Documente Academic
Documente Profesional
Documente Cultură
1. Products introduction
Please read the instructions carefully before proceeding.
MCU is supplied to control the gate operator.
Keypad / single button interface.
Have Infrared safety sensor interface.
Soft start and soft stop function and the soft stop width are
adjustable, and the soft start function can be disabled.
Sliding Gate Operator Working time is adjustable.
Motor output torque is adjustable.
User's Manual Manual key release designed for emergency purposes.
occur.
gates.
1
SL600AC SLIDING GATE OPERATOR SL600AC SLIDING GATE OPERATOR
z Do not allow control devices to be placed so that a person can Duty cycle S2, 15 minutes
extra remote control 20
access them by reaching through the gate.
Environmental temperature -20°C~+50°C
z In the event of power failure, an emergency release key allows
Gate Move speed 12m/min 14m/min
you to operate the gate manually.
4. Mechanical Installation
z The operator should be switched off before repairing it or
The SL600AC will handle gate weighting up to 600kg and up to
opening its cover. 8m/12m if the proper installation procedures have been followed.
The SL600AC gate operator operates by forcing a drive rack by a
z Please erase and reprogram the transmitter code after installing drive gear. The entire configuration is shown in the diagram below.
the operator. The gate operator must be installed on the inside of the gate.
Switch
Make sure the Power supply (AC220V or AC110V) of the gate Wall
operator is suitable for the power supply in your area. Sliding gate
2 3
SL600AC SLIDING GATE OPERATOR SL600AC SLIDING GATE OPERATOR
Gate preparation
Gate operator
Be sure the gate is properly installed and slides smoothly before
installing the SL600AC sliding gate operator. The gate must be plumb,
level, and move freely. Gear Nut
Conduit Spring washer
In order to protect the cable, use PVC conduit for low voltage power Plain washer
cable and control wires. Conduit must be preset into the concrete Nut
Groundsill
when it is poured. Wires within the conduit shall be located or
protected so that no damage can result from contact with any rough
or sharp part. Input power
Concrete pad
The base unit of the gate operator requires a concrete pad in order to
Fig.2
maintain proper stability. The concrete pad should be approximately
Operator base (see Fig.3)
450mm x 300mm x 200mm deep in order to providing for adequate
After the concrete has hardened, mount the gate operator base to the
weight and structure to insure proper stable installation.
concrete pad. Verify that the base is properly leveled.
Anchors (see Fig.2)
Using bolts and washers mount the gate operator to the base and
You can use anchor bolts, anchors, washers and nuts. These
insert the cover. Check the operator and make sure it is lined up with
anchors must be set into the concrete when it is poured or you can
the gate.
use wedge anchors to fasten the operator.
Gate operator
Nut
Gear Spring washer
Plain washer
Groundsill Nut
Input power
Fig.3
4 5
SL600AC SLIDING GATE OPERATOR SL600AC SLIDING GATE OPERATOR
Installation of Rack z Release the gear with the key and push the sliding gate manually
z Fix the three nuts (in the same package with rack) on the rack to pre-determine the position, fix the block to the rack and lock
element. the gear by push up the release bar. Moving the gate electrically,
z Lay the first piece of rack on the gear and weld the first nut on the adjust the block to the proper position until the position of the
gate. opening and closing meet the requirement.
z Move the gate manually, checking if the rack is resting on the
gear, and weld the second and third nut. Magnetic limit switch
z Bring another rack element near to the previous one. Move the z To ensure safety, it is recommended to install limit switches at
gate manually and weld the three nuts as the first rack, thus both ends of the gate to prevent the gate from sliding out of the
proceeding until the gate is fully covered. rails. The rails must be installed horizontally.
z When the rack has been installed, to ensure it meshes correctly z Install the limit block as shown in Fig.5 and Fig.6. The magnetic
with the gear. of limit switch and blocks are used to control the position of the
z The space between rack and gear is about 0.5mm. gate.
z Release the gear with the key and push the sliding gate manually
to pre-determine the position, fix the block to the rack and lock
the gear by push up the release bar. Moving the gate electrically,
adjust the block to the proper position until the position of the
opening and closing meet the requirement.
Sliding gate
Spring of limit switch
limit block
Rack
Gear
Fig.4
5. Adjustment
Spring limit switch
z To ensure safety, it is recommended to install limit switches at
both ends of the gate to prevent the gate from sliding out of the
rails. The rails must be installed horizontally.
Spring limit switch
z Install the limit block as shown in Fig.5 and Fig.6. The spring limit
switch and blocks are used to control the position of the gate.
6 7
SL600AC SLIDING GATE OPERATOR SL600AC SLIDING GATE OPERATOR
Sliding gate release bar about 90 degree to open or close gate manually, use the
Magnetic release key as follow:
Limit block z Fit the supplied key in the lock.
Rack z Turn the key and pull down the release bar about 90°to release
Gear
the gear. (Note: Do not exceed 90°, be careful not to use too
much force, otherwise the release bar will be damaged.)
z Open and close the gate manually.
Note: If the gate bumps the mounting post and cannot be electric
opened, move the gate a few inches by hand, thus you can release
Magnetic limit switch the gate with the key, open and close the gate manually.
Fig.5
M6X10
Fig. 7
6. Wire Connecting
Make sure that the power is OFF before making any electrical
connections.
Magnetic limit switch
Remove the cover, perform the wiring (See Fig.8 and wiring notes for
Fig.6
control board) and replace the cover again.
Manual operation
In case of power failure use key unlock the lock and pull down the
8 9
SL600AC SLIDING GATE OPERATOR SL600AC SLIDING GATE OPERATOR
SL600ACU: AC110V
VR1 VR2 VR3 VR4 Learn button
ON c. Output power supply: 12VDC(7 of J5), COM (9 of J5), I.R. (8 of
U1
OFF
J5 is N.C Infrared)
J1
If the infrared beam is interrupted during closing, the gate will reverse
X1
HALL
S1
Open limit Limit infrared device; the infrared output signal must be N.C.
POWER
7 8 9 10 11 12 13
U2
LEARN
12
COM swtich
Close limit
C22
9 10 Loop detector
GND/COM From four-terminal Form two-terminal to the emitter power supply
Infared sensor
RL1
RL2
J5
Terminal J5
1 2 3 4 5 6
5 6
MOT
U3
Pedestrian switch
CAP
J6
C20
O/S/C switch 9 JUMP
Capacitor COM COM NC
8
OC2
1 2 3
NO
F3
Extral button OUT
MOT1
C19 OC1 switch 7 NC OR NO TX Emitter connecting
MOTOR MOT2 J4 F1
J2
MOT
COM Control board RX Receiver connecting
N
LAMP
Q3
Caution light
Fig.9 infrared Schematic diagram
L
PE PE N L
Protect Earth
VDR1
F2
POWER
d. Three-button switch / single-button switch (keypad): The
J3 T2 SL600AC is equipped with interfaces for three-button switch and
single-button switch (keypad).
To install the keypad attach one lead of your keypad to ‘5’ of
Fig.8 terminal J2 and the other to the ‘4(COM)’. The keypad will
Wiring notes of control board function in single channel mode.
a. Power Input (terminal J3): PE (Earth),L (Live),N (Neutral). For three-button switch installation, use the terminals for
SL600AC: AC220V multi-channel mode. Connect open wire of external button switch
SL600ACU:AC110V to ‘1 (OPEN)’ of terminal J2, connect close wire of switch to ‘2
b. Caution light: connect caution light wire to L and N of (CLOSE)’, connect stop wire of switch to ‘3(STOP)’, connect
LAMP(terminal J4) common wire of switch to ‘4(COM)’.
SL600AC: AC220V
10 11
SL600AC SLIDING GATE OPERATOR SL600AC SLIDING GATE OPERATOR
5 5 Terminal J6 terminal J4
Capacitor
V W
4 4 Com
Mot1
Motor
3 3 Stop Mot2
2 Single-button 2 Open Mot
COM
U
1 switch 1 Close
or keypad
Three-button
Control board Control board switch PE
Fig.10A Control
board Control board
e. Pedestrian switch terminal block
Connect pedestrian switch wire to 4 and 6 terminal of J2. press
Fig.11
the switch the door will open 1 meter when the door is closed.
f. Loop detector interface
terminal J2 Switch Connect wire see the Fig.11A
6
5
terminal J2
4 12
3
Pedestrian 11
2
switch 10 detector LOOP
1
9
output
Control board 8
Loop
terminal block 7
detector
Fig.10B
Control board
terminal block
Motor and capacitor (Terminal J2, J4): MOT COM (com), MOT1 Fig.11A
(Positive direction), MOT2 (Opposite direction), PE (Protect Earth), C The car through the loop the door will close itself when the door opened.
The car arrived the loop the door will reverse when the door closing, and
and C (capacitor). If the door move direction is wrong, please the door will auto closed after the car through the loop.
change the MOT1 and MOT2 of motor, and change the block of If the car stops on the loop the door can’t close.
12 13
SL600AC SLIDING GATE OPERATOR SL600AC SLIDING GATE OPERATOR
7. Tuning and operation Remote Pedestrian button: After you learn the transmitter, you
press the remote button 4 the door will open 1 meter when the
a. Adjust the Adjustable resistance (see Fig.8) door is closed.
z You can program/learn button 1, button 2, and button 3
VR1: For motor working total time adjustment. individually. If you learn button1, the button 1 and button 4 are
Clockwise rotation to increase, counter-clockwise rotation to reduce. enable, if you learn button 2 too, the button 2 and button 4 are
The total time can be set to 10 seconds as minimum and 90 second enable, the button 1 is disable.
Button 1
s as maximum.
Button 2
14 15
SL600AC SLIDING GATE OPERATOR SL600AC SLIDING GATE OPERATOR
Adjust the DIP switch(see Fig13B and table 1) DIP DIP-switch Function SET
ON
No soft start mode
(see Fig.13A)
1
OFF Soft start mode(need to power on
(see Fig.13A) reset).
1 2 3 4 1 2 3 4
ON
N.C. limit switch(spring limit)
(see Fig.13B)
2
OFF
N.O. limit switch(magnetic limit)
18 19
SL600AC SLIDING GATE OPERATOR SL600AC SLIDING GATE OPERATOR
11. Troubleshooting 11. Packing list
Trouble Possible causes Solutions After receiving the gate operator, you should make an
unpack-inspection, in which you should check whether the product
The door fails to
1. Make sure that was damaged. If you have any problem please contact our dealer.
open and close. 1. Power is OFF
power is ON. You should find the following items in our standard packing:
LED display 2. Fuse burn
2. Replace fuse.
does not light.
1. Infrared beam is 1. Remove
No. Item Quantity
obstructed. obstructions.
The door can SL600AC sliding gate
2. Infrared sensor 2. Make sure the
open fails to 1 1
function is enabling, but infrared sensor operator
close.
the sensor has not been function is disabling. 2 Transmitter 2
installed.
3 Release key 2
1. Replace the
1. Battery level may be User’s manual
Remote battery inside the 4 1
low
transmitter does transmitter.
2. Transmitter code is
not work. 2. Reprogram the
lost
transmitter.
The transmitter
operating Battery level may be
Replace battery.
distance is too low.
short.
20 21