Documente Academic
Documente Profesional
Documente Cultură
(:f+T ;\-r”)
:
I.. :,._ :;\,;‘)
‘~“” ,y:I a y ,~:cal$j1364 ( Part 1 ) : 1gg2
Is0 4014 : 1988
Indian Standard
HEXAGON HEAD BOLTS, SCREWS AND NUTS
OF PRODUCT GRADES A AND B
PART 1 HEXAGON HEAD BOLTS
( SIZE RANGE Ml’6 TO M64 )
( Third Revision /
UDC 621’882’662
OBlS 1992
NATIONAL FOREWORD
This Indian Standard ( Part 1 ) which is identical with IS0 4014 : 1988 ‘Hexagon head bolts -
Product grades A and B’ issued by the International Organization for Standardization ( IS0 ) was
adopted by the Bureau of Indian Standards on the recommendation of the Bolts, Nuts and
Fastener Accessories Sectional Committee ( LM 14 ) and approval of the Light Mechanical
Engineering Division Council.
The standard was originally published in 1960 and revised in 1967. Subsequent to the
publication of 1967 edition, many changes had been agreed upon at international level which
have been reflected in IS 1367 series of standards covering ‘Technical supply conditions for
threaded steel fasteners’. Accordingly, the standard was published in 5 parts covering hexagon
head bolts, hexagon head screws, hexagon nuts, hexagon thin nuts ( chamfered ) and hexagon
thin nuts ( unchamfered ).
The second revision of the standard was based on IS0 4014 : 1979 ‘Hexagon head bolts of
Produc: grades A and 6’ issued by ISO. This third revision has been made by the adoption of
latest version of IS0 4014 published in 1988 as Part 1. The renGning parts of the standard
from Part 2 to Part 5 have also been revised by adoption of corresponding latest version of
International Standards. The following major changes Ihave been made in this revision:
a) The range of sizes has been enlarged to cover sizes from M 1‘6 to M64;
b) The range of nominal lengths has been extended up to 500 mm;
c) Non-preferred sizes have been included in separate table in line with IS0 4014;
d) Stainless steel bolts with property classas A2-70 and A2-50 have been included; and
e) The use of property classes like 4.6, 4.8, 5.8, 6.8 and 9.8 are also permitted subject to
the agreement between the manufacturer and user.
ln the 1967 version of this standard, the width across fiats for M 10 and Ml 2 size fasteners was
soecified as 17 mm and 19 mm respectively. However, in the 1983 version this width across
fiats was brought in line with IS0 4014 : 1979 and specified as 16 n?n! and 18 mm respectively
for MiO and Ml2 size fasteners. Recognizing the fact that the new width across flat dimensions
could not be implemented immediately, the Explanatory Note to 1983 version of the standard
made a reference to this aspect. However, in the absence of specific coverage in the standard,
the new width across flat dimensions could not be implemented. Recognizing the difficulty of
immediate changeover to new width acr& flats, the Committee felt that definite time frame
may ba given to the manufacturers for changeover and accordingly, it has been decided that
width across flats as per 1967 version, that is, 17 mm and 19 mm for Ml 0 and 12 size fasteners
shall be permitted till 31 December 1994.
It is also understood that some manufacturers are already equipped and manufacturing as per
new width across flat dimensions and supplies as per ney specifications are encouraged. During
this period, the manufacture of fasteners as per old versions shzll be phased out and by
1 January 1995, it is expcctad that the entire fastener industry would have switched over to
new width dimensions across flats and no old width across flats shall be permitted.
In the adopted standard, certain terminology and conventions are not identical with those used
in Indian Standards; attention is specially drawn to the following:
a) Wherever the words ‘International Standard’ appear, referring to this standard, they
should be read as ‘Indian Standard’; and
b) Ccmma ( , ) has been used as a decimal marker while in Indian Standards the current
practice is to use point ( ) as the decimal marker.
Indian Standard
HEXAGON HEAD BOLTS, SCREWS AND NUTS
OF PRODUCT GRADES A AND B
PART 1 HEXAGON HEAD BOLTS
( SIZE RANGE Ml.6 TO iU64 )
( Third Revision )
0 introduction
This international Standard is part of the complete IS0 product standard series on hexagon drive fasteners. The series comprises:
a) hexagon head bolts US0 4014, IS0 4015, IS0 4016 and IS0 8765);
bl hexagon head screws (IS0 4017, IS0 4018 and IS0 8676);
cl hexagon nuts IISO 4032, IS0 4033, IS0 4034, IS0 4035. IS0 4036, IS0 8673, IS0 8574 and IS0 86753;
f) hexagon flanged nuts (IS0 4161, IS0 7043 and IS0 7044);
g) s:rwxural bolting (IS0 4775, IS0 7411 to IS0 7414 and IS0 7417).
This International Standard gives specifications for hexagon head bolts with threads from Ml,6 up to and including M64, of product
grade A for threads Ml,6 to M24 and nominal lengths up to and including 10 d or 150 mm, whichever is shorter and product grade B
for threads over M24 or nominal lengths over 10 d or 150 mm, whichever is shorter.
if, in special cases, specifications other than those listed in this International Standard are required, t&q should b+ &&ed from
existing International Standards, for example IS0 261, IS0 868, IS0 89&l, IS0 966-Z. IS0 3506 and IS0 4759.1.
1
.s 1564 (Part , ) : 1692
IS0 4014 : 1988
2 Referm+s
I60 226, Fasteners - Bolts, screwS end nuts - Symbols and designations of dimensions.
IS0 888. Bolts, screns end studs - Nominal lengths and thread lengths for general purpose bolts and screws.
IS0 9652. IS0 generai purpose metric screw threads - Tolemnces -- Pert 2: Limits of sizes for general purpose bolt and nut
threeds - Medium quality.
~ISO 4753. Fasteners - Ends of parts with external metric IS0 thread.
IS0 47541, Tolerences for fasteners - Pert I: Bolts, screws end nuts with thread diameters > 1.6 end c 150 mm and product
grades A,’ E and C.
IS0 6lR-1. Fasteners - Swfece discontinoities - Part 1: SoIts, scn?ws end studs for general requirements.”
IS0 61673, Festeners - Sutfece discontinuities - F’eii3: Bolts, screws and studs for special requirements.“.
IS0 8839. Mechenicel properties of fasteners - Bolts, screws, studs end nuts made of non-ferrous metals.
16.0 8992. Fasteners - General requirements for bolts, screws and nuts.
2
is: I&5;) ( i’arr i , : IYYZ
I80 4014 : 1988
3 Dimensions
Dimension in millimtres
’ -.-.I
x
Maximum underhead fillet
3
zi
0 -.
32 37
37 42
.- -
-j-
-f
i--
Table 2 - Non-waferred threads
4
i I -
IS1364(Part1):1992
IS0 4014 : 1988
69
IS0 261, IS0 935-z
3mmcdc39mmm:ISO8981 dc3Smm:ISO3506
d<3mmandd>39mm: IS0 Es39
d > 39 mm: as aarecd
Acceptability
5 Designation
Exam;1!8 for ihe designation of a hexagon head bolt with thread M12, nominal length / = 80 mm and pwperty class 8.8:
IS0 225 IS 8535 : 1987 Bolts, screws, nuts and accessories - Identical
Terminology and nomenclature ( first revision )
IS0 261 IS 4218 ( Part 2 ) : 1976 IS0 metric screw threads: Part 2 Technically
Diameter pitch combinations ( first revision ) equivalent
IS0 888 IS 4206 : 1987 Dimensions for nominal lengths and thread Identical
lengths for bolts, screws and studs ( first revision )
IS0 898-l IS 1367 (Part 3 ) : 1991 Technical supply conditions for Identical
threaded steel fasteners : Part 3 Mechanical propertiesand
methods for bolts, screws and studs with full loadability
IS0 965-2 IS 4218 ( Part 6 ) : 1978 IS0 metric screw threads : Part 6 Technically
Limits of sizes for commercial bolts and nuts ( diameter range 1 equivalent
to 52 mm ) ( first revision )
IS0 3269 IS 1367 ( Part 17 ) : Technical supply conditions for threaded Technically
steel fasteners : Part 17 Acceptance criteria ( under preparation ) equivalent
IS0 3506 IS 1367 ( Part 14 ). : 1989 Technical supply conditions for Technically
threaded steel fasteners : Part 14 Stainless steel threaded equivalent
fasteners ( second revision )
IS0 4042 IS 1367 (Part 11 ) : Technical supply conditions for Technically
threaded steel fasteners : Part 11 Electroplated coatings on equiiralent
threaded steel fasteners ( under preparation )
IS0 4753 IS 1368 : 1987 Dimensions for ends of parts with externai IS0 Identical
metric threads ( third revision )
IS0 4759-l IS 1367 ( Part 2 ) : 1979 Technical supply conditions for Technically
threaded steel fasteners : Part 2 Product grades and tolerances equivalent
( second revision )
IS0 6157-1 IS 1367 ( Part 9/Set 1 ) : Technical supply conditions for Identical
threaded steal fasteners : Part 9 Surface discontinuities on
bolts, screws and studs, Section 1 General requirements ( wr&~e,
preparation )
IS0 6157-3 IS 1367 ( Part 9/&c 2 ) : Technical supply conditions for Identical
threaded steel fasteners : Part 9 Surface discontinuities on
bolts, screws and studs, Section 2 Special requirements ( under
prrpnralion )
IS0 8839 IS......Mechanical properties of fasteners-Bolts. screws, studs Identical
and nuts made of non-ferrous metals ( unda preparation )
IS0 8992 IS 1367 ( Part 1 ) : 1980 Technical supply conditions for Equivalent
threaded steel fasteners: Part 1 Introduction and general
information ( second revision: )
ALTERATION
111clause 5, the designation of hexagon head halt may be read as ‘Hexagon head bolts
IS 1364 ( Part 1 )--IS0 4014-M12x80,.-8‘8’ in place of ‘Hcxagan head bolt IS0 4014-
M12x80-8’8’.
Bureau of Indian Standards
BIS is a statutory institution established under the Bureau of Indian StandardsJAcr, 1986 to
promote harmonious developmc:lt of the activities of standardization, marking and quality
certification of goods and attending to connected matters in the country.
Copyright
BIS has the copyright of all its pab!ications. No part of these publications‘may hc rcproduccd
in any form without the prior permission i:t writing of BJS. This does not prccludc t!)c free IISC,
in the course of imple;;lenting the standnxi. of necessary details, such as symbols awl sizes. typ:
or grade designatioos. ISnqcirics rel:?ting to copyrighr be addressed 10 the Director
( Publications ), 1~1%
Indian Standards are rwiewcd periodically and revised, when necessary and alccntlltlents, if
any. are issued from tune to time. Users of Indian Standards should ascertain that they are in
possession of the la!cst amcndmcnts or edition. Comments on this Indian Standard may be
sent to BIS giving the following reference:
----.-.-.-. . .._..__..~___
Amend No. l>atc of Issue T‘cxc /wccted
-.-.___ -------
.- .^..._......- -- _._...-__
--... --___
Headquarters:
Manak Bhavan, 9 Ba!ladu! Ch::h i:af:~r Mug, New Delhi 110002
Telephones : 331 01 31, 331 I3 75