Documente Academic
Documente Profesional
Documente Cultură
1 Configuration Guide
Version 1 / Issue 1
Date July 28, 2009
www.alcatel-lucent.com
TABLE OF CONTENTS
1 Introduction............................................................................................................................. 3
2 Special Notes .......................................................................................................................... 3
3 Overview................................................................................................................................. 3
4 Configuration Guide ............................................................................................................... 4
5 Troubleshooting .................................................................................................................... 11
1. Introduction
This configuration guide describes how to configure Alcatel-Lucent OmniPCX Office
(OXO) to connect to AT&T’s Flexible Reach Service.
OXO must be equipped with VoIP board to configure SIP trunk. OXO was tested with
release R7.1 build 28.001.
This is a general description of OXO configuration for ATT SIP trunk purpose for more
details please refers to PublicSIPtrunking_ConfigurationGuide_OXO_ed1 document and
Expert documentation for R710.
2. Special Notes
T.38 Fax is supported with the following exception. Fax is not supported with Cisco
TDM gateways.
3. Overview
OXO was configured to support 8 SIP trunk channels, has 3 IP phones, 1 UA phone, 1
SG3 fax machine and 1 analog modem: Multitech MT9234ZBA-USB used for SG3 fax
and softphone Pimphony ver. 6.3. We have connected 1 POTS line to simulate rollover
when SIP trunk is down.
Customer Premises
IP Border
Element
Customer firewall
FAX OXO
4. Configuration Guide
OXO needs to be run on release 710.028.001 or higher to compliant with ATT SIP
service.
To check OXO software please go to:
Data Saving & Swapping > SW-Downloading
DID numbers should be assign to stations under: Numbering > Dialing Plan > Public
Dialing Plan
4.3. IP Configuration
By default system has the following IP configuration:
Main CPU: 192.168.92.246
VoIP Master: 192.168.92.248
Default GW: 192.168.92.246
And Hardware and Limits > LAN/IP configuration > Boards to change CPU and VoIP
master IPs:
By default system has enabled H.323 as VoIP protocol and no channels are assigned to
VoIP trunk. VoIP protocol must be switched to SIP and the number of channels must be
increased under:
Voice Over IP > VoIP: Parameters > General
Additionally the noteworthy label SimullpAlt must be changed to 01, in order to do this
please go to:
System Miscellaneous > Memory Read/Write > Other Labels
Next the List Index needs to be created for new VoIP Trunk Group under:
Numbering > Automatic Routing Selection > Trunk Group List
- create a list index for trunk group
Now the ARS route must be created to send all number to VoIP trunk group list:
Numbering > Automatic Routing Selection > Automatic Routing: Prefixes
- add a line that routes prefix 1 for example to the VoIP trunk with following
settings:
Activation – YES
Network – Pub
Prefix – 1
Ranges – 0-9
Substitute – leave blank
TrGpList – enter the trunk group list index
Called(ISVPN/H450) – het
Destination – SIP Gateway
IP Type – Static
IP Address – in test scenario: 207.242.225.200
Gateway Alive Protocol – SIP Option
Gateway Alive Timeout – enter desired time period in seconds
Gateway Bandwidth – choose right value depends on number of VoIP channels and
carrier bandwidth
In above example you can see that for prefix 1 main line and subline were added to
rollover calls to another ATT SIP gateway IP: 207.242.225.201 and if both IP
gateways down calls are sent to POTS lines. SIP Option is used for a keep alive
mechanism. Note that AT&T customer care will provide the customer with
the 2 AT&T SIP endpoints during provisioning.
To create Gateway Parameters in OMC go to:
Numbering > Automatic Routing Selection > Gateway Parameters
- add new index with following settings:
RFC 3325 – Yes
Remote SIP port – 5060
Index of SIP Numbers Format – 1
DNS – Disabled
To create trunk access prefix for ARS in OMC main trunk group prefix needs to be
modified under:
Numbering > Dialing Plans > Internal Dialing > Main Trunk Group
- modify with following setting:
Start – 9
End – 9
Base – ARS
NMT – Drop
Priv – No
Accept new setting by with Modify key.
5. Troubleshooting
If you need a technical assistance please call ALU Technical Support line to open a
case, the phone number is +1 (877) 729-7299.