Documente Academic
Documente Profesional
Documente Cultură
Drawer Slides
Side Mounting Drawer Slides
Design Reg. No: 159024/87
Special Features
! New smooth, silent roller system.
! Right side pair has lateral guiding.
! Left side pair has side gap adjustment.
! Tilt and remove of drawer.
! Stopper to prevent drawer from falling.
! New “Auto-Closing” feature of drawer.
! “System 32” compatible.
! Ribs provided for strength.
! Load capability - 20 kgs.
37.00
2.00 17.25
9.0
250 2.0
300
350
13.20
375
400
450
500
525
550
600
9.00
37.00 128.00 96.00 96.00 96.00 96.00
Front Edge
of Cabinet
650
700
750
31.50 128.00 128.00 128.00 128.00 128.00
6
Specifications
7.0
SMDS 37 375 285
Clearance
25.4mm
Top
* SMDS 70 700 610
1"
(5/8”)
12.7 12.7
1/2" 1/2"
WOODEN
DRAWER
STEEL STEEL
DRAWER CABINET
7
Bottom Mounting Drawer Slides
12.5
! Ribs provided for strength.
! Load capability - 20 Kgs.
7.0
14.5
37.00
17.25
9.0
2.0
2.00
13.20
250
300
350
375
400
450
500
525
550
600
9.00
Front Edge 37.00 128.00 96.00 96.00 96.00 96.00
of Cabinet
8
Specifications
CABINET
Fitting Instructions
Clearance
1. Side gap of 12.7 mm (1/2”) per side required (Refer fig. 1).
25.4mm
1"
Top
2. 25.4 mm (1”) clearance from top edge of drawer required
to tilt and remove drawer (Refer fig. 2).
3. Fixed and moving slide should be equally offset by 2 mm
for Auto-Closing (Refer fig. 2). DRAWER 2.0
4. Recess screw heads to avoid interference.
5. A set of slides must be fitted parallel and at same heights
to each other. FIXED SLIDE
MOVING SLIDE
Caution 2.0
12.7 12.7
1/2’’ 1/2’’
WOODEN
DRAWER STEEL
DRAWER
STEEL STEEL
6.0 CABINET CABINET
6.0
9
Full Panel Drawer Slides
Special Features
! Simplifies construction of drawer as it eliminates the sides of ! Precision rollers for smooth running.
drawer. ! Load capability - 25 kgs.
! Saves wood, labour, drawer space, time and cost, which ! "System 32'' compatible.
enhances bulk production. ! Stopper prevents drawer from falling.
! Tilt and remove capability with guiding. ! Also available with 6 mm bottom track easy to fit and helps in faster
! Auto closing of drawer. assembly, as it does not require screwing the bottom, using 6 mm board in
! Front facia adjustment. place of 9 mm or 12 mm.
! Ribbed for strength.
2.00
300
350
375
400
450
500
525
550
600
Specifications
10
12
FULLPANEL BOTTOM TRACK
FPDS 54 30-6 FPDS 86 30-6 FPDS 125 30-6 FPDS 150 30-6 300 225
FPDS 54 35-6 FPDS 86 35-6 FPDS 125 35-6 FPDS 150 35-6 350 275
FPDS 54 37-6 FPDS 86 37-6 FPDS 125 37-6 FPDS 150 37-6 375 300 Powder
Coated
FPDS 54 40-6 FPDS 86 40-6 FPDS 125 40-6 FPDS 150 40-6 400 325
Black,
Brown
FPDS 54 45-6 FPDS 86 45-6 FPDS 125 45-6 FPDS 150 45-6 450 375
and
Ivory.
FPDS 54 50-6 FPDS 86 50-6 FPDS 125 50-6 FPDS 150 50-6 500 425
FPDS 54 52-6 FPDS 86 52-6 FPDS 125 52-6 FPDS 150 52-6 525 450
FPDS 54 55-6 FPDS 86 55-6 FPDS 125 55-6 FPDS 150 55-6 550 475
FOUR HEIGHTS
150mm
125mm
86mm
54mm
Wooden Shelf
Full Panel with 6mm Bottom Track
A B C D 15.5
(mm) (mm) (mm) (mm)
54 71 52 32
86 103 84 64
B
A
D
C
8.5
1.3
3. Fixed slide should be set by 2mm for auto-closing. (Refer fig 2).
4. Screws should be recessed to avoid fouling. CABINET
5. Fixed slides should be fitted parallel and at equal height to each other.
6. Front fascia is to be fitted into front brackets which have 2-way Fixed Slide
adjustment for alignment. 2 mm
11
Full Panel Drawer Slides 250
Special Features
! Simplifies construction of drawer as it eliminates the sides of drawer.
! Saves Wood, Labour and Drawer space.
! Tilt & remove capacity with guiding.
! 'Auto-Closing' of drawer.
! Front facia adjustment.
! Ribbed fro strength.
! Precision rollers for smooth running.
! 25 Kgs. load capability.
! 'System 32' Compatible. 15.5
! Stopper prevents Drawer from falling.
! Available with 6 mm bottom track is easy to fit and helps in faster
assembly, as it does not require screwing the bottom, using 6 mm board in
place of 9 mm or 12 mm.
64.0
Fitting Instructions
1. Side gap of 15 mm is required and acts as side panel of drawer. (Fig. 1)
250.0
248.0
2. 25 mm clearance from top edge of drawer required to tilt and remove
64.0
drawer. (Fig. 2)
267.0
3. Fixed slide should be set by 2 mm for 'Auto-Closing.' (Fig. 2)
4. Screws should be recessed to avoid fouling.
64.0
5. Fixed slides should be fitted parallel and at equal heights to each other.
6. Front facia is to be fitted into front brackets which have 2 way adjustment
for alignment.
Specifications 15.0
Power Coated
25.4 (1")
Fixed Slide
2 mm
Caution :
Full panel
For efficiency and durability. Slide
1. Strictly maintain side gap of 15.5 per side.
2. Fix slides are parralel and equal height.
Fig. 2 Side View
3. Do not apply pain or polish.
12
Full Panel Full Extension Drawer Slides
Special Features
! Simplifies construction of drawer as it eliminates the sides of drawers. ! Front fascia adjustment.
! Saves wood, labour, drawer space, time & cost. ! Ribbed for strength.
! Full extension of drawer provided. ! Ideal for filing drawers where full extension of drawer
! Slide latches and wheel catches provided on both sides to prevent the is necessary.
slides from getting disengaged while working. ! System-32 compatible.
! Auto-closing of drawer. ! 25 kgs load capacity.
6.00
300
550
64.00
600
Specifications
FFDS 54-30 FFDS 86-30 FFDS 125-30 FFDS 150-30 300 335
FFDS 54-35 FFDS 86-35 FFDS 125-35 FFDS 150-35 350 385
FFDS 54-37 FFDS 86-37 FFDS 125-37 FFDS 150-37 375 410
Powder
FFDS 54-40 FFDS 86-40 FFDS 125-40 FFDS 150-40 400 435 Coated
Black,
FFDS 54-45 FFDS 86-45 FFDS 125-45 FFDS 150-45 450 485 15.5 30
Brown
and
FFDS 54-50 FFDS 86-50 FFDS 125-50 FFDS 150-50 500 535 Ivory.
FFDS 54-52 FFDS 86-52 FFDS 125-52 FFDS 150-52 525 560
FFDS 54-55 FFDS 86-55 FFDS 125-55 FFDS 150-55 550 585
FFDS 54-60 FFDS 86-60 FFDS 125-60 FFDS 150-60 600 635
13
11
Fitting Instructions
1. To install Full Panel Full Extension Drawer Slide a 15.5mm gap per
side is required between cabinet and drawer. A total of 31 mm for
A B C D
both sides (Refer fig.1). (mm) (mm) (mm) (mm)
2. Fit the outer slide onto the inside of the cabinet
(Refer fig.2). Leave 6mm from the front edge.
54 90 79 32
3. Assemble the intermediate slide with the outer slide and slide it
forward till it stops (Refer fig.3). 86 122 111 64
4. Complete the drawer by adding front, back and bottom panels to
125 161 150 96
the Full Panel. Make sure the slide latches (red color) is pulled
forward (Refer fig.4B). 150 186 175 128
5. Slide the full panel into the intermediate slide
(Refer fig.5). Move the slide latch backward to the locked position
(Refer fig.4A).
15.5
6. For removal of drawer, move slide latches (Red color) forward. The
drawer can now be tilted and removed. (Refer fig.4B).
7. Slides should be fitted parallel to each other and screws tightened
fully, to avoid gaps or interference with wheels.
Caution
B
D
C
A
6.0
Fig.2 Fig.3
B A
BACKWARD
FORWARD TO LOCK
TO ASSEMBLE
OR TO REMOVE
Fig.4 Fig.5
14
Fullpanel Quick Fit
Design Reg. No: 202444
Special Features
! A unique new way to assemble a drawer by ! Autoclosing of drawer.
clipping on a matching back panel. ! Front facia adjustment.
! This not only improves the look of the drawer but ! Precision rollers for smooth running.
also saves valuable time during assembly and ! 'System 32' compatible.
brings down cost.
! Tilt and remove capability with guiding.
Specifications
375
25.4 (1")
1. Side gap of 15.5mm is required and acts as side panel of drawer (Fig.1).
2. 25mm clearance from top edge of drawer required to tilt and remove drawer (Fig. 2). Fig. 2 SIDE VIEW
3. Fixed slide should be set by 2mm for 'Auto-Closing’ (Fig. 2).
4. Screws should be recessed to avoid fouling.
5. Fixed slides should be fitted parallel and at equal heights to each other.
6. Insert the Rear panel onto the Side panels through the key slot provided in the side panels (Ref. Fig.3).
7. Place the bottom flap through the track provided in the Side panels and fix the front facia with the
Bracket and insert the unit onto Fixed slides which are fitted internal sides of cabinet (Ref. Fig.4).
Caution
For efficiency and durability:
1. Strictly maintain side gap of 15.5mm per side
2. Fix slides are parallel and at equal height.
3. Do not apply paint or polish.
Fig. 4 Fig. 3
15
11
Fullpanel Quick Fit File Drawer
Design Reg. No: 207641
1. Side gap of 15.5mm is required and acts as side panel of drawer (Fig. 1).
2. Fixed slide should be set by 2mm for ‘Auto-closing’ (Fig. 2).
3 Screws should be recessed to avoid fouling.
4. Fixed slides should be fitted parallel and at equal heights to each other. 15.5
5. Insert the raised rear panel on to the side panels through the key slot provided in the side panels
(Ref. Fig. 3).
6. Slide the 6mm bottom panel through the tracks provided in the side panels. (Ref. Fig. 4).
7. Connect the cross rods by using T-connectors as shown in diagram (Ref. Fig. 5).
142.0
8. Screw the front facia with side panels and insert the dowel in to the Ø8 hole made in front facia
125.0
123.0
96.0
screw the side rods in to dowels (Ref. Fig. 6). Push the other end of the rod in to the rubber
bushes fitted on the raised rear panel (Ref. Fig. 7).
CABINET
Fig.1 FRONT VIEW
Fixed Slide
2mm
Full Panel
Slide
'A'
.5 0
115 Ø8. eep
d
10
96.0 152.0
16
Full Panel Quick Fit Full Extension
Special Features
! A unique new way to assemble a drawer by clipping on a matching back panel.
! This not only improves the look of the drawer but also saves valuable time
during assembly and brings down cost.
! Tilt and remove capability with guiding.
! Full extension of drawer provided.
! Slide latches and wheel catches provided on both sides to prevent the slides
from getting disengaged while working.
! 'Auto-Closing' of drawer.
! Front facia adjustment.
! Ribbed for strength.
! 'System 32' Compatible.
! 25 Kgs. of load capacity.
Specifications
Fitting Instructions
1. To install Full Panel Full Extension Drawer Slide a 15.5mm gap per side is required
between cabinet and drawer. A total of 31 mm for both sides. (Refer Fig.1)
2. Insert the Rear panel onto the Side panels through the key slot provided in the side 15.5
panels. (Ref. Fig.2)
3. Place the bottom flap through the track provided in the Side panels and fix the front
facia with the Bracket.(Ref. Fig.3)
4. Fit the outer slide onto the inside of the cabinet. Leave 6 mm from the front edge.
(Refer Fig.4)
5. Assemble the intermediate slide with the outer slide and slide it forward till it stops.
161.0
(Refer Fig. 5)
150.0
125.0
6. Complete the drawer by adding front, back and bottom panels to the Full Panel,
96.0
Make sure the slide latches (red color) is pulled forward. (Refer Fig. 6B)
7. Slide the Full panel into the intermediate slide. Refer Fig.7. Move the slide latch
backward to the locked position. (Ref. Fig.6A)
8. For removal of drawer, move slide latches(Red color) forward. The drawer can 8.5
now be tilted and removed. (Ref. Fig.6B) 17.0
9. Slides should be fitted parallel to each other and screws tightened fully, to avoid Fig. 1
gaps or interference with wheels.
17
Fig. 2 Fig. 3
6.0
Fig. 4 Fig. 5
B A
FORWARD
BACKWARD
TO ASSEMBLE
TO LOCK
OR TO REMOVE
Fig. 6 Fig. 7
18
Full Panel Quick Fit Full Extension File Drawer
Design Reg. No. 207640
Special Features
! Special Raised rear panel is ideal for filing cabinets.
! A unique new way to assemble a drawer by clipping on a matching back panel.
! This not only improves the look of the drawer but also saves valuable time during
assembly and brings down cost.
! Full extension of drawer provided.
! Tilt and remove capability with guiding.
! Autoclosing of drawer.
! Front facia adjustment.
! Precision rollers for smooth running.
! System 32 compatible.
Specifications
Code No. Height Depth Width ‘A’ Extn. Max. Load Finish
Kgs.
FFQ 125-40-40 F 125 400 400 340
*FFQ 125-40-40 FG1 125 400 400 340 15.5
435
FFQ 125-40-45 F 125 400 450 390
Powder Coated
*FFQ 125-40-45 FG2 125 400 450 390 Black, Brown &
25
FFQ 125-45-40 F 125 450 400 340 Ivory
*FFQ 125-45-40 FG3 125 450 400 340
485
FFQ 125-45-45 F 125 450 450 390
161.0
*FFQ 125-45-45 FG4 125 450 450 390 150.0
125.0
96.0
Fitting Instructions
1. To install Full Panel Full Extension Drawer Slide a 15.5 mm gap per side is required between 8.5
cabinet and drawer. A total of 31 mm for both sides. (Ref. Fig.1) 17.0
2. Insert the Raised Rear panel onto the side panels through the key slot provided in the side Fig. 1
panels. (Ref. Fig.2)
3. Slide the 6 mm bottom panel through the tracks provided in the side panels.( Ref. Fig.3)
4. Connect the cross rods by using T- connectors as shown in diagram.(Ref.Fig.4)
5. Fix the front facia with side panels by using the clip-on mechanism and lock it by rotating the
lever as shown in diagram and insert the dowel into the Ø8 mm hole made in front facia and
screw the rods in it. (Ref. Fig. 5). Push the other end of the rod into the plastic sleeves fitted on
the Raised rear panel. (Ref. Fig.6)
6. Fit the fixed slide onto the inside of the cabinet. Leave 6 mm from the front edge. (Ref. Fig.7)
7. Assemble the intermediate slide with the fixed slide and slide it forward till it stops. (Ref. Fig. 8)
8. Slide the File drawer assembly into the intermediate slide. (Ref. Fig.10). Make sure that the
slide latches(red colour) are pulled forward.(Ref.Fig.9B) After engaging the drawer assembly
into the intermediate slide move the slide latches backward to the locked position. (Ref.Fig.9A)
9. For removal of drawer, move slide latches(Red color) forward. The drawer can now be tilted
and removed. (Ref. Fig. 9B)
10. Slides should be fitted parallel to each other and screws tightened fully, to avoid gaps or Fig. 2
interference with wheels.
19
Fig. 3 Fig. 4
'A' 0
Ø8. eep
2.5 0 d
1
189.0
ROTA
TE L
E
TO LVER
OCK
32.0
Fig. 5 Fig. 6
6.0
Fig. 7 Fig. 8
B A
FORWARD BACKWARD
TO ASSEMBLE TO LOCK
OR TO REMOVE
Fig. 9 Fig. 10
20
Full Extension Drawer Slides
Design Reg. No: 181904/00
Special Features
! Full extension of drawer provided. ! Screw holes as per System 32.
! Slide latches and wheel catches provided on both ! Lateral guiding provided.
sides to prevent the slides from getting disengaged ! 25 kgs load capacity.
while working.
! Ideal for kitchen baskets where full extension of drawer
! Inner Slide has Bottom Mounting. is necessary.
6.00
300
450
64.00
500 & 525
550
64.00
600
Front Edge
of Cabinet 32.00 128.00 96.00 96.00 96.00 96.00
Specifications
21
Fitting Instructions
1. To install Full Extension Drawer Slide a 12.7mm (1/2") 12.7
gap per side is required between cabinet and drawer. A 1/2"
total of 25.4mm ( 1") for both sides (Refer fig. 1).
2. Fit the outer slide onto the inside of the cabinet (Refer
Fig.2).
3. Assemble the intermediate slide with the outer slide and
60.0
slide it forward till it stops (Refer fig. 3).
50.0
Cabinet
Drawer
4. Fit the inner slide onto the drawer. Make sure the slide
latches (red color) is pulled forward (Refer fig. 4B).
7.0
5. Slide the inner slide with the drawer into the intermediate
slide (Refer fig. 5). Move the slide latch backward to the
locked position (Refer fig 4A). Fig.1 FRONT VIEW
6. For removal of drawer, move slide latches (Red color)
forward. The drawer can now be tilted and removed.
7. Slides should be fitted parallel to each other and screws
tightened fully, to avoid gaps or interference with wheels.
6.0
Caution
For efficiency and durability.
1. Side gap of 12.7 mm (1/2") per side is most important.
2. Fix slides parallel and at equal height.
3. Do not remove Red Latch.
Fig.2
Fig.3
A
B
BACKWARD
FORWARD TO LOCK
TO ASSEMBLE
OR TO REMOVE
Fig.4 Fig.5
22
Fascia Swivel Bottom Mounting Drawer Slides
Specifications
Length Extension Gap/Side Max. Load
Code No.
(mm) (mm) (mm) Kgs. Fig. 1 FRONT VIEW
BMDS 35 FS 350 260
CABINET
BMDS 40 FS 400 310 12.7
Clearance
25.4mm
Top
1"
BMDS 45 FS 450 360 (1/2”) 20
Fig. 3
Fig. 4 Fig. 5
23
Sleek Telescopic Drawer Slide (I)
Special Features
! Precision ball bearing.
! Full extension of drawer.
! Load capacity 35 Kgs.
! Direct fitting from front.
! Removable drawer with Latch
! System 32 installation.
250
32.0 32.0
300
32.0 32.0
350
64.0 32.0 32.0
400
32.0 32.0
450 64.0 32.0 32.0
500
64.0 64.0 32.0
550
64.0 32.0 32.0
600
32.0 32.0
750
32.0 32.0 64.0 64.0 64.0 96.0 96.0 96.0 96.0 64.0 64.0 64.0 32.0
900
.2
Ø4
Front Edge DRILLING DIAGRAM FOR CABINET
of Cabinet
24
Specifications
4. Slides should be fitted parallel and screws tightened fully to avoid gaps.
5. Fit inner slide onto the outside of the drawer.
6. Now slide the drawer with inner slide fluted on to the intermediate slides Minimum
CABINET
DRAWER Bottom
on the cabinet till the latch will automatically engage. Clearance
1/8"
CABINET 3.2
Caution
For efficiency and durability: 12.7
1. Strictly maintain 12.7 to 13.Omm side gap. 13.0
Fig. 1
2. Fit slides parallel and at equal heights.
3. Do not apply paint or polish.
4. Do not let saw dust enter into the slides.
Depress Latch
to Remove Inner Slide
Fig. 2
25
Sleek Telescopic Drawer Slides-Auto Closing (I)
Special Features
! New Auto closing feature.
! Precision ball bearing.
! Full extension of drawer.
! Load capacity 35 Kgs.
! Direct fitting from front.
! Removable drawer with latch.
! System 32 installation.
Specifications
1. To install sleek telescopic drawer slide 12.7 to13.0mm side gap per
1/8"
3.2
Caution
For efficiency and durability:
1. Strictly maintain 12.7 to 13.Omm side gap.
2. Fit slides parallel and at equal heights.
3. Do not apply paint or polish.
4. Do not let saw dust enter into the slides. Depress Latch
to Remove Inner Slide
Fig. 2
26
Mini Drawer Slide H-17
Special Features
±0.2
1. Lateral play is virtually eliminated when the 10.0
groove mounting method is employed.
2. This slide is small, elegant and space saving.
3. Accessible from both sides.
4. 32mm hole pattern.
±0.2
5. Max. load capability - 10kg/set.
25.5
Specifications
Drawer Depth Length of drawer Length of cabinet Extension loss of
Item Code
mm slide ‘L1’ mm slide ‘L2’ mm drawer ‘A’ mm
±0.2
MDS 21 214-341 214 214 70 10.0
Side Gap 7.5
MDS 31 310-506 310 310 94
Groove
17.0
Fitting Instructions
1. Side gap required is 10.0mm per side including
DRAWER
the groove (Ref. Fig. 1).
2. Make a groove in the drawer as per given
dimensions (Ref. Fig. 1).
CABINET
3. Fix the cabinet slide to the cabinet (Ref. Fig. 2).
Fig.1
4. Fix the drawer slide to the drawer with the M4
screws provided (Ref. Fig. 2).
L1
A
L2
M4 x 2 Nos 8.0
32.0 8.0
Caution 1.0
44.0
27.0
1. Side gap required is 10.0mm per side is
most important.
Drawer Depth
2. Fix slides parallel and at equal height.
3. Do not apply paint or polish.
Fig.2
4. Do not let saw dust enter in to the slides.
27
Mini Telescopic Drawer Slides H- 36
Special Features
1. Easy to pullout, pull release for disconnect.
2. Ball retainer detent for drawer easy re-install.
3. Hold-in detent.
4. Side space adjustable tabs and non-handed.
5. 32mm hole pattern.
Specifications
Item Code Slide Length Extension Gap/Slide Max. Load Finish
mm mm mm Kgs.
Fitting Instructions
36.0
1. Side gap required is 12.7mm (½”) per side (Ref. Fig. 1).
2. Fix the outer (fixed) slides to the cabinet. Access to holes can be got
through slots in intermediate slide (Ref. Fig. 1).
3. Press latch and remove the inner slide (Ref. Fig. 2). DRAWER
4. Slides should be fitted parallel and screws tightened fully to avoid gaps.
5. Fit inner slide onto the outside of the drawer. (Ref. Fig. 1). CABINET
6. Now, slide the drawer with inner slide fitted onto the intermediate slides
on the cabinet. Fig.1
Caution
1. Side gap required is 12.7mm per side is most important.
2. Fix slides parallel and at equal height.
3. Do not apply paint or polish.
4. Do not let saw dust enter in to the slides. Fig.2
28
Basket Slides - 12.7mm
Special Features
! Precision Ball Bearing.
! Full extension of drawer.
! Special clamp arrangement for baskets.
! Basket can be removed by depressing latch.
! Max. Load capacity 35 kg.
400
32.0 32.0
95.0
450
145.0 64.0
500
195.0 32.0 32.0
550
245.0 32.0 32.0
600
Front Edge
of cabinet
29
Specifications
12.7
45.0
12.7
13.0
Depress latch
to remove tray.
Fig. 1 Fig. 2
30
Heavy Duty Telescopic Drawer Slides
Design Reg. No: 162398/90
Special Features
! Full extension of drawer available.
! Direct front installation without De-assembly.
! Precision ball bearing for smooth movement.
! Hole 'System-32' compatible.
400
450
500
550
600
650
700
750
31
Specifications
Fitting Instructions
1. To install, gap per side required is 25mm. (Refer fig. 1)
2. Screw holes are accessible through slots in inner slides.
3. Slides must be fitted parallel and at equal height.
4. Screw outer slides on drawer and inside of cabinet
maintaining parallelism.
Caution
For efficiency and durability. 25.0
1. Side gap of 25 mm (1”) per side is most important.
2. Fit slides parallel and at equal height.
3. Do not apply paint or polish. DRAWER
4. Do not let saw dust enter into the slides.
34.0
Minimum
Bottom
Clearance
1/8”
3.2
CABINET
32
Computer Keyboard Slides
Design Reg. No: 172578/96
Special Features
! Smooth quiet movement with ball bearings.
! Set comes with left and right hand slides.
! Removable drawer with depressible latch.
! Adjustable height on Mounting Brackets. Mounting
Brackets
! Direct front installation.
! Pressure Latch prevents play.
0
! Slides can be fitted top hung or bottom hung. 80 .
Specifications
Caution
For efficiency and durability.
1. Side gap of 20 mm per side is most important Key Board Tray
2. Fix slides parallel and at equal height. Attached to moving slide
3. Do not apply paint or polish. New Pressure Latch prevents play &
movement of Keyboard when pulled out.
4. Do not interchange right and left inner slides. Tray can be completely removed by
depressing Latch.
Fig.2
Adjustment
Height
36.0
Depress latch
to remove
tray.
Fig.3
33
Computer Keyboard Slide - Eco
Special Features
.0
! Basic and economic option. 241
! Having all steel construction with ball cages for long life.
! Has a built in end stop. (Ref. Fig. 1)
Specifications
Latch
0 36.0
32.
.0
Max.
95.0
224
62.0
Min.
34
Two Way Slides
Special Features
! Slim design requires only 10mm side gap.
! Can be used with bigger drawers as slides are reversible.
! No deassembly required.
! "System 32" compatible.
! Precision ball bearing for smooth movement.
! Load capacity - 12kgs.
200
76.00 32.00
300
172.00 32.00
375
128.00 64.00 32.00
420
Specifications
35
Fitting Instructions
1. 10mm side gap required per side. (Refer fig. 1)
2. Can be recessed fitted in a 27mm slot to reduce side gap. (Refer fig. 2)
3. Slide must be parallel and at equal height.
10.0 10.0
6.7
27.0
27.0
13.5
Minimum
Minimum
DRAWER Bottom DRAWER
Bottom
Clearance
Clearance
3.2mm
CABINET CABINET
1/8”
3.2mm
1/8”
Fig.1 Fig.2
CABINET
DRAWER
Extension Loss
Fig.3
Caution
For efficiency and durability.
1. Strictly maintain side gap given in diagrams.
2. Fit slides parallel and at equal heights.
36
Quadrail Slides
Special Features
! This new drawer slide system has a unique design with chrome ! Has a spring loaded auto-closing feature.
steel ball bearings and rollers for long life, smooth working and ! System 32 compatible
two dimensional guiding. ! Saves space due to reduced side gap.
! Easy to fit by just pushing the drawer in and come with a special
Release Clip with built-in Fascia Adjuster.
250
160.00
160.00
300
350 224.00
400
224.00
450
500 288.00
550
40.00 32.00 288.00 32.00
16.00 16.00
600
Specifications
Code Nos. Slide Length Extension Drawer Length Min Cabinet Gap/Side Max. Finish
(mm) (mm) (L) mm depth mm (mm) Load
Kgs.
37
Fitting Instructions
1. Side wall thickness of drawer should not exceed 16mm Max.
and bottom extension of side should not exceed 10mm max.
(Refer fig. 1).
2. Drill hole Ø6mm required at the rear of drawer to anchor the
rear end of slides (Refer fig. 2).
3. Release clips to be fitted the drawer in front of the fascia.
(Refer fig. 3)
4. Mounting brackets of slide to be fitted parallel and at equal
height inside the cabinet leaving 5mm from the front edge
(Refer fig. 4).
5. Push Drawer onto slide and automatically locks onto the
slides. (Refer fig. 5).
6. Fascia can be adjusted by sliding the adjuster.
16.0 Max.
DRAWER 7.0
Ø6.0
11.0
CABINET
28.5
20.0
18.0 20.0
10.0 Max.
Fig.1
'L'
11.0
Facia adjuster to
adjust the level
DRAWER of drawer
CABINET
5.0
Press to
remove the
drawer
Fig.4 Fig.5
38
Side Hinged Door Slide
Special Features
! Cabinet shutter opens 90° and can slide inside the cabinet on each side.
! Channels are mounted inside the cabinet on the side. WOOD STRIP
! Precision ball bearings with European type cup hinges.
! Support rollers reduce sag of door. BRIDGE
! L-shaped bridge provided to fit wood strip to prevent jamming.
SHUTTER
! Adjustable hinges with auto-closing.
! Corner roller for door protection. Ideal for TV cabinet. HINGE SLIDE
CORNER
ROLLER
Specifications
CABINET
Length Min. Width Thickness of Max. weight
Code Nos. Finish
(mm) of shutter (mm) shutter (mm) of shutter (kgs) Fig.1 FRONT VIEW
39
Top Hinged Door Slide
Special Features
! Shutter opens upwards and slides on top of the cabinet. Ideal for
T.V., Bar and filing cabinets.
! Precision ball bearing movement with roller to protect shutter.
! Special cranked hinge.
Specifications
10.0
THDS 40 400 420 275
White
THDS 45 450 470 325 16 Zinc
Plated
THDS 50 500 520 375 Hinge
Slide
THDS 55 550 570 425 SHUTTER
Fig.1
THDS 60 600 620 475
SHUTTER
Fitting Instructions
2.5
3. Slide must be recessed into 35mm wide and 8.6mm deep slots
inside the shutter. (Refer Fig. 3).
4. Hinge must be recessed into the top front edge of cabinet 50mm Fig.2
wide and 10mm deep. (Refer Fig. 4).
5. Opening angle : 90°.
Caution
8.6
Fig.4 Fig.3
40
Premium Sleek Telescopic Slides - Auto Close
Special Features
! Full extension
! 30 mm stroke of Auto - Closing
! Pull force 2.5 kg.
! Non-handed Disconnect Release.
! 45 kg / 100 lbs. loading at 18".
! Electro-Zinc plated with clear, yellow or black chromate,
or Cr-Free galvanized steel.
Specifications
Size Length Extension Max. Load
Code Nos.
(mm) (mm) (mm) (kgs)
300
350
64.0
400
450
160.0
500
550
21.6
9.0
600
8.5
Ø6.
.6
9.0
Ø4
21.3
4
34.3
27.0 128.0 96.0 128.0
front Edge DRILLING DIAGRAM FOR CABINET
Cabinet
41
Fitting Instructions
1. To install Ball bearing slide, 13.0 to 13.6 mm side gap per side is
required between cabinet and drawer. (Refer Fig. 1)
2. Fit outer (fixed) slide onto the inside of the cabinet, access to holes can be
got through slots in intermediate slide
3. Slides should be fitted parallel and screws tightened fully to avoid gaps.
4. Fit inner slide onto the outside of the drawer.
5. Now slide the drawer with inner slide fitted on to the intermediate slides
on the cabinet till the latch will automatically engage.
+0.6
-0 +0.2
13.0 -0
12.8
±0.3
45.5
Fig. 1
30 mm stroke of Auto-Closing
+0.5
flush +0.5 -0
-0 8.5
35
Caution
For efficiency and durability :
1. Strictly maintain 13.0 to 13.6 mm side gap.
2. Fit slides parallel and at equal heights.
3. Do not apply paint or polish.
4. Do not let saw dust enter into the slides.
42
Premium Sleek Telescopic Slides - Soft close
Special Features
! 30 mm stroke of Soft - Closing
! Pull force 3.2 - 3.5 kg
! Soft-closing function built in slide, easy for installation.
! Non-handed Disconnect Release.
! 45 kg / 100 lbs. loading at 20".
! Electro-Zinc plated with clear, yellow or black chromate, or Cr-Free galvanized steel.
Specifications
Size Length Extension Extension Loss Max. Load
Code Nos.
(mm) (mm) (mm) (mm) (kgs)
300 128.0
350
400
80.0
450
128.0
500
176.0
550
21.6
9.0
600
8.5
9.0 21.6
34.3
27.0 128.0 96.0 128.0
Front Edge
Cabinet DRILLING DIAGRAM FOR CABINET
43
Fitting Instructions
1. To install Ball bearing slide, 13.0 to 13.8 mm side gap per side is
required between cabinet and drawer. (Refer Fig. 1)
2. Fit outer (fixed) slide onto the inside of the cabinet, access to holes can be
got through slots in intermediate slide
3. Slides should be fitted parallel and screws tightened fully to avoid gaps.
4. Fit inner slide onto the outside of the drawer.
5. Now slide the drawer with inner slide fitted on to the intermediate slides
on the cabinet till the latch will automatically engage.
+0.2
+0.8 -0
-0 12.8
13.0
±0.3
45.5
Fig. 1
30 mm stroke of Soft-Closing
+0.5
flush +0.5 -0
-0 8.5
35
Caution
For efficiency and durability :
1. Strictly maintain 13.0 to 13.8 mm side gap.
2. Fit slides parallel and at equal heights.
3. Do not apply paint or polish.
4. Do not let saw dust enter into the slides.
44
Premium Sleek Telescopic Slides - Push Open
Specifications Caution
Size Length Extension Max. Load For efficiency and durability :
Code No.
mm mm mm kgs
1. Strictly maintain 13.0 to 13.8 mm side gap.
P-STDS-40-PO 400 400 406 40 2. Fit slides parallel and at equal heights.
P-STDS-45-PO 450 450 457 45 3. Do not apply paint or polish.
4. Do not let saw dust enter into the slides.
P-STDS-50-PO 500 500 508 45
400
450
160.0
21.6
9.0
500
8.5
Ø6.
.6
9.0
Ø4
21.6
34.3
27.0 128.0 96.0 128.0
Front Edge
Cabinet DRILLING DIAGRAM FOR CABINET
45
+0.8 +0.2
-0 -0
13.0 12.8
±0.3
45.5
Fig. 1
+0.8 +0.8
-0 -0
13.0 Max. drawer width 13.0
Without Gasket
58.0 + t
GAP 3±0.5 mm t
PUSH 2 mm PUSH 2 mm
'X'
With Gasket (Anti insect)
t= Gasket
t= thickness of gasket max. 8mm
pressed amount of gasket min. 2.5mm
Gasket
Side Panel (Anti insect)
flush
t A Front Panel of Drawer
Min 2.5mm
PUSH
9 54.6-A
35
Top View (View from 'X')
46
Premium Quadrail - Auto Close
Specifications
Min. internal cabinet
Normal Drawer Load Depth for Standard Over
Size
Code No. Runner Capacity Drawer
mm Length Length Kgs. Travel
Overlay Inset +1
-0
P-CDS-30 300 300 290 25 310 328 10 32 37
9 9 9 9 +1
P-CDS-35 350 350 340 360 378 10
Ø6
30 -0
.3
4
P-CDS-40 400 400 390 35 410 428 10
26 12
±0.5
P-CDS-50 500 500 490 35 510 528 10
22 10
450
+10
-1
500 internal drawer width = internal carcase width-41 mm
internal carcase width
internal drawer width
550 max 16
7
12-14
600
+1
±0.5
±0.5
-0
28.5 11
38
32
26
37
128
224 Front Edge
247 20.5 20.5
of Cabinet
288
max 16
7 0
X1
Ø6
max 14
11
12
28.5±0.5
26±0.5
3-sided-drawer
Inset-drawer
90º
mm
= 3.5
jus t ment ard
t Ad upw
Heigh Provides nt only
t m e
adjus
7
11
Ø6X10 Depth
8.6
25.8 20
14.8 42
48
Premium Quadrail - Soft Close
Specifications
Min. internal cabinet
Normal Drawer Load Depth for Standard Over
Size
Code No. Runner Capacity Drawer
mm Length Length Kgs. Travel
Overlay Inset
P-CDS-30-SC 300 300 290 25 310 328 10 +1
-0
32 37
P-CDS-35-SC 350 350 340 30 360 378 10
9 9 9 9 +1
Ø6
P-CDS-40-SC 400 400 390 35 410 428 10 -0
.3
4
P-CDS-45-SC 450 450 440 40 460 478 10
P-CDS-50-SC 500 500 490 35 510 528 10
26 12
±0.5
P-CDS-55-SC 550 550 540 35 560 578 10
P-CDS-60-SC 600 600 590 30 610 628 10
350 37 32
37 32 Inner Drawer
450
22 10
500
+10
-1
internal drawer width = internal carcase width-41 mm
550 internal carcase width
internal drawer width
max 16
600
+1
7
-0
12-14
32 37
128
224 Front Edge
±0.5
±0.5
247
28.5 11
38
of Cabinet
26
288
20.5 20.5
DRILLING DIAGRAM FOR CABINET
49
4-sided-drawer
+0
-0.5
20.5
max 16
7 0
X1
Ø6
max 14
11
12
28.5±0.5
26±0.5
3-sided-drawer
Inset-drawer
90º
mm
= 3.5
jus t ment ard
t Ad upw
Heigh Provides nt only
t m e
adjus
7
11
Ø6X10 Depth
8.6
25.8 20
14.8 42
50
Premium Quadrail - Push Open
Special Features
! Push-rebound function built in slide, easy for installation
+0
! Full extension -0.5
! Suited to wooden drawer. 20.5
max 16
! With Easy - Release Catch.
! 40 kg / 90 lbs. loading at 18". 7 0
X1
! Ball bearing slide offers strong structure and avoids sway Ø6
max 14
! Fully push in (2 mm) for open or close
28.5±0.5 11
26±0.5 12
Under horizontal installation, drawer will redound 5" - 8"
when pushing
! Cr-free galvanized steel.
Specifications
Drawer Min. internal
Normal Length Load Max.
Size Carcase Over
Code No. Runner Rating Drawer
mm Length +0 Depth for Travel
kg/pr Width
-1.5 Drawer
P-CDS-50-PO 500 500 490 35 700 510 10
Fitting Instructions
1. Install the slides as per given diagrams.
500
+1
-0
32 37
128
Front Edge
224
of Cabinet
247
51
+1
-0
32 37
9 9 9 9 +1
Ø6
-0
.3
4
26 12
±0.5
90º
m
3.5m
e n t= +
justm ard
ht A d u pw
Heig ides ly
Prov ment on
d j u s t
a
8.6
7
11 Ø6X10 Depth
25.8 20
14.8 42
+0
-1
Internal drawer width=internal carcase -41 mm
min. carcase depth GAP 4-5 mm
+0 Internal carcase width
Drawer length -1.5
max. drawer width
+0 internal drawer width
-1
37
PUSH
2 mm
PUSH
52