Documente Academic
Documente Profesional
Documente Cultură
Over the years, many DIN standards were integrated into the ISO standards, and thus
also a part of the EN standards. In the cource of the revision of the European standards
serveral DIN standards were withdrawn and replaced by DIN ISO EN and DIN EN.
The standards used in the past such as the DIN 17121, DIN 1629, DIN 2448 and the
DIN 17175 have since been mostly replaced by Euronorms. The Euronorms clearly
distinguish the pipe's area of application. Consequently different standards now exist for
pipes used as construction materials, pipelines or for mechanical engineering
applications.
This distinction was not as clear in the past. For example, the old St.52.0 quality was
derived from the DIN 1629 standard which was intended for pipeline systems and
mechanical engineering applications. This quality was also often used for steel
structures, however.
The info below explains the main standards and steel qualities under the new system of
standards.
The EN 10216 Euronorm replaces the old DIN 17175 and 1629 standards. This
standard is designed for pipes used in pressure applications, such as a pipeline. This is
why the associated steel qualities are designated by the letter P for 'Pressure'. The
value that follows this letter designates the minimum yield strength. The subsequent
letter designations provide additional information.
The EN 10216 comprises several parts. The parts that are relevant to us are as follows:
* Normalized is defined as: normalized (warm) rolled or standard annealing (at a min
temperature of 930°C). This applies to allqualities designated by the letter 'N' in the new
Euro Standards.
NEW STANDARD
DIN EN 10216-1
DIN EN 10216-3
DIN EN 10216-4
DIN EN 10216-5
DIN EN 10217-1
DIN EN 10217-2
DIN EN 10217-3
DIN EN 10217-4
DIN EN 10217-5
DIN EN 10217-6
DIN EN 10217-7
NEW STANDARD
DIN EN 10210-1
Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1:
Technical delivery conditions
This part of this European Standard specifies technical delivery conditions for hot
finished hollow sections of circular, square, rectangular or elliptical forms and applies to
hollow sections formed...
DIN EN 10210-2
Hot finished structural hollow sections of non-alloy and fine grain steels - Part 2:
Tolerances, dimensions and sectional properties
This part of EN 10210 specifies tolerances for hot finished circular, square, rectangular
and elliptical structural hollow sections, manufactured in wall thicknesses up to 120 mm,
in the following siz...
DIN EN 10219-1
Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 1:
Technical delivery conditions
This part of this European Standard specifies the technical delivery conditions for cold
formed welded structural hollow sections of circular, square or rectangular forms and
applies to structural hol...
DIN EN 10219-2
Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 2:
Tolerances, dimensions and sectional properties
This part of EN 10219 specifies tolerances for cold formed welded circular, square and
rectangular structural hollow sections, manufactured in wall thicknesses up to 40 mm, in
the following size range...
NEW STANDARD
DIN EN 10208-1
Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Part 1:
Pipes of requirement class A
This European Standard specifies the technical delivery conditions for seamless and
welded steel pipes for the on land transport of combustible fluids primarily in gas supply
systems but excluding pip...
DIN EN 10208-2
Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Part 2:
Pipes of requirement class B
This European Standard specifies the technical delivery conditions for seamless and
welded steel pipes for the on land transport of combustible fluids primarily in gas supply
systems but excluding pip...
DIN EN 10208-3
Steel pipes for pipe lines for combustible fluids - Technical delivery conditions - Part 3:
Pipes of class C
Specifies the technical delivery conditions for unalloyed and alloyed (except stainless)
seamless and welded steel pipes. It includes quality and testing requirements overall
higher than those specifi...
DIN EN 10253-1
Butt-welding pipe fittings - Part 1: Wrought carbon steel for general use and without
specific inspection requirements
The document specifies requirements for steel butt-welding fittings, namely elbows and
return bends, concentric reducers, equal and reducing tees, dished and caps.
DIN EN 10253-2
Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific
inspection requirements; German version EN 10253-2
This European Standard specifies in two parts the technical delivery conditions for steel
butt welding pipe fittings (elbows, return bends, concentric and eccentric reducers,
equal and reducing tees, and caps) which are intended for pressure purposes and for
the transmission and distribution of fluids and gases. The part 1 covers fittings of
unalloyed steels without specific inspection requirements. The part 2 covers fittings with
specific inspection requirements and offers two ways for determining the resistance to
internal pressure of the fitting.
DIN EN 10253-3
DIN EN 10253-4
DIN EN 1092-1
Flanges and their joints - Circular flanges for pipes, Valves, fittings and accessories, PN
designated - Part 1: Steel flanges; German version EN 1092-1:2007
This European standard specifies requirements for circular steel flanges in PN
designations PN 2,5 to PN 400 and nominal sizes from DN 10 to DN 4000. This
standard specifies the flange types and their facings, dimensions, tolerances, threading,
bolt sizes, flange face surface finish, marking, materials, pressure / temperature ratings
and flange masses.
DIN EN 1092-2
Circular flanges for pipes, Valves, fittings and accessories, PN designated - Part 2: Cast
iron flanges
The document specifies requirements for circular flanges made from ductile, grey and
malleable cast iron for DN 10 to DN 4000 and PN 2,5 to PN 63. It also specifies the
types of flanges and their facings, dimensions and tolerances, bolt sizes, surface finish
of jointing faces, marking, testing, quality assurance and materials together with
associated pressure/temperature (p/T) ratings.
DIN EN 1092-3
Flanges and their joints - Circular flanges for pipes, Valves, fittings and accessories, PN
designated - Part 3: Copper alloy flanges
This document specifies requirements for circular copper alloy flanges in PN
designations from PN 6 to PN 40 and nominal sizes from DN 10 to DN 1800.
DIN EN 1092-4
Flanges and their joints - Circular flanges for pipes, Valves, fittings and accessories, PN
designated - Part 4: Aluminium alloy flanges
This standard specifies requirements for PN designated circular flanges for pipes,
Valves, fittings and accessories made from aluminium alloy in the range of DN 15 to DN
600 and PN 10 to PN 63. This standard specifies the types of flanges and their facings,
dimensions and tolerances, bolt sizes, surface finish of faces, marking and materials
together with associated P/T ratings. The flanges are intended to be used for pipework
as well as for pressure vessels.