Documente Academic
Documente Profesional
Documente Cultură
PAGE 12 / 12
Field Joint View
Supplied Product View
25 Bethridge Road, Toronto, Ontario, Canada M9W 1M7 Tel: (416) 743-7111 Fax: (416) 743-5927 www.canusacps.com
Installation Guide
CanusaWrap™
Two-piece protective bulk roll with separate closure
SOLVENT
(95°F) or below -20°C (-4°F). Product
installation should be done in accordance with
local health and safety regulations.
Bulk Roll Closure
CanusaWrapTM is typically shipped in bulk rolls. The These installation instructions are intended as a Propane tank, hose, torch & regulator Appropriate
adhesive is protected from contamination by an guide for standard products. Consult your Canusa tools for surface abrasion
inner liner. Closures are shipped either in bulk rolls representative for specific projects or unique Knife, roller, rags & Canusa approved solvent cleanser
or pre-cut. applications.
Digital thermometer with suitable probe
Standard safety equipment: gloves, goggles, hard hat,
etc.
SOLVENT
L
Corner Cuts
A <450mm Pipe O.D.
Pipe O.D.: B
A-50mm, B-25mm
Closure
<450mm (18")
Cut
Underlap
Overlap
100 mm overlap W
Sleeve
>450mm (18")
150 mm overlap
Sleeve >450mm Pipe O.D. width
A-100mm, B-50mm
As a guideline,cut the required lengths of Sleeve material (L)and Closure material (W) from the bulk roll as follows Ensure that the PE coating edges are beveled to 30°.
L = Coated Pipe circumference + overlap dimension W = Sleeve Width Clean exposed steel and adjacent pipe coating with a
solvent cleanser to remove the presence of oil,
Ensure that the sleeve and closure are not damaged or contaminated. Trim corners as shown . grease, and other contaminants.
Please see “CanusaWrapTM Sleeve Cutting Guideline” for more information on alternative cutting methods.
Surface Preparation and Pre-Heat Chart Flame Intensity & Torch Size
6 Standard Sleeves Surface Preparation Min. Pre-Heat Temp. 7
SIS Standard SSPC Standard °C (°F) Pipe O.D. Pipe O.D.
Minimum Preferred Minimum Preferred <450mm >450mm
WLG WTG St2 Sa2 SP2 SP6 50 (122) (18") (18")
WLC WTC St2 Sa2 SP2 SP6 60 (140)
Mastic
Ensure that the pipe is dry before cleaning. Wipe clean or air blast the steel and pipe coating to Pre-heat the joint area to the minimum required
Prepare the steel joint area using the Surface remove foreign contaminants. temperature (see Surface Preparation & Pre-Heat
Preparation and Pre-Heat as a guideline. Lightly Chart). Using a temperature measuring device,
abrade the pipe coating adjacent to the cutback ensure that the correct temperature is reached on
area to a distance of 50mm (2") beyond each end the steel and at least 50mm (2") on each side of the
of the sleeve width. sleeve.
1
2
Partially remove the release liner and gently heat Centre the sleeve over the joint so that the sleeve Wrap the sleeve loosely around the pipe, ensuring
the underlap approximately 150 mm (6") from the overlaps between the 10 and 2 o'clock positions. the appropriate overlap. Gently heat the backing of
edge. Press the underlap firmly into place and remove the the underlap and the adhesive side of the overlap.
remaining release liner. Press the overlap into place.
14 15A C E
B D F
Remove any release liners from the closure. Gently heat the closure and pat it down with a gloved hand. Repeating this procedure, move from one side to
Centre the closure on the overlapping sleeve. the other. Smooth any wrinkles by gently working them outward from the centre of the closure with a roller.
Press down firmly.
16 17 18
Pipe O.D.:
<450mm (18")
1 torch
>450mm (18")
2 torches
Using the appropriate sized torch, begin at the Continue heating from the centre toward one end Shrinking has been completed when the adhesive
centre of the sleeve and heat circumferentially of the sleeve until recovery is complete. In a begins to ooze at the sleeve edges all around the
around the pipe. Use broad strokes. If utilizing similar manner, heat and shrink the remaining side. circumference. Finish shrinking the sleeve with
two torches, operators should work on opposite long horizontal strokes over the entire surface to
sides of pipe. ensure a uniform bond.
Inspection
19 20 21
2
1
2
1
While the sleeve is still hot and soft, use a hand Continue the procedure by also firmly rolling the Visually inspect the installed sleeve for the following:
roller to gently roll the sleeve surface and push any closure with long horizontal strokes from the weld • Sleeve is in full contact with the steel joint.
trapped air up and out of the sleeve, as shown outwards. • Adhesive flows beyond both sleeve edges.
above. If necessary, reheat to roll out air. • No cracks or holes in sleeve backing.
Backfilling Guidelines
After shrinking is complete, allow the sleeve to cool for 2 hours prior to lowering and backfilling. To prevent damage to the sleeve, use selected backfill
material, (no sharp stones or large particles) otherwise an extruded polyethylene mesh or other suitable shield should be used.
www.canusacps.com