Documente Academic
Documente Profesional
Documente Cultură
Installation
Automatic Transfer Switching Equipment
NZ7 Series
ZHEJIANG CHINT ELECTRICS CO.,LTD
Add: No. 1, CHINT Road, CHINT Industrial Zone, North Baixiang,
Yueqing, Zhejiang Province, P.R.China 325603
Tel: +86-577-62877777
Fax: +86-577-62775769 62871811
E-mail: global-sales@chint.com
Website: w w w .chint.com
CHINT Electric All Rights Reserved Recycle Paper Printed Specifications and technical data are subject to change without notice.
Please contact us to confirm relevant information on ordering
Warning
This equipment should only be mounted by professionals. The manufacturer shall not be held responsible
for any failure to comply with the instruction given in this manual. The expression right of the instruction is owned by CHINT.
Catalog
B Preparations 2
C Storage 4
E Installation 8
Preparations
Test
1. Manual test
2. Power test
2 2
1 2 OFF QN QR
3 QN: ON QN QR 4 QR: ON QN QR
Manual test
Preparations
Power test
Operational details of the reference P8 ~ P15
3
Storage
,51ņ
.6ņ
,3111n
Pollution degree 3
Storage
41 61 81
21 :1
,51ņ
&SI
41 61 81 ჸ
21 :1
.6ņ &SI
OFF
5
The necessary tools
Hex key
Screw-driver
4 6 18 10
Standard accessories
Optional
7
Installation
Power bus-bar
1 Load bus-bar
Installation
Wiring
UN UR
UN N pole UR N pole
NN NR
Wiring terminal of zero line
Wiring terminal
of zero line
UN UR
9
Installation
Tripping signal
Tripping signal
Power signal
Power signal
On signal
On signal
Zero line
Zero line
Output is AC230V/0.5A
Feedback signal
DC24V/0.5A
Installation
3 4 5
CLACK!
21
Installation
1 2 3
4
5 9
6 10
7 11
12
8 13
19
14 18
15 17
16
22
Installation
1. Indication of automatic working mode; 15. Button for compulsorily turn off the normal power
2. Indication of manual working mode; Under the manual control mode, if this button is pressed, it can
3. Failure indication compulsorily switch to the normal power; if it is setting condition, this
When the breaker is disengaged due to the failure or short-circuit button is the “scroll up” button of setting programs;
of the switch, this lamp will be on; 16. Button for compulsorily turn off the alternative power
4. Display area of normal power voltage parameters Under the manual control mode, if this button is pressed, it can
It displays normal power voltage parameters and changeover compulsorily switch to the alternative power; if it is setting condition, this
delay time under the working condition, and setting items under button is the “scroll up” button of setting programs;
the setting condition; 17. Off button
5. Indication of the on or off of breaker on the normal power side Under the manual control mode, if either line of both power lines are
6. Indication of setting condition normal and this button is pressed, it will switch to the disengagement
7. Indication of the on or off of breaker on the alternative power side position; this button is the minus button for setting parameters when it is
8. Indication of the start of stop function; under setting condition;
9. Units of voltage, time, and frequency of the normal power; 18. Failure inquiry button
10. Phases A, B, and C; When the switch fails and malfunction lamp on the failure screen is
11. Units of voltage, time, and frequency of the alternative power; on, the detail malfunction code can be inquired if it is pressed; this
12. Display area of alternative power voltage parameters; button is the plus button if it is under the setting condition;
It displays alternative power voltage parameters and transfer 19. Setting button
delay time under the working condition, and setting items under When this button is pressed, it may enter into the parameter setting
the setting condition; menu of the controller.
13. Indication of the start signal of generator
14. Selection button of automatic/manual transfer
When it is regularly used, it can be used for selecting the automatic
or manual mode; it saves and exits the functions when it is under
the setting condition;
5
23
Installation
Press the Setting Button when the controller is working, LED will display
to increase and ▼ to decrease. 0s to 180s .
Set return delay time, press ▲ to increase
if the automatic/ manual button is pressed, it will exit the setting menu;
Set start delay time of generator, press ▲
increase and ▼ to decrease. 0s to 180s .
OFF
SET
S ET
SE T
SET
S ET
SET
SET
SET
SET
N ON
24
Installation
QN QR QN QR QN QR
UN is normal UN is normal UN is normal
UN fails UN fails UN fails
T1 can be adjusted from 0s to 180s T1 can be adjusted from 0s to 180s T3 can be adjusted from 0s to 180s
UN is QN QR
UN is QN QR
UR supplies
QN QR
UR supplies
QN QR UN is QN QR
disconnected
UN resumes to normal UN resumes to normal UR is put into use
T2 can be adjusted from 0s to 180s
QN QR
UR is UR supplies QN QR QN QR
disconnected UR supplies
UN is put into use UR fails UN resumes to normal
T1 can be adjusted from 0s to 180s T2 can be adjusted from 0s to 180s
QN QR UR is QN QR
UR is QN QR
UN supplies disconnected disconnected
UN is put into use
UN is put into use
QN QR QN QR
UN supplies UN supplies
UN is put into use
T4 can be adjusted from 0s to 180s
Generator shuts down
7 T1: Transfer delay can be adjusted from 0s to 180s T4: Delay time in shutting-down generator can be adjusted from 0s to 180s
Failure of UN , time before disconnecting QN QN: Operating breaker on the frequently used side
T2: Return delay time can be adjusted from 0s to 180s QR: Operating breaker on the stand-by side
Normal of UN , time before disconnecting QR UN : Normal power supply
T3: Delay time in starting generator can be adjusted from 0s to 180s UR : Alternative power supply
25
Installation
UN normal
To control center
UN
terminal of the
Internal contact
controller
QN on
QN tripped
To the remote port of the generator
UR
QR on
QR tripped
26
Installation
Wire connection
27
Installation
Phase barrier
28
Installation
1 Outline dimension
29
Installation
2 Installation dimension
2:
Installation
Controller Module
140
140
50
80
31