Documente Academic
Documente Profesional
Documente Cultură
У ч е б н о е п о с об и е
(версия 12)
Получение
изометрических
чертежей
Модуль М13
www.aveva.ru
www.aveva.ru
Получение изометрических чертежей
Учебное руководство (Модуль M13)
Revision Log
Date Revision Description of Revision Author Reviewed Approved
04/05/2010 1.0 VR
Updates
All headings containing updated or new material will be highlighted.
Suggestion / Problems
If you have a suggestion about this manual or the system to which it refers please report it to the AVEVA
Group Solutions Centre at gsc@aveva.com
This manual provides documentation relating to products to which you may not have access or which may
not be licensed to you. For further information on which products are licensed to you please refer to your
licence conditions.
Disclaimer
Information of a technical nature, and particulars of the product and its use, is given by AVEVA Solutions Ltd
and its subsidiaries without warranty. AVEVA Solutions Ltd. and its subsidiaries disclaim any and all
warranties and conditions, expressed or implied, to the fullest extent permitted by law.
Neither the author nor AVEVA Solutions Ltd or any of its subsidiaries shall be liable to any person or entity
for any actions, claims, loss or damage arising from the use or possession of any information, particulars or
errors in this publication, or any incorrect use of the product, whatsoever.
Trademarks
AVEVA and Tribon are registered trademarks of AVEVA Solutions Ltd or its subsidiaries. Unauthorised use
of the AVEVA or Tribon trademarks is strictly forbidden.
AVEVA product names are trademarks or registered trademarks of AVEVA Solutions Ltd or its subsidiaries,
registered in the UK, Europe and other countries (worldwide).
The copyright, trademark rights or other intellectual property rights in any other product, its name or logo
belongs to its respective owner.
www.aveva.com
2
Получение изометрических чертежей
Учебное руководство (Модуль M13)
Copyright
Copyright and all other intellectual property rights in this manual and the associated software, and every part
of it (including source code, object code, any data contained in it, the manual and any other documentation
supplied with it) belongs to AVEVA Solutions Ltd. or its subsidiaries.
All other rights are reserved to AVEVA Solutions Ltd and its subsidiaries. The information contained in this
document is commercially sensitive, and shall not be copied, reproduced, stored in a retrieval system, or
transmitted without the prior written permission of AVEVA Solutions Limited. Where such permission is
granted, it expressly requires that this Disclaimer and Copyright notice is prominently displayed at the
beginning of every copy that is made.
The manual and associated documentation may not be adapted, reproduced, or copied in any material or
electronic form without the prior written permission of AVEVA Solutions Ltd. The user may also not reverse
engineer, decompile, copy or adapt the associated software. Neither the whole nor part of the product
described in this publication may be incorporated into any third-party software, product, machine or system
without the prior written permission of AVEVA Solutions Limited or save as permitted by law. Any such
unauthorised action is strictly prohibited and may give rise to civil liabilities and criminal prosecution.
The AVEVA products described in this guide are to be installed and operated strictly in accordance with the
terms and conditions of the respective licence agreements, and in accordance with the relevant User
Documentation. Unauthorised or unlicensed use of the product is strictly prohibited.
www.aveva.com
3
Содержание
1 Введение .................................................................................................................................................. 5
1.1 Рассматриваемые темы ............................................................................................................... 5
1.2 Условные обозначения ................................................................................................................. 5
2 Изометрические чертежи ...................................................................................................................... 6
2.1 Запуск модуля Isodraft .................................................................................................................. 6
2.2 Текущий элемент – CE ................................................................................................................... 9
2.3 Пакетная обработка (Detail) .......................................................................................................... 9
2.4 Изменение типа получаемых изометрических чертежей – Produce .................................... 9
2.5 Option Files – файлы для настроек изометрического стандарта ....................................... 10
Упражнение ................................................................................................................................................... 10
www.aveva.com
4
Глава 1
1 Введение
Целью данного учебного курса является изучение возможностей получения изометрических чертежей
в среде AVEVA PDMS.
Дополнительная информация
Обратите внимание!
www.aveva.com
5
Глава 2
2 Изометрические чертежи
Изучение настроек изометрических чертежей другого вида, например Check или Stress в данном курсе
не рассматривается. Здесь будет рассмотрено получение простого изометрического чертежа,
построенного по шаблон, включенного в установку данной системы.
Перед тем как начать работу по получению изометрических чертежей, необходимо убедиться, что
созданный трубопровод, или его ветвь не имеют никаких внутренних ошибок, таких как потеря
взаимосвязи со спецификацией (неверная ссылка SPREF), элементы могут быть не связаны между
собой, или же пересекаются друг с другом. Для выполнения данной операции необходимо
воспользоваться командой меню Utilities:
Utilities > Data Consistency…
В результате данной операции получаем отчет, итогом которого должна являться фраза: «No data
inconsistencies» (трубопровод не содержит никаких внутренних ошибок).
После получения положительного результата проверки трубопровода можно переходить к получению
изометрических чертежей.
Для этого мы запускаем модуль Isodraft, непосредственно из модуля Design.? Воспользовавшись меню
Design:
Design > Modules > Isodrfaft > Macro Files…
www.aveva.com
6
Получение изометрических чертежей
Учебное руководство (Модуль M13)
При входе в данный модуль на экране монитора появляется форма Isodraft members, содержащая в
себе список элементов базы данных Design.
Текущий элемент иерархии базы проекта, относительно которого будет получен изометрический
чертеж, отображен в позиции CE. В списке файлов настроек присутствуют четыре option-файла: два
для метрических единиц измерения, два - для британских. Выберем файл с именем Basic.met.
Нажатие на кнопку Apply сгенерирует изометрический чертеж, согласно настройкам, указанным в
Basic.met, и выведет его в графическую область данного модуля.
www.aveva.com
8
Получение изометрических чертежей
Учебное руководство (Модуль M13)
При выборе команды Isometrics > Standard выбранный элемент иерархии становится текущим (CE).
Для назначения другого элемента текущим (CE), необходимо выбрать его в дереве иерархии и нажать
кнопку СЕ на форме Standard Isometric. Данная операция позволит обновить форму Standard Isometric,
а также получить изометрический чертеж для нового текущего элемента.
Для изменения типа файлов которые будут получены после генерации необходимо в поле Produce
выбрать следующее:
Тransfer files – для передачи полученных изометрических чертежей в другую систему.
Batch marco – получение макроса для производства изометрических чертежей в пакетном режиме
(обычно данная операция производится при большом количестве файлов в ночное (нерабочее)
время)
Bolt Report – получение отчета по шпилечным и болтовым соединениям.
www.aveva.com
9
Получение изометрических чертежей
Учебное руководство (Модуль M13)
Упражнение
www.aveva.com
10