Documente Academic
Documente Profesional
Documente Cultură
SPECIFICATIONS
ENGINE BRAKES
IVECO Tector F4A E25 Full air-brake system with two independent circuits
Type: Turbocharged and intercooled 24-valve four-stroke diesel with 377 x 45 mm ventilated front/rear disc brakes with floating
high-pressure common-rail electronic injection calipers (asbestos free)
Number of cylinders: 6 ABS: Three-channel system
Displacement: 5.88 litres Spring-actuated park brake acting on rear wheels
Bore x stroke: 102 x 120 mm Exhaust brake (three mode)
Compression ratio: 17:1 Air dryer
Maximum output: 185 kW (251 hp) @ 2,500 rpm 360 cc air compressor (water cooled)
Maximum torque: 850 Nm (627 lb/ft) @ 1,250-2,100 rpm ESP & ASR
Governed speed: 2,700 rpm
RAC hp rating: 38.7 STEERING
Oil capacity: 11.6 litres Type: Integral power-assisted circulating ball with gear-driven pump
SCR - Selective Catalytic Reduction and integral reservoir
Emissions standard: EURO 5 Ratio: 20.4
Tilt-adjustable 470 mm diameter steering wheel
TRANSMISSION Angular 17° and Vertical 50 mm
Eaton ZF 6S800 six-speed automated and manual Synchromesh
transmission cable gear shift, H over H shift pattern FUEL SYSTEM
1st 6.58:1 Nominal tank capacity: 280 litres
2nd 3.60:1 Fuel prefilter with water separator fitted to chassis
3rd 2.12:1 Ad Blue Tank: 25 litres
4th 1.39:1
ELECTRICAL
5th 1.00:1
6th 0.78:1 Type: 24V negative to earth
Reverse 6.08:1 24V-12V converter in cab
Alternator capacity: 28V, 90 amp
CLUTCH Starter: 24V, 4.0 kW
Type: Single-plate asbestos-free push type with air over hydraulic Battery: 2 x 12V 110 Ah
assistance Automatic battery isolation switch
Diameter: 395 mm
WHEELS AND TYRES
Lining area: 582 cm²
Wheels: One-piece steel disc rims
FRONT AXLE Stud and pattern: M22, 8 x 275 mm PCD
Iveco 5860 Disc size: 19.5” x 6.75”
Type: I-beam with oil-filled hubs Tyres: 265/70R19.5 tubeless radial
Capacity: 4,480 kg Tyre minimum rating: 136/134M
Spare located on left-hand side
REAR AXLE
Meritor MS10-144 CAB
Type: Single-reduction fully-floating banjo type Type: Forward-control (MLC) Day cabin
Differential lock standard on manual transmission, Construction: Pressed two-side zinc-coated steel on selected outer
option with automated panels with Electr-cataphoretic corrosion protection. PP front panels
Capacity: 8,480 kg and fenders
Ratio: 3.90:1 Option 1:
(MLL) Sleeper cabin
FRONT SUSPENSION ADR-compliant, fully-finished sleeper cab with bunk, curtains, reading
Type: Parabolic lamp, roof hatch and two internal and one external lockers
Parabolic springs with dual-action hydraulic shock absorbers and Bunk dimensions: 1900 x 605 x 95mm
stabiliser bar fitted Cab colour bumper
REAR SUSPENSION Four-point cab suspension
Front: Two coil springs, shock absorbers and torsion bar
Type: Air bag
Rear: Two units with coils springs
Two bellows, rear air bag suspension with dual shock absorbers
Hydraulic cab tilt to 60º
ECAS Electronically Controlled Air Suspension including dual-rear
levelling valves
Remote-control operation complete with memory function
CHASSIS
Type: bolted and riveted parallel channel
Size: 253.4 x 70 x 6.7 mm (253.4 x 70 x 7.7mm on 5.67m Wheelbase)
Width: 853 mm
Yield strength: 490 MPa
Heavy-duty front tow hook
ML120E25P
SPECIFICATIONS
AC
CF
10 U
1362 WB AF W
L
The data contained in this publication are purely indicative and is not binding.