0dBs
AM(30%):-30.0dBs
5
5
R9403
0R0
6
6
DETACH SENSE SW
DEH-P2550/XM/ES
EJECT
7
7
CN1901
PANEL
4
B UNIT
8
8
A-a A-b
A-a B
A-b
15
F
E
B
A
D
C
F
E
B
A
D
C
16
A-a A-b
1
1
A-b
A TUNER AMP UNIT
2
2
FM:-6.66dBs
AM:-6.66dBs
IP-BUS:+9.54dBs
CD:+9.34dBs
FM:-5.9dBs
REAR
AM:-5.9dBs R CH
IP-BUS:+10.3dBs
REAR
CD:+10.1dBs L CH
DEH-P2550/XM/ES
3
3
4
4
1C
>
FUSE
600µH 10A
CEK1208
BACK
5
5
B.RE
RL—
FL—
RL+
FL+
RR—
FR—
RR+
FR+
FM:+30dBs
AM:+20dBs
IP-BUS:+36dBs
CD:+36dBs
6
6
DEH-P2550/XM/ES
7
7
NOTE :
Symbol indicates a resistor. Decimal points for resistor
No differentiation is made between chip resistors and and capacitor fixed values
discrete resistors. are expressed as :
Symbol indicates a capacitor. 2.2 ← 2R2
No differentiation is made between chip capacitors and 0.022 ← R022
discrete capacitors.
4
Therefore, when replacing, be sure to use parts of
identical designation.
8
8
A-a A-b
A-b
17
F
E
B
A
D
C
1 2 3 4
A
3.3 KEYBOARD UNIT
C KEYBOARD UNIT
B
CAW1759
C
18 DEH-P2550/XM/ES
1 2 3 4
5
5
6
6
SML-310PT x12
150
150
DEH-P2550/XM/ES
150
150
7
7
CEL1651
CEL1651
8
8
B CN1951
C
19
F
E
B
A
D
C
1 2 3 4
A Pickup Unit(Service)(P10)
F F
T T
B
T T
F F F
T T
T T F
F F T
F F T
!
C
0
1
9
MOTOR DRIVER
@
S
T
SPINDLE MOTOR 7 5
S C
M1 CXB6007 S F
LOADING/CARRIAGE 8
E MOTOR C 6
M2 CXB8933
C 3
F
F
C
T
C
T
S
S
3.3V
REGULATOR
D
20 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
SIGNAL LINE
F
FOCUS SERVO LINE
T
TRACKING SERVO LINE
C CARRIAGE SERVO LINE
S SPINDLE SERVO LINE
T
S
F
SWITCHES: B
CD CORE UNIT
S901 : HOME SWITCH.....ON-OFF
S902 : CLAMP SWITCH....ON-OFF
S903 : DSCSNS SWITCH....ON-OFF
RF AMP / SERVO / DSP S904 : 12EJ SWITCH....ON-OFF
S905 : 8EJ SWITCH....ON-OFF
DAC / LPF The underlined indicates the switch position.
D
4
A CN721
CN???
2
5
C
E
3
$%
D
DEH-P2550/XM/ES 21
5 6 7 8
1 2 3 4
- Waveforms Note : 1. The encircled numbers denote measuring points in the circuit diagram.
A 2. Reference voltage REFO1(1.65V)
1 DSCSNS 5V/div 500ms/div 1 DSCSNS 5V/div 500ms/div 5 SIN 1V/div 2s/div
2 CLCONT 5V/div 2 CLCONT 5V/div 6 CIN 500mV/div
3 LOEJ 5V/div 3 LOEJ 5V/div 7 TIN 500mV/div
4 VD 10V/div 4 VD 10V/div When setting up after loading a 12cm CD-DA
When loading a 12cm CD When loading an 8cm CD disc
B
Mode: Mode: Mode:
Normal Normal Normal
C
Ref.: Ref.: Ref.:
REFO REFO REFO
D
Spindle waveform during "Play" Spindle waveform during "Play"(Magnified) RF eye pattern
22 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
B
Mode: Mode: Mode:
TEST TEST Normal
C
Ref.: Ref.: Ref.:
REFO REFO REFO
DEH-P2550/XM/ES 23
5 6 7 8
1 2 3 4
SIDE B
P.C.Board Chip Part
L981
R9101
R4721
D CN701
E
DETACH SENSE
F
A
24 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
SIDE A
IC,Q
PRE OUT
ANTENNA
R9403
B CN1950
F
FRONT
A
DEH-P2550/XM/ES 25
5 6 7 8
1 2 3 4
A
A TUNER AMP UNIT
IC,Q
A
26 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
A
SIDE B
A
DEH-P2550/XM/ES 27
5 6 7 8
1 2 3 4
C CN1901
EJECT
A CN831
B
28 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
A
IC,Q
IC,Q ↓
↓
↓
AUDIO
B CN1951
↓
PAUSE
FUNC
B
BAND/ESC
LOUD
C
6
5
4
D
3
2
1
E
SRC
DISP
↓
↓
EQ
F
CLK
C
DEH-P2550/XM/ES 29
5 6 7 8
1 2 3 4
M2
LOADING
/CARRIAGE MOTOR
B
M1
SPINDLE MOTOR
A
CN721
CN???
D
HOME
PICKUP UNIT
(SERVICE)(P10)
D
30 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
A
8EJ 12EJ
DSCSNS
CLAMP
D
DEH-P2550/XM/ES 31
5 6 7 8
1 2 3 4
32 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
=====Circuit Symbol and No.===Part Name Part No. =====Circuit Symbol and No.===Part Name Part No.
--- ------ ------------------------------------------ ------------------------- --- ------ ------------------------------------------ ------------------------- A
R 619 RS1/16S1602D R 965 RS1/16S182J
R 620 RS1/16S473J R 971 RS1/16S153J
R 621 RS1/16S473J R 972 RS1/16S153J
R 622 RS1/16S473J R 973 RS1/16S222J
R 623 RS1/16S473J R 981 RD1/4PU102J
DEH-P2550/XM/ES 33
5 6 7 8
1 2 3 4
=====Circuit Symbol and No.===Part Name Part No. =====Circuit Symbol and No.===Part Name Part No.
A --- ------ ------------------------------------------ ------------------------- --- ------ ------------------------------------------ -------------------------
C 911 CEJQ221M10 Unit Number : CWM8758
C
C
912
913
CKSRYB103K50
CEJQ101M16
B Unit Name : Panel Unit
C 921 CEJQ220M10
C 922 CKSRYB103K50
MISCELLANEOUS
D 1970 LED CL220PGC
C 923 CKSYB475K10
S 1970 Push Switch(EJECT) CSG1112
C 931 CKSRYB104K25
C 961 CKSRYB473K50
RESISTORS
34 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
R 508 RS1/16S221J
R 509 RS1/16S221J
R 601 RS1/16S101J
R 602 RS1/16S101J
R 603 RS1/16S0R0J
R 901 RS1/16S104J
R 902 RS1/16S473J
R 903 RS1/16S273J B
CAPACITORS
C 101 CKSRYB104K16
C 102 CKSRYB104K16
C 103 100µF/16V CCH1504
C 104 47µF/6.3V CCH1506
C 106 CCSRCH101J50
C 108 CKSRYB224K16
C 109 CKSRYB224K16
C 201 CKSRYB104K16
C 202 CKSRYB471K50
C 203 CKSRYB104K16
C 210 CKSRYB104K16
C 211 CKSRYB104K16
C 212 CKSRYB104K16
C 213 CKSRYB332K50
C 214 CKSRYB473K25
C 215 CKSRYB104K16
C 216 CKSRYB103K25
C 217 CCSRCH560J50
C 218 CCSRCH5R0C50
C 219 CKSRYB104K16 D
C 220 CKSRYB104K16
C 221 CKSRYB104K16
C 222 CKSRYB103K25
C 223 CCSRCH680J50
C 224 CCSRCH470J50
C 225 CKSRYB682K50
C 231 CKSRYB102K50
C 232 CKSRYB102K50
C 301 100µF/16V CCH1504
C 302 CCSRCH221J50
C 303 CCSRCH221J50
C 304 CKSRYB472K50
C 305 CKSRYB103K25 E
C 306 CKSRYB104K16
C 501 CKSRYB103K25
C 502 CKSRYB103K25
C 702 100µF/16V CCH1504
C 703 CKSRYB224K16
C 704 CKSRYB104K16
C 705 10µF/6.3V CCH1470
DEH-P2550/XM/ES 35
5 6 7 8
1 2 3 4
6. ADJUSTMENT
6.1 CD ADJUSTMENT
A
1) Cautions on adjustments 2) Test mode
• In this product the single voltage (3.3V) is used for the This mode is used to adjust the CD mechanism module.
regulator. The reference voltage is the REFO1 (1.65V) • To enter the test mode.
instead of the GND. While pressing the 4 and 6 keys at the same time, reset.
If you should mistakenly short the REFO1 with the GND • To exit from the test mode.
during adjustment, accurate voltage will not be obtained, Turn off the ACC and back up.
and the servo’s misoperation will apply excessive shock
to the pickup. To avoid such problems: Notes:
a. Do not mix up the REFO1 with the GND when a. During ejection, do not press any other keys than the
connecting the (-) probe of measuring instruments. EJECT key until the loaded disc is ejected.
Especially on an oscilloscope, avoid connecting the (-) b. If you have pressed the (→) key or (←) key during focus
B probe for CH1 to the GND. search, turn off the power immediately to protect the
b. In many cases, measuring instruments have the same actuator from damage caused by the lens stuck.
potential as that for the (-) probe. Be sure to set the c. For the TR jump modes except 100TR, the track jump
measuring instruments to the floating state. operation will continue even if the key is released.
c. If you have mistakenly connected the REFO1 to the GND, d. For the CRG move and 100TR jump modes, the tracking
turn off the regulator or the power immediately. loop will be closed at the same time when the key is
released.
• Before mounting and removing filters or leads for e. When the power is turned off and on, the jump mode
adjustment, be sure to turn off the regulator. is reset to the single TR (91), the RF amp gain is set to 0dB,
and the auto-adjustment values are reset to the default
• For stable circuit operation, keep the mechanism settings.
operating for about one minute or more after the
C regulator is turned on.
36 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
- Flow Chart A
[KEY] [4]+[6]+Reset
Test Mode In
Contents
Display
[CD]or[SOURCE]
Source On
TRK MIN
[BAND] [3]
Power On Power On B
(T.Offset is adjusted) (T.Offset is not adjusted)
TRK 00 MIN00 SEC 00 TRK 99 MIN 99 SEC 99
[BAND] [2]
DEH-P2550/XM/ES 37
5 6 7 8
1 2 3 4
A • Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism
module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU
unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the
PU unit must be changed, the grating should be checked using the procedure below.
• Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.
• Symptoms of Mal-adjustment :
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
B
track search operations, or taking a long time for track searching.
• Method :
• Measuring Equipment • Oscilloscope, Two L.P.F.
• Measuring Points • E, F, REFO1
• Disc • ABEX TCD-782
• Mode • TEST MODE
CD CORE UNIT(S10)
C L.P.F.
Xch Ych
E 100kΩ
Oscilloscope
VREF 390pF
F 100kΩ
VREF 390pF
L.P.F.
REFO1
D
F
E
• Checking Procedure
1. In test mode, load the disc and switch the 3V regulator on.
2. Using the → and ← buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance
adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the
fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase
difference is within 75° . Refer to the photographs supplied to determine the phase angle.
E 5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the
mechanism should be judged to be at fault.
• Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the
average angle.
• Hint
Reloading the disc changes the clamp position and may decrease the "wobble".
38 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
0° 30°
45° 60°
C
75° 90°
DEH-P2550/XM/ES 39
5 6 7 8
1 2 3 4
- Error Messages
A
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of
the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from
the users and also for facilitating trouble analysis and repair work in servicing.
40 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 DISASSEMBLY A
B
Disconnect the connector and then remove the
CD Mechanism Module. 1
1
C
2 1 2
Grille Assy
Fig.1
3 3 3
Fig.2
DEH-P2550/XM/ES 41
5 6 7 8
1 2 3 4
Do not squeeze.
Carriage Mechanism
B C
A
Damper
Lower Frame
Damper
D B Damper
F
Inner Holder
Planet Gear
42 DEH-P2550/XM/ES
1 2 3 4
5
5
1 3 5 7 9 11 13 15
2 4 6 8 10 12 14 16
8 9 10 11
5 6 7
6
6
1 2 3 4
10A
1. FR+ 9. NC 1. BUS+
7.1.2 CONNECTOR FUNCTION DESCRIPTION
DEH-P2550/XM/ES
3. FR- 11. B.REM 3. GND
4. RR+ 12. NC 4. NC
5. FL+ 13. NC 5. BUS-
6. RL+ 14. ACC 6. GND
7
7
8
8
43
F
E
B
A
D
C
1 2 3 4
7.2 PARTS
7.2.1 IC
A
- Pin Functions(PE5341C)
Pin No. Pin Name I/O Format Function and Operation
1 swvdd O C Grille : Chip enable output
2-4 NC Not used
5 TESTIN I Test program mode input
6 LCDPW O C LCD back light power supply control output
7 TELIN I Telephone mute input
8 ejectin I Eject sense input
9 FLPILM I Flap illumination input
10 DALMON I/O C For consumption low-current
11 reset I Reset input
12 XT2 Not used
B 13 XT1 I Clock connection pin
14 VSS GND
15 X2 Crystal oscillator connection pin
16 X1 I Crystal oscillator connection pin
17 REGOFF I Regulator operation specification signal
18 REGC Capacitor for regulator connect pin
19 VDD Power supply
20 ILMPW O Illumination power supply control output
21 SYSPW O C System power control output
22 adpw O C A/D converter power supply control output
23 NC Not used
24 IPPW O C Power supply control output for IP BUS interface IC
C
25 NC Not used
26 ROMDATA O C ROM correction data output
27 ROMCLK O C ROM correction clock output
28 ROMCS O ROM correction chip select output
29-31 NC Not used
32 tunpce@ O PLL chip enable output2
33 VST O E.VOL : Strobe output
34 VCK O E.VOL : Clock output
35 VDT O E.VOL : Data output
36 ANTPW O Antenna power output
37 MUTE O C System mute output
D 38, 39 NC Not used
40 VSS GND
41 VDD Power supply
42 RDS57K I 57kHz count pulse input
43 drst O C RDS : Decoder reset output
44 rdslk I C RDS : Decoder clock input
45 RDT O C RDS : Decoder data input
46 DORAON O C TUNER : 3V power supply
47-57 NC Not used
58 STRKEY2 I Steering remote controller input
59 CDLOEJ O C CD : Load Moter Load/Eject output
60 CLCONT I CD : Driver input switch output
E 61 CONT O C CD : Servo driver power supply control output
62 PCL O C Clock adjustment
63 CLAMPSW I Clamp SW input
64 VDCONT O C CD : VD power control output
65 xsck(TSCK) O CD LSI clock output
66 XSI(TSI) I CD LSI data input
67 XSO(TSO) O C CD LSI data output
68 XAO O C CD LSI command/data control output
69 xrst O C CD : LSI reset control output
70 xstb O CD LSI strobe output
71 ASENBO O IP-BUS : Slave power supply control output
72 EMUTE O E.VOL : Mute control output
F
73 TEST GND
74 SL I C TUNER : Signal level input
75 STRKEY1 I C Steering remote controller input
44 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
* PE5341C
31
Format Meaning
C CMOS
BD4834G
80 1
N.C.
N.C.
100
81
E
5 4
Vref
1 2 3
F
VOUT
VDD
GND
DEH-P2550/XM/ES 45
5 6 7 8
1 2 3 4
PAL007A
A
sw_vcc
Protector;
Over voltage
1
TAB Reference
amp_vcc
Stand-by
2
P-GND2 Circuit
+-
3
OUT2-
B
Offset Protector;
4
-+
5
OUT2+
6
VCC
+-
7
OUT1-
Offset
8
P-GND1 Detection
-+
9
OUT1+
10
SVR
C
11
IN1
12 13
IN2
amp_vcc
Protector;
S-GND Short circuit
14
IN4
15
IN3
16
AC-GND
17
+-
OUT3+
18
Offset
D P-GND3 Detection
19
-+
OUT3-
20 21
VCC
+-
OUT4+
22
Offset
MUTE Detection
23
-+
OUT4-
24 25
P-GND4
SWITCH
E
sw_vcc
stby
Protector;
Over current limit
Mute circuit
46 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
C
*PD6340A
33
48
32 49
17 64 TSOP4840SB1
16
Control
Input Circuit
E
Band Demodu-
PIN AGC Pass lator
1 2 3
OUT GND VCC F
DEH-P2550/XM/ES 47
5 6 7 8
1 2 3 4
- Pin Functions(UPD63712GC)
A Pin No. Pin Name I/O Function and Operation
1 LD O Output of LD
2 PD I Input of PD
3 PN I Assignment of pickup polarity
4 AVDD Power supply for the analog system
5 DGND Ground for digital circuits
6 RFOK O Output of RFOK
7 INTQ O Interruption signals to the external microcomputer
8 rst I Input of reset
9 A0 I Command/Parameter discrimination signal input
10 stb I Data strobe signal input
11 sck I Serial data clock input
B
12 SO O Serial data output
13 SI I Serial data input
14 DVDD Power supply for digital circuits
15 DAVDD Power supply for DAC
16 ROUT O Output of audio for the right channel
17 DAGND GND for DAC
18 REGC Connected to the capacitor for band gap
19 DAGND GND for DAC
20 LOUT O Output of audio for the left channel
21 DAVDD Power supply for DAC
22 XVDD Power supply for the crystal oscillator
C 23 xtal O Connected to the crystal oscillator
24 XTAL I Connected to the crystal oscillator
25 XGND Ground for the crystal oscillator
26 DVDD Power supply for digital circuits
27 C1D1 O Information on error correction
28 C1D2 O Information on error correction
29 C2D1 O Information on error correction
30 C2D2 O Information on error correction
31 C2D3 O Information on error correction
32 LOCK O Output of LOCK
33 MIRR O MIRR signal
34 HOLD O HOLD signal
D 35 PLCK O Output of PLCK
36 C16M O Output of 16.9344MHz
37 DGND Ground for digital circuits
38 TX O DAI output
39 EMPH O Pre-emphasis information output
40 FLAG O The flag for which output sound data cannot be corrected is outputted
41 DVDD Power supply for digital circuits
42 LIMIT I Signal is inputted when the register can be read
43 xtalen I Permission to oscillate
44 DGND Ground for digital circuits
45 DIN I Input of audio data
E 46 DOUT O Output of audio data
47 SCKIN I Clock input for audio data
48 SCKO O Clock output for audio data
49 LRCKIN I Input of LRCK for audio data
50 LRCK O Output LRCK for audio data
51 DVDD Power supply for digital circuits
52 FD+ O Output of focus drive PWM
53 FD- O Output of focus drive PWM
54 TD+ O Output of tracking drive PWM
55 TD- O Output of tracking drive PWM
56 SD+ O Output of thread drive PWM
57 SD- O Output of thread drive PWM
F 58 MD+ O Output of spindle drive PWM
59 MD- O Output of spindle drive PWM
60 DGND Ground for digital circuits
48 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
* UPD63712GC
50
26
51 25
75 1
100
76
DEH-P2550/XM/ES 49
5 6 7 8
1 2 3 4
- Pin Functions(BA5996FP)
A Pin No. Pin Name Function and Operation
1 VR Input pin for reference voltage
2 OPIN2(+) Input pin for non-inverting input for CH2 preamplifier
3 OPIN2(-) Input pin for inverting input for CH2 preamplifier
4 OPOUT2 Output pin for CH2 preamplifier
5 OPIN1(+) Input pin for non-inverting input for CH1 preamplifier
6 OPIN1(-) Input pin for inverting input from CH1 preamplifier
7 OPOUT1 Output pin for CH1 preamplifier
8 GND Ground pin
9 MUTE Mute control pin
10 POWVCC1 Power supply pin for CH1, CH2, and CH3 at "Power" stage
11 VO1(-) Driver CH1 - Negative output
B
12 VO1(+) Driver CH2 - Positive output
13 VO2(-) Driver CH2 - Negative output
14 VO2(+) Driver CH2 - Positive output
15 VO3(+) Driver CH2 - Positive output
16 VO3(-) Driver CH2 - Negative output
17 VO4(+) Driver CH4 - Positive output
18 VO4(-) Driver CH4 - Negative output
19 POWVCC2 Power supply pin for CH4 at "Power" stage
20 GND Ground pin
21 CNT Control pin
22 LDIN Loading input
C 23 OPOUTSL Output pin for preamplifier for thread
24 OPINLSL Input pin for preamplifier for thread
25 OPOUT3 CH3 preamplifier output pin
26 OPIN3(-) Input pin for inverting input for CH3 preamplifier
27 OPIN3(+) Input pin for non-inverting input for CH3 preamplifier
28 PREVCC PreVcc
BA5996FP
NJM2391DL1-33
14 1
D
15 28
+-
VREF
E
1 2 3
F IN GND OUT
50 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
WC
CE2
ROM_VDD
SL
DI
CK
CE1
DO
NC
NC
NC
NC
NC
IC 3 EEPROM IC 5
←
5.0V 5V 3.3V
OSC LPF
AM ANT FMRF
1 ATT
Rch
24
IC 2
IC 1 2.5V B
FM ANT
3 3.3V
ATT Lch
23
FMRF MIXER, IF AMP DET, FM MPX
RF adj
ANT adj
T51 CF52
CF51
AUDIOGND
IC 4
OSCGND
VDD_3.3
←
RFGND
VCC
NC
2 12 15 22 16 4 17
C
DEH-P2550/XM/ES 51
5 6 7 8
4 3 2 1
DEH-P2550/XM/ES 52
SEG39
SEG38
F
SEG37
SEG36
COMMON
SEGMENT
COM3 COM3
COM2 COM2
COM1 COM1
COM0 COM0
SEG35
SEG34
SEG33 E
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25 D
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
C
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8 B
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
SEG0 A
- LCD(CAW1759)
7.2.2 DISPLAY
4 3 2 1
5 6 7 8
Power ON A
VDD=5V
Pin 41
bsens
Pin 93
B
bsens=L
asens
Pin 92
asens=L
dsens
Pin 90
C
dsens=L
ASENBO←H
Pin 71
CSENS
- CSENS <= 2V, 3V <
= CSENS
Pin 77
Last source returns.
2V < CSENS < 3V CD loading functions are available.
Starts Keys except for EJECT key are not available. D
communication
with Grille
microcomputer. 300ms
swvdd←H
Pin 1 300ms
Source ON
SYSPW←H
Pin 21
F
Completes power-on operation.
(After that, proceed to each source operation)
DEH-P2550/XM/ES 53
5 6 7 8
1 2 3 4
7.4 CLEANING
54 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
8. OPERATIONS
DEH-P2550/XM/ES 55
5 6 7 8
1 2 3 4
56 DEH-P2550/XM/ES
1 2 3 4
5 6 7 8
DEH-P2550/XM/ES 57
5 6 7 8
F
E
B
A
D
C
Fixing the Front Panel
58
If you do not operate the Detaching and Replacing the Front Panel Function, use the supplied fixing screws
and fix the front panel to this unit.
1
1
Holder CXX1644
2. Replace the front panel to the unit.
2
2
DEH-P2550/XM/ES
3
3
4
4
11. Connecting cords with RCA pin plugs
1. This Product (sold separately)
12. Power amp
5
5
13. Blue/white
To system control terminal of the power amp
or Auto-antenna relay control terminal (max.
300mA 12 V DC).
14. System remote control
6
6
DEH-P2550/XM/ES
ignition switch position. 20. Left 21. Right
23. Green 25. Violet
7
7
8. Red
To electric terminal controlled by ignition switch 24. Green/black 26. Violet/black
(12 V DC) ON/OFF.
9. Black (ground)
To vehicle (metal) body. 27. Rear speaker 27. Rear speaker
28. With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.
8
8
59
F
E
B
A
D
C