Sunteți pe pagina 1din 26

Internal Use Only

North/Latin America http://aic.lgservice.com


Europe/Africa http://eic.lgservice.com
Asia/Oceania http://biz.lgservice.com

COLOR MONITOR
SERVICE MANUAL
CHASSIS NO. : LM14B
MODEL: 23MP67HQ
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

P/NO : MFL68801102(1410-REV00) Printed in China


CONTENTS

CONTENTS .............................................................................................. 2

PRECAUTION............................................................................................3

SERVICING PRECAUTIONS.....................................................................4

SPECIFICATIONS......................................................................................6

TIMING CHART .......................................................................................11

ADJUSTMENT .........................................................................................14

BLOCK DIAGRAM...................................................................................18

TROUBLE SHOOTING ............................................................................19

EXPLODED VIEW .................................................................................. 22

SVC. SHEET ...............................................................................................

Copyright © 2010 LG Electronics. Inc. All right reserved.


Only for training and service purposes
-2- LGE Internal Use Only
PRECAUTION
WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING

• There are some special components used in LCD monitor that BE CAREFUL ELECTRIC SHOCK !
are important for safety. These parts are marked on the
• If you want to replace with the new backlight (CCFL) or LIPS
schematic diagram and the Exploded View. It is essential
part, must disconnect the AC power because high voltage
that these critical parts should be replaced with the
appears at inverter circuit about 650Vrms.
manufacturer’s specified parts to prevent electric shock, fire or
other hazard.
• Handle with care wires or connectors of the inverter circuit. If
• Do not modify original design without obtaining written the wires are pressed cause short and may burn or take fire.
permission from manufacturer or you will void the original parts
Leakage Current Hot Check Circuit
and labor guarantee.
AC Volt-meter

TAKE CARE DURING HANDLING THE LCD MODULE WITH


Good Earth Ground
BACKLIGHT UNIT. such as WATER PIPE,
To Instrument's CONDUIT etc.
exposed 0.15uF
• Must mount the module using mounting holes arranged in four METALLIC PARTS
corners.
1.5 Kohm/10W
• Do not press on the panel, edge of the frame strongly or electric
shock as this will result in damage to the screen.
When 25A is impressed between Earth and 2nd Ground
for 1 second, Resistance must be less than 0.1 Ω
• Do not scratch or press on the panel with any sharp objects,
*Base on Adjustment standard
such as pencil or pen as this may result in damage to the panel.

• Protect the module from the ESD as it may damage the


electronic circuit (C-MOS).

• Make certain that treatment person’s body are grounded


through wrist band.

• Do not leave the module in high temperature and in areas of


high humidity for a long time.

• The module not be exposed to the direct sunlight.

• Avoid contact with water as it may a short circuit within the


module.

• If the surface of panel become dirty, please wipe it off with a


softmaterial. (Cleaning with a dirty or rough cloth may damage
the panel.)

CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.

Copyright © 2010 LG Electronics. Inc. All right reserved.


Only for training and service purposes
-3- LGE Internal Use Only
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service 2. After removing an electrical assembly equipped with ES
manual and its supplements and addenda, read and follow the devices, place the assembly on a conductive surface such as
SAFETY PRECAUTIONS on page 3 of this publication. aluminum foil, to prevent electrostatic charge buildup or
exposure of the assembly.
NOTE: If unforeseen circumstances create conflict between the 3. Use only a grounded-tip soldering iron to solder or unsolder ES
following servicing precautions and any of the safety precautions on devices.
page 3 of this publication, always follow the safety precautions. 4. Use only an anti-static type solder removal device. Some solder
Remember: Safety First. removal devices not classified as "anti-static" can generate
electrical charges sufficient to damage ES devices.
General Servicing Precautions 5. Do not use freon-propelled chemicals. These can generate
1. Always unplug the receiver AC power cord from the AC power electrical charges sufficient to damage ES devices.
source before; 6. Do not remove a replacement ES device from its protective
a. Removing or reinstalling any component, circuit board package until immediately before you are ready to install it.
module or any other receiver assembly. (Most replacement ES devices are packaged with leads
b. Disconnecting or re-connecting any receiver electrical plug or electrically shorted together by conductive foam, aluminum foil
other electrical connection. or comparable conductive material).
c. Connecting a test substitute in parallel with an electrolytic 7. Immediately before removing the protective material from the
capacitor in the receiver. leads of a replacement ES device, touch the protective material
CAUTION: A wrong part substitution or incorrect polarity to the chassis or circuit assembly into which the device will be
installation of electrolytic capacitors may result in an installed.
explosion hazard. CAUTION: Be sure no power is applied to the chassis or circuit,
and observe all other safety precautions.
2. Test high voltage only by measuring it with an appropriate high 8. Minimize bodily motions when handling unpackaged
voltage meter or other voltage measuring device (DVM, replacement ES devices. (Otherwise harmless motion such as
FETVOM, etc) equipped with a suitable high voltage probe. the brushing together of your clothes fabric or the lifting of your
Do not test high voltage by "drawing an arc". foot from a carpeted floor can generate static electricity
3. Do not spray chemicals on or near this receiver or any of its sufficient to damage an ES device.)
assemblies.
4. Unless specified otherwise in this service manual, clean General Soldering Guidelines
electrical contacts only by applying the following mixture to the 1. Use a grounded-tip, low-wattage soldering iron and appropriate
contacts with a pipe cleaner, cotton-tipped stick or comparable tip size and shape that will maintain tip temperature within the
non-abrasive applicator; 10% (by volume) Acetone and 90% (by range or 500ºF to 600ºF.
volume) is opropyl alcohol (90%-99% strength) 2. Use an appropriate gauge of RMA resin-core solder composed
CAUTION: This is a flammable mixture. of 60 parts tin/40 parts lead.
Unless specified otherwise in this service manual, lubrication of 3. Keep the soldering iron tip clean and well tinned.
contacts in not required. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
5. Do not defeat any plug/socket B+ voltage interlocks with which bristle (0.5 inch, or 1.25cm) brush with a metal handle.
receivers covered by this service manual might be equipped. Do not use freon-propelled spray-on cleaners.
6. Do not apply AC power to this instrument and/or any of its 5. Use the following unsoldering technique
electrical assemblies unless all solid-state device heat sinks are a. Allow the soldering iron tip to reach normal temperature.
correctly installed. (500ºF to 600ºF)
7. Always connect the test receiver ground lead to the receiver b. Heat the component lead until the solder melts.
chassis ground before connecting the test receiver positive c. Quickly draw the melted solder with an anti-static, suction-
lead. type solder removal device or with solder braid.
Always remove the test receiver ground lead last. CAUTION: Work quickly to avoid overheating the circuit
8. Use with this receiver only the test fixtures specified in this board printed foil.
service manual. 6. Use the following soldering technique.
CAUTION: Do not connect the test fixture ground strap to any a. Allow the soldering iron tip to reach a normal temperature
heat sink in this receiver. (500ºF to 600ºF)
b. First, hold the soldering iron tip and solder the strand against
Electrostatically Sensitive (ES) Devices the component lead until the solder melts.
Some semiconductor (solid-state) devices can be damaged easily c. Quickly move the soldering iron tip to the junction of the
by static electricity. Such components commonly are called component lead and the printed circuit foil, and hold it there
Electrostatically Sensitive (ES) Devices. Examples of typical ES only until the solder flows onto and around both the
devices are integrated circuits and some field-effect transistors and component lead and the foil.
semiconductor "chip" components. The following techniques CAUTION: Work quickly to avoid overheating the circuit
should be used to help reduce the incidence of component board printed foil.
damage caused by static by static electricity. d. Closely inspect the solder area and remove any excess or
splashed solder with a small wire-bristle brush.
1. Immediately before handling any semiconductor component or
semiconductor-equipped assembly, drain off any electrostatic
charge on your body by touching a known earth ground.
Alternatively, obtain and wear a commercially available
discharging wrist strap device, which should be removed to
prevent potential shock reasons prior to applying power to the
unit under test.
Copyright © 2010 LG Electronics. Inc. All right reserved.
Only for training and service purposes
-4- LGE Internal Use Only
IC Remove/Replacement Circuit Board Foil Repair
Some chassis circuit boards have slotted holes (oblong) through Excessive heat applied to the copper foil of any printed circuit
which the IC leads are inserted and then bent flat against the board will weaken the adhesive that bonds the foil to the circuit
circuit foil. When holes are the slotted type, the following technique board causing the foil to separate from or "lift-off" the board. The
should be used to remove and replace the IC. When working with following guidelines and procedures should be followed whenever
boards using the familiar round hole, use the standard technique this condition is encountered.
as outlined in paragraphs 5 and 6 above.
At IC Connections
Removal To repair a defective copper pattern at IC connections use the
1. Desolder and straighten each IC lead in one operation by gently following procedure to install a jumper wire on the copper pattern
prying up on the lead with the soldering iron tip as the solder side of the circuit board. (Use this technique only on IC
melts. connections).
2. Draw away the melted solder with an anti-static suction-type
solder removal device (or with solder braid) before removing the 1. Carefully remove the damaged copper pattern with a sharp
IC. knife. (Remove only as much copper as absolutely necessary).
Replacement 2. carefully scratch away the solder resist and acrylic coating (if
1. Carefully insert the replacement IC in the circuit board. used) from the end of the remaining copper pattern.
2. Carefully bend each IC lead against the circuit foil pad and 3. Bend a small "U" in one end of a small gauge jumper wire and
solder it. carefully crimp it around the IC pin. Solder the IC connection.
3. Clean the soldered areas with a small wire-bristle brush. 4. Route the jumper wire along the path of the out-away copper
(It is not necessary to reapply acrylic coating to the areas). pattern and let it overlap the previously scraped end of the good
copper pattern. Solder the overlapped area and clip off any
"Small-Signal" Discrete TransistorRemoval/Replacement excess jumper wire.
1. Remove the defective transistor by clipping its leads as close as
possible to the component body. At Other Connections
2. Bend into a "U" shape the end of each of three leads remaining Use the following technique to repair the defective copper pattern
on the circuit board. at connections other than IC Pins. This technique involves the
3. Bend into a "U" shape the replacement transistor leads. installation of a jumper wire on the component side of the circuit
4. Connect the replacement transistor leads to the corresponding board.
leads extending from the circuit board and crimp the "U" with
long nose pliers to insure metal to metal contact then solder 1. Remove the defective copper pattern with a sharp knife.
each connection. Remove at least 1/4 inch of copper, to ensure that a hazardous
condition will not exist if the jumper wire opens.
Power Output, Transistor Device 2. Trace along the copper pattern from both sides of the pattern
Removal/Replacement break and locate the nearest component that is directly
1. Heat and remove all solder from around the transistor leads. connected to the affected copper pattern.
2. Remove the heat sink mounting screw (if so equipped). 3. Connect insulated 20-gauge jumper wire from the lead of the
3. Carefully remove the transistor from the heat sink of the circuit nearest component on one side of the pattern break to the lead
board. of the nearest component on the other side.
4. Insert new transistor in the circuit board. Carefully crimp and solder the connections.
5. Solder each transistor lead, and clip off excess lead. CAUTION: Be sure the insulated jumper wire is dressed so the
6. Replace heat sink. it does not touch components or sharp edges.

Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close as
possible to diode body.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.

Fuse and Conventional Resistor


Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.
3. Solder the connections.
CAUTION: Maintain original spacing between the replaced
component and adjacent components and the circuit board to
prevent excessive component temperatures.

Copyright © 2010 LG Electronics. Inc. All right reserved. -5- LGE Internal Use Only
Only for training and service purposes
SPECIFICATIONS
1. General Specification
No Item Content Remark
1 Customer BRAND
2 User Model Name 23MP67HQ
3 Sale region Refer to Suffix standard
4 Feature 23”Wide LCD MONITOR
5 Chassis Name LM14A/B
General External SW Joystick New OSD (Menu, Picture Mode, Input, monito
Scope &Adj. r off)
Function OSD,DDC2B,DDC2AB, HDCP, Control Lock,
6
Original Ratio / Wide, Black level, Smart Energy Saving
Screen Split, SUPER RESOLUTION+,Color Wizard,
Reader mode,LG Color Cloning

Power Cord Length : 1.5±0.05 M Refer to Suffix


7 Shape : Wall-out standard and power
Color : Black cord table

Length : 1.5m
Signal Cable Shape : Detachable Type Refer to Suffix
(D-SUB) Color : Black standard
Pin : Triple Row, 15 Pin D-Sub

Length : 1.5m
Signal Cable Shape : Detachable Type Refer to Suffix
(DVI) Color : Black standard
Pin : Triple Row, 24 Pin DVI

8 Cable Length : 1.8m


Signal Cable Shape : Detachable Type Refer to Suffix
(HDMI) Color : Black standard
Pin : 19Pin HDMI

Audio Length : ,Shape : ,Color: ,Pin Do not Support

TV Length : ,Shape : ,Color: ,Pin Do not Support

Input: AC100~240V 50~60Hz,1.0A Max;DC 19V 1.3A Refer to Suffix


9 Power
Output: DC 19V 1.3A standard

P/No Specification

normal EAJ63128601 LM230WF3-SSG1’


10 Applying module list

Panel
biz

Copyright © 2010 LG Electronics. Inc. All right reserved.


Only for training and service purposes
-6- LGE Internal Use Only
2. Mechanical specification
No Item Content Remark
Width (W) Length (D) Height (H)
Product Before Packing 53.3cm 20.5cm 42.6cm With stand
1
Dimension 53.3cm 5.2cm 32.4cm Without stand
After Packing 60.2cm 12.6cm 38.4cm
Product Only SET 3.2kg
2
Weight With BOX 4.4kg
3 Container 20ft 40ft HC

Loading Individual or Indi. Pallet Indi. Pallet

Quantity Palletizing
- 640 - 1748
4 Stand Type Base detachable & Body detachable
Assy Size (W x D x H) 23.8 X 20.5 X 1.9cm Only stand base
Tilt Degree -3(±3) ~ 20(±3) degree
Tilt force 0.8~1.2kgf
Folding Degree N/A
5 Appearance General

3. Optical Character
No Item Criteria Remark
Viewing Angle Horizontal(R/L) : 178º (Typ.)
1
<CR≥10> Vertical(Top/Bottom) : 178º (Typ.)
2 Luminance(휘도) Average Luminance 200(min), 250 (Typ.) Warm
2
(cd/m ) (Full white pattern, 0.7V) (6500K)
Average Luminance 150 (min) Medium
2
(cd/m ) (Full white pattern, 0.7V) (8000K)
Average Luminance 150(min) Cool
2
(cd/m ) (Full white pattern, 0.7V) (9300K)
Smart Energy Sav Efficiency :
ing(high/low) Low:10%~20%
High:20%~30%

Luminance
75%(min),
Uniformity
3 Contrast Ratio(명암 비) 600(MIN), 1000(TYP), DFC->5,000,000:1(Typ.)
Gray to Gray: 14ms(Average),
-. Low : 9 ms ~ 11 ms
4 Response Time -. Middle : 7 ms ~ 9 ms
-. High : 5.5 ms ~ 6.5 ms

Copyright © 2010 LG Electronics. Inc. All right reserved.


Only for training and service purposes
-7- LGE Internal Use Only
4. Engineering Specification
Supported Sync.
1 Separate Sync., Digital
Type
30 ~ 61kHz (19”)
Analog/Digita Horizontal
30 ~ 83kHz (20”~27”)
l
Operating Vertical 56 ~ 75 Hz
2
Frequency Horizontal 30 ~ 83kHz
HDMI PC 56 ~ 61Hz
Vertical
AV 50 ~ 61Hz
Max. 1920x1080 @ 60Hz(22”~27”)
Analog/Digita
l
Recommend 1920x1080 @ 60Hz(22”~27”)
3 Resolution

Max. 1920×1080 @ 60Hz


HDMI
Recommend 1920×1080 @ 60Hz
4 Input Voltage Voltage :100 – 240 Vac, 50 or 60Hz, 1.0A
5 Inrush Current Cold Start : 50 A Hot : 120 A
6 L
Operating Sync
Video E Wattage
Condition (H/V)
D
Typ. Max.
Model Test condition
(W) (W)
1.1920x1080@60Hz
23MP67HQ 23W 29W (22/24)
2. burst pattern
3. 100~240V
4. After aging 30min

W
Activ
On Mode On/On hit
e
e

Test condition
1.1920x1080@60Hz
(22/24)
2. EPA6.0 10mins V
edio
3. 100~240V
4. After aging 30min

Copyright © 2010 LG Electronics. Inc. All right reserved.


Only for training and service purposes
-8- LGE Internal Use Only
측정방법) 제어판 
W
hit 전원 옵션에서 디스
e 플레이 끄기와 PC를
Off/On
Sleep Mode 절전모드로 하기 두
On/Off Off ≤ 0.3W
(D-SUB , HDMI) Bli 가지 설정이 있는데,
Off/Off
nk PC를 절전모드로 하
in 기만 선택하고 측정
g
해야 함.
Off Mode Of
- - ≤ 0.3W
(Power switch off) f
Efficiency : -Test Condition
Low:10%~20% (1)
High:20%~30%
W
Smart Energy 23MP67HQ:
High /Low/Off Low hit
Saving SES Low:2W/H SES high:4W/H
e

23MP67HQ:
21W 200nits :margin >7%
EPA
Worst :margin>0

7 MTBF 30,000 HRS with 90% Lamp Life : 30,000 Hours(Min)


Confidence level
8 Using Altitude 5,000 m (for Reliability) 3,000m(for FOS)

9 Environmen 0 Temperature 10 C ~ 35 C
t p Humidity 10% ~ 80%
Condition er
at
in
-g
St Temperature -20 C ~ 60 C
or Humidity 5% ~ 90% non-condensing
a
g
e
M BRIGHTNESS 0 ~ 100 17 Language:
E WARM English, Germanic,
N PRESET MEDIUM French, Spanish,
U COOL Italian, Swedish,
OSD COLOR TEMP
( RED Finnish, Portuguese
MENU
M USER GREEN Brazilian Portuguese,
on BLUE Polish, Russian,
ito WIDE Greek, Chinese,
r ORIGINAL RATIO Japanese, Korean,
ORIGINAL

Copyright © 2010 LG Electronics. Inc. All right reserved.


Only for training and service purposes
-9- LGE Internal Use Only
bl ▶ HIGH / LOW Ukrainian
oc BLACK LEVEL (BLACK LEVEL enable at HDMI Hindi
k) input)
LANGUAGE ▶ ENGLISH
FACTORY RESET ▶ NO( /YES )
CHANNEL
2~69(AIR) / 1 ~ 125(CABLE)
ADD/DEL CH
Function Support:
CHANNEL ADD/DELETE
No
AUTO CHANNEL ON/OFF
SELECT AIR/CABLE
FINE TUNE 0 ~ 100
CONTRAST 0~100
M BRIGHTNES
0~100
E S Function Support:
ADJUSTMENT
N SHARPNESS 0~100 No
U COLOR 0~100
(A TINT 0~100
V/
VOLUME 0~100
T
BASS 0~100
V
TREBLE 0~100 Function Support:
bl AUDIO
MUTE ON/OFF No
oc
k) SOUND
MONO/STEREO
LANGUAGE▶
English/German/French/Esperanto
Italian/Korean…
Function Support:
SETUP IMAGE SIZE ▶ FULL/1:1
No
OSD POSITION
TRANSPAREN
0~100
CY

Copyright © 2010 LG Electronics. Inc. All right reserved.


Only for training and service purposes
-10 - LGE Internal Use Only
5. Applying module Character
No Item Content Remark
Maker LGD
Type TFT
Active Display Area 23 inches(58.42 cm) diagonal
Pixel Pitch [mm] 0.2652 mm x 0.2652(V) mm
Electrical Interface 2ch-LVDS
Color Depth 6-bit with A-FRC, 16.7M colors
LCD Module Size (Outline) [mm] 527(H) x 309.8 (V) x 8.9 (D) mm
1
Feature
Hard coating(3H), Anti-glare treatment of
Surface Treatment
the front polarizer
Operating Mode Transmissive mode, normally Black
Back light Unit White LED
Typical 14ms
R/T
Max. 25ms
Minimum Normal Maximum
WX 0.313 Warm
White Typ-0.03 Typ+0.03
WY 0.329 (6500K)
WX 0.302
Medium
White WY Typ-0.03 0.311 Typ+0.03
(8000K)
WX 0.283
Cool
White WY Typ-0.03 0.298 Typ+0.03
CIE Color (9300K)
6 Coordinates WX 0.365
White Typ+0.03 Read1
(색 좌표) WY Typ-0.03 0.360
WX 0.353
White Typ+0.03 Read2
WY Typ-0.03 0.367
RX 0.653
Red
RY 0.337
GX 0.322
Green Typ-0.03 Typ+0.03
GY 0.611
BX 0.153
Blue
BY 0.061

(1) Standard Measurement Condition


• Ambient Luminance Level : dark ( < 10 lux)
• Ambient Temperature : Normal Temperature(10ºC ~ 25ºC)
• warm-up Time : More than 30 min (at Full White Pattern)
• Input Signal : VESA 1920 X 1080 @ 60 Hz
• Contrast : 70 (But, the contrast is 100 when we check response time)
• Brightness : Max. 100
• Color Temp : CUSTOM
• Clock/Clock Phase : The Best Setting
(2) Another Spec.: Product Specification Standard( LG(55)G1-1034 ) C
(3) Cosmetic Spec. : LCD Module IIS Spec.
Active area
5.1 Display Area
A
1) Active Display Area of the LCD Monitor Should be within Cabinet’s Bezel.
2) Distance Difference between Active Area and Bezel A A B
| A-B|<1.0 mm , | C-D|<1.0 mm
A: The Distance from The Left of Active Area to the Bezel Bezel
B: The Distance from The Right of Active Area to the Bezel
C: The Distance from The Top of Active Area to the Bezel
D: The Distance from The Bottom of Active Area to the Bezel D
Copyright © 2010 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 11 - LGE Internal Use Only
6. EDID
6.1 2
No Item Content 16진 Data
1 Manufacturer ID GSM 1E 6D
(Analog) 23222 (5AB6)
2 Product ID
(HDMI) 23224 (5AB8)
3 Year 2014
4 Version 1 01
Analog : 3
5 Revision 03
HDMI: 3
6 Serial Number * *
7 Week ** **
8 Model Name LG IPS FULLHD 4C 47 20 49 50 53 20 46 55 4C 48 44
9 Check Sum **** ****
10 Special Item Need to Input Serial Number

** Protocol : DDC 2AB


6.2 EDID Ver. 1.3 FOR ANALOG

6.4 EDID Ver. 1.3 FOR HDMI (256Byte)

Copyright © 2010 LG Electronics. Inc. All right reserved.


Only for training and service purposes
- 12- LGE Internal Use Only
TIMING CHART
(1) Signal(Video & Sync)

V id e o

B
C
S yn c

D E F
A

(2) H/V Timing

DOT Frequency Total Front Back


CLASSIF Polar Display Sync.
MODE CLOCK [kHz]/ Period Porch Porch Resolution
ICATION ity (A) (C)
[MHz] [Hz] (E) (D) (B)
H(Pixels) - 31.468 900 720 18 108 54
1 28.321 720 X 400
V(Lines) + 70.08 449 400 12 2 35
H(Pixels) - 31.469 800 640 16 96 48
2 25.175 640 x 480
V(Lines) - 59.94 525 480 10 2 33
H(Pixels) - 37.5 840 640 16 64 120
3 31.5 640 x 480
V(Lines) - 75 500 480 1 3 16
H(Pixels) + 37.879 1056 800 40 128 88
4 40.0 800 x 600
V(Lines) + 60.317 628 600 1 4 23
H(Pixels) + 46.875 1056 800 16 80 160
5 49.5 800 x 600
V(Lines) + 75.0 625 600 1 3 21
H(Pixels) - 48.363 1344 1024 24 136 160
6 65.0 1024 x 768
V(Lines) - 60.0 806 768 3 6 29
H(Pixels) + 60.023 1312 1024 16 96 176
7 78.75 1024 x 768
V(Lines) + 75.029 800 768 1 3 28
H(Pixels) + 108.0 67.500 1600 1152 64 128 256
8 1152 x 864
V(Lines) + 75.000 900 864 1 3 32
H(Pixels) + 63.981 1688 1280 48 112 248
9 108.0 1280 x 1024
V(Lines) + 60.02 1066 1024 1 3 38
H(Pixels) + 79.976 1688 1280 16 144 248
10 135.0 1280 x 1024
V(Lines) + 75.035 1066 1024 1 3 38
H(Pixels) - 65.290 2240 1680 104 176 280
11 146.25 1680 x 1050
V(Lines) + 59.954 1089 1050 3 6 30

H(Pixels) + 67.50 2200 1920 88 44 148


12 148.50 1920 x 1080
V(Lines) + 60 1125 1080 4 5 36

z D-SUB/DVI DTV Mode is not supported (interlace mode)

Copyright © 2010 LG Electronics. Inc. All right reserved.


Only for training and service purposes
- 13 - LGE Internal Use Only
Factory support Horizontal Vertical
mode frequency frequency HDMI
(Preset Mode) (KHz) (Hz)
1 480P 31.5 60 O
2 576P 31.25 50 O
3 720P 37.5 50 O
4 720P 45 60 O
5 1080i 28.12 50 O
6 1080i 33.75 60 O
7 1080P 56.25 50 O
O
8 1080P 67.5 60
(Recommend Mode)

Copyright © 2010 LG Electronics. Inc. All right reserved.


Only for training and service purposes
- 14 - LGE Internal Use Only
ADJUSTMENT

1. Coverage PC audio volume : MAX


Apply to 58.4 cm (23 inch) Wide monitor made in Monitor Factory * LAN cable
Gumi Korea) or made in accordance with the standard of Gumi * Router
Factory process. * PC: vSpace S/W for N+ ( Ver 4.5.xx.xx ) --- Caution: Ver
4.4.xx.xx for N1742L family

2. Appointment 3.2.2 Total Assembly Line


· Ready : Heat-run during5 minutes in the state with signal
2.1 Adjustment must be done as fixed sequence, and adjustment · Connect input signal to D-sub.
sequence can be modified after agreement withthe responsible · Default value before adjustment : Contrast “70” , Brightness
R&D engineer considering mass-production condition. ‘100(Max)”
2.2 Power : AC 100 - 240 Voltage (Free)
2.3 Input signal: 3.2.3 Adjustment of Horizontal/Verticality screen
2.3.1 RGB Input: As Product Standard (Signal ROM : LB800K position, Clock and Clock Phase at each Mode.
Ver1.6) · There is no special factory mode adjustment. Writing initial value
2.3.2 RJ-45 input : As Product Standard (Ethernet connection of EEPROM in Board Assembly line is adjusting Preset Mode
through network from Host PC) and Reset mode. (EEPROM is initialized when AC Power is
* PC spec for MK(Minikey) Loader (TBD): CPU - Dual core 2.0 ON first.)
GHzD, Memory - 2 GByteD · If the change of FOS data is needed after M.P, it is possible by
*PC spec for Host PC (TBD): CPU - Dual core 2.0 GHzD, writing Mode Data with EEPROM write command or modifying
Memory - 2 GByteD the Mode Data in MICOM itself.
2.4 Warm-up Time: Over than 30 minutes
2.5 Adjustment equipment : White balance equipment (CA-110), 3.2.4 Color coordinates adjustment and Luminance
Display adjust equipment, VG-813(or VG819), Oscilloscope, adjustment.
PC (More than 486 computer ) & White balance adjust 3.2.4.1 Color coordinates adjustment
program. · Monitor Contrast / Brightness
- Contrast : 70
- Brightness : 100(Max)
3. Adjustment · CA-110: Set “channel 9”
· Signal Generator : At cut-off and drive --> 16 step pattern for
3.1 Overview ADC (Program No.: 31)
Use factory automation equipment and adjust automatic - Output Voltage : 700 mVp-p
movement. But, do via passivity adjust in erroroccurrence. - Output Mode : Mode 12 (SXGA 60 Hz)mode Setting.

3.2 Adjustment order 3.2.4.2.Adjustment : Board Assembly Line


(refer to the Adjustment standard and adjustment command table) · Select RGB mode
· Input 16 step pattern for ADC (Program No.31 (Mode 12,Pattern
3.2.1 Board Assembly Line 11)). (Video level : 700 mVp-p)
3.2.1.1 15pin D-sub (RGB) · Adjust by commanding AUTO_COLOR_ADJUST
· Connect input signal to 15pin D-sub. · Confirm “Success” message in Screen or Check the data of
· Check the firmware version & model name. And write the 0xFE, 0xFF address of EEPROM(0XA6) is 0xAA after waiting 5
firmware code to the serial Flash ROM by ISP. seconds.
· Ready for adjustment : check whether adjustment command · If there is “FAULT” message or the data of 0xFE, 0XFF address
works normally or not and the operating state of each mode. of EEPROM(0xA6) is not 0xAA, do adjust again.
· Check the display state of gray color when 256 gray scale · If all Adjustment is completed, the values of 6500K, User Color
patterns is embodied. and 9300K are saved automatically.
· Read by EEPROM Read Command to check whether initial · Select RGB mode
value is correct or not. · Input 16 step pattern for ADC (Program No.31 (Mode 12,Pattern
3.2.1.2 MK( Minikey ) Loading 11)). (Video level : 700mVp-p)
· Open MK Loader Tool on MK Loader PC. · Adjust by commanding AUTO_COLOR_ADJUST
( * MK Loader PC should be connected Internet) · Confirm “Success” message in Screen or Check the data of
· Connect input signal to RJ-45 input with LAN cable connected 0xFE,0xFF address of EEPROM(0xA6) is 0xAA after waiting 5
network devices such as routers. seconds.
· Turn on the Monitor set.
· Click the box when the °∞empty port °∞box is changed to “write 3.2.4.3. Confirm at Total Assembly Line: adjustment
mini-key” in MK Loader Tool. · Check the data of 0xFE, 0xFF address of EEPROM(0xA6) is
0xAA.
3.2.1.2 RJ-45 input · If the data of 0XFE, FF address of EEPROM(0xA6) is not
· Connect input signal to RJ-45 input with LAN cable connected 0xAA, do adjust again by 3.2.4.2.
network devices such as routers.
· Check USB 1.1 Port (Keyboard/ Mouse) : @RJ-45 input
· Check USB 2.0 Port (USB Memory Stick 2port) : @RJ-45 input
· Check Audio (Ear-phone out/ Mic in/ Speaker) : @RJ-45 input,

Copyright © 2010 LG Electronics. Inc. All right reserved.


Only for training and service purposes
- 15 - LGE Internal Use Only
3.2.4.4. Confirm PRESET 6500K Color coordinates and Adjust when there is Process change or Adjustment setting change.
PRESET 9300K Color coordinates .
· Set as Aging mode ON, by commanding AGING_ON/OFF 3.2.5.5. OSD & Adjustment device Confirmation : Confirm
command code. operation mentioned as product spec.
· Select Module that is being used in present production by · Vary Brightness and Contrast and confirm the variation of
commanding MODULE SELECT. ( It is not needed so far. Luminance and display status.
However, it will be needed to apply other modules) · Operate the f-engine function and confirm variation of Luminance.
· Send SYSTEM RESET command to set Module data. · Make sure to do FACTORY RESET after confirmation of OSD
· Input Full White Pattern (Video level : 700 mVp-p) function.
· Set as 9300K by commanding COLOR_MODE_CHANGE
Command code. 3.2.5.6. Confirm the display state by inputting 8 color Bar Pattern &
· Check to meet x = 0.283 ± 0.03, y=0.298 ± 0.03, and confirm. 256 Gray Scale pattern.
· Only if it does not meet, adjust as below steps.
· Adjust to meet x = 0.283 ± 0.01, y=0.298 ± 0.01 in 5 minutes. and 3.2.5.7. DPM operation confirmation : Check if Power LED Color
confirm. and Power Consumption operates as standard.
· Save 9300K Color by commanding COLOR SAVE Command · Measurement Condition : 230 V@ 50 Hz (Analog)
code. · Confirm DPM operation at the state of screen without Video
· Set as 6500K by commanding COLOR_MODE_CHANGE Signal.
Command code.
· Check to meet x = 0.313 ± 0.03, y=0.329 ± 0.03, and confirm. 3.2.5.8. RJ-45 input
· Only if it does not meet, adjust as below steps. · Connect input signal to RJ-45 input with LAN cable connected
· Adjust to meet x = 0.313 ± 0.01, y =0.329 ± 0.01, and confirm. network devices such as routers.
· Save 6500K Color by commanding COLOR SAVE Command · Check USB 1.1 Port (Keyboard/ Mouse) : @RJ-45 input
code. · Check USB 2.0 Port (USB Memory Stick 2port) : @RJ-45 input
· Set as sRGB by commanding COLOR_MODE_CHANGE · Check Audio (Ear-phone out/Mic in/Speaker) : @RJ-45 input, PC
Command code. audio volume : MAX
· Adjust to meet Y = 150 ± 50, and confirm. * LAN cable
· Save sRGB Color by commanding COLOR SAVE Command * Router
code. * PC: vSpace S/W for N+ ( Ver 4.5.xx.xx ) --- Caution: Ver
3.2.4.5. Confirm User color coordinates . 4.4.xx.xx for N1742L family
· Confirm Whether User color is saved same as 6500K.
· After confirming Color coordinates, Must return to 6500K 3.2.5.9. DDC EDID Write
( Set as Aging mode ON, by commanding AGING_ON/OFF
3.2.5 Confirm Operation state. command code. )
3.2.5.1 Operation mode : Confirm whether each appointed mode 1) SUFFIX: xxxxxPN
operate correctly or not. · Connect analog Signal Cable to D-sub wafer.
3.2.5.2 Confirmation of Adjustment condition and operation : · Write EDID DATA to EEPROM(24C08) by using DDC2AB
Confirm whether it meet Auto/Manual equipment Adjustment protocol.
standard or not. · Check whether written EDID data is correct or not.
· Confirm Analog screen state : Confirm screen state at below (refer to Product spec).
mode. --> After writing EDID, send Elapsed Time Clear command.
Appointment mode (RGB input): (Elapsed time should not be displayed, after EDID writing)
640*480 @60Hz (Mode 1), : Confirm periodically (in the first set of new lot, process change)
800*600@75Hz(Mode 5), whether module name and aging time disappeared on the self-
1024*768@60Hz(Mode 8), diagnostics OSD with signal cable disconnected.
1280*1024@60Hz(Mode 12), --> If Elapsed Time Clear command isn°Øt executed, module
SMPTE pattern(Check 0%,5%,95%,100%) name, aging time and TCO word appear on the self-diagnostics
–Mode can be added. OSD.(Module name and aging time should not appear after
writing EDID)
3.2.5.3. Confirm Auto adjustment operation. --> Make sure to do FACTORY RESET at the final process.
· Input Analog 1 Dot on/off & Rectangle Pattern at Mode
12(1280x1024@60 Hz) 3.2.5.10. Shipping condition
· Confirm adjustment operation by changing Clock, Phase, H/V · Contrast : 70
Position. · Power Switch : Off
· Check Clock, Phase by pressing AUTO Key. · Brightness : “100(Max)”
· Confirm first set of new lot by periods · Color Select : Preset ( 6500K )
· Language Select : Refer to product spec.
3.2.5.4 Other quality · OSD Position : Center
· Confirm that each items satisfy under standard condition that was · Power indicator : ON
written product spec. · Flatron f-engine : Normal
· Confirm Applying Module & MICOM Setting --> Confirm with
Service OSD
- Confirm at Service OSD by “Menu + Power key” on .(from
Power off)
- Confirm first set of new lot by periods, and confirm periodically
Copyright © 2010 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 16 - LGE Internal Use Only
4.Standard of Auto/Manual equipment adjustment

No Item Adjustment & measurement Operation Operation Measurement


. standard mode Pattern Position
1 Voltage(V) 12 V ± 0.6 V MODE 13 Pattern4
TP of
5V± 0.3V / 3.3V± 0.25V
Each power
2.5V± 0.2V
2 Color Black Auto Adjustment MODE 12 Pattern 0
Level Center
coordinates
of Screen
(9300/6500K)
3 Color DRIVE1 MODE 12 Pattern1
coordinates u uí= 0.198 ± 0.00 5
(6500K) v ví=0.468± 0.005 Center
Color DRIVE2 of Screen
X 0.283± 0.004
coordinates
Y 0.298± 0.004
(9300K)

Luminance 6500K More than MODE 12 Pattern1


Center
220 cd/m2 (700 mVp-p)
of Screen

4 Screen H MODE
FULL SIZE Pattern4 Full Screen
Position V 1 - 13

5 Screen CLOCK FULL SIZE MODE Pattern 4


Full screen
Compensation PHASE 12-13
AUTO FULL SIZE MODE Pattern 4
Full screen
12-13
6 DPM Normal Mode 40 W(Typ) MODE 12 Pattern 4 Blue
Confirmation Stand By Mode 1W/ - Pattern 6 Flicker
(RGB/LAN) Suspend Mode 1W/ - Pattern 7 Flicker
DPMS Off 1W/15W Pattern 8 Flicker
Power Switch 1W
off
Off
7
Gray scale Confirmation Linear gray Scale MODE 12 Pattern 9 Full screen

8 Withstanding Voltage When 1500Vac or 2121Vdc is


confirmation impressed between the first of
power (Live/Neutral) and
ground (Earth) for 1 second,
check whether something
wrong happens or not.
When 25A is impressed
nd
between Earth and 2 Ground
9 Ground Confirmation
for 1 second, Resistance must
be less than 0.1
16 step pattern for ADC
10 Cutoff /ADC Adjustment Pattern MODE 12 Pattern11
1280*1024@60Hz (700mVp-p)
CPU : Dual core 2.0 GHz ,
Memory : 2 GByte ,
11 Network Test with PC 1280 * 1024
Teradiciís PCoIP Host Card
LAN cable

*Check items No. 2, 3, 4, 5 and 7 at RGB input.

Copyright © 2010 LG Electronics. Inc. All right reserved.


Only for training and service purposes
- 17 - LGE Internal Use Only
5. Pattern for Adjustment
Pattern 0 : FULL BLACK (State of without video signal )
Pattern 1 : FULL WHITE (Don’t display other Character except for White Pattern)
Pattern 3 : FULL WHITE
Pattern 4 : Cross hatch pattern (Horizontal 10Line, Vertcial 8Line) & Rectangle Pattern
Pattern 5 : 1 Dot on, 1 Dot off & Rectangle Pattern
Pattern 6 : Vertical Sync only input (Use signal cable of which Pin #5 is GND)
Pattern 7 : Horizontal Sync only input (Use signal cable of which Pin #5 is GND)
Pattern 8 : State of without Vertical/Horizontal Sync and Video Signal. (Use signal cable of which Pin #5 is GND)
Pattern 9 : 8 Color Bar Pattern + 16 Gray Level Pattern
Pattern 10 : SMPTE Pattern
Pattern 11 : 16 Gray Step Pattern (700mV)

Copyright © 2010 LG Electronics. Inc. All right reserved.


Only for training and service purposes
- 18 - LGE Internal Use Only
BLOCK DIAGRAM (Main)

Copyright © 2010 LG Electronics. Inc. All right reserved.


Only for training and service purposes
- 19 - LGE Internal Use Only
No power issue

Check JK100 PIN NO CHECK ADAPTER


1

Only for training and service purposes


YES
Is IC102 NO
PIN2(19V),PIN3( CHECK IC102
5V)

Copyright © 2010 LG Electronics. Inc. All right reserved.


YES
Is IC 201 NO
PIN1(3.3V), CHECK IC201
PIN3(1.2V)
YES

- 20 -
Is IC100 NO
1. NO POWER

PIN45,PIN46 `
CHECK CRYSTAL X100
PULSE

CHECK IC100
TROUBLESHOOTING GUIDE

IC102-#1 IC102-#2 IC201 X100

LGE Internal Use Only


No Raster(OSD is not displayed)

Only for training and service purposes


Check IC100 NO CHECK IC 201 PIN2(3.3V)
PIN4(3.3V)

Copyright © 2010 LG Electronics. Inc. All right reserved.


YES
1.CHECK X100
IC100 PIN45,46 NO 2. Trouble in IC100
14.318MHz

YES

- 21 -
CHECK IC100
PIN39(H- NO CHECK IC100
SYNC),PIN40(V-
SYNC)

YES
Is IC100 PIN43 NO CHECK CONNECTION From DSUB
PULSE TO IC100
2. NO RASTER (OSD IS NOT DISPLAYED) – MAIN

Trouble in cable or LCD module

LGE Internal Use Only


3. TROUBLE IN DPM

CHECK PC. PC is going to the DPM

CHECK H/V SYNC LINE


mode

NO
NO
Check R135 AND R137

YES

YES
IC100 PIN41,42
Trouble in DPM

Trouble in IC100

Copyright © 2010 LG Electronics. Inc. All right reserved.


Only for training and service purposes
- 22 - LGE Internal Use Only
EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts
are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as recommended
in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

920

910
900
400

550

830
820

or
500

810

540
330
200

LV1
300
PCB P/N: EAX65543110_1.0 (LM14B) LED DRIVE FB LED DRIVE CH

FB4

FB3

FB2

FB1
L103 D107
33UH BR210

Date : 2014.08.14
5VS 19V_LED

READY
215 PANEL BIZ 100V READY
C151

R188
100K
215 PANEL BIZ
R245 R246 1uF
0 0 50V

R183
150K

1%
No bead C154 C222
L106-*1 33uF 33uF
0 7
100V 100V

R153

READY
D READY
C152

R189
100K
FB1

1K
1/8W R165 Q106 1uF JP129
6
5% 10 AOD478 50V

1/16W
Q101 D Q102 D Q103 D Q104 D G
DRV

R158
1.2VS

1/16W

1/16W
R156

R157

R184
150K
1/16W

1%
S FB2

1M

1%
R155
G G G G JP130 5

1M

1%

1M

1%
1M

1%

R160
47K
READY
S S 2N7002K S 2N7002K S

R197
4.7K
C143 2N7002K 2N7002K 4
1uF
C119 C121 C123 JP128
10V
0.1uF 0.1uF 0.1uF
16V 16V 16V 3

KEY_SCL/KEY0_ADC

KEY_SDA/KEY1_ADC
3.3VS 3.3VS_MAIN R161
L106 200 FB3 JP131
UBW2012-121F SENP 2

VDT2

VFB1

VDT1
C117 C118 C120 C122 C124 C125 FB4

VFB4

VFB3

VDT3

VFB2

R159
JP132 1

VDT4
power line bead C126 C127 C129

100

1
C116 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF

LED_INDICATOR
0.1uF 16V 16V 16V 16V 16V 16V 0.1uF 0.1uF

R164

R166

R167

R168

R169

R172

R175

R178

R179

R180
16V 16V 16V

HDMI_DET
16V
12507WR-06L
P102
130724
ESD protection GND
56->1K
5VS

VFB4

VDT4

VFB3

VDT3

VFB2

VDT2

VFB1

VDT1

SENP

DRV
GND
Multi Option Touch control OVP
3.3VS_MAIN

R128-*1

R130-*1

R130

R132
R128
1.2VS
Check!! Control wafer,LED Color

56
R138 Close to Scaler

56

1K
1K
Tact Control OVP
5VS 3.3VS_MAIN

PB2/INTE1/ADC2

PE1/LPDIN0/VSO
C140 S/W Control

PA2/ADC6/CEC0

DVDD/LED_3.3V
1uF C144

R154
8.2K
R150

1%
PC4/IR1/PWMC
1K 10V 100pF
READY
5VS

MVDD_3.3V_2

CVDD_1.2V_2
one reflow with Top-mask 50V

ADUC 20S 02 010L


R331 Control PWR 5V Control PWR 3.3V 1/16W
P100 180 5%

1/10W

1/10W

1/10W

1/10W
R106 R109

R143

R145

R147

R149
SMAW200-06 R194

5.1

5.1

5.1

5.1

VA104 20V
PB3/ADC3
PE2/PWMC
0 0 10

5%

5%

5%

5%
P30/RXD
P31/TXD
L100
BLM18PG121SN1D
1 10V

ISEN4

VDET4
ISEN3

VDET3
ISEN2

VDET2
ISEN1

VDET1
4.7uF
JP104

[EP]

DGND

VFB4

VFB3

VFB2

VFB1

SENP
SENN
COMP

5VCC
C142

PC2

OVP

DRV
2 JP133

FB
3.3VS_MAIN

3
JP100
C105
0.1uF
R104
4.7K
R105
4.7K
1.2VS LVDS OUT
16V

128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
MMBT3904-(F)
Q100 31
4 C R112 D105
JP103 L202 PA4/INTE2 BOOT BAT54 30
BLM18PG121SN1D B 4.7K
HDMI_HPD 1 96 Y0M-B JP123
5 C110 LED_INDICATOR
ADUC 20S 02 010L

KEY_SCL/KEY0_ADC 0.1uF PA7/SDA3/TXD3 LVDS_3.3V 30V Y0P-B 29


ADUC 20S 02 010L

ADUC 20S 02 010L

ADUC 20S 02 010L

JP107
JP101 R110 R120 2 95 C145
POWER AUTO INPUT READY16V E HDMI_SDA THERMAL 1uF Y1M-B 28
56 JP108
6 KEY_SDA/KEY1_ADC
4.7K
HDMI model only PA6/SCL3/RXD3 3 129 94 T0M 10V
27
JP102 Y0M-B Y1P-B JP109
20V

20V

20V

20V

L203 R119
BLM18PG121SN1D MENU SES EXIT HDMI_SCL TVCC T0P 26
C106 C108 56 4 93 Y2M-B JP110
0.1uF 0.1uF
Y0P-B
HDMI model only 25
16V 16V RX1C- T1M Y2P-B JP111
Tact control Tact control 5 NC 92 Y1M-B 24
Multi Option Touch control
RX1C+ 6 91 T1P
VA100

VA103

VA101

VA102
READY

READY

NC Y1P-B CLKOUTM-B JP112


23

C106-*1 C108-*1 RX10- 7 NC 90 T2M CLKOUTP-B JP113


22
130724 68pF 68pF Y2M-B
50V 21
50V
RX10+ T2P Y3M-B JP114
READY->APPLY Touch control
Touch control 8 NC 89 Y2P-B
Y3P-B JP115 20
RX11- 9 NC 88 TCLK1M 19
CLKOUTM-B Y0M-A JP116
RX11+ 10NC 87 TCLK1P Y0P-A JP117
18
CLKOUTP-B
17
RX12-
RX12+
11NC
12NC
IC100 86 T3M
T3P
Y3M-B
Y1M-A JP118
16

85 Y3P-B Y1P-A JP119


15

PA0/ADC4 T4M 14

Multi Option for APW7313(DC/DC)


PA1/ADC5
13
14
NT68773 84
83 T4P
Y0M-A

Y0P-A
Y2M-A JP120
13

12
Y2P-A JP121
PC3 15 82 T5M 11
APW7313 When apply LGD panel ,With ITLC pin : Y1M-A CLKOUTM-A JP124
IC102-*1
APW7313KAITRG[EP]GND
C111-*1 C115-*1 L102-*1
10uH
R103-*1
100 Interlace mode :use R238 & R240 PA5/INTE3 16 81 T5P CLKOUTP-A JP122 10
0.01uF 0.1uF
Normal mode: use R239
Y1P-A
25V 16V Y3M-A
BS
1 8
SS
APW7313 APW7313 APW7313 1/10W Other panel :keep R238 R239 R240 Ready PB7/SDA1/TXD1 17 80 T6M JP125 9
THERMAL

APW7313 Y2M-A
VIN EN

Need to change Y3P-A


9

2 7
JP126 8
LX
3 6
COMP
C114-*1 PanelOPT(ITLC)
PB6/SCL1/RXD1 18 79 T6P
R108-*1 R101-*1 R102-*1 Y2P-A 130722 7
3300pF 68K
GND
4 5
FB
8.2K
APW7313
50V
APW7313 APW7313
15K
APW7313 ITLC
R238
100 PanelOPT(ITLC)
R240 R123
PE3/CEC1 19 NT68771H OD 78 TCLK2M
CLKOUTM-A
Improve Inrush
Q108,R151,R152 APPLY
R177 1K->2.7K
5VS VCOM-SCL JP134 6

1/16W
REXT TCLK2P VCOM-SDA JP135 5
5%
4.7K

1/16W
5%
470

1/16W
RX2C-
20 NT68770H Non-OD 77
T7M
CLKOUTP-A
C147 1uF->4.7uF

ITLC
R329
JP136 4

HDMI_RXC-
5% 21 76 Y3M-A 0 3
READY READY ZXMP3F30FHTA
RX2C+ 22 75 T7P R151
Q108 Q107
PanelOPT(Non-ITLC) 1/16W
2
HDMI_RXC+ Y3P-A MMBT3904(NXP) 5%
1K JP127

D
RX20- 23 74 LVDS_GND/DGND C
1
HDMI_RX0- C150 C153
R176 C147 1uF R191
RX20+ SPI_CLK B 1000pF

G
24 73 4.7uF 10V
READY 22K
HDMI_RX0+ SPI_CLK 10V 1K

one reflow with Top-mask 19V to 5V DC/DC HDMI_RX1-


RX21- 25 72 SPI_SI 3.3VS_MAIN
E
R152
0
50V 10031HR-30

C149
SPI_DI P101

10V
1uF
1/16W R177
JK100
DS-262HBR
RX21+ 26 71 SPI_SO 5% 2.7K
For two channel Module
HDMI_RX1+ SPI_DO
4 SHIELD_1 19V_LED RX22- 27 70 SPI_CE C
HDMI_RX2- SPI_/CS MODON

4.7K

R115
B Q105

4.7K

R116
RX22+ 28 69 PE0/PWMA/DBC MMBT3904(NXP)

5%
JP106 R163

5%
3 FIX HDMI_RX2+ WP_Flash
4.7K E
1.2VS
TGND 29 68 P34 33
R107
2 SW 100K VCOM-SDA R171
ADC_3.3V/TVCC P35/LPD_OUT R117 4.7K
4.7uF
4.7uF

4.7uF

33
30 67 5%
25V
25V

25V

L101 READY
UBW2012-121F IC102 VCOM-SCL
R118
1 VIN
TPS54339EDDAR[EP]GND ADC_1.2V 31 66 PC0/PWMB 5%

4.7uF 4.7uF MODON


JP105 25V 25V AGND 32 65 PC6/MUTE/PWMB
C217

VBST SS
C218
C216
C158
C103

1 8
C107
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
THERMAL

68uF
35V
105C Close to IC VIN EN TPS5433
V-com:R115,R116,R117,R118(Ready)
9

2 7 C115
TPS5433 8200pF
5VS D205 C109 C170 TPS5433 25V
0.047uF BIN+

0.047uF BIN-

0.047uF GIN+

0.047uF GIN-

0.047uF RIN+

0.047uFRIN-

HSYNCI
VSYNCI/TOUTP
R139 56PB5/SDA0/TXD0

R140 56PB4/SCL0/RXD0
PC5/IR2/PWMD
OSC_VDD
OSCO
OSCI
OSC_GND/DGND
PB0/INTE0/ADC0
PB1/ADC1
PA3/PWMD
NC
MVDD_3.3V_1
DVDD
RSTB
CVDD_1.2V_1
PC7/IR3/SPDIF
AUDIO_VDD
AUDIO_CEXT1
WD/AIN_R
I2S0/AIN_L
SCK/AOUT_R
MCLK/AOUT_L
AUDIO_VP
AUDIO_GND
SW VREG5
30V 4.7uF
25V
0.1uF
25V
C111
0.1uF
3 6
Only used for LGD Panelbiz model
TPS5433
R108

16V GND VFB


0

4
3A 5
25V
25V
25V

25V
25V
25V

TPS5433
L102
4.7uH

Large thermal PAD on bottom side


C146
TPS5433 15pF
R126 56C128

R127 100C130
R129 56C131

R131 100C132

R133 56 C133

R134 100C134

R101 50V C114 5VS


R135 56

R137 56

100K TPS5433 0.47uF READY C139


C100 C101 1% R103
16V 1M 10uF
10uF 10uF TPS5433 10V
0
10V 10V 5VS R142 1.2VS
1/10W
4M Serial Flash
R141

R195
4.7K
TPS5433 TPS5433
1K

C
R102
18K R124 14.31818MHz B Q109
1% 4.7K X100 MMBT3904(NXP) 3.3VS_MAIN
R125 50V 50V

R196
HEAD_LOUT
3.3VS_MAIN 10V

HEAD_ROUT
4.7K E

20K
22pF 22pF
C135 C136 4.7uF
C160
R148

R170

C138
10K

READY
IC101

R182
4.7K
WP_24C02

0.1uF
RED

W25X40CLSNIG
BLUE

GREEN

4.7K

16V
For Non-OD model
DSUB_SCL

10V
DSUB_SDA

DSUB_DET
HSYNC

VSYNC

C157
4.7uF R100
C141 33
0.1uF
CS VCC
SPI_/CS 1 8 16V
IC103
3.3VS R173
AZ1117H-3.3
L105 33 DO[IO1] HOLD R190 10K
BLM18PG121SN1D SPI_DO 2 7
INPUT 3
1A 1
2 OUTPUT

WP_Flash
R174
33 WP
3 6
CLK
R192
33
READY SPI_CLK
ZD100 D207 ADJ/GND
5.6B R193

R181
4.7K
5.6V Large thermal PAD on bottom side GND DI[IO0] 33
C113 C112 4 5
130724 4.7uF 0.1uF D206 SPI_DI
Main IC EOS protection 10V 16V 5.6V
C156
Ready 22pF
50V
READY

3.3VS

D208
KDS184
A2
C IC201
A1 APE8839AMP-C [EP]GND C221
4.7uF
10V
D209 VOUT1 EN1
1 8
KDS184
THERMAL

A2
C VIN1 GND_1
9

2 7
A1

VOUT2 GND_2
1.2VS
one reflow with Top-mask 3 6
R330
ADUC 5S 02 0R5L

6.8
VIN2 EN2
2W 4 5
Ready

C219
VA219

10V
1uF
HTC TJ5631

C220
4.7uF
10V

For OD model

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES


SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MP35,45,55,56,65
DSUB + HDMI 2013-10-24
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. SCALER 1 2
one reflow with Top-mask

JK202

ADLC 5S 02 015

ADLC 5S 02 015

ADLC 5S 02 015
DSB47C-15BS1YN32
DSUB INPUT

5.5V

5.5V

5.5V

75
75

75
VA200

VA201

VA202

R205
R203

R204
RED_GND
6 GNDR
GND_2
1 11 RED
RED
GREEN_GND
7 JP204
GNDG
DDC_DATA
2 12 DSUB_SDA
GREEN
GREEN
BLUE_GND
8 GNDB
H_SYNC
3 13 HSYNC
BLUE
BLUE
9 NC
V_SYNC
4 14 VSYNC
GND_1

10 SYNC_GND
JP205
DDC_CLOCK
ADUC 20S 02 010L

ADUC 20S 02 010L

ADUC 20S 02 010L

ADUC 20S 02 010L

ADUC 20S 02 010L


5 15 DSUB_SCL
DDC_GND
DSUB_DET

C203 68pF

C205 68pF
3.3VS_MAIN

C202 68pF

C204 68pF
20V

20V

20V

20V

20V
R215
16 10K

R209 4.7K
R210 4.7K
SHILED 50V 50V 50V 50V
VA203

VA204

VA205

VA206

VA207

HDMI INPUT
3.3VS_MAIN

Ear-phone OUT
R200
10K
one reflow with Top-mask

C209
10uF
HDMI_DET L200

10V
one reflow with Top-mask JP206 JP207 BLM18PG121SN1D HEAD_LOUT

ADUC 20S 02 010L


R229
HDMI_HPD SHIELD_PLATE

20V
5.1
VA218 R202 R217
BODY_SHIELD 20V HDMI_5V 10K 1K
READY
20

VA214
R201 1K
T_SPRING
19 C200
HOT_PLUG_DETECT 1/10W 0.1uF
VA217 16V
18 R_SPRING

C211
10uF
VDD[+5V] 20V L201

10V
17 READY BLM18PG121SN1D HEAD_ROUT
DDC/CEC_GND JP208
16
HDMI_SDA
SDA JP201 D200 D201 R230

ADUC 20S 02 010L


HDMI_SCL BAT54C BAT54C

20V
15 A2 A2 5.1
SCL VA215 VA216 HDMI_5V
JP200
20V 20V
C201
C C
E_SPRING
14 JK201 R218
RESERVED READY READY 0.1uF A1 A1
13 16V 5VS PJ-3517HAR-3-BL 1K
IC200

VA212
CEC (OPT)ESD_HDMI_SEMTECH
12 D203 M24C02-RMN6T
TMDS_CLK- RCLAMP0524PA
R213
4.7K

R214

4.7K

R216
4.7K

1 10
11
TMDS_CLK_SHIELD
HDMI_RXC- E0 VCC
2 9 1 8
10
HDMI_RXC+
3 8 one reflow with Top-mask
TMDS_CLK+
9
4 7
HDMI_RX0- E1 WC WP_24C02
TMDS_DATA0- 5 6 2 7
8
HDMI_RX0+
TMDS_DATA0_SHIELD
E2 SCL 200 HDMI_SCL M1
7 3 6 R211
TMDS_DATA0+ MAZ64683701
6
TMDS_DATA1- VSS 4 5 SDA R212 200 HDMI_SDA
5 (OPT)ESD_HDMI_SEMTECH
TMDS_DATA1_SHIELD
4 33 ohm => 200 ohm for surge reduction
TMDS_DATA1+ D204
RCLAMP0524PA
3 1 10
TMDS_DATA2- HDMI_RX1-
2 9
2
TMDS_DATA2_SHIELD
HDMI_RX1+ ESD_HDMI_NXP ESD_HDMI_NXP
130620
3 8 D203-*1 D204-*1 JIG GND Point addition
IP4283CZ10-TBA IP4283CZ10-TBA
1 4 7
TMDS_DATA2+ HDMI_RX2- TMDS_CH1-
1 10 NC_4
TMDS_CH1- 1
10 NC_4

5 6 TMDS_CH1+
9 NC_3
TMDS_CH1+ 2
9 NC_3
HDMI_RX2+ GND_1
2

3 8 GND_2
GND_1 3
8 GND_2
TMDS_CH2-
4 7 NC_2 TMDS_CH2- 4 7 NC_2
HDM2LB-19BG2RL1L Shield TMDS_CH2+
5 6 NC_1
TMDS_CH2+ 5
6 NC_1

JK200
JP_GND1 JP_GND2 JP_GND3 JP_GND4

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES


SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MP35,45,55,56,65
DSUB + HDMI 2013-10-24
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. Interface 2 2

S-ar putea să vă placă și