Documente Academic
Documente Profesional
Documente Cultură
FZ6-S
FZ6-SS
5VX-28199-EB
U5VXEBE0.book Page 1 Monday, August 8, 2005 10:32 AM
EAU26942
U5VXEBE0.book Page 1 Monday, August 8, 2005 10:32 AM
INTRODUCTION
EAU10100
Failure to follow WARNING instructions could result in severe injury or death to the
WARNING motorcycle operator, a bystander, or a person inspecting or repairing the motor-
cycle.
NOTE:
● This manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle
is subsequently sold.
● Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most
current product information available at the time of printing, there may be minor discrepancies between your motorcycle
and this manual. If you have any questions concerning this manual, please consult your Yamaha dealer.
EWA10030
WARNING
PLEASE READ THIS MANUAL CAREFULLY AND COMPLETELY BEFORE OPERATING THIS MOTORCYCLE.
*Product and specifications are subject to change without notice.
U5VXEBE0.book Page 2 Monday, August 8, 2005 10:32 AM
EAU10200
FZ6-S/FZ6-SS
OWNER’S MANUAL
©2005 by Yamaha Motor Co., Ltd.
1st edition, July 2005
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Co., Ltd.
is expressly prohibited.
Printed in Japan.
U5VXEBE0.book Page 1 Monday, August 8, 2005 10:32 AM
TABLE OF CONTENTS
SAFETY INFORMATION ..................1-1 PRE-OPERATION CHECKS ............. 4-1 Adjusting the rear brake light
Pre-operation check list .................. 4-2 switch ....................................... 6-18
DESCRIPTION ..................................2-1 Checking the front and rear
Left view ..........................................2-1 OPERATION AND IMPORTANT brake pads ................................ 6-18
Right view ........................................2-2 RIDING POINTS................................. 5-1 Checking the brake fluid level ...... 6-19
Controls and instruments.................2-3 Starting the engine ......................... 5-1 Changing the brake fluid .............. 6-20
Shifting ........................................... 5-2 Drive chain slack .......................... 6-20
INSTRUMENT AND CONTROL Tips for reducing fuel Cleaning and lubricating the
FUNCTIONS .......................................3-1 consumption ............................... 5-3 drive chain ................................ 6-22
Immobilizer system .........................3-1 Engine break-in .............................. 5-3 Checking and lubricating the
Main switch/steering lock ................3-2 Parking ........................................... 5-4 cables ....................................... 6-22
Indicator and warning lights ............3-3 Checking and lubricating the
LCD tachometer .............................3-5 PERIODIC MAINTENANCE AND throttle grip and cable ............... 6-23
Multi-function display ......................3-5 MINOR REPAIR ................................. 6-1 Checking and lubricating the
Anti-theft alarm (optional) ...............3-8 Owner’s tool kit ............................... 6-1 brake and shift pedals .............. 6-23
Handlebar switches ........................3-8 Periodic maintenance and Checking and lubricating the
Clutch lever ...................................3-10 lubrication chart .......................... 6-2 brake and clutch levers ............ 6-24
Shift pedal .....................................3-10 Removing and installing panels ..... 6-5 Checking and lubricating the
Brake lever ...................................3-10 Checking the spark plugs ............... 6-6 centerstand and sidestand ....... 6-24
Brake pedal ..................................3-11 Engine oil and oil filter cartridge ..... 6-7 Lubricating the swingarm
Fuel tank cap ................................3-11 Coolant ......................................... 6-10 pivots ........................................ 6-25
Fuel ...............................................3-12 Replacing the air filter element ..... 6-12 Checking the front fork ................. 6-25
Fuel tank breather hose ................3-13 Adjusting the engine idling Checking the steering .................. 6-26
Catalytic converter ........................3-13 speed ........................................ 6-13 Checking the wheel bearings ....... 6-26
Seat ..............................................3-13 Checking the throttle cable Battery ......................................... 6-27
Storage compartment ...................3-14 free play .................................... 6-14 Replacing the fuses ..................... 6-28
Adjusting the shock absorber Valve clearance ............................ 6-14 Replacing the headlight bulb ....... 6-29
assembly ...................................3-15 Tires ............................................. 6-14 Replacing the tail/brake light
Sidestand ......................................3-16 Cast wheels .................................. 6-17 bulb ........................................... 6-30
Ignition circuit cut-off system ........3-16 Adjusting the clutch lever Replacing a turn signal light
free play .................................... 6-17 bulb ........................................... 6-31
U5VXEBE0.book Page 2 Monday, August 8, 2005 10:32 AM
TABLE OF CONTENTS
Replacing the license plate light
bulb ...........................................6-31
Replacing an auxiliary light bulb ...6-32
Front wheel ...................................6-33
Rear wheel ...................................6-34
Troubleshooting ............................6-36
Troubleshooting charts .................6-37
SPECIFICATIONS .............................8-1
CONSUMER INFORMATION.............9-1
Identification numbers ....................9-1
U5VXEBE0.book Page 1 Monday, August 8, 2005 10:32 AM
SAFETY INFORMATION
EAU10281
AND/OR WHEN MADE NECES- • Ride where other motorists can
SARY BY MECHANICAL CONDI- see you. Avoid riding in another
MOTORCYCLES ARE SINGLE TIONS. motorist’s blind spot.
1 TRACK VEHICLES. THEIR SAFE USE ● Many accidents involve inexperi-
AND OPERATION ARE DEPENDENT Safe riding enced operators. In fact, many op-
UPON THE USE OF PROPER RIDING ● Always make pre-operation erators who have been involved in
TECHNIQUES AS WELL AS THE EX- checks. Careful checks may help accidents do not even have a cur-
PERTISE OF THE OPERATOR. EV- prevent an accident. rent motorcycle license.
ERY OPERATOR SHOULD KNOW ● This motorcycle is designed to car- • Make sure that you are qualified
THE FOLLOWING REQUIREMENTS ry the operator and a passenger. and that you only lend your
BEFORE RIDING THIS MOTOR- ● The failure of motorists to detect motorcycle to other qualified op-
CYCLE. and recognize motorcycles in traf- erators.
HE OR SHE SHOULD: fic is the predominating cause of • Know your skills and limits.
● OBTAIN THOROUGH INSTRUC- automobile/motorcycle accidents. Staying within your limits may
TIONS FROM A COMPETENT Many accidents have been caused help you to avoid an accident.
SOURCE ON ALL ASPECTS OF by an automobile driver who did • We recommend that you prac-
MOTORCYCLE OPERATION. not see the motorcycle. Making tice riding your motorcycle
● OBSERVE THE WARNINGS AND yourself conspicuous appears to where there is no traffic until you
MAINTENANCE REQUIRE- be very effective in reducing the have become thoroughly famil-
MENTS IN THE OWNER’S MAN- chance of this type of accident. iar with the motorcycle and all of
UAL. Therefore: its controls.
● OBTAIN QUALIFIED TRAINING • Wear a brightly colored jacket. ● Many accidents have been caused
IN SAFE AND PROPER RIDING • Use extra caution when you are by error of the motorcycle opera-
TECHNIQUES. approaching and passing tor. A typical error made by the op-
● OBTAIN PROFESSIONAL TECH- through intersections, since in- erator is veering wide on a turn
NICAL SERVICE AS INDICATED tersections are the most likely
BY THE OWNER’S MANUAL places for motorcycle accidents
to occur.
1-1
U5VXEBE0.book Page 2 Monday, August 8, 2005 10:32 AM
SAFETY INFORMATION
due to EXCESSIVE SPEED or un- ● This motorcycle is designed for on- cause burns. Always wear protec-
dercornering (insufficient lean an- road use only. It is not suitable for tive clothing that covers your legs,
gle for the speed). off-road use. ankles, and feet.
• Always obey the speed limit and ● A passenger should also observe 1
never travel faster than warrant- Protective apparel the above precautions.
ed by road and traffic conditions. The majority of fatalities from motor-
• Always signal before turning or cycle accidents are the result of head Modifications
changing lanes. Make sure that injuries. The use of a safety helmet is Modifications made to this motorcycle
other motorists can see you. the single most critical factor in the pre- not approved by Yamaha, or the re-
● The posture of the operator and vention or reduction of head injuries. moval of original equipment, may ren-
passenger is important for proper ● Always wear an approved helmet. der the motorcycle unsafe for use and
control. ● Wear a face shield or goggles. may cause severe personal injury.
• The operator should keep both Wind in your unprotected eyes Modifications may also make your
hands on the handlebar and could contribute to an impairment motorcycle illegal to use.
both feet on the operator foot- of vision that could delay seeing a
rests during operation to main- hazard. Loading and accessories
tain control of the motorcycle. ● The use of a jacket, heavy boots, Adding accessories or cargo to your
• The passenger should always trousers, gloves, etc., is effective in motorcycle can adversely affect stabili-
hold onto the operator, the seat preventing or reducing abrasions ty and handling if the weight distribution
strap or grab bar, if equipped, or lacerations. of the motorcycle is changed. To avoid
with both hands and keep both ● Never wear loose-fitting clothes, the possibility of an accident, use ex-
feet on the passenger footrests. otherwise they could catch on the treme caution when adding cargo or
• Never carry a passenger unless control levers, footrests, or wheels accessories to your motorcycle. Use
he or she can firmly place both and cause injury or an accident. extra care when riding a motorcycle
feet on the passenger footrests. ● Never touch the engine or exhaust that has added cargo or accessories.
● Never ride under the influence of system during or after operation. Here are some general guidelines to
alcohol or other drugs. They become very hot and can follow if loading cargo or adding acces-
sories to your motorcycle:
1-2
U5VXEBE0.book Page 3 Monday, August 8, 2005 10:32 AM
SAFETY INFORMATION
Loading bags, duffel bags, or tents, can limit suspension travel, steering
The total weight of the operator, pas- create unstable handling or a slow travel or control operation, or ob-
senger, accessories and cargo must steering response. scure lights or reflectors.
1 not exceed the maximum load limit. Accessories • Accessories fitted to the handle-
Genuine Yamaha accessories have bar or the front fork area can
Maximum load: been specifically designed for use on create instability due to improper
190 kg (419 lb) this motorcycle. Since Yamaha cannot weight distribution or aerody-
test all other accessories that may be namic changes. If accessories
When loading within this weight limit,
available, you must personally be re- are added to the handlebar or
keep the following in mind:
sponsible for the proper selection, in- front fork area, they must be as
● Cargo and accessory weight
stallation and use of non-Yamaha lightweight as possible and
should be kept as low and close to
accessories. Use extreme caution should be kept to a minimum.
the motorcycle as possible. Make
when selecting and installing any ac- • Bulky or large accessories may
sure to distribute the weight as
cessories. seriously affect the stability of
evenly as possible on both sides of
Keep the following guidelines in mind, the motorcycle due to aerody-
the motorcycle to minimize imbal-
as well as those provided under “Load- namic effects. Wind may at-
ance or instability.
ing” when mounting accessories. tempt to lift the motorcycle, or
● Shifting weights can create a sud-
● Never install accessories or carry the motorcycle may become un-
den imbalance. Make sure that ac-
cargo that would impair the perfor- stable in cross winds. These ac-
cessories and cargo are securely
mance of your motorcycle. Care- cessories may also cause
attached to the motorcycle before
fully inspect the accessory before instability when passing or being
riding. Check accessory mounts
using it to make sure that it does passed by large vehicles.
and cargo restraints frequently.
not in any way reduce ground • Certain accessories can dis-
● Never attach any large or heavy
clearance or cornering clearance, place the operator from his or
items to the handlebar, front fork,
her normal riding position. This
or front fender. These items, in-
improper position limits the free-
cluding such cargo as sleeping
dom of movement of the opera-
1-3
U5VXEBE0.book Page 4 Monday, August 8, 2005 10:32 AM
SAFETY INFORMATION
tor and may limit control ability, ● Always turn the engine off before or clothing, immediately wash the
therefore, such accessories are leaving the motorcycle unattended affected area with soap and water
not recommended. and remove the key from the main and change your clothes.
● Use caution when adding electri- switch. When parking the motor- 1
cal accessories. If electrical acces- cycle, note the following:
sories exceed the capacity of the • The engine and exhaust system
motorcycle’s electrical system, an may be hot, therefore, park the
electric failure could result, which motorcycle in a place where pe-
could cause a dangerous loss of destrians or children are not like-
lights or engine power. ly to touch these hot areas.
• Do not park the motorcycle on a
Gasoline and exhaust gas slope or soft ground, otherwise it
● GASOLINE IS HIGHLY FLAMMA- may fall over.
BLE: • Do not park the motorcycle near
• Always turn the engine off when a flammable source, (e.g., a ker-
refueling. osene heater, or near an open
• Take care not to spill any gaso- flame), otherwise it could catch
line on the engine or exhaust fire.
system when refueling. ● When transporting the motorcycle
• Never refuel while smoking or in in another vehicle, make sure that
the vicinity of an open flame. it is kept upright. If the motorcycle
● Never start the engine or let it run should lean over, gasoline may
for any length of time in a closed leak out of the fuel tank.
area. The exhaust fumes are poi- ● If you should swallow any gaso-
sonous and may cause loss of line, inhale a lot of gasoline vapor,
consciousness and death within a or allow gasoline to get into your
short time. Always operate your eyes, see your doctor immediately.
motorcycle in an area that has ad- If any gasoline spills on your skin
equate ventilation.
1-4
U5VXEBE0.book Page 1 Monday, August 8, 2005 10:32 AM
DESCRIPTION
EAU10410
Left view
1. Main fuse (page 6-28) 9. Engine oil filter cartridge (page 6-7)
2. Battery (page 6-27)
3. Air filter element (page 6-12)
4. Idle adjusting screw (page 6-13)
5. Shock absorber assembly spring preload adjusting ring (page 3-15)
6. Owner’s tool kit (page 6-1)
7. Shift pedal (page 3-10)
8. Engine oil drain bolt (page 6-7)
2-1
U5VXEBE0.book Page 2 Monday, August 8, 2005 10:32 AM
DESCRIPTION
EAU10420
Right view
2-2
U5VXEBE0.book Page 3 Monday, August 8, 2005 10:32 AM
DESCRIPTION
EAU10430
2-3
U5VXEBE0.book Page 1 Monday, August 8, 2005 10:32 AM
3-1
U5VXEBE0.book Page 2 Monday, August 8, 2005 10:32 AM
3-2
U5VXEBE0.book Page 3 Monday, August 8, 2005 10:32 AM
1. Push. CAUTION:
2. Turn. 1. Oil level warning light “ ”
Do not use the parking position for 2. Engine trouble warning light “ ”
Push the key in, and then turn it to an extended length of time, other- 3. Neutral indicator light “ ”
“OFF” while still pushing it. wise the battery may discharge. 4. High beam indicator light “ ”
EWA10060 5. Immobilizer system indicator light “ ”
WARNING 6. Turn signal indicator lights “ ” and “ ”
Never turn the key to “OFF” or
EAU11030
“LOCK” while the vehicle is moving, Turn signal indicator lights “ ” and
otherwise the electrical systems will “ ”
be switched off, which may result in The corresponding indicator light flash-
loss of control or an accident. Make es when the turn signal switch is
sure that the vehicle is stopped be- pushed to the left or right.
fore turning the key to “OFF” or
“LOCK”. EAU11060
Neutral indicator light “ ”
This indicator light comes on when the
transmission is in the neutral position.
3-3
U5VXEBE0.book Page 4 Monday, August 8, 2005 10:32 AM
3-4
U5VXEBE0.book Page 5 Monday, August 8, 2005 10:32 AM
1. LCD tachometer
2. Tachometer red zone
3-5
U5VXEBE0.book Page 6 Monday, August 8, 2005 10:32 AM
CAUTION:
If the display indicates an error
code, the vehicle should be checked
as soon as possible in order to avoid
engine damage.
3-8
U5VXEBE0.book Page 9 Monday, August 8, 2005 10:32 AM
3-9
U5VXEBE0.book Page 10 Monday, August 8, 2005 10:32 AM
The clutch lever is located at the left The shift pedal is located on the left
handlebar grip. To disengage the side of the engine and is used in com-
clutch, pull the lever toward the handle- bination with the clutch lever when
1. Brake lever
bar grip. To engage the clutch, release shifting the gears of the 6-speed con- 2. Brake lever position adjusting dial
the lever. The lever should be pulled stant-mesh transmission equipped on 3. “ ” mark
rapidly and released slowly for smooth this motorcycle. 4. Distance between brake lever and handlebar
clutch operation. grip
The clutch lever is equipped with a
The brake lever is equipped with a po-
clutch switch, which is part of the igni-
sition adjusting dial. To adjust the dis-
tion circuit cut-off system. (See page
tance between the brake lever and the
3-16.)
handlebar grip, turn the adjusting dial
while holding the lever pushed away
from the handlebar grip. Make sure that
the appropriate setting on the adjusting
dial is aligned with the “ ” mark on the
brake lever.
3-10
U5VXEBE0.book Page 11 Monday, August 8, 2005 10:32 AM
WARNING
Make sure that the fuel tank cap is 3
properly closed before riding.
3-11
U5VXEBE0.book Page 12 Monday, August 8, 2005 10:32 AM
EAU13320
3
Recommended fuel:
1. Fuel tank filler tube REGULAR UNLEADED GASOLINE
ONLY
2. Fuel level
Fuel tank capacity:
Make sure that there is sufficient fuel in 19.4 L (5.13 US gal) (4.27 Imp.gal)
Fuel reserve amount:
the tank. When refueling, be sure to in- 3.6 L (0.95 US gal) (0.79 Imp.gal)
sert the pump nozzle into the fuel tank
filler hole and to fill the tank to the bot- ECA11400
3-13
U5VXEBE0.book Page 14 Monday, August 8, 2005 10:32 AM
3
1. Projection
2. Seat holder
1. U-LOCK bar (optional)
2. Push the rear of the seat down to 2. Yamaha U-LOCK (optional)
lock it in place. 3. Strap
3. Remove the key.
This storage compartment is designed
NOTE: to hold a genuine Yamaha U-LOCK.
Make sure that the seat is properly se- (Other locks may not fit.) When placing
cured before riding. a U-LOCK in the storage compartment,
securely fasten it with the straps. When
the U-LOCK is not in the storage com-
partment, be sure to secure the straps
to prevent losing them.
EWA10961
WARNING
● Do not exceed the load limit of 3
kg (7 lb) for the storage com-
partment.
3-14
U5VXEBE0.book Page 15 Monday, August 8, 2005 10:32 AM
Sidestand pair it if it does not function proper- Ignition circuit cut-off system
The sidestand is located on the left side ly. The ignition circuit cut-off system (com-
of the frame. Raise the sidestand or prising the sidestand switch, clutch
lower it with your foot while holding the switch and neutral switch) has the fol-
vehicle upright. lowing functions.
● It prevents starting when the trans-
NOTE:
mission is in gear and the side-
The built-in sidestand switch is part of
3 stand is up, but the clutch lever is
the ignition circuit cut-off system, which
not pulled.
cuts the ignition in certain situations.
● It prevents starting when the trans-
(See further down for an explanation of
mission is in gear and the clutch le-
the ignition circuit cut-off system.)
ver is pulled, but the sidestand is
EWA10240
still down.
WARNING ● It cuts the running engine when the
The vehicle must not be ridden with transmission is in gear and the sid-
the sidestand down, or if the side- estand is moved down.
stand cannot be properly moved up Periodically check the operation of the
(or does not stay up), otherwise the ignition circuit cut-off system according
sidestand could contact the ground to the following procedure.
EWA10260
and distract the operator, resulting
in a possible loss of control. WARNING
Yamaha’s ignition circuit cut-off ● The vehicle must be placed on
system has been designed to assist the centerstand during this in-
the operator in fulfilling the respon- spection.
sibility of raising the sidestand be- ● If a malfunction is noted, have a
fore starting off. Therefore, check Yamaha dealer check the sys-
this system regularly as described tem before riding.
3-16
U5VXEBE0.book Page 17 Monday, August 8, 2005 10:32 AM
3-17
U5VXEBE0.book Page 1 Monday, August 8, 2005 10:32 AM
PRE-OPERATION CHECKS
EAU15591
The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly,
even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss
of tire air pressure could have serious consequences. Therefore, it is very important, in addition to a thorough visual inspec-
tion, to check the following points before each ride.
NOTE:
Pre-operation checks should be made each time the vehicle is used. Such an inspection can be accomplished in a very short
time; and the added safety it assures is more than worth the time involved.
EWA11150
4
WARNING
If any item in the Pre-operation check list is not working properly, have it inspected and repaired before operating
the vehicle.
4-1
U5VXEBE0.book Page 2 Monday, August 8, 2005 10:32 AM
PRE-OPERATION CHECKS
EAU15603
4-2
U5VXEBE0.book Page 3 Monday, August 8, 2005 10:32 AM
PRE-OPERATION CHECKS
ITEM CHECKS PAGE
4-3
U5VXEBE0.book Page 1 Monday, August 8, 2005 10:32 AM
5-2
U5VXEBE0.book Page 3 Monday, August 8, 2005 10:32 AM
5-3
U5VXEBE0.book Page 4 Monday, August 8, 2005 10:32 AM
Parking
When parking, stop the engine, and
then remove the key from the main
switch.
EWA10310
WARNING
● Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them.
● Do not park on a slope or on soft
5 ground, otherwise the vehicle
may overturn.
ECA10380
CAUTION:
Never park in an area where there
are fire hazards such as grass or
other flammable materials.
5-4
U5VXEBE0.book Page 1 Monday, August 8, 2005 10:32 AM
6-1
U5VXEBE0.book Page 2 Monday, August 8, 2005 10:32 AM
6-2
U5VXEBE0.book Page 3 Monday, August 8, 2005 10:32 AM
15 * Chassis fasteners
• Make sure that all nuts, bolts and screws are properly
√ √ √ √ √
6
tightened.
• Check operation.
16 Sidestand, centerstand √ √ √ √ √
• Lubricate.
17 * Sidestand switch • Check operation. √ √ √ √ √ √
18 * Front fork • Check operation and for oil leakage. √ √ √ √
Shock absorber assem-
19 * • Check operation and shock absorber for oil leakage. √ √ √ √
bly
20 * Fuel injection • Adjust engine idling speed and synchronization. √ √ √ √ √ √
• Change.
21 Engine oil √ √ √ √ √ √
• Check oil level and vehicle for oil leakage.
Engine oil filter car-
22 • Replace. √ √ √
tridge
6-3
U5VXEBE0.book Page 4 Monday, August 8, 2005 10:32 AM
EAU18670
NOTE:
● The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
● Hydraulic brake service
• Regularly check and, if necessary, correct the brake fluid level.
• Every two years replace the internal components of the brake master cylinders and calipers, and change the brake
fluid.
• Replace the brake hoses every four years and if cracked or damaged.
6-4
U5VXEBE0.book Page 5 Monday, August 8, 2005 10:32 AM
1. Panel C 1. Panel A
2. Bolt
EAU32863 3. Quick fastener screw
Panels A and B
6-5
U5VXEBE0.book Page 6 Monday, August 8, 2005 10:32 AM
6-6
U5VXEBE0.book Page 7 Monday, August 8, 2005 10:32 AM
6-7
U5VXEBE0.book Page 8 Monday, August 8, 2005 10:32 AM
6-8
U5VXEBE0.book Page 9 Monday, August 8, 2005 10:32 AM
ECA11620
CAUTION:
1. Torque wrench
● In order to prevent clutch slip-
Tightening torque: page (since the engine oil also
Oil filter cartridge: lubricates the clutch), do not
17 Nm (1.7 m·kgf, 12 ft·lbf) mix any chemical additives. Do
not use oils with a diesel speci-
7. Install the engine oil drain bolt, and fication of “CD” or oils of a high- 6
then tighten it to the specified er quality than specified. In
1. O-ring torque. addition, do not use oils labeled
NOTE: NOTE: “ENERGY CONSERVING II” or
Make sure that the O-ring is properly Check the washer for damage and re- higher.
place it if necessary. ● Make sure that no foreign mate-
seated.
rial enters the crankcase.
6. Install the new oil filter cartridge
Tightening torque: 9. Start the engine, and then let it idle
with an oil filter wrench, and then
Engine oil drain bolt: for several minutes while checking
tighten it to the specified torque 43 Nm (4.3 m·kgf, 31 ft·lbf) it for oil leakage. If oil is leaking, im-
with a torque wrench.
mediately turn the engine off and
8. Add the specified amount of the
check for the cause.
recommended engine oil, and then
install and tighten the oil filler cap.
6-9
U5VXEBE0.book Page 10 Monday, August 8, 2005 10:32 AM
check the oil level and correct it if NOTE: 3. If the coolant is at or below the
necessary. ● The coolant level must be checked minimum level mark, remove the
6 on a cold engine since the level seat. (See page 3-13.)
varies with engine temperature. 4. Remove the fuel tank bolts, and
● Make sure that the vehicle is posi- then lift the fuel tank away from the
tioned straight up when checking coolant reservoir cap. (See page
the coolant level. A slight tilt to the 6-12.)
side can result in a false reading. 5. Open the coolant reservoir cap.
2. Check the coolant level in the cool-
ant reservoir.
NOTE:
The coolant should be between the
minimum and maximum level marks.
6-10
U5VXEBE0.book Page 11 Monday, August 8, 2005 10:32 AM
6-12
U5VXEBE0.book Page 13 Monday, August 8, 2005 10:32 AM
6-13
U5VXEBE0.book Page 14 Monday, August 8, 2005 10:32 AM
WARNING
1. Throttle cable free play
● The tire air pressure must be
The throttle cable free play should mea- checked and adjusted on cold
6 sure 3.0–5.0 mm (0.12–0.20 in) at the tires (i.e., when the temperature
throttle grip. Periodically check the of the tires equals the ambient
throttle cable free play and, if neces- temperature).
sary, have a Yamaha dealer adjust it. ● The tire air pressure must be ad-
justed in accordance with the
riding speed and with the total
weight of rider, passenger, car-
go, and accessories approved
for this model.
6-14
U5VXEBE0.book Page 15 Monday, August 8, 2005 10:32 AM
6-15
U5VXEBE0.book Page 16 Monday, August 8, 2005 10:32 AM
6-16
U5VXEBE0.book Page 17 Monday, August 8, 2005 10:32 AM
visable before doing any high- Cast wheels Adjusting the clutch lever free
speed riding to ride conserva- To maximize the performance, durabil- play
tively for approximately 100 km ity, and safe operation of your vehicle,
(60 mi) after installing a new tire. note the following points regarding the
● The tires must be warmed up specified wheels.
before a high-speed run. ● The wheel rims should be checked
● Always adjust the tire air pres- for cracks, bends or warpage be-
sure according to the operating fore each ride. If any damage is
conditions. found, have a Yamaha dealer re-
place the wheel. Do not attempt
even the smallest repair to the
wheel. A deformed or cracked
1. Clutch lever free play adjusting bolt
wheel must be replaced. 2. Clutch lever free play
● The wheel should be balanced
whenever either the tire or wheel The clutch lever free play should mea- 6
has been changed or replaced. An sure 10.0–15.0 mm (0.39–0.59 in) as
unbalanced wheel can result in shown. Periodically check the clutch le-
poor performance, adverse han- ver free play and, if necessary, adjust it
dling characteristics, and a short- as follows.
ened tire life. To increase the clutch lever free play,
● Ride at moderate speeds after turn the adjusting bolt in direction (a).
changing a tire since the tire sur- To decrease the clutch lever free play,
face must first be “broken in” for it turn the adjusting bolt in direction (b).
to develop its optimal characteris-
tics.
6-17
U5VXEBE0.book Page 18 Monday, August 8, 2005 10:32 AM
EAU22420
Front brake pads
6-18
U5VXEBE0.book Page 19 Monday, August 8, 2005 10:32 AM
ter the brake fluid reservoir when Changing the brake fluid Drive chain slack
refilling. Water will significantly Have a Yamaha dealer change the The drive chain slack should be
lower the boiling point of the fluid brake fluid at the intervals specified in checked before each ride and adjusted
and may result in vapor lock. the NOTE after the periodic mainte- if necessary.
● Brake fluid may deteriorate paint- nance and lubrication chart. In addition,
ed surfaces or plastic parts. Al- have the oil seals of the master cylin- EAU22791
To check the drive chain slack
ways clean up spilled fluid ders and calipers as well as the brake
1. Place the motorcycle on the cen-
immediately. hoses replaced at the intervals listed
terstand.
● As the brake pads wear, it is nor- below or whenever they are damaged
2. Shift the transmission into the neu-
mal for the brake fluid level to grad- or leaking.
tral position.
ually go down. However, if the ● Oil seals: Replace every two
3. Spin the rear wheel several times
brake fluid level goes down sud- years.
to locate the tightest portion of the
denly, have a Yamaha dealer ● Brake hoses: Replace every four
drive chain.
check the cause. years.
4. Measure the drive chain slack as
6
shown.
6-20
U5VXEBE0.book Page 21 Monday, August 8, 2005 10:32 AM
EAU34361
To adjust the drive chain slack
1. Loosen the axle nut, then loosen
the locknut at each end of the
swingarm. 1. Axle nut
2. To tighten the drive chain, turn the 2. Drive chain slack adjusting nut
3. Locknut
adjusting nut at each end of the
4. Alignment marks
swingarm in direction (a). To loos-
en the drive chain, turn the adjust- ECA10570
6-21
U5VXEBE0.book Page 22 Monday, August 8, 2005 10:32 AM
6-22
U5VXEBE0.book Page 23 Monday, August 8, 2005 10:32 AM
Checking and lubricating the Checking and lubricating the Recommended lubricant:
Lithium-soap-based grease (all-pur-
throttle grip and cable brake and shift pedals pose grease)
The operation of the throttle grip should
be checked before each ride. In addi-
tion, the cable should be lubricated at
the intervals specified in the periodic
maintenance chart.
6-23
U5VXEBE0.book Page 24 Monday, August 8, 2005 10:32 AM
Checking and lubricating the Recommended lubricant: Checking and lubricating the
Lithium-soap-based grease (all-pur-
brake and clutch levers pose grease) centerstand and sidestand
Brake lever
WARNING
If the centerstand or sidestand does
not move up and down smoothly,
have a Yamaha dealer check or re-
pair it.
The operation of the brake and clutch
levers should be checked before each Recommended lubricant:
Lithium-soap-based grease (all-pur-
ride, and the lever pivots should be lu- pose grease)
bricated if necessary.
6-24
U5VXEBE0.book Page 25 Monday, August 8, 2005 10:32 AM
WARNING
Securely support the vehicle so that ECA10590
6-25
U5VXEBE0.book Page 26 Monday, August 8, 2005 10:32 AM
WARNING
Securely support the vehicle so that
there is no danger of it falling over.
6 2. Hold the lower ends of the front
fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.
6-26
U5VXEBE0.book Page 27 Monday, August 8, 2005 10:32 AM
6-27
U5VXEBE0.book Page 28 Monday, August 8, 2005 10:32 AM
1. Headlight fuse
2. Signaling system fuse
3. Ignition fuse
4. Radiator fan fuse
1. Main fuse 5. Backup fuse (for odometer, clock and immo-
2. Spare fuse bilizer system)
6 6. Fuel injection system fuse
The fuse box is located behind panel C. 7. Spare fuse
(See page 6-5.) 8. Parking lighting fuse
1. Fuse box
6-28
U5VXEBE0.book Page 29 Monday, August 8, 2005 10:32 AM
CAUTION: 1. Headlight bulb cover touch the bulb until it has cooled
2. Headlight coupler down.
Do not use a fuse of a higher amper-
age rating than recommended to 2. Unhook the headlight bulb holder, 3. Place a new headlight bulb into po-
avoid causing extensive damage to and then remove the defective sition, and then secure it with the
the electrical system and possibly a bulb. bulb holder.
ECA10650
fire.
CAUTION:
3. Turn the key to “ON” and turn on Take care not to damage the follow-
the electrical circuit in question to ing parts:
check if the device operates.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
6-29
U5VXEBE0.book Page 30 Monday, August 8, 2005 10:32 AM
Do not touch the glass part of and then connect the coupler. Replacing the tail/brake light
the headlight bulb to keep it free 5. Have a Yamaha dealer adjust the bulb
from oil, otherwise the transpar- headlight beam if necessary. 1. Remove the seat. (See page
ency of the glass, the luminosity 3-13.)
of the bulb, and the bulb life will 2. Remove the socket (together with
be adversely affected. Thor- the bulb) by turning it counter-
oughly clean off any dirt and fin- clockwise.
gerprints on the headlight bulb
using a cloth moistened with al-
cohol or thinner.
● Headlight lens
Do not affix any type of tinted
film or stickers to the headlight
lens.
6 Do not use a headlight bulb of a
wattage higher than specified.
1. Tail/brake light bulb socket
2. Muffler bracket cover
EWA12301
WARNING
Do not touch the muffler bracket un-
til the exhaust system has cooled.
3. Remove the defective bulb by
pushing it in and turning it counter-
clockwise.
1. Do not touch the glass part of the bulb.
6-30
U5VXEBE0.book Page 31 Monday, August 8, 2005 10:32 AM
push it in, and then turn it clock- Replacing a turn signal light Replacing the license plate
wise until it stops. bulb light bulb
5. Install the socket (together with the 1. Remove the turn signal light lens 1. Remove the license plate light unit
bulb) by turning it clockwise. by removing the screw. by removing the screws.
6. Install the seat.
1. Screw 1. Screw
2. License plate light unit 6
2. Remove the defective bulb by
pushing it in and turning it counter- 2. Remove the socket (together with
clockwise. the bulb) by pulling it out.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screw.
ECA11190
CAUTION:
Do not overtighten the screw, other-
wise the lens may break.
6-31
U5VXEBE0.book Page 32 Monday, August 8, 2005 10:32 AM
6-32
U5VXEBE0.book Page 33 Monday, August 8, 2005 10:32 AM
6-33
U5VXEBE0.book Page 34 Monday, August 8, 2005 10:32 AM
WARNING
● It is advisable to have a Yamaha
dealer service the wheel.
● Securely support the motor-
cycle so that there is no danger 1. Axle nut
of it falling over. 2. Drive chain slack adjusting nut
3. Locknut
1. Loosen the axle nut.
2. Place the motorcycle on the cen- 5. Push the wheel forward, and then
terstand. remove the drive chain from the
6 3. Remove the axle nut. rear sprocket.
4. Loosen the locknut and drive chain
adjusting nut on each side of the
swingarm.
6-34
U5VXEBE0.book Page 35 Monday, August 8, 2005 10:32 AM
6-35
U5VXEBE0.book Page 36 Monday, August 8, 2005 10:32 AM
Troubleshooting
Although Yamaha motorcycles receive
a thorough inspection before shipment
from the factory, trouble may occur dur-
ing operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your motorcycle
require any repair, take it to a Yamaha
dealer, whose skilled technicians have
6 the necessary tools, experience, and
know-how to service the motorcycle
properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look like
Yamaha parts, but they are often inferi-
or, have a shorter service life and can
lead to expensive repair bills.
6-36
U5VXEBE0.book Page 37 Monday, August 8, 2005 10:32 AM
Troubleshooting charts
WARNING
Keep away open flames and do not smoke while checking or working on the fuel system.
1. Fuel
There is enough fuel. Check the compression.
Check the fuel level in
the fuel tank.
The engine does not start.
There is no fuel. Supply fuel.
Check the compression.
2. Compression
There is compression. Check the ignition.
Operate the electric starter. 6
Have a Yamaha dealer
There is no compression.
check the vehicle.
3. Ignition Wipe off with a dry cloth and correct the Open the throttle halfway and operate
Wet
spark plug gaps, or replace the spark plugs. the electric starter.
Remove the spark plugs
and check the electrodes.
The engine does not start.
Dry Have a Yamaha dealer check the vehicle.
Check the battery.
6-37
U5VXEBE0.book Page 38 Monday, August 8, 2005 10:32 AM
WARNING
● Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
● After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the hissing
sound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
The coolant level Start the engine. If the engine overheats again, have a
6 is OK. Yamaha dealer check and repair the cooling system.
NOTE:
If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant
as soon as possible.
6-38
U5VXEBE0.book Page 1 Monday, August 8, 2005 10:32 AM
7-2
U5VXEBE0.book Page 3 Monday, August 8, 2005 10:32 AM
7-4
U5VXEBE0.book Page 1 Monday, August 8, 2005 10:32 AM
SPECIFICATIONS
Dimensions: Engine oil: Fuel:
Overall length: Type: Recommended fuel:
2095 mm (82.5 in) SAE10W30 or SAE10W40 or SAE15W40 Regular unleaded gasoline only
Overall width: or SAE20W40 or SAE20W50 Fuel tank capacity:
750 mm (29.5 in) 19.4 L (5.13 US gal) (4.27 Imp.gal)
Overall height: -20 -10 0 10 20 30 40 50 ˚C Fuel reserve amount:
1215 mm (47.8 in) 3.6 L (0.95 US gal) (0.79 Imp.gal)
SAE 10W-30
Seat height: Fuel injection:
795 mm (31.3 in) SAE 10W-40 Manufacturer:
Wheelbase: MIKUNI
1440 mm (56.7 in) SAE 15W-40 Model/quantity:
Ground clearance: 36EIDW x 2
SAE 20W-40
145 mm (5.71 in) Spark plug (s):
Minimum turning radius: SAE 20W-50 Manufacturer/model:
2800 mm (110.2 in) NGK/CR9EK
Weight: Spark plug gap:
With oil and fuel: Recommended engine oil grade:
0.6–0.7 mm (0.024–0.028 in)
207.0 kg (456 lb) API service SE, SF, SG type or higher
Engine oil quantity:
Clutch:
Engine: Clutch type:
Without oil filter cartridge replacement:
Engine type: Wet, multiple-disc
2.50 L (2.64 US qt) (2.20 Imp.qt)
Liquid cooled 4-stroke, DOHC Transmission:
With oil filter cartridge replacement:
Cylinder arrangement: Primary reduction system:
2.80 L (2.96 US qt) (2.46 Imp.qt)
Forward-inclined parallel 4-cylinder Spur gear
Displacement:
Cooling system:
Coolant reservoir capacity (up to the
Primary reduction ratio: 8
600.0 cm³ (36.61 cu.in) 86/44 (1.955)
maximum level mark):
Bore × stroke: Secondary reduction system:
0.27 L (0.29 US qt) (0.24 Imp.qt)
65.5 × 44.5 mm (2.58 × 1.75 in) Chain drive
Radiator capacity (including all routes):
Compression ratio: Secondary reduction ratio:
2.00 L (2.11 US qt) (1.76 Imp.qt)
12.20 :1 46/16 (2.875)
Starting system: Air filter:
Transmission type:
Electric starter Air filter element:
Constant mesh 6-speed
Lubrication system: Oil-coated paper element
Operation:
Wet sump Left foot operation
8-1
U5VXEBE0.book Page 2 Monday, August 8, 2005 10:32 AM
SPECIFICATIONS
Gear ratio: Manufacturer/model: Rear wheel:
1st: BRIDGESTONE/BT020R GG Wheel type:
37/13 (2.846) Manufacturer/model: Cast wheel
2nd: DUNLOP/D252 Rim size:
37/19 (1.947) Loading: 17M/C x MT5.50
3rd: Maximum load: Front brake:
28/18 (1.556) 190 kg (419 lb) Type:
4th: (Total weight of rider, passenger, cargo and Dual disc brake
32/24 (1.333) accessories) Operation:
5th: Tire air pressure (measured on cold Right hand operation
25/21 (1.190) tires): Recommended fluid:
6th: Loading condition: DOT 4
26/24 (1.083) 0–90 kg (0–198 lb) Rear brake:
Chassis: Front: Type:
Frame type: 225 kPa (33 psi) (2.25 kgf/cm²) Single disc brake
Diamond Rear: Operation:
Caster angle: 250 kPa (36 psi) (2.50 kgf/cm²) Right foot operation
25.00 ° Loading condition: Recommended fluid:
Trail: 90–190 kg (198–419 lb) DOT 4
97.5 mm (3.84 in) Front: Front suspension:
Front tire: 250 kPa (36 psi) (2.50 kgf/cm²) Type:
Type: Rear: Telescopic fork
Tubeless 290 kPa (42 psi) (2.90 kgf/cm²) Spring/shock absorber type:
8 Size: High-speed riding: Coil spring/oil damper
120/70 ZR17M/C (58W) Front: Wheel travel:
Manufacturer/model: 225 kPa (33 psi) (2.25 kgf/cm²) 130.0 mm (5.12 in)
BRIDGESTONE/BT020F GG Rear: Rear suspension:
Manufacturer/model: 250 kPa (36 psi) (2.50 kgf/cm²) Type:
DUNLOP/D252F Front wheel: Swingarm (monocross)
Rear tire: Wheel type: Spring/shock absorber type:
Type: Cast wheel Coil spring/gas-oil damper
Tubeless Rim size: Wheel travel:
Size: 17M/C x MT3.50 130.0 mm (5.12 in)
180/55 ZR17M/C (73W)
8-2
U5VXEBE0.book Page 3 Monday, August 8, 2005 10:32 AM
SPECIFICATIONS
Electrical system: Oil level warning light:
Ignition system: LED
Transistorized coil ignition (digital) Turn signal indicator light:
Charging system: LED
AC magneto Engine trouble warning light:
Battery: LED
Model: Immobilizer system indicator light:
GT12B-4 LED
Voltage, capacity: Fuses:
12 V, 10.0 Ah Main fuse:
Headlight: 30.0 A
Bulb type: Headlight fuse:
Halogen bulb 20.0 A
Bulb voltage, wattage × quantity: Signaling system fuse:
Headlight: 10.0 A
12 V, 60 W/55.0 W × 1 Ignition fuse:
Headlight: 10.0 A
12 V, 55.0 W × 1 Parking lighting fuse:
Tail/brake light: 10.0 A
12 V, 5.0 W/21.0 W × 1 Radiator fan fuse:
Front turn signal light: 20.0 A
12 V, 10.0 W × 2 Fuel injection system fuse:
Rear turn signal light: 10.0 A
12 V, 10.0 W × 2 Backup fuse: 8
Auxiliary light: 10.0 A
12 V, 5.0 W × 2
License plate light:
12 V, 5.0 W × 1
Meter lighting:
EL (LCD backlight)
Neutral indicator light:
LED
High beam indicator light:
LED
8-3
U5VXEBE0.book Page 1 Monday, August 8, 2005 10:32 AM
CONSUMER INFORMATION
EAU26351 EAU26381 EAU26400
9-1
U5VXEBE0.book Page 2 Monday, August 8, 2005 10:32 AM
CONSUMER INFORMATION
EAU26540
Model label
1. Model label
9-2
U5VXEBE0.book Page 1 Monday, August 8, 2005 10:32 AM
INDEX
A F P
Air filter element, replacing ................... 6-12 Front and rear brake pads, checking.... 6-18 Panels, removing and installing ..............6-5
Anti-theft alarm (optional)........................ 3-8 Front fork, checking .............................. 6-25 Parking ....................................................5-4
Auxiliary light bulb, replacing ................ 6-32 Fuel....................................................... 3-12 Part locations .......................................... 2-1
B Fuel consumption, tips for reducing........ 5-3 Pass switch ............................................. 3-9
Battery................................................... 6-27 Fuel tank breather hose........................ 3-13 Periodic maintenance and lubrication
Brake and clutch levers, Fuel tank cap ........................................ 3-11 chart......................................................6-2
checking and lubricating ..................... 6-24 Fuses, replacing ................................... 6-28 Pre-operation check list...........................4-2
Brake and shift pedals, H R
checking and lubricating ..................... 6-23 Handlebar switches ................................ 3-8 Rear brake light switch, adjusting ......... 6-18
Brake fluid, changing ............................ 6-20 Hazard switch ......................................... 3-9 S
Brake fluid level, checking .................... 6-19 Headlight bulb, replacing ...................... 6-29 Safety information ...................................1-1
Brake lever............................................ 3-10 High beam indicator light ........................ 3-4 Seat....................................................... 3-13
Brake pedal........................................... 3-11 Horn switch............................................. 3-9 Shifting ....................................................5-2
C I Shift pedal ............................................. 3-10
Cables, checking and lubricating .......... 6-22 Identification numbers ............................ 9-1 Shock absorber assembly, adjusting ....3-15
Care ........................................................ 7-1 Ignition circuit cut-off system ................ 3-16 Sidestand ..............................................3-16
Catalytic converter ................................ 3-13 Immobilizer system................................. 3-1 Spark plugs, checking .............................6-6
Centerstand and sidestand, Immobilizer system indicator light........... 3-4 Specifications .......................................... 8-1
checking and lubricating ..................... 6-24 Indicator and warning lights.................... 3-3 Starting the engine .................................. 5-1
Clutch lever ........................................... 3-10 K Start switch..............................................3-9
Clutch lever free play, adjusting............ 6-17 Key identification number ....................... 9-1 Steering, checking.................................6-26
Coolant.................................................. 6-10 L Storage....................................................7-3
D LCD tachometer ..................................... 3-5 Storage compartment............................ 3-14
Dimmer switch ........................................ 3-9 License plate light bulb, replacing ........ 6-31 Swingarm pivots, lubricating ................. 6-25
Drive chain, cleaning and lubricating .... 6-22 M T
Drive chain slack................................... 6-20 Main switch/steering lock........................ 3-2 Tail/brake light bulb, replacing ..............6-30
E Model label ............................................. 9-2 Throttle cable free play, checking ......... 6-14
Engine break-in....................................... 5-3 Multi-function display .............................. 3-5 Throttle grip and cable,
Engine idling speed............................... 6-13 N checking and lubricating ..................... 6-23
Engine oil and oil filter cartridge.............. 6-7 Neutral indicator light.............................. 3-3 Tires ......................................................6-14
Engine stop switch .................................. 3-9 O Tool kit..................................................... 6-1
Engine trouble warning light.................... 3-4 Oil level warning light.............................. 3-4 Troubleshooting .................................... 6-36
Troubleshooting charts.......................... 6-37
U5VXEBE0.book Page 2 Monday, August 8, 2005 10:32 AM
INDEX
Turn signal indicator lights ...................... 3-3
Turn signal light bulb, replacing............ 6-31
Turn signal switch................................... 3-9
V
Valve clearance .................................... 6-14
Vehicle identification number.................. 9-1
W
Wheel bearings, checking .................... 6-26
Wheel (front) ......................................... 6-33
Wheel (rear).......................................... 6-34
Wheels.................................................. 6-17
A5-yoko_Blank.fm Page 1 Tuesday, April 8, 2003 11:43 AM
A5-yoko_Blank.fm Page 1 Tuesday, April 8, 2003 11:43 AM
YAMAHA MOTOR CO., LTD.
PRINTED ON RECYCLED PAPER PRINTED IN JAPAN
2005.08-0.3×1 CR
(E)