Documente Academic
Documente Profesional
Documente Cultură
Wiring
Dimensions Installation Connections (The applicability of the electric terminals varies with the type of machine.)
In the pack: Do not connect anything to the terminals that are shaded gray.
*Main unit
Dimensions (mm) *Watertight packing Individual mounting (mm) Side-by-side mounting (waterproof not possible) (mm)
*Adapter Control output 1
+1
(64) *Instruction manual (48 x number of units - 2.5) 0 Relay output E5CC
4 60 *Terminal cover (Provided only for models with “-500” suffix only) To install the Controller so 250 VAC, 3 A (resistive load)
48 1.5 44.8 that it is waterproof, insert Auxiliary outputs 1, 2, and 3 1. Control outputs 5. Options
Voltage output (for driving SSR)
the Waterproof Packing. 12 VDC, 21 mA Relay outputs
+0.6
Controllers cannot be 250 VAC, two outputs: 3 A
0
Current output
waterproofed when they (resistive load) The E5CC is set for a K thermocouple (input type of 5)
45
0 to 20 mA DC Control output 2
60 min.
are mounted side by side. 4 to 20 mA DC 250 VAC, three outputs: 2 A by default. If a different sensor is used, an input error (s.err) will occur.
+0.6 Voltage output (for driving SSR) (resistive load) Check the setting of the Input Type parameter.
Load: 500 Ω max.
45 0 12 VDC, 21 mA
58
RX QX CX QQ *3 Auxiliary Outputs
0
One relay One voltage output One linear Two voltage outputs Auxiliary outputs 1 and 2 Auxiliary outputs 1, 2, and 3
45
Operation Menu Only the value set to the ins: Temperature Input Shift parameter is applied to the entire temperature input range.
Operation stopped. When the process value is 200°C, the process value is treated as 201.2°C after input shift if the input shift value
Input Type Initial Setting Level (Control/alarm are both stopped.) Check the wiring before turning ON the power supply.
is set to 1.2°C. The process value is treated as 198.8°C after input shift if the input shift value is set to -1.2°C.
0 to 20mA 26 Use the following ranges for scaling: -1999 *6 Value Monitor *6 M M
M
1 to 5V 27 to 9999, -199.9 to 999.9, -19.99 to 99.99, cntl PID/ONOFF
In ON/OFF control = onof *6 tr-t Transfer
0.0 (unit: A) *7 0
Upper Limit 3 *4
Voltage input 0 to 5V 28 -1.999 to 9.999 onof In 2-PID control = pid off
Output Type
M M *6 hb2 Heater Burnout Detection 2
*6 rss Remote SP
*6 mv-e MV at PV Error
Input Shift
0 to 10V 29 M Standard or Heating/Cooling M Heater Current 2 0.0 (unit: A) *7 0.0 0.0
*6 ct2 Value Monitor *6 al3l Alarm Value
M M M
*The default is“5”. s-hc Standard control = stnd tr-h Transfer Output 0.0 (unit: A) *7 0
Lower Limit 3 *4
*s.err will be displayed when a platinum resistance thermometer is mistakenly connected stnd Heating and cooling control = h-c
*6
100.0 Upper Limit M M *6 lcr1 Leakage Current 1 Value
*6 rsrt Remote SP Slope *6 sprt SP Ramp Set Value
(Select standard control or heating Monitor (unit: A) *7 Coefficient
while input type is not set for it. To clear the s.err display, correct the wiring and cycle the M M Leakage Current 1 0.0 1.000 off
power supply.
and cooling control as required)
*6 lcr1 Value Monitor *6 al-4 Alarm Value 4 *4 M M M
st ST (Self-Tuning) tr-l Transfer Output 0.0 (unit: A) *7 0
*6 ST ON = on
on ST OFF = off
*6
0.0 Lower Limit M M *6 hs1 HS Alarm 1
*6 p Proportional
*6 sprl SP Ramp Set Value
(unit: A) *7 Band (SP Ramp Fall Value)
50.0 8.0 same
Alarms M M
*6 lcr2 Leakage Current 2
Value Monitor *6 al4h Alarm Value
M M M
Alarm output function ptrn ev-1 Event Input 0.0 (unit: A) *7 0
Upper Limit 4 *4
Setting Alarm type off
Program Pattern *6
msp0 Assignment 1 M M *6 lcr2 Leakage Current 2 Value
*6 i Integral Time *6 ol-h MV Upper Limit
Positive alarm value (X) Negative alarm value (X) Monitor (unit: A) *7 (Unit: secs)
M M 0.0 233 100.0
0 No alarm function Output off *6 prst Program Start *6 al4l Alarm Value
M M M
cp Control Period (Heating) ev-2 Event Input rset 0
Lower Limit 4 *4
Vary with
*6
20
(Unit: Seconds) *6
stop Assignment 2 M M *6 hs2 HS Alarm 2
*6 d Derivative Time
(Unit: secs) *6 ol-l MV Lower Limit
*1 1 Deviation upper/lower limit ON *Voltage output (for driving SSR): 2 (unit: A) *7
OFF
L H
"L", "H" values M M
50.0 40 0.0
SP
X X Control Period (Cooling) *6 sktr Soak Time Remain *6 o MV Monitor
M M M
2 Deviation upper limit ON ON c-cp ev-3 Event Input 0 0.0 (Heating)
sp-0
OFF
SP
OFF
SP
*6
20
(Unit: Seconds) *6
none Assignment 3 M M *6
SP 0
*6 c-p Proportional
(Cooling)
Band
*6 orl MV Change
*Voltage output (for driving SSR): 2 Rate Limit
X X 0 8.0 0.0
3 Deviation lower limit ON
OFF
ON
OFF
M
Direct/Reverse Operation
M
*6 r-s RUN/STOP
When control start = run *6 c-o MV Monitor
M M M
SP SP
orev ev-4 Event Input run When control stop = stop 0.0 (Cooling)
Integral Time
*1 4 Deviation upper/lower range ON
L H
Vary with
or-r
In Reverse operation (Heating) = or-r *6
none Assignment 4 M M *6 sp-1 SP 1
*6 c-i (Cooling) *6 sqrp Extraction of Square
OFF "L", "H" values In Direct operation (Cooling) = or-d Root Low-cut Point
SP
M
0 233 (unit: s) 0.0
M al-1
Deviation upper/lower limit ON
L H Vary with Extraction of Square *6 Alarm Value 1 *4 M M M
*1 5
standby sequence ON OFF "L", "H" values alt1 Alarm 1 Type: *3 sqr Root Enable 0 sp-2 Derivative Time
SP
X X
*6
2 Specified models only *4
*6
off
(Only when analog
M *6
SP 2
*6 c-d (Cooling) Adjustment level is for entering set
input is set)
6 Deviation upper limit ON ON 0 40 (unit: s)
values and shift values for control.
standby sequence ON OFF OFF M M al1h Alarm Value Upper Limit 1
SP SP
Move to Advanced
*6
*4
M M
7 Deviation lower limit ON
X
ON
X
*6 alh1 Alarm 1 Hysteresis *6 amov Function Setting 0
standby sequence ON OFF OFF
SP SP 0.2 0 Level M
8 Absolute value upper limit ON
X
ON
X M M
Operation level should normally be used during operations.
Error Display (troubleshooting)
OFF
0
OFF
0 *6 alt2 Alarm 2 Type: *3 When an error has occurred, the No.1 display shows the error code. Take necessary measure
X X Specified models only *4 according to the error code, referring the table below.
9 Absolute value lower limit ON ON 2
OFF
0
OFF
0 M Hold O and M keys Hold O and M keys Status at error
No.1 display Meaning Action
X X down for at least down for at least Control
10 Absolute value upper limit ON
OFF
ON
OFF *6 alh2 Alarm 2 Hysteresis 1 second 3 seconds output Alarm
standby sequence ON 0 0
0.2 Check the setting of the Input Type parameter, Operates
Absolute value lower limit X X s.err (S. Err) Input error check the input wiring, and check for broken or OFF as above the
11
standby sequence ON
ON
OFF 0
ON
OFF 0
M Protect Level *2 shorts in the temperature sensor. upper limit.
Initial setting level enables users to specify their preferred After the correction of A/D converter error, turn the
12 LBA (only for alarm 1) operating conditions (input type, alarm type, control method, etc.) Move to Protect Level A/D converter error
power OFF then back ON again. If the display
remains the same, the controller must be repaired. OFF OFF
pmov Displayed only when a chgp Changed
Parameters Only
e333 (E333) *2 If the display is restored to normal, then a
password is set. Restricts probable cause can be external noise affecting the
13 PV Change Rate Alarm 0 moving to Protect Level. off control system. Check for external noise.
*3: Refer to the adjoining tables for details of input types and alarm types. M M
Operation / Adjustment Protect Parameter Mask
X X *4: Applicable only to models with alarm functions. Turn the power OFF then back ON again. If the
14 SP absolute value upper limit ON
OFF
0
ON
OFF
0 *5: Operation is stopped when moved to the initial setting level. oapt Restricts displaying and
modifying menu items in pmsk Enable
Displayed only
display remains the same, the controller must be
(control/alarm are both stopped.) 0 Operation, Adjustment, on when a parameter e111 (E111) Memory error repaired. If the display is restored to normal, then OFF OFF
X X and Manual Control Levels. a probable cause can be external noise affecting
15 SP absolute value lower limit ON ON M mask is set.
OFF OFF *6: The grayed-out setting items are not displayed for some models and M the control system. Check for external noise.
0 0 Initial Setting / Communication Protect Move to Protect
ON
X
ON
X some settings of other setting items. icpt Restricts movement to the prlp Level If the input value exceeds the display limit (-1999 to 9999), though it is within the control
16 MV absolute value upper limit *7: Applicable only to models with heater burnout functions. Initial Setting, Communications Password to Move
OFF OFF
0
1 Setting, and Advanced Function 0 to Protect Level: range, [[[[ will be displayed under -1999 and ]]]] above 9999. Under these conditions,
0
*8: The four numeric digits of the product code are displayed in the No. 2 M Setting Levels. M control output and alarm output will operate normally.
X X
ON display. The setting cannot be changed and there is nothing that you
17 MV absolute value lower limit OFF
ON
OFF wtpt Setting Change Protect Refer to the E5CC/E5EC Digital Controllers User’s Manual (Cat. No. H174) for the controllable
0 0 need to set. Restricts changes to settings ranges.
ON
X
ON
X off by operating the front panel keys.
18 RSP absolute value upper limit OFF OFF M *2: Error shown only for "Process value / Set point". Not shown for other status.
0 0