Documente Academic
Documente Profesional
Documente Cultură
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Hempel's Galvosil 15780 must be fully cured prior to application of the 2nd coat.
water rinsing. Salts and other contamination to be removed by high pressure fresh water Approximate curing time is 24 hours at 20 deg C (75% RH). In case of very low humidity,
hosing. When the surface is dry: abrasive blast to Sa. 2½ according to ISO 8501-1:2007 hose down surface with fresh water 1-2 hours after application to ensure curing of 15780.
with a surface profile corresponding to Rugotest No. 3 BN 10, Keane-Tator Comparator Continuously wet the surface until full curing is completed.
Disc, 3.0 G/S, or ISO Comparator Medium (G). Dedust and clean surface prior to
painting. Check curing condition by rubbing with piece of cloth soaked with Thinner 08700 (ASTM
D4752-03 Solvent-Rub Test). If the coating remains unaffected, the curing is complete.
Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush Apply mist coat of 45881 first on cured primer (15780) prior to full coat spray application
prior to full spray coat application. to avoid pinholes and minimise popping.
NOTE :
1). This Painting Specification is made based on client's specification.
2). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPEL'S GALVOSIL 15780 f/c 100 Metal grey 19840 100 65 9.5 X X .019"-.023" 100 bar
HEMPADUR MASTIC 45881 f/c 100 Grey 13600 150 110 7.3 (X) X .017"-.023" 250 bar
HEMPADUR MASTIC 45881 f/c 100 To Be Advised T.B.A 125 100 8.0 (X) X .017"-.023" 250 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 275 X: Recommended (X): Possible
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 2
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time and recoating intervals.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPEL'S GALVOSIL 15780 19840 62 97170 8:2 4h 30 min 14 08700 0
HEMPADUR MASTIC 45881 13600 80 95881 3:1 1 h 30 min 3h 39 08450 15
HEMPADUR MASTIC 45881 T.B.A 80 95881 3:1 1 h 30 min 3h 39 08450 15
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 3
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution by thorough fresh water Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove salts and prior to full spray coat application.
other contaminants. When the surface is dry: Abrasive blasting to minimum Sa 2½ NOTE :
according to ISO 8501-1:2007. Dedust and clean surface prior to painting. 1). This Painting Specification is made based on client's specification.
2). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR HB PRIMER 17300 f/c 100 Yellow 21780 100 50 11.2 X X .021" 175 bar
HEMPADUR MASTIC 45881 f/c 100 Grey 13600 125 100 8.0 (X) X .017"-.023" 250 bar
HEMPADUR MASTIC 45881 f/c 100 To Be Advised T.B.A 150 125 6.4 (X) X .017"-.023" 250 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 275 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time and recoating intervals.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR HB PRIMER 17300 21780 56 95010 5:1 8h 2h 26 08450
HEMPADUR MASTIC 45881 13600 80 95881 3:1 1 h 30 min 3h 39 08450 15
HEMPADUR MASTIC 45881 T.B.A 80 95881 3:1 1 h 30 min 3h 39 08450 15
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 5
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove prior to full spray coat application.
salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa NOTE :
2½ according to ISO 8501-1:2007 with a surface profile corresponding to Rugotest No. 3 1). See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
BN 10a-b or Keane-Tator Comparator Disc, min. 3.0 G/S, 2-3 S, or ISO Comparator, and recoating intervals. Please follow the minimum and maximum recoating time interval
Medium (G). Dedust and clean surface prior to painting. of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR ZINC 17360 f/c 100 Metal grey 19840 75 40 16.3 (X) X .017"-.021" 150 bar
HEMPADUR MASTIC 45881 f/c 100 Grey 13600 150 110 7.3 (X) X .017"-.023" 250 bar
HEMPADUR MASTIC 45881 f/c 100 To Be Advised T.B.A 125 100 8.0 (X) X .017"-.023" 250 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 250 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR ZINC 17360 19840 65 97040 4:1 2h 1h 24 08450 -10 85
HEMPADUR MASTIC 45881 13600 80 95881 3:1 1 h 30 min 3h 39 08450 15
HEMPADUR MASTIC 45881 T.B.A 80 95881 3:1 1 h 30 min 3h 39 08450 15
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 7
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Hempel's Galvosil 15780 must be fully cured prior to application of the 2nd coat.
water rinsing. Salts and other contamination to be removed by high pressure fresh water Approximate curing time is 24 hours at 20 deg C (75% RH). In case of very low humidity,
hosing. When the surface is dry: abrasive blast to Sa. 2½ according to ISO 8501-1:2007 hose down surface with fresh water 1-2 hours after application to ensure curing of 15780.
with a surface profile corresponding to Rugotest No. 3 BN 10, Keane-Tator Comparator Continuously wet the surface until full curing is completed.
Disc, 3.0 G/S, or ISO Comparator Medium (G). Dedust and clean surface prior to
painting. Check curing condition by rubbing with piece of cloth soaked with Thinner 08700 (ASTM
D4752-03 Solvent-Rub Test). If the coating remains unaffected, the curing is complete.
Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush Apply mist coat of 45881 first on cured primer (15780) prior to full coat spray application
prior to full spray coat application. to avoid pinholes and minimise popping.
NOTE :
1).See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
and recoating intervals. Please follow the minimum and maximum recoating time interval
of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
HEMPEL'S GALVOSIL 15780 f/c 100 Metal grey 19840 100 65 9.5 X X .019"-.023" 100 bar
HEMPADUR MASTIC 45881 f/c 100 Grey 13600 125 100 8.0 (X) X .017"-.023" 250 bar
HEMPATHANE TOPCOAT 55210 f/c 100 To Be Advised T.B.A 75 40 12.5 (X) (X) X .017"-.019" 150 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 205 X: Recommended (X): Possible
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 9
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPEL'S GALVOSIL 15780 19840 62 97170 8:2 4h 30 min 14 08700 0
HEMPADUR MASTIC 45881 13600 80 95881 3:1 1 h 30 min 3h 39 08450 15
HEMPATHANE TOPCOAT 55210 T.B.A 50 95370 7:1 4h 8h 33 08080 -10
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 10
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove prior to full spray coat application.
salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa NOTE :
2½ according to ISO 8501-1:2007. Dedust and clean surface prior to painting. 1). See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
and recoating intervals. Please follow the minimum and maximum recoating time interval
of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR HB PRIMER 17300 f/c 100 Yellow 21780 100 50 11.2 X X .021" 175 bar
HEMPADUR MASTIC 45881 f/c 100 Grey 13600 125 100 8.0 (X) X .017"-.023" 250 bar
HEMPATHANE TOPCOAT 55210 f/c 100 To Be Advised T.B.A 75 40 12.5 (X) (X) X .017"-.019" 150 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 190 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR HB PRIMER 17300 21780 56 95010 5:1 8h 2h 26 08450
HEMPADUR MASTIC 45881 13600 80 95881 3:1 1 h 30 min 3h 39 08450 15
HEMPATHANE TOPCOAT 55210 T.B.A 50 95370 7:1 4h 8h 33 08080 -10
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 12
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove prior to full spray coat application.
salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa NOTE :
2½ according to ISO 8501-1:2007 with a surface profile corresponding to Rugotest No. 3 1). See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
BN 10a-b or Keane-Tator Comparator Disc, min. 3.0 G/S, 2-3 S, or ISO Comparator, and recoating intervals. Please follow the minimum and maximum recoating time interval
Medium (G). Dedust and clean surface prior to painting. of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR ZINC 17360 f/c 100 Metal grey 19840 75 40 16.3 (X) X .017"-.021" 150 bar
HEMPADUR MASTIC 45881 f/c 100 Grey 13600 150 110 7.3 (X) X .017"-.023" 250 bar
HEMPATHANE TOPCOAT 55210 f/c 100 To Be Advised T.B.A 75 40 12.5 (X) (X) X .017"-.019" 150 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 190 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time and recoating intervals.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR ZINC 17360 19840 65 97040 4:1 2h 1h 24 08450 -10 85
HEMPADUR MASTIC 45881 13600 80 95881 3:1 1 h 30 min 3h 39 08450 15
HEMPATHANE TOPCOAT 55210 T.B.A 50 95370 7:1 4h 8h 33 08080 -10
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 14
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Salts and other contamination to be removed by high pressure fresh water prior to full spray coat application.
hosing. When the surface is dry: abrasive blast to Sa. 2½ according to ISO 8501-1:2007 NOTE :
with a surface profile corresponding to Rugotest No. 3 BN 10a, Keane-Tator Comparator 1). See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
Disc, 3.0 G/S, or ISO Comparator Medium (G). Dedust and clean surface prior to and recoating intervals. Please follow the minimum and maximum recoating time interval
painting. of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR 85671 f/c 100 Light red 50900 150 100 6.8 X X .018"-.021" 200 bar
HEMPADUR 85671 f/c 100 Green 42070 150 100 6.8 X X .018"-.021" 200 bar
HEMPADUR 85671 f/c 100 Light red 50900 150 100 6.8 X X .018"-.021" 200 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 300 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR 85671 50900 68 97371 8.8 : 1.2 3h 6h 24 08450 10 80
HEMPADUR 85671 42070 68 97371 8.8 : 1.2 3h 6h 24 08450 10 80
HEMPADUR 85671 50900 68 97371 8.8 : 1.2 3h 6h 24 08450 10 80
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 16
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Salts and other contamination to be removed by high pressure fresh water prior to full spray coat application.
hosing. When the surface is dry: abrasive blast to Sa. 2½ according to ISO 8501-1:2007 NOTE :
with a surface profile corresponding to Rugotest No. 3 BN 10a, Keane-Tator Comparator 1). See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
Disc, 3.0 G/S, or ISO Comparator Medium (G). Dedust and clean surface prior to and recoating intervals. Please follow the minimum and maximum recoating time interval
painting. of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR 85671 f/c 100 Light red 50900 150 100 6.8 X X .018"-.021" 200 bar
HEMPADUR 85671 f/c 100 Green 42070 150 100 6.8 X X .018"-.021" 200 bar
HEMPADUR 85671 f/c 100 Light red 50900 150 100 6.8 X X .018"-.021" 200 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 300 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR 85671 50900 68 97371 8.8 : 1.2 3h 6h 24 08450 10 80
HEMPADUR 85671 42070 68 97371 8.8 : 1.2 3h 6h 24 08450 10 80
HEMPADUR 85671 50900 68 97371 8.8 : 1.2 3h 6h 24 08450 10 80
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 18
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Salts and other contamination to be removed by high pressure fresh water prior to full spray coat application.
hosing. When the surface is dry: abrasive blast to Sa. 2½ according to ISO 8501-1:2007 NOTE :
with a surface profile corresponding to Rugotest No. 3 BN 10a, Keane-Tator Comparator 1).See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
Disc, 3.0 G/S, or ISO Comparator Medium (G). Dedust and clean surface prior to and recoating intervals. Please follow the minimum and maximum recoating time interval
painting. of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR 85671 f/c 100 Green 42070 150 100 6.8 X X .018"-.021" 200 bar
HEMPADUR 85671 f/c 100 Light red 50900 150 100 6.8 X X .018"-.021" 200 bar
HEMPADUR 85671 f/c 100 Green 42070 150 100 6.8 X X .018"-.021" 200 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 300 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR 85671 42070 68 97371 8.8 : 1.2 3h 6h 24 08450 10 80
HEMPADUR 85671 50900 68 97371 8.8 : 1.2 3h 6h 24 08450 10 80
HEMPADUR 85671 42070 68 97371 8.8 : 1.2 3h 6h 24 08450 10 80
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 20
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Salts and other contamination to be removed by high pressure fresh water prior to full spray coat application.
hosing. When the surface is dry: abrasive blast to Sa. 2½ according to ISO 8501-1:2007 NOTE :
with a surface profile corresponding to Rugotest No. 3 BN 10b, Keane-Tator Comparator 1).See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
Disc, 3.0 G/S, or ISO Comparator Medium (G). Dedust and clean surface prior to and recoating intervals. Please follow the minimum and maximum recoating time interval
painting. of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR 85210 f/c 100 Yellow 21240 175 100 6.0 (X) X .021" 150 bar
HEMPADUR 85210 f/c 100 Off white 11630 175 100 6.2 (X) X .021" 150 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 200 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR 85210 21240 60 89110 4:1 2h 5h 37 08450 10
HEMPADUR 85210 11630 62 89110 4:1 2h 5h 37 08450 10
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 22
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove prior to full spray coat application.
salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa NOTE :
2½ according to ISO 8501-1:2007 with a surface profile corresponding to Rugotest No. 3 1). This Painting Specification is made based on client's specification.
BN 11a, Keane-Tator Comparator Disc, 5.5 G/S, or ISO Comparator Coarse (G). Dedust 2). Consult the Product Data Sheets for further technical information and clarification.
and clean surface prior to painting.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPEL'S VINYL ESTER GF 35910 f/c 100 Off white 11630 775 650 1.3 (X) (X) X .030"-.060" 275 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 650 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time and recoating intervals.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPEL'S VINYL ESTER GF 35910 11630 85 99410 98 : 2 45 min 6h 28 10
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 24
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Salts and other contamination to be removed by high pressure fresh water prior to full spray coat application.
hosing. When the surface is dry: abrasive blast to Sa. 2½ according to ISO 8501-1:2007 NOTE :
with a surface profile corresponding to Rugotest No. 3 BN 10a, Keane-Tator Comparator 1).See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
Disc, 3.0 G/S, or ISO Comparator Medium (G). Dedust and clean surface prior to and recoating intervals. Please follow the minimum and maximum recoating time interval
painting. of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPEL'S COAL TAR EPOXY MASTIC 35670 f/c 100 Brown 60420 225 200 4.6 X X .021"-.023" 250 bar
HEMPEL'S COAL TAR EPOXY MASTIC 35670 f/c 100 Black 19990 225 200 4.6 X X .021"-.023" 250 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 400 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPEL'S COAL TAR EPOXY MASTIC 60420 92 98670 4:1 8h 8h 23 08450 10
35670
HEMPEL'S COAL TAR EPOXY MASTIC 19990 92 98670 4:1 8h 8h 23 08450 10
35670
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 26
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove prior to full spray coat application.
salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa NOTE :
2 according to ISO 8501-1:2007. Dedust and clean surface prior to painting. 1).See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
and recoating intervals. Please follow the minimum and maximum recoating time interval
of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPEL'S ZP ALKYD PRIMER 12090 f/c 100 Yellow 2022S 100 45 10.9 X (X) X .018" 150 bar
HEMPEL'S ZP ALKYD PRIMER 12090 f/c 100 Yellow 2022S 100 45 10.9 X (X) X .018" 150 bar
HEMPEL'S SILVIUM 51570 f/c 100 Light alu 19000 75 25 15.2 (X) X .017'' 100 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 115 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time and recoating intervals.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPEL'S ZP ALKYD PRIMER 12090 2022S 49 2h 38 08230 5
HEMPEL'S ZP ALKYD PRIMER 12090 2022S 49 2h 38 08230 5
HEMPEL'S SILVIUM 51570 19000 38 5h 38
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 28
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove prior to full spray coat application.
salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa NOTE :
2 according to ISO 8501-1:2007. Dedust and clean surface prior to painting. 1).See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
and recoating intervals. Please follow the minimum and maximum recoating time interval
of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPEL'S ZP ALKYD PRIMER 12090 f/c 100 Yellow 2022S 100 50 9.8 X (X) X .018" 150 bar
HEMPEL'S ZP ALKYD PRIMER 12090 f/c 100 Yellow 2022S 75 40 12.3 X (X) X .018" 150 bar
HEMPALIN ENAMEL 52140 f/c 100 To Be Advised T.B.A 75 35 13.1 (X) (X) X .018" 150 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 125 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPEL'S ZP ALKYD PRIMER 12090 2022S 49 2h 38 08230 5
HEMPEL'S ZP ALKYD PRIMER 12090 2022S 49 2h 38 08230 5
HEMPALIN ENAMEL 52140 T.B.A 46 6h 38 08230 5
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 30
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove prior to full spray coat application.
salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa NOTE :
2½ according to ISO 8501-1:2007. Dedust and clean surface prior to painting. 1). This Painting Specification is made based on client's specification.
2). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPATEX HI-BUILD 46330 f/c 100 Red 50630 125 50 8.4 (X) X 0.0 bar
HEMPATEX HI-BUILD 46330 f/c 100 To Be Advised T.B.A 125 50 8.4 (X) X 0.0 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 100 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time and recoating intervals.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPATEX HI-BUILD 46330 50630 42 8h 32 08080
HEMPATEX HI-BUILD 46330 T.B.A 42 8h 32 08080
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 32
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove prior to full spray coat application.
salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa NOTE :
2 according to ISO 8501-1:2007. Dedust and clean surface prior to painting. 1). This Painting Specification is made based on client's specification.
2). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPINOL HB 10270 f/c 100 Black 19990 600 375 1.7 X X 0.021 - 0.023200 bar
HEMPINOL HB 10270 f/c 100 Black 19990 600 375 1.7 X X 0.021 - 0.023200 bar
HEMPINOL HB 10270 f/c 100 Black 19990 650 400 1.6 X X 0.021 - 0.023200 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 1150 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time and recoating intervals.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPINOL HB 10270 19990 62 24 h 38 08080 85
HEMPINOL HB 10270 19990 62 24 h 38 08080 85
HEMPINOL HB 10270 19990 62 24 h 38 08080 85
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 34
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Hempel's Galvosil 15780 must be fully cured prior to application of the 2nd coat.
water rinsing. Salts and other contamination to be removed by high pressure fresh water Approximate curing time is 24 hours at 20 deg C (75% RH). In case of very low humidity,
hosing. When the surface is dry: abrasive blast to Sa. 2½ according to ISO 8501-1:2007 hose down surface with fresh water 1-2 hours after application to ensure curing of 15780.
with a surface profile corresponding to Rugotest No. 3 BN 10, Keane-Tator Comparator Continuously wet the surface until full curing is completed.
Disc, 3.0 G/S, or ISO Comparator Medium (G). Dedust and clean surface prior to
painting. Check curing condition by rubbing with piece of cloth soaked with Thinner 08700 (ASTM
D4752-03 Solvent-Rub Test).
Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush Apply mist coat of 56910 first on cured primer (15780) prior to full coat spray application
prior to full spray coat application. to avoid pinholes and minimise popping.
NOTE :
HEMPEL'S GALVOSIL 15780 f/c 100 Metal grey 19840 75 50 12.4 X X .019"-.023" 100 bar
HEMPEL'S SILICONE ALUMINIUM 56910 f/c 100 Light alu 19000 75 25 14.0 (X) X .017" 125 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 75 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time and recoating intervals.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPEL'S GALVOSIL 15780 19840 62 97170 8:2 4h 30 min 14 08700 0
HEMPEL'S SILICONE ALUMINIUM 56910 19000 35 2h 25 08080
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 36
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove prior to full spray coat application.
salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa NOTE :
2½ according to ISO 8501-1:2007. Dedust and clean surface prior to painting. 1). This Painting Specification is made based on client's specification.
2). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPEL'S SILICONE ALUMINIUM 56910 f/c 100 Light alu 19000 75 25 14.0 (X) X .017" 125 bar
HEMPEL'S SILICONE ALUMINIUM 56910 f/c 100 Light alu 19000 75 25 14.0 (X) X .017" 125 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 50 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time and recoating intervals.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPEL'S SILICONE ALUMINIUM 56910 19000 35 2h 25 08080
HEMPEL'S SILICONE ALUMINIUM 56910 19000 35 2h 25 08080
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 38
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Salts and other contamination to be removed by high pressure fresh water prior to full spray coat application.
hosing. When the surface is dry: abrasive blast to Sa. 2½ according to ISO 8501-1:2007 NOTE :
with a surface profile corresponding to Rugotest No. 3 BN 10a, Keane-Tator Comparator 1). See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
Disc, 3.0 G/S, or ISO Comparator Medium (G). Dedust and clean surface prior to and recoating intervals. Please follow the minimum and maximum recoating time interval
painting. of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
VERSILINE CUI 56990 f/c 100 Aluminium 19360 225 150 4.7 (X) (X) X .019-.021'' 200 bar
VERSILINE CUI 56990 f/c 100 Aluminium 19360 225 150 4.7 (X) (X) X .019-.021'' 200 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 300 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
VERSILINE CUI 56990 19360 70 45 min 29 08080 10
VERSILINE CUI 56990 19360 70 45 min 29 08080 10
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 40
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove prior to full spray coat application.
salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa NOTE :
2½ according to ISO 8501-1:2007. Dedust and clean surface prior to painting. 1). The non-skid aggregate HEMPEL ANTI-SLINT 67500 shall be springkled on top of the
2nd Intermediate coat while it is still wet. When dry, remove surplus aggregate and apply
the topcoat.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR HB PRIMER 17300 f/c 100 Yellow 21780 100 50 11.2 X X .021" 175 bar
HEMPADUR MASTIC 45881 f/c 100 To Be Advised T.B.A 125 100 8.0 (X) X .017"-.023" 250 bar
HEMPADUR MASTIC 45881 f/c 100 Grey 13600 125 100 8.0 (X) X .017"-.023" 250 bar
HEMPADUR MASTIC 45881 f/c 100 To Be Advised T.B.A 125 100 8.0 (X) X .017"-.023" 250 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 350 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time and recoating intervals.
When the interval is denoted "Extended", the coated structure can possibly be overcoated even after longer periods. This will depend on the actual exposure conditions, such as
limited exposure to sun, and on the condition and cleanliness of the paint surface. The evaluation of the specific situation must be based on local experience, contact HEMPEL for
advice.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR HB PRIMER 17300 21780 56 95010 5:1 8h 2h 26 08450
HEMPADUR MASTIC 45881 T.B.A 80 95881 3:1 1 h 30 min 3h 39 08450 15
HEMPADUR MASTIC 45881 13600 80 95881 3:1 1 h 30 min 3h 39 08450 15
HEMPADUR MASTIC 45881 T.B.A 80 95881 3:1 1 h 30 min 3h 39 08450 15
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 42
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution by thorough fresh water Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
rinsing. Salts and other contamination to be removed by high pressure fresh water prior to full spray coat application.
hosing. When the surface is dry: abrasive blast to Sa. 2½ according to ISO 8501-1:2007 NOTE :
with a surface profile corresponding to Rugotest No. 3 BN 10, Keane-Tator Comparator 1). This Painting Specification is made based on client's specification.
Disc, 3.0 G/S, or ISO Comparator Medium (G). Dedust and clean surface prior to 2). Consult the Product Data Sheets for further technical information and clarification.
painting.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPEL'S GALVOSIL 15780 f/c 100 Metal grey 19840 100 65 9.5 X X .019"-.023" 100 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 65 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time and recoating intervals.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPEL'S GALVOSIL 15780 19840 62 97170 8:2 4h 30 min 14 08700 0
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 44
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove prior to full spray coat application.
salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa NOTE :
2½ according to ISO 8501-1:2007 with a surface profile corresponding to Rugotest No. 3 1). This Painting Specification is made based on client's specification.
BN 11a, Keane-Tator Comparator Disc, 5.5 G/S, or ISO Comparator Coarse (G). Dedust 2). Consult the Product Data Sheets for further technical information and clarification.
and clean surface prior to painting.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR MULTI-MIL 85490 f/c 100 Green 41970 2500 2500 0.4 0.0 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 2500 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time and recoating intervals.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR MULTI-MIL 85490 41970 100 97490 1:1 2h 8h 5
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 46
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove prior to full spray coat application.
salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa NOTE :
2½ according to ISO 8501-1:2007 with a surface profile corresponding to Rugotest No. 3 1). This Painting Specification is made based on client's specification.
BN 11a, Keane-Tator Comparator Disc, 5.5 G/S, or ISO Comparator Coarse (G). Dedust 2). Consult the Product Data Sheets for further technical information and clarification.
and clean surface prior to painting.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR SPRAY-GUARD 85550 f/c 100 Grey-green 41690 2500 2500 0.4 X 0.0 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 2500 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time and recoating intervals.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR SPRAY-GUARD 85550 41690 100 95690 5.3 : 1 1h 8h 60 10 85
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 48
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Salts and other contamination to be removed by high pressure fresh water prior to full spray coat application.
hosing. When the surface is dry: abrasive blast to Sa. 2½ according to ISO 8501-1:2007 NOTE :
with a surface profile corresponding to Rugotest No. 3 BN 10, Keane-Tator Comparator 1).See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
Disc, 3.0 G/S, or ISO Comparator Medium (G). Dedust and clean surface prior to and recoating intervals. Please follow the minimum and maximum recoating time interval
painting. of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR MULTI-STRENGTH GF 35870 f/c 100 Yellow 27230 875 750 1.2 X .023"-.027" 250 bar
HEMPADUR MULTI-STRENGTH GF 35870 f/c 100 Grey 17380 875 750 1.2 X .023"-.027" 250 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 1500 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR MULTI-STRENGTH GF 27230 87 98870 3:1 1h 6h 35 08450 5
35870
HEMPADUR MULTI-STRENGTH GF 17380 87 98870 3:1 1h 6h 35 08450 5
35870
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 50
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove prior to full spray coat application. Use 05500 + 67500 anti-slint powder as caulking
salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa compound to fill-up plate overlaps, seams, welds and chime area (where the shell wall
2½ according to ISO 8501-1:2007 with a surface profile corresponding to Rugotest No. 3 joins with the tank floor) after primer application.
BN 11a, Keane-Tator Comparator Disc, 5.5 G/S, or ISO Comparator Coarse (G). Dedust NOTE :
and clean surface prior to painting. 1).See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
and recoating intervals. Please follow the minimum and maximum recoating time interval
of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR 15590 f/c 100 Red brown 56880 100 40 11.0 (X) X .017"-.019" 150 bar
HEMPEL'S EPOXY RESIN 05500 f/c 100 Transparent 00000 500 500 2.0 0.0 bar
HEMPEL'S GLASS FIBRE MATT 690SA f/c 100 Transparent 00000 NAN 0 NAN 0.0 bar
HEMPEL'S EPOXY RESIN 05500 f/c 100 Transparent 00000 500 500 2.0 0.0 bar
HEMPEL'S G/F SURFACING TISSUE 691SA f/c 100 Transparent 00000 NAN 0 NAN 0.0 bar
HEMPEL'S EPOXY RESIN 05500 f/c 100 Transparent 00000 300 300 3.3 0.0 bar
HEMPEL'S EPOXY RESIN 05500 f/c 100 Transparent 00000 300 300 3.3 0.0 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 1640 X: Recommended (X): Possible
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 52
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
When the full glassfibre-epoxy resin system is through dry (after approx. 24 hours at 20 C), the surface should be sanded down with emery paper (grit 240-320) to remove any
protruding glass fibres and imbedded or fairly adhering contamination.
After sanding, clean surface thoroughly (for dust) by means of an industrial vacuum cleaner. Apply one seal coat of Hempel's Epoxy Resin 05500 at a wet film thickness of 300
microns.
Allow the last coat of Hempel's Epoxy Resin 05500 to cure for 7 days (at 20 C) before putting the tank into service.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR 15590 56880 44 95100 15 : 4 2h 3h 26 08450 5 80
HEMPEL'S EPOXY RESIN 05500 00000 100 98500 65 : 35 66 10
HEMPEL'S GLASS FIBRE MATT 690SA 00000 0
HEMPEL'S EPOXY RESIN 05500 00000 100 98500 65 : 35 66 10
HEMPEL'S G/F SURFACING TISSUE 00000 0
691SA
HEMPEL'S EPOXY RESIN 05500 00000 100 98500 65 : 35 66 10
HEMPEL'S EPOXY RESIN 05500 00000 100 98500 65 : 35 66 10
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 53
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove prior to full spray coat application. Use 35890 + 67500 anti-slint powder as caulking
salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa compound on chime areas, weld seams, corners prior to sprayfibre application
2½ according to ISO 8501-1:2007 with a surface profile corresponding to Rugotest No. 3 NOTE :
BN 11a, Keane-Tator Comparator Disc, 5.5 G/S, or ISO Comparator Coarse (G). Dedust 1). The total DFT of 1250 microns is the sum of HEMPADUR SPRAY FIBRE 35890 +
and clean surface prior to painting. HEMPEL GLASS FIBRE ROVING 689SA
2).See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
and recoating intervals. Please follow the minimum and maximum recoating time interval
of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
3). This Painting Specification is made based on client's specification.
4). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR 15590 f/c 100 Red brown 56880 100 40 11.0 (X) X .017"-.019" 150 bar
HEMPADUR SPRAY FIBRE 35890 f/c 100 Brown 60090 1250 1250 0.8 X 0.0 bar
HEMPEL GLASS FIBRE ROVING 689SA f/c 100 Transparent 00000 0 0 INF 0 0.0 bar
HEMPADUR SPRAY FIBRE 35890 f/c 100 Brown 60090 350 350 2.9 X 0.0 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 1640 X: Recommended (X): Possible
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 55
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR 15590 56880 44 95100 15 : 4 2h 3h 26 08450 5 80
HEMPADUR SPRAY FIBRE 35890 60090 100 95890 2:1 45 min 8h 93
HEMPEL GLASS FIBRE ROVING 689SA 00000 100
HEMPADUR SPRAY FIBRE 35890 60090 100 95890 2:1 45 min 8h 93
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 56
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Entire area to be (high pressure) fresh water cleaned in order to remove prior to full spray coat application.
salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa NOTE :
2½ according to ISO 8501-1:2007. Dedust and clean surface prior to painting. 1).See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
and recoating intervals. Please follow the minimum and maximum recoating time interval
of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specificaiton.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR 45070 f/c 100 Off white 11630 200 150 4.8 (X) (X) .021"-.023" 250 bar
HEMPADUR 45070 f/c 100 To Be Advised T.B.A 200 150 4.8 (X) (X) .021"-.023" 250 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 300 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR 45070 11630 72 97070 4:1 3h 7h 35 08450 0
HEMPADUR 45070 T.B.A 72 97070 4:1 3h 7h 35 08450 0
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 58
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Salts and other contamination to be removed by high pressure fresh water prior to full spray coat application.
hosing. When the surface is dry: abrasive blast to Sa. 2½ according to ISO 8501-1:2007 NOTE :
with a surface profile corresponding to Rugotest No. 3 BN 9a to BN 10, Keane-Tator 1). This Painting Specification is made based on client's specification.
Comparator Disc, 2.0 G/S, or ISO Comparator Medium (G). Dedust and clean surface 2). Consult the Product Data Sheets for further technical information and clarification.
prior to painting.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR MASTIC 45881 f/c 100 Grey 17380 200 150 5.3 (X) X .017"-.023" 250 bar
HEMPADUR MASTIC 45881 f/c 100 To Be Advised T.B.A 200 150 5.3 (X) X .017"-.023" 250 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 300 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time and recoating intervals.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR MASTIC 45881 17380 80 95881 3:1 1 h 30 min 3h 39 08450 15
HEMPADUR MASTIC 45881 T.B.A 80 95881 3:1 1 h 30 min 3h 39 08450 15
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 60
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Salts and other contamination to be removed by high pressure fresh water prior to full spray coat application.
hosing. When the surface is dry: abrasive blast to Sa. 2½ according to ISO 8501-1:2007 NOTE :
with a surface profile corresponding to Rugotest No. 3 BN 9a to BN 10, Keane-Tator 1).See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time
Comparator Disc, 2.0 G/S, or ISO Comparator Medium (G). Dedust and clean surface and recoating intervals. Please follow the minimum and maximum recoating time interval
prior to painting. of each product given below. If maximum recoating interval is exceeded, roughening of
the surface by sweepblasting or sanding is necessary to obtain good intercoat adhesion.
2). This Painting Specification is made based on client's specification.
3). Consult the Product Data Sheets for further technical information and clarification.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR MASTIC 45881 f/c 100 Yellow 20300 150 125 6.4 (X) X .017"-.023" 250 bar
HEMPADUR MASTIC 45881 f/c 100 Grey 17380 150 125 6.4 (X) X .017"-.023" 250 bar
HEMPATHANE TOPCOAT 55210 f/c 100 To Be Advised T.B.A 75 40 12.5 (X) (X) X .017"-.019" 150 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 290 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR MASTIC 45881 20300 80 95881 3:1 1 h 30 min 3h 39 08450 15
HEMPADUR MASTIC 45881 17380 80 95881 3:1 1 h 30 min 3h 39 08450 15
HEMPATHANE TOPCOAT 55210 T.B.A 50 95370 7:1 4h 8h 33 08080 -10
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 62
Specification sheet
Hempel (Saudi Arabia) W.L.L.
Surface preparation:
Oil and grease etc. to be removed by strong detergent solution followed by thorough fresh Stripe coat all hidden difficult areas : weld seams, edges, corners, etc. using paint brush
water rinsing. Salts and other contamination to be removed by high pressure fresh water prior to full spray coat application.
hosing. When the surface is dry: abrasive blast to Sa. 2½ according to ISO 8501-1:2007 NOTE :
with a surface profile corresponding to Rugotest No. 3 BN 10b, Keane-Tator Comparator 1). This Painting Specification is made based on client's specification.
Disc, 3.0 G/S, or ISO Comparator Medium (G). Dedust and clean surface prior to 2). Consult the Product Data Sheets for further technical information and clarification.
painting.
Film thickness Theoretical spreading Application methods Recommended
Treated area Shade no. (micron) rate Roller Nozzle Nozzle
Product name (including quality number) % Colour Wet Dry (sqm/ltr) Brush Spray orifice pressure
HEMPADUR XP 87550 f/c 100 Brown-aluminium 59700 675 600 1.5 X 0.021"-0.023"250 bar
t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 600 X: Recommended (X): Possible
Remarks:
Normal good painting practice must be followed throughout the entire painting procedure.
See product data sheet and / or APPLICATION INSTRUCTIONS regarding drying time and recoating intervals.
Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions
Volume Curing volume point Min. Temp. Max. RH%
Shade no. solids % agent 20°C 20°C °C Thinner °C
HEMPADUR XP 87550 59700 90 98550 4:1 1 h 30 min 5h 14 10 85
The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the
best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not
guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any and
all claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.
Hempel's PreSale System 2.6.17 (Build 929) User name: Jeffrey Papa Quality Code:
Printed at: 16.03.2017 13:28 Department name: TSD Environment : Severe
Created/Last modified: 16.03.2017 13:27 SAJAP1527N Page: 64
Product Data
HEMPEL'S ZP ALKYD PRIMER 12090
Description: HEMPEL’S ZP ALKYD PRIMER 12090 is a relatively quick-drying, zinc phosphate primer, based on
long oil alkyd and urethane alkyd.
Recommended use: General purpose primer for HEMPALIN systems for protection of steel in mild to medium atmospheric
corrosive environments.
Service temperatures: Maximum, dry exposure only: 120°C/248°F
Availability: Not included in Group Assortment. Availability subject to special agreement.
PHYSICAL CONSTANTS:
Shade nos/Colours: 50410/ Red.
Finish: Flat
Volume solids, %: 49 ± 1
Theoretical spreading rate: 12.3 m2/l [493.2 sq.ft./US gallon] - 40 micron/1.6 mils
Flash point: 38 °C [100.4 °F]
Specific gravity: 1.3 kg/litre [10.7 lbs/US gallon]
Dry to touch: 2 - 4 approx. hour(s) 20°C/68°F
VOC content: 407 g/l [3.4 lbs/US gallon]
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Application method: Airless spray / Air spray / Brush (touch up)
Thinner (max.vol.): 08230(5%)/08230(5%)/08230(5%)
Nozzle orifice: 0.018 "
Nozzle pressure: 150 bar [2175 psi]
Cleaning of tools: HEMPEL'S THINNER 08230
Indicated film thickness, dry: 40 micron [1.6 mils]
Indicated film thickness, wet: 75 micron [3 mils]
Recoat interval, min: According to specification.
Recoat interval, max: According to specification.
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
SURFACE PREPARATION: New steel: Abrasive blasting to Sa 2 (ISO 8501-1:1988) is recommended. For temporary protection, if
required, use a suitable shopprimer. All damage of shopprimer and contamination from storage and
fabrication should be thoroughly cleaned prior to final painting. For repair and touch-up use: HEMPEL’S
ZP ALKYD PRIMER 12090.
Maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other
contaminants by high pressure fresh water cleaning. Remove all rust and loose material by abrasive
blasting or power tool cleaning. Dust off residues. Touch up bare spots to full film thickness.
APPLICATION CONDITIONS: As dictated by normal good painting practice. In confined spaces provide adequate ventilation during
application and drying.
SUBSEQUENT COAT: According to specification. Recommended systems are: white spirit based alkyds.
REMARKS:
Film thicknesses/thinning: May be specified in another film thickness than indicated depending on purpose and area of use. This
will alter spreading rate and may influence drying time and recoating interval. Normal range dry is: 30-
50 micron/1.2-2 mils.
Recoating note: If the maximum recoating interval is exceeded, roughening of the surface is necessary to ensure
intercoat adhesion. Before recoating after exposure in contaminated environment, clean surface
thoroughly with high pressure fresh water hosing and allow drying.
Recoating intervals: Recoating intervals related to later conditions of exposure: 40 micron/1.6 mils dry film thickness of
HEMPEL’S ZP ALKYD PRIMER 12090.
Nota: HEMPEL'S ZP ALKYD PRIMER 12090 For professional use only.
ISSUED BY: HEMPEL A/S 1209050410
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Version, mixed product: 15590
Mixing ratio: BASE 15599: CURING AGENT 95100
15 : 4 by volume
Application method: Airless spray / Air spray
Thinner (max.vol.): 08450 (5%) / 08450 (15%)
Pot life: 2 hour(s) 20°C/68°F
Nozzle orifice: 0.017 - 0.019 "
Nozzle pressure: 150 bar [2175 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S TOOL CLEANER 99610
Indicated film thickness, dry: 40 micron [1.6 mils]
Indicated film thickness, wet: 100 micron [4 mils]
Overcoat interval, min: see REMARKS overleaf
Overcoat interval, max: see REMARKS overleaf
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
SURFACE PREPARATION: New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other
contaminants by high pressure fresh water cleaning. Abrasive blasting to Sa 2½-3 (ISO 8501-1:2007)
depending on area of use. Minimum surface profile corresponding to Rugotest No. 3, BN11a, Keane-
Tator Comparator, 5.5 G/S, or ISO Comparator Coarse (G) - or as per specification for the subsequent
coat(s). After blasting, clean the surface carefully from abrasives and dust.
Repair and maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove
salts and other contaminants by high pressure fresh water cleaning. On pit-corroded surfaces,
excessive amounts of salt residues may call for high pressure water jetting, wet abrasive blasting or,
alternatively, dry abrasive blasting, high pressure fresh water hosting, drying, and finally dry abrasive
blasting again.
APPLICATION CONDITIONS: Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.
Minimum temperature for application is 5°C/41°F, preferably above 10°C/50°F. Relative humidity
maximum 80 %, preferably below 60%.
The temperature of the paint itself should be: Between 15°C (59°F) and 25°C (77°F).
In confined spaces provide adequate ventilation during application and drying.
PRECEDING COAT: None.
SUBSEQUENT COAT: Recommended systems are: HEMPADUR MULTI-STRENGTH 35530, HEMPADUR MULTI-
STRENGTH 45751.
HEMPADUR 15590 can be used as a blast primer.
REMARKS:
Film thicknesses/thinning: May be specified in another film thickness than indicated depending on purpose and area of use. This
will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:
30-50 micron/1.2-2 mils.
Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high
pressure fresh water hosing and allow drying.
Overcoating note: The coating is to be applied in a dry film thickness as near as possible to the specified: 40 micron.
Film formation of each coat has to be of good quality, free from defects such as pinholes and without
any dry spray.
Drying and curing conditions have to be according to APPLICATION CONDITIONS until full curing has
been obtained.
No kind of surface contamination must exist except loose dust, abrasives, loose dry-spray, which is
possible to remove by vacuum cleaning before overcoating.
The surface MUST be completely clean before overcoating. The coating is to be checked carefully and
should have no patchy, whitish, and/or greasy formation, which can hinder adhesion of the subsequent
coat.
Exudation of the curing agent causes the mentioned patchy, whitish, and/or greasy formation, which
will take place if the product is applied at low temperatures without proper induction time and/or if the
coating is exposed to water (rain, condensation) during drying and curing.
Overcoating intervals: Overcoating intervals: According to specification.
The stated minimum overcoating interval may be halved for areas not intended for water immersion.
Depending on actual local conditions, extended maximum overcoating interval may apply. Contact
HEMPEL for more information. If the maximum over coating interval is exceeded, roughening of the
surface is necessary to ensure intercoat adhesion. Before overcoating after exposure in contaminated
environment, clean the surface thoroughly by high pressure water cleaning and allow drying. The
product will resist a hosing down of the surface 8 hours after application at a steel temperature of
20°C/68°F.
Note: HEMPADUR 15590 For professional use only.
ISSUED BY: HEMPEL A/S 1559056880
X Move PDS Disclaimer to Second page
This Product Data Sheet supersedes those previously issued.
For explanations, definitions and scope, see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations given in this data sheet
represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions
of any intended use of the Products herein must be determined exclusively by the Buyer and/or User.
The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed
in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said
GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise.
Product data are subject to change without notice and become void five years from the date of issue.
Hempel's Zinc metal pigment 97170 is in full compliance with ISO 3549 and ASTM D520 type I,
Hempel's Zinc metal pigment 97140 is additionally in compliance with ASTM D520 type II.
Recommended use: As a general purpose rust-preventing primer in paint systems for long-life protection of steel exposed to
moderately to severely corrosive environment. In compliance with SSPC-Paint 20, type 1, level 2.
Service temperature: Resistant to permanent (non-cyclic) dry temperatures as well as occasionally dry peak temperatures up
to maximum: 500°C/932°F.
It is of advantage to apply a topcoat of HEMPEL'S SILICONE ALUMINIUM 56914 in case of service
temperatures above: 400°C/752°F.
Resistant to cyclic dry temperatures up to 400°C/752°F.
Availability: Part of Group Assortment. Local availability subject to confirmation.
PHYSICAL CONSTANTS:
Shade nos/Colours: 19840 / Metal grey
Finish: Flat
Volume solids, %: 62 ± 1
Theoretical spreading rate: 12.4 m2/l [497.2 sq.ft./US gallon] - 50 micron/2 mils
Flash point: 14 °C [57.2 °F]
Specific gravity: 2.4 kg/litre [20 lbs/US gallon]
Surface-dry: 15 minute(s) 20°C/68°F
Through-dry: 20 minute(s) 20°C/68°F
Fully cured: 16 approx. hour(s) 20°C/68°F (65% RH)
VOC content: 442 g/l [3.7 lbs/US gallon]
Shelf life: 6 months for the LIQUID and 3 years for HEMPEL'S ZINC METAL PIGMENT (stored in closed
container) (25°C/77°F) from time of production.
Shelf life is dependent on storage temperature. Shelf life is reduced at storage temperatures above
25°C/77°F. Do not store above 40°C/104°F. Shelf life is exceeded if the liquid is gelled or if the mixed
product forms gels before application.
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Version, mixed product: 15780
Mixing ratio: LIQUID 15789: HEMPEL’S ZINC METAL PIGMENT 97170/97140
4.1 : 5.9 by weight
(by volume - see REMARKS overleaf)
Application method: Airless spray / Air spray / Brush (touch up)
Thinner (max.vol.): [08700 (30%) and/or 0870M (30%) see REMARKS overleaf ]/ 08700 (50%) / 08700 (10%)
Pot life: 4 hour(s) 20°C/68°F
Nozzle orifice: 0.019 - 0.023 "
Nozzle pressure: 100 bar [1450 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S THINNER 08700
Indicated film thickness, dry: 50 micron [2 mils] see REMARKS overleaf
Indicated film thickness, wet: 75 micron [3 mils]
Overcoat interval, min: According to separate APPLICATION INSTRUCTIONS
Overcoat interval, max: According to separate APPLICATION INSTRUCTIONS
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
SURFACE PREPARATION: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants
by high pressure fresh water cleaning. Abrasive blasting with sharp abrasive to minimum Sa 2½ (ISO
8501-1:2007) with a surface profile equivalent to Rugotest No. 3, BN10, Keane-Tator Comparator, min.
3.0 G/S, or ISO Comparator rough Medium (G). In case of new steel to be exposed to no more than
medium aggressive (industrial) environment and without any extraordinary demands to lifetime, a
surface preparation degree of SSPC-SP6 may suffice.
See separate APPLICATION INSTRUCTIONS
APPLICATION CONDITIONS: The surface must be completely clean and dry at the time of application and its temperature must be
above the dew point to avoid condensation. At temperatures ranging from 0°C/32°F to 40°C/105°F,
curing needs minimum 50% relative humidity.
Curing is retarded at lower temperature and lower humidity.
See separate APPLICATION INSTRUCTIONS
SUBSEQUENT COAT: According to specification.
REMARKS:
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Version, mixed product: 17360
Mixing ratio: BASE 17369: CURING AGENT 97040
4 : 1 by volume
Application method: Airless spray / Air spray / Brush
Thinner (max.vol.): 08450 (5%) / 08450 (15%) / 08450 (5%) see REMARKS overleaf
Pot life: 2 hour(s) 20°C/68°F
Nozzle orifice: 0.017 - 0.021 "
Nozzle pressure: 150 bar [2175 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S TOOL CLEANER 99610
Indicated film thickness, dry: 50 micron [2 mils] see REMARKS overleaf
Indicated film thickness, wet: 75 micron [3 mils]
Overcoat interval, min: see REMARKS overleaf
Overcoat interval, max: see REMARKS overleaf
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
-
-
-
-
-
-
-
-
-
-
-
SURFACE PREPARATION: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants
by high pressure fresh water cleaning.
Abrasive blasting to Sa 2½ (ISO 8501-1:2007), SSPC-SP 10/ NACE No. 2, with a sharp-edged surface
profile corresponding to Rugotest No. 3, BN10a-b, Keane-Tator Comparator, 3.0 G/S, 2-3 S, or ISO
Comparator, Medium (G).
APPLICATION CONDITIONS: Use only where application and curing can proceed at temperatures above: -10°C/14°F. The
temperature of the surface must also be above these limits. The temperature of paint itself should be
15°C/59°F or above. Apply only on a dry and clean surface with a temperature above the dew point to
avoid condensation.
In confined spaces provide adequate ventilation during application and drying.
SUBSEQUENT COAT: According to specification.
REMARKS: Note: If used as anticorrosive protection under insulation of high temperature equipment it is very
important that NO moisture can penetrate during slow-down periods. This is to avoid the risk of "wet
corrosion" when the temperature rises.
VOC - EU Directive 2004/42/EC:
Not available.
Product As supplied 15 vol. % thinning Limit phase II, 2010
1736019830 310 g/l 392 g/l 500 g/l
For VOC of other shades, please refer to Safety Data Sheet.
Weathering/service temperatures: The natural tendency of epoxy coatings to chalk in outdoor exposure and to become more sensitive to
mechanical damage and chemical exposure at elevated temperatures is also reflected in this product.
Stirring: Before mixing with the curing agent stir the base thoroughly in order to redisperse any possible settling
after storage. After mixing it is equally important to maintain stirring to keep the wet paint as a
homogeneous mixture.
This is specifically important in case of a high level of thinning and/or long break in application, where
the risk of settlement of zinc particles is the highest.
Film thicknesses/thinning: May be specified in another film thickness than indicated depending on purpose and area of use. This
will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:
40-80 micron/1.6-3.2 mils. Thicknesses down to 15 micron/0.6 mils (extra thinning) and up to 80
micron/3.2 mils may be possible. This will alter spreading rate and may influence amount of thinning
necessary, drying time, and recoating interval.
(The dry film thickness range does not take into account the correction factors for rough surfaces as
listed in ISO 19840).
Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high
pressure fresh water hosing and allow drying.
Overcoating note: *Depending on actual local conditions, the long maximum overcoating intervals may vary.
Contact HEMPEL for more information.
A completely clean surface is mandatory to ensure intercoat adhesion, especially at long overcoating
intervals. Any dirt, oil, grease, and other foreign matter must be removed with suitable detergent
followed by (high pressure) fresh water cleaning. Salts to be removed by fresh water hosing. In addition,
scrubbing with a stiff brush may be necessary to remove zinc corrosion products (white rust). If the
maximum overcoating interval is exceeded, roughening of the surface is necessary to ensure intercoat
adhesion.
Note: HEMPADUR ZINC 17360 For professional use only.
ISSUED BY: HEMPEL A/S 1736019830
X Move PDS Disclaimer to Second page
This Product Data Sheet supersedes those previously issued.
For explanations, definitions and scope, see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations given in this data sheet
represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions
of any intended use of the Products herein must be determined exclusively by the Buyer and/or User.
The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed
in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said
GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise.
Product data are subject to change without notice and become void five years from the date of issue.
Description: HEMPEL'S COAL TAR EPOXY MASTIC 35670 is a high solids, high-build polyamide cured coal tar
epoxy coating with excellent resistance to sea water, crude oil, various soil chemicals and soil stress.
Recommended use: As a long-life protective coating on steel and concrete in severe corrosive environment, e.g., on
submerged surfaces, crude oil and slop tanks, ballast tanks, splash zones, sewage systems, etc.
Excellent resistance to chemical attack encountered on both steel and concrete including buried pipes.
Service temperature: Maximum, dry exposure only: 90°C/194°F
In water (no temperature gradient): 40°C/105°F
Other liquids: Contact HEMPEL
Certificates/Approvals: The product complies with ARAMCO Engineering Standard APCS-3. see REMARKS overleaf
Availability: Not included in Group Assortment. Availability subject to special agreement.
PHYSICAL CONSTANTS:
Shade nos/Colours: 19990*/ Black.
Finish: Semi-gloss
Volume solids, %: 92 ± 1
Theoretical spreading rate: 4.6 m2/l [184.5 sq.ft./US gallon] - 200 micron/8 mils
Flash point: 23 °C [73.4 °F]
Specific gravity: 1.5 kg/litre [12.2 lbs/US gallon]
Dry to touch: 8 - 10 approx. hour(s) 20°C/68°F
Fully cured: 7 day(s) , 20°C/68°F
VOC content: 127 g/l [1.1 lbs/US gallon]
- *other shades according to assortment list.
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Version, mixed product: 35670
Mixing ratio: BASE 35679: CURING AGENT 98670
4:1 by volume
Application method: Airless spray / Brush/Roller
Thinner (max.vol.): 08450 (5%) / 08450 (15%)
Pot life: 8 approx. hour(s) 20°C/68°F
Nozzle orifice: 0.021 - 0.023 "
Nozzle pressure: 250 bar [3625 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S TOOL CLEANER 99610
Indicated film thickness, dry: 200 - 300 micron [8 - 12 mils]
Indicated film thickness, wet: 225 - 325 micron [9 - 13 mils]
Overcoat interval, min: see REMARKS overleaf
Overcoat interval, max: see REMARKS overleaf
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
-
-
-
-
-
-
-
-
Film thicknesses/thinning: May be specified in another film thickness than indicated depending on purpose and area of use. This
will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:
200-350 micron/8-14 mils.
Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with
high pressure fresh water hosing and allow drying.
Overcoating intervals: For overcoating, HEMPATEX HI-BUILD 46330 can be used. It is to be applied within maximum 16
hours at a surface temperature of 20°C/68°F.
Note: HEMPEL'S COAL TAR EPOXY MASTIC 35670 Bleeding may occur into subsequent coat. This
effect is cosmetic only and has no influence on the protective properties.
For professional use only.
ISSUED BY: HEMPEL A/S
3567019990
X Move PDS Disclaimer to Second page
This Product Data Sheet supersedes those previously issued.
For explanations, definitions and scope, see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations
given in this data sheet represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy,
completeness or appropriateness under the actual conditions of any intended use of the Products herein must be determined exclusively by the Buyer
and/or User.
The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless
otherwise expressly agreed in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but
not limited to negligence, except as expressed in said GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising
from the use of the Products as recommended above, on the overleaf or otherwise. Product data are subject to change without notice and become void
five years from the date of issue.
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Version, mixed product: 35870
Mixing ratio: BASE 35879 : CURING AGENT 98870
3 : 1 by volume
Application method: Airless spray
Thinner (max.vol.): 08450 (5%)
Pot life: 1 hour(s) 20°C/68°F
Nozzle orifice: 0.023 - 0.027 " Reversible
Nozzle pressure: 250 bar [3625 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S TOOL CLEANER 99610
Indicated film thickness, dry: 350 micron [14 mils]
Indicated film thickness, wet: 400 micron [16 mils]
Overcoat interval, min: see REMARKS overleaf
Overcoat interval, max: see REMARKS overleaf
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
-
-
-
-
-
-
-
-
SURFACE PREPARATION: New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other
contaminants by high pressure fresh water cleaning. Abrasive blasting to near white metal Sa 2½ with
a surface profile corresponding to Rugotest No. 3, BN10, Keane-Tator Comparator 3.0 G/S, or ISO
Comparator Rough Medium (G). After blasting, clean the surface carefully from abrasives and dust.
Maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other
contaminants by high pressure fresh water cleaning. Remove all rust and loose material by wet or dry
abrasive blasting or power tool cleaning. Feather edges to sound and intact areas. After wet abrasive
blasting hose down the surface with fresh water and allow drying.
Touch up bare spots to full film thickness when the surface has become visually dry.
APPLICATION CONDITIONS: Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.
May be applied and will cure at temperatures down to 5°C/41°F. The temperature of the paint itself
should be above: 15°C/59°F. The best result is obtained at: 20-30°C/68-86°F. In confined spaces
provide adequate ventilation during application and drying.
PRECEDING COAT: None. If a blast primer is required, use: HEMPADUR 15590.
SUBSEQUENT COAT: None, or as per specification.
REMARKS:
Certificates/Approvals: The recognition as Abrasion Resistant Ice Coating by Lloyds Register applies to the product as well as
production site – at present the certificate is valid only for paint material produced at the following
Hempel factories: Hempel Paints Poland, Buk.
Colours/Colour stability: Light shades will have a tendency to yellow when exposed to sunshine and darken when exposed to
heat.
Weathering/service temperatures: The natural tendency of epoxy coatings to chalk in outdoor exposure and to become more sensitive to
mechanical damage and chemical exposure at elevated temperatures is also reflected in this product.
Application(s): The product may be immersed after 4 hours of initial curing at 20°C/68°F. Curing will proceed under
water. Early immersion may result in some discolouration. This does not affect the protective properties
of the product.
Application equipment: Standard airless heavy-duty spray equipment:
Recommended pump ratio: minimum 45:1
Pump output: 12 litres/minute (theoretical)
Spray hoses: max 15 metres/50 feet, 3/8'' internal diameter, max 3 metres/10 feet, 1/4'' internal
diameter
If longer spray hoses are necessary it is possible to add up to : 50 meters / 150 feet.
The high output capacity of the pump must be obtained. The ratio must be raised to:60:1.
Bigger spray nozzles will also call for increased pump size. A reversible nozzle is recommended.
Surge tank filter and tip filter should be removed.
Film thicknesses/thinning: May be specified in another film thickness than indicated depending on purpose and area of use. This
will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:
350-500 micron/14-20 mils
Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high
pressure fresh water hosing and allow drying.
APPLICATION DETAILS:
Version, mixed product: 35910
Mixing ratio: BASE 35919: CURING AGENT 99410
98:2 by volume
Application method: Airless spray / Brush / Roller
According to separate APPLICATION INSTRUCTIONS
Thinner (max.vol.): Do not dilute.
Pot life: 45 minute(s) 20°C/68°F. According to separate APPLICATION INSTRUCTIONS
Nozzle orifice: 0.03 - 0.06 " Reversible
Nozzle pressure: 275 bar [3987.5 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: According to separate APPLICATION INSTRUCTIONS. Recommended: HEMPEL'S THINNER 08960 .
Indicated film thickness, dry: 650 micron [26 mils]
Indicated film thickness, wet: 725 micron [29 mils] see REMARKS overleaf.
Overcoat interval, min: see REMARKS overleaf
Overcoat interval, max: see REMARKS overleaf
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
SURFACE PREPARATION: New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other
contaminants by high pressure fresh water cleaning. Abrasive blasting to min. Sa 2½ (ISO 8501-1:
2007). Minimum surface profile corresponding to Rugotest No. 3, BN11a, Keane-Tator Comparator, 5.5
G/S, or ISO Comparator Coarse (G) - or as per specification for the subsequent coat(s). After blasting,
clean the surface carefully from abrasives and dust.
Repair and maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove
salts and other contaminants by high pressure fresh water cleaning. On pit-corroded surfaces,
excessive amounts of salt residues may call for high pressure water jetting, wet abrasive blasting or,
alternatively, dry abrasive blasting, high pressure fresh water hosting, drying, and finally dry abrasive
blasting again.
Galvanized, Zinc primed steel etc.: Metallic zinc inhibits the curing process - the product is not
compatible with galvanized steel or other zinc coated substrates. Steel primed with zinc dust containing
pre-fabrication primers must be re-blasted to min. Sa 2½-3 to remove all traces of zinc.
APPLICATION CONDITIONS: Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.
Use only where application and curing can proceed at temperatures above: 10°C/50°F. Maximum
relative humidity: 85%. In-can temperature of the paint should preferably be below 25°C/77°F and
above 15°C/59°F. RETARDER 99190 should be added when application temperatures exceed
25°C/77°F. In confined spaces provide adequate ventilation during application and drying.
See separate APPLICATION INSTRUCTIONS
PRECEDING COAT: None.
SUBSEQUENT COAT: None. Recommended systems are: HEMPEL’S VINYL ESTER GF 35910
REMARKS:
Film thicknesses/thinning: May be specified in another film thickness than indicated depending on purpose and area of use. This
will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:.
500-1200 micron/20-48 mils per coat.
Volume solids, %: Theoretically, the product contains 100% solid. Depending on the application and curing conditions
some of the volatile reactants may evaporate. Furthermore, the curing process is accompanied by a
contraction.
These two factors result in a “theoretical” volume solids of 85% and a spreading rate of 1.3 m²/l at 650
micron (53 sq.ft./US gallon).
By unfavourable application conditions, higher losses may result in a practical spreading rate of
approximately 1.2 m²/l at 650 micron (49 sq.ft./US gallon).
Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high
pressure fresh water hosing and allow drying.
Description: HEMPADUR 45070 is a two-component, high-build, polyamine cured epoxy paint which cures to a
coating with good wetting properties and excellent resistance to sewater and crude oil.
Recommended use: As a selfpriming repair and maintenance coating for ballast tanks and void spaces. Suitable for
application down to 0°C/32°F.
Service temperature: Maximum, dry exposure only: 90°C/194°F
Maximum, in oil: 60°C/140°F
In water (max temperature gradient 10°C/18°F): 40°C/104°F
Certificates/Approvals: Classified B1 by DNV, Norway.
Approved by Lloyd's Register of Shipping as a corrosion control coating.
Approved as a ballast tank coating by Germanischer Lloyd, Germany.
Accepted as a corrosion control coating by Maritime Register of Shipping, Russia.
Availability: Not included in Group Assortment. Availability subject to special agreement.
PHYSICAL CONSTANTS:
Shade nos/Colours: 12170*/ Grey.
Finish: Flat
Volume solids, %: 72 ± 1
Theoretical spreading rate: 4.8 m2/l [192.5 sq.ft./US gallon] - 150 micron/6 mils
Flash point: 35 °C [95 °F]
Specific gravity: 1.3 kg/litre [11.1 lbs/US gallon]
Dry to touch: 7 - 8 approx. hour(s) 20°C/68°F
Fully cured: 7 day(s) (approx.) , 20°C/68°F
VOC content: 271 g/l [2.2 lbs/US gallon]
- *other shades according to assortment list.
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Version, mixed product: 45070
Mixing ratio: BASE 45079: CURING AGENT 97070
4:1 by volume
Application method: Airless spray / Brush (touch up)
Thinner (max.vol.): 08450 (5%) / 08450 (5%)
Pot life: 3 approx. hour(s) 20°C/68°F
Nozzle orifice: 0.021 - 0.023 "
Nozzle pressure: 250 bar [3625 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S TOOL CLEANER 99610
Indicated film thickness, dry: 150 micron [6 mils]
Indicated film thickness, wet: 200 micron [8 mils]
Overcoat interval, min: According to specification.
Overcoat interval, max: According to specification.
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
Colours/Colour stability: Has a tendency to yellow after application. This will have no influence on the performance.
Film thicknesses/thinning: May be specified in another film thickness than indicated depending on purpose and area of use. This
will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:
150-200 micron/6-8 mils.
Curing agent: The CURING AGENT will become darker during storage. This will result in a darker and more
yellowish shade. The colour change will have no influence on the performance.
Overcoating intervals: Overcoating intervals related to later conditions of exposure: (150 micron/ 6 mils dry film thickness).
Minimum - Maximum 3-90 days at a steel temperature of 0°C/32°F; Minimum - Maximum 1 - 60 days
at a steel temperature of 10°C/50°F; Minimum - Maximum 0.5 - 30 days at a steel temperature of
20°C/68°F.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly by high
pressure water cleaning and allow drying.
If the maximum overcoating interval is exceeded, roughening of the surface is necessary to ensure
intercoat adhesion.
Note: HEMPADUR 45070 For professional use only.
ISSUED BY: HEMPEL A/S 4507012170
Tested for non-contamination of grain cargo at the Newcastle Occupational Health & Hygiene, Great
Britain.
Approved as a low flame spread material when used as part of a predefined paint system. Please refer
to “Declaration of Conformity” on www.Hempel.com for further details.
Complies with EU Directive 2004/42/EC: subcategory j.
Availability: Part of Group Assortment. Local availability subject to confirmation.
PHYSICAL CONSTANTS:
Shade nos/Colours: 12170* / Grey. (see REMARKS overleaf)
Finish: Semi-gloss
Volume solids, %: 80 ± 1
Theoretical spreading rate: 6.4 m2/l [256.6 sq.ft./US gallon] - 125 micron/5 mils
Flash point: 35 °C [95 °F]
Specific gravity: 1.5 kg/litre [12.1 lbs/US gallon]
Dry to touch: 3 hour(s) 30°C/86°F
Fully cured: 5 day(s) 30°C/86°F
VOC content: 218 g/l [1.8 lbs/US gallon]
Shelf life: 3 years for BASE and 3 years (25°C/77°F) for CURING AGENT from time of production.
- *Wide range of colours available via Hempel's MULTI-TINT system.
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Version, mixed product: 45881
Mixing ratio: BASE 45889: CURING AGENT 95881
3 : 1 by volume
Application method: Airless spray / Brush
Thinner (max.vol.): < 5% HEMPEL'S THINNER 08450, depending on purpose (see REMARKS overleaf)
Pot life (Airless spray): 1.5 hour(s) 30°C/86°F
Pot life (Brush): 2 hour(s) 30°C/86°F
Nozzle orifice: 0.017 - 0.023 " According to separate APPLICATION INSTRUCTIONS
Nozzle pressure: 250 bar [3625 psi]
Cleaning of tools: HEMPEL'S TOOL CLEANER 99610
Indicated film thickness, dry: 125 micron [5 mils] see REMARKS overleaf
Indicated film thickness, wet: 150 micron [6 mils]
Overcoat interval, min: see REMARKS overleaf
Overcoat interval, max: see REMARKS overleaf
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
-
-
-
-
-
-
SURFACE PREPARATION: New steel: Abrasive blasting to minimum Sa 2½ (ISO 8501-1:2007) with a surface profile
corresponding to Rugotest No. 3, N9a to N10, preferably BN9a to BN10, Keane-Tator Comparator, 2.0
G/S or ISO Comparator, Medium (G).
Zinc silicate painted or spray-metallized surfaces: Remove oil and grease, etc. with suitable
detergent. Remove salt and other contaminants by (high pressure) fresh water cleaning. Zinc salts
(white rust) must be removed by high pressure hosing combined with rubbing with a stiff nylon brush if
necessary. It is recommended to recoat spray-metallized surfaces as soon as possible to avoid
possible contamination.
Concrete: Remove slip agent and other possible contaminants by emulsion washing followed by high
pressure hosing with fresh water. Remove scum layer and loose matter to a hard, rough and uniform
surface, preferably by abrasive blasting, possibly by other mechanical treatment or acid etching. Seal
surface with suitable sealer, as per relevant painting specification.
Repair and maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove
salts and other contaminants by high pressure fresh water cleaning. Clean damaged areas thoroughly
by power tool cleaning to minimum St 2 (spot-repairs) or by abrasive blasting to min. Sa 2, preferably to
Sa 2½ (ISO 8501-1:1988). Improved surface preparation will improve the performance of the product.
As an alternative to dry cleaning, water jetting to sound, well adhering coat and/or to steel. Intact coat
must appear with roughened surface after the water jetting. By water jetting to steel, cleanliness shall
be: Wa 2 -Wa 2½ (atmospheric exposure) / minimum Wa 2½ (immersion) (ISO 8501-4:2006). Feather
edges to sound and intact areas. Dust off residues. Touch up to full film thickness. On pit-corroded
surfaces, excessive amounts of salt residues may call for high pressure water jetting, wet abrasive
blasting or, alternatively, dry abrasive blasting, high pressure fresh water hosting, drying, and finally dry
abrasive blasting again.
APPLICATION CONDITIONS: Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.
Use only where application and curing can proceed at temperatures above: 15°C/59°F.
The temperature of paint itself should be 15°C/59°F or above. In confined spaces provide adequate
ventilation during application and drying.
PRECEDING COAT: None, or as per specification.
SUBSEQUENT COAT: None, or as per specification.
REMARKS:
VOC - EU Directive 2004/42/EC:
Not available.
Product As supplied 5 vol. % thinning Limit phase II, 2010
4588112170 218 g/l 250 g/l 500 g/l
For VOC of other shades, please refer to Safety Data Sheet.
Weathering/service temperatures: The natural tendency of epoxy coatings to chalk in outdoor exposure and to become more sensitive to
mechanical damage and chemical exposure at elevated temperatures is also reflected in this product.
Application(s): Application onto zinc silicate or spray-metallized surfaces (thinning): It is recommended to apply the
paint by using a "mist-coat" procedure provided the paint temperature is approximately above:
20°C/68°F. A thin, undiluted coat is applied (the mist coat) and after a few minutes, a second coat is
applied in the full specified film thickness. If the paint temperature is below: 20°C/68°F, thinning (max
15%) may be required.
Film thicknesses/thinning: May be specified in another film thickness than indicated depending on purpose and area of use. This
will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:
100-200 micron/4-8 mils. May be specified in lower film thickness for which purpose additional thinning
is required, please see separate APPLICATION INSTRUCTIONS. Avoid application of excessive
film thicknesses.
Shades: The product is also available in a Micaceous Iron Oxide (MIO) pigmented shade (Shade no. 12430 –
reddish grey).
This product is available in several aluminium pigmented shades with different volume solids content.
Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high
pressure fresh water hosing and allow drying.
Description: HEMPATEX HI-BUILD 46330 is based on chlorinated rubber. Physically drying. Resistant to salt water,
splashes of mineral oils, aliphatic solvents and a wide range of chemicals, but not to animal and
vegetable oils or aromatic solvents.
Recommended use: Selfprimed, or as an intermediate or finishing coat on steel structures in moderately to severely
corrosive environment, including permanently submerged surfaces.
Service temperature: Maximum, dry exposure only: 80°C/176°F see REMARKS overleaf
Availability: Part of Group Assortment. Local availability subject to confirmation.
PHYSICAL CONSTANTS:
Shade nos/Colours: 11480/ Grey.
Finish: Flat
Volume solids, %: 42 ± 1
Theoretical spreading rate: 5.3 m2/l [212.5 sq.ft./US gallon] - 80 micron/3.2 mils
Flash point: 32 °C [89.6 °F]
Specific gravity: 1.3 kg/litre [10.9 lbs/US gallon]
Surface-dry: 1 hour(s) 20°C/68°F
Through-dry: 4 hour(s) 20°C/68°F
VOC content: 510 g/l [4.2 lbs/US gallon]
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Application method: Airless spray / Air spray / Brush (touch up)
Nozzle orifice: 0.021 - 0.023 "
Nozzle pressure: 150 bar [2175 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: THINNER 08080
Indicated film thickness, dry: 80 micron [3.2 mils] see REMARKS overleaf
Indicated film thickness, wet: 175 micron [7 mils]
Overcoat interval, min: see REMARKS overleaf
Overcoat interval, max: see REMARKS overleaf
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
SURFACE PREPARATION: New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other
contaminants by high pressure fresh water cleaning. Abrasive blasting to Sa 2½ (ISO 8501-1:2007).
For temporary protection, if required, use a suitable shopprimer. All damage of shopprimer and
contamination from storage and fabrication should be thoroughly cleaned prior to final painting.
Repair and maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove
salts and other contaminants by high pressure fresh water cleaning. Remove all rust and loose material
by abrasive blasting or power tool cleaning. Dust off residues. Touch up bare spots to full film thickness.
APPLICATION CONDITIONS: Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.
In confined spaces provide adequate ventilation during application and drying.
PRECEDING COAT: None, or as per specification.
SUBSEQUENT COAT: None, or as per specification. Recommended systems are: HEMPATEX.
Ship bottoms: Antifouling according to specification.
REMARKS:
Weathering/service temperatures: As the paint is a thermoplastic product, prolonged mechanical exposure at temperatures above
approximately 40°C/105°F may cause film indentation. When temperature drops below, mechanical
strength is recovered.
Film thicknesses/thinning: May be specified in another film thickness than indicated depending on purpose and area of use. This
will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:
60-100 micron/2.4-4 mils. A series of maintenance jobs may result in build up of a too high total film
thickness which may cause blister formation due to "entrapped" solvents. As each coat may also retain
solvents, it is generally recommended not to apply the product in excessive film thickness.
Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high
pressure fresh water hosing and allow drying.
Overcoating intervals: In case of multi-coat application, drying time and minimum overcoating interval will be influenced by the
number of coats and by thickness of each coat applied - reference is made to the corresponding
painting specification.
No maximum overcoating interval, but after prolonged exposure to polluted atmosphere remove
accumulated contamination by (high pressure) fresh water cleaning and allow to dry.
Note: HEMPATEX HI-BUILD 46330 For professional use only.
ISSUED BY: HEMPEL A/S 4633011480
Description: HEMPEL'S SILVIUM 51570 is an oleoresinous general purpose aluminium paint with good heat
resistance and good light reflection.
Recommended use: For protection of hot pipelines, exhaust pipes, smoke stacks and other hot surfaces upto peak
temperatures of 250°C/482°F and upto permanent temperatures of 200°C/392°F.
As a finishing coat on steel and woodwork exterior and interior in mild to moderately corrosive
environment where an aluminium surface or light reflection is desired.
Service temperature: Maximum, dry exposure only: 200°C/392°F, (peak) 250°C/482°F
Certificates/Approvals: Tested according to section 175.300 of the Code of Federal Regulations Title 21 - Dry Foodstuff.
Consult Hempel for details.
Tested for non-contamination of grain cargo at the Newcastle Occupational Health & Hygiene, Great
Britain.
Complies with EU Directive 2004/42/EC: subcategory i.
Availability: Part of Group Assortment. Local availability subject to confirmation.
PHYSICAL CONSTANTS:
Shade nos/Colours: 19000 / Aluminium
Finish: Glossy see REMARKS overleaf
Volume solids, %: 38 ± 1
Theoretical spreading rate: 15.2 m2/l [609.5 sq.ft./US gallon] - 25 micron/1 mils
Flash point: 38 °C [100.4 °F]
Specific gravity: 0.9 kg/litre [7.8 lbs/US gallon]
Surface-dry: 1 hour 20°C/68°F
Through-dry: 3.5 hour(s) 20°C/68°F
VOC content: 505 g/l [4.2 lbs/US gallon]
Shelf life: 5 years (25°C/77°F) from time of production.
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Application method: Airless spray / Air spray / Brush
Thinner (max.vol.): Do not dilute. see REMARKS overleaf
Nozzle orifice: 0.017 "
Nozzle pressure: 100 bar [1450 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S THINNER 08080
Indicated film thickness, dry: 25 micron [1 mils]
Indicated film thickness, wet: 75 micron [3 mils]
Overcoat interval, min: According to specification.
Overcoat interval, max: According to specification.
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
SURFACE PREPARATION: New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other
contaminants by high pressure fresh water cleaning. Power tool cleaning to St 3 or abrasive blasting to
Sa 2 (ISO 8501-1:2007). Prime with: HEMPALIN
Repair and maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove
salts and other contaminants by high pressure fresh water cleaning. Remove all rust and loose material
by abrasive blasting or power tool cleaning. Dust off residues. Prime with: HEMPALIN. Touch up bare
spots with: HEMPEL'S SILVIUM 51570.
APPLICATION CONDITIONS: Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.
In confined spaces provide adequate ventilation during application and drying.
PRECEDING COAT: Steel surface temperature: below 120°C/248°F HEMPALIN PRIMER. 120-200°C/248-390°F self primed.
SUBSEQUENT COAT: None.
REMARKS:
Colours/Colour stability: Has a tendency to yellow after application. This has no influence on the performance nor does the
yellowing affect any topcoat applied.
Application(s): Spray application is recommended.
If applied by brush, use a flat brush not more than 10 cm/4" wide. Do not dilute. After the paint has
been distributed it should be laid off with light strokes and in one direction only. If the paint is worked
too much with brush or roller, it will become streaky and greyish and lose its lustre. This effect is
cosmetic only and has no influence on the protective properties.
Finish: At high temperatures the paint will become greyish and lose its lustre. This effect is cosmetic
only and has no influence on the protective properties.
Note: HEMPEL'S SILVIUM 51570 For professional use only.
ISSUED BY: HEMPEL A/S 5157019000
52140
Description: HEMPALIN ENAMEL 52140 is a glossy alkyd enamel which forms a weather resistant coating. It is
flexible and resistant to salt water and spillage of mineral oil and other aliphatic hydrocarbons.
Recommended use: As a general purpose finishing coat in alkyd systems on exterior and interior steel and woodwork in
mildly to moderately corrosive environment. As a finishing coat in engine rooms including tank tops,
main engines and auxiliary machinery.
Service temperature: Maximum, dry exposure only: 120°C/248°F (These temperatures may cause yellowing/discolouration.)
Certificates/Approvals: Approved as a low flame spread material when used as part of a predefined paint system. Please refer
to “Declaration of Conformity” on www.Hempel.com for further details.
Complies with EU Directive 2004/42/EC: subcategory i.
Availability: Part of Group Assortment. Local availability subject to confirmation.
PHYSICAL CONSTANTS:
Shade nos/Colours: 10000* / White.
Finish: Glossy
Volume solids, %: 46 ± 1
Theoretical spreading rate: 15.3 m2/l [613.5 sq.ft./US gallon] - 30 micron/1.2 mils
Flash point: 38 °C [100.4 °F]
Specific gravity: 1.1 kg/litre [9 lbs/US gallon]
Surface-dry: 3 hour(s) 20°C/68°F
Through-dry: 5.5 hour(s) 20°C/68°F
VOC content: 429 g/l [3.6 lbs/US gallon]
Shelf life: 5 years (25°C/77°F) from time of production.
- *Wide range of colours available via Hempel's MULTI-TINT system.
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Application method: Airless spray / Air spray / Brush
Thinner (max.vol.): 08230 (5%) / 08230 (15%) / 08230 (5%) see REMARKS overleaf
Nozzle orifice: 0.018 "
Nozzle pressure: 150 bar [2175 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S THINNER 08230
Indicated film thickness, dry: 30 micron [1.2 mils]
Indicated film thickness, wet: 75 micron [3 mils]
Overcoat interval, min: see REMARKS overleaf
Overcoat interval, max: see REMARKS overleaf
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
SURFACE PREPARATION: New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other
contaminants by high pressure fresh water cleaning. Power tool cleaning to St 3 or abrasive blasting to
Sa 2 (ISO 8501-1:2007). Prime with: HEMPALIN
Repair and maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove
salts and other contaminants by high pressure fresh water cleaning. Remove all rust and loose material
by abrasive blasting or power tool cleaning. Dust off residues. Prime with: HEMPALIN. Touch up bare
spots with: HEMPALIN ENAMEL 52140.
APPLICATION CONDITIONS: Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.
In confined spaces provide adequate ventilation during application and drying.
PRECEDING COAT: According to specification. Recommended systems are: HEMPALIN PRIMER 12050 or HEMPALIN
PRIMER HI-BUILD 13200 or HEMPALIN UNDERCOAT 42460
SUBSEQUENT COAT: None.
REMARKS:
VOC - EU Directive 2004/42/EC:
Not available.
Product As supplied 15 vol. % thinning Limit phase II, 2010
5214010000 429 g/l 493 g/l 500 g/l
For VOC of other shades, please refer to Safety Data Sheet.
Colours/Colour stability: Colour stability for some shades may be effected by exposure to harsh chemical atmospheres. This
does not affect the performance of the coating.
For certain colours extra coats may be necessary to obtain full opacity. This does not affect the
performance of the coating.
Film thicknesses/thinning: THINNER 08080 may be used for a spray application, however, with a certain risk of wrinkling of a
preceding fresh HEMPALIN coat.
May be specified in another film thickness than indicated depending on purpose and area of use. This
will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:
30-40 micron/1.2-1.6 mils
Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high
pressure fresh water hosing and allow drying.
Overcoating intervals: Overcoating intervals related to later conditions of exposure: Recommended dry film thickness: 30
micron/1.2 mils of HEMPALIN ENAMEL52140.
If the maximum overcoating interval is exceeded, roughening of the surface is necessary to ensure
intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high
pressure fresh water hosing and allow drying.
APPLICATION DETAILS:
Version, mixed product: 55210
Mixing ratio: BASE 55219: CURING AGENT 95370
7:1 by volume
Application method: Airless spray / Brush
Thinner (max.vol.): see REMARKS overleaf / 08080 (5%)
Pot life: 4 hour(s) 20°C/68°F
Nozzle orifice: 0.017 - 0.019 "
Nozzle pressure: 150 bar [2175 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S THINNER 08080 or 08510
Indicated film thickness, dry: 50 micron [2 mils] see REMARKS overleaf
Indicated film thickness, wet: 100 micron [4 mils]
Overcoat interval, min: see REMARKS overleaf
Overcoat interval, max: see REMARKS overleaf
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
-
-
-
-
-
-
-
-
-
-
-
For aluminium pigmented shades scratching actions or high humidity/water may cause discolouration/
disturbances of the surface. This will have no influence on the performance. This phenomenon may be
avoided by applying a clear varnish.
Weathering/service temperatures: At service temperature above 100°C/212°F, slight discolouration may be expected.
Film thicknesses/thinning: The type and amount of thinner depend on application conditions, application method, temperature,
ventilation, and substrate. THINNER 08080 is recommended in general.
Airless spray: 5-10% thinning is recommended. Under extreme conditions up to more than 20% may
be necessary to obtain satisfactory film formation.
Electrostatic spray: 10% thinning is recommended. Contact HEMPEL for more information.
May be specified in another film thickness than indicated depending on purpose and area of use. This
will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:
40-75 micron/1.6-3 mils.
Shades: This product is available in several aluminium pigmented shades with different volume solids content.
Contact HEMPEL for more information.
Curing agent: CURING AGENT 95370: is sensitive to moisture.
Even small traces of water in the mixed paint will reduce the pot life and result in film defects.
Open curing agent cans with caution as overpressure might exist. Store in a dry place and keep the
can tightly closed until use.
Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high
pressure fresh water hosing and allow drying.
Description: HEMPEL’S SILICONE ALUMINIUM 56910 is a heat resistant aluminium pigmented polysiloxane paint.
Recommended use: For long-term protection of hot pipelines, exhaust pipes, smoke stacks and other hot surfaces. In
corrosive environment see PRECEDING COAT overleaf.
Service temperature: Maximum, dry exposure only: 600°C/1112°F
Certificates/Approvals:
Availability: Part of Group Assortment. Local availability subject to confirmation.
PHYSICAL CONSTANTS:
Shade nos/Colours: 19000/ Aluminium
Finish: Semi-flat see REMARKS overleaf
Volume solids, %: 35 ± 1
Theoretical spreading rate: 14 m2/l [561.4 sq.ft./US gallon] - 25 micron/1 mils
Flash point: 25 °C [77 °F]
Specific gravity: 1.1 kg/litre [9.3 lbs/US gallon]
Surface-dry: 1 approx. hour(s) 20°C/68°F
Dry to touch: 2 - 4 hour(s) 20°C/68°F
VOC content: 562 g/l [4.7 lbs/US gallon]
Shelf life: 1 year (25°C/77°F) from time of production.
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Application method: Airless spray / Air spray / Brush
Thinner (max.vol.): 08080 (5%) / 08080 (15%) / 08080 (5%) (see REMARKS overleaf)
Nozzle orifice: 0.017 "
Nozzle pressure: 125 bar [1812.5 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S THINNER 08080
Indicated film thickness, dry: 25 micron [1 mils] see REMARKS overleaf
Indicated film thickness, wet: 75 micron [3 mils]
Overcoat interval, min: 6 hour(s) 20°C/68°F (According to specification.)
Overcoat interval, max: None.
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
SURFACE PREPARATION: Maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other
contaminants by high pressure fresh water cleaning.
Abrasive blasting to Sa 2½ (ISO 8501-1:2007).
APPLICATION CONDITIONS: Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.
In confined spaces provide adequate ventilation during application and drying.
PRECEDING COAT: According to specification. Recommended systems are: HEMPEL'S SILICONE ZINC 16900,
HEMPEL’S GALVOSIL 15700
SUBSEQUENT COAT: None.
REMARKS:
Description: VERSILINE CUI 56990 is a MIO pigmented single component inorganic copolymer coating
which cures to form an inert polymer matrix able to resist temperatures up to 650°C/1202°F
and thermal shock/cycling in dry or dry/wet service.
Recommended use: For long-term protection of hot pipework, equipment and other hot surfaces. Applied directly
onto the steel substrate. Specially developed to prevent corrosion under insulation (CUI).
Physical constants:
Application details:
Safety: Handle with care. Before and during use, observe all safety labels on packaging and
paint containers, consult Hempel Material Safety Data Sheets and follow all local
or national safety regulations.
Surface preparation: New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and
other contaminants by high pressure fresh water cleaning. Abrasive blasting to near white
metal Sa 2½ (ISO 8501-1:2007) with a surface profile corresponding to Rugotest No. 3,
BN10a, Keane-Tator Comparator 3.0 G/S, or ISO Comparator Rough Medium (G). After
blasting, clean the surface carefully from abrasives and dust.
Repair and maintenance: Remove oil and grease, etc. with suitable detergent. Remove salt
and other contaminants by (high pressure) fresh water cleaning. Clean damaged areas
thoroughly by power tool cleaning to min. St 2, preferably St 3 (minor areas) or by abrasive
blasting to min. Sa 2, preferably to Sa 2½. Improved surface preparation will improve the
performance of the paint. Recommended surface profile is Rz 75-100 micron/3-4 mils,
corresponding to Rugotest No. 3, BN10a, Keane-Tator Comparator, minimum 3.0 G/S, or ISO
Comparator, Medium (G). After blasting clean the surface carefully from abrasives and dust.
Application conditions: Apply only on a dry and clean surface with a temperature min. 3°C/5°F above the dew point to
avoid condensation. Use only where application and curing can proceed at temperatures
above: 10°C/50°F. Minimum steel temperature: 10°C/50°F. May be applied on to hot
substrates up to maximum 200°C/ 392°F. The relative humidity should preferably be 40-60%,
maximum 80%.
Subsequent coat: HEMPEL’S SILICONE TOPCOAT 56900, HEMPEL’S SILICONE ACRYLIC 56940, HEMPEL’S
SILICONE ALUMINIUM 56910 or according to specification.
Remarks: The product cures to a hard film and provides good anticorrosive protection at ambient
temperature. Anticorrosive properties are enhanced following high temperature exposure in
service. Best anticorrosive properties are achieved by heating the coating gradually on first
time exposure.
Colours/colour stability: The coating will discolour at high service temperatures. This will not influence the anticorrosive
properties of the paint.
Volume solids,%: This product is available in an aluminium pigmented shade with different volume solids
content.
Stirring: Mechanical stirring is necessary before usage. See separate Application instructions.
Description: HEMPADUR 85210 is a two component epoxy/amine adduct tank lining in accordance with MIL-
C-4556-F and MIL-PRF-4556-F specification.
Recommended use: As a tank coating system for fuel and similar cargoes.
Availability: Not included in Group Assortment. Availability subject to special agreement.
PHYSICAL CONSTANTS:
Shade nos/Colours: 11630* / Off-white.
Finish: Semi-flat
Volume solids, %: 62 ± 1
Theoretical spreading rate: 6.2 m2/l [248.6 sq.ft./US gallon] - 100 micron/4 mils
Flash point: 37 °C [98.6 °F]
Specific gravity: 1.4 kg/litre [11.7 lbs/US gallon]
Dry to touch: 5 hour(s) 20°C/68°F
Fully cured: 7 day(s) (approx.) 20°C/68°F
VOC content: 339 g/l [2.8 lbs/US gallon]
Shelf life: 1 year 20°C/68°F
- *other shades according to assortment list.
(MIL-PRF-4556-F requires yellow (21240) as the first coat)
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Version, mixed product: 85210
Mixing ratio: BASE 85219: CURING AGENT 89110
4:1 by volume
Application method: Airless spray / Brush (touch up)
Thinner (max.vol.): 08450 (5%)/ 08450 (5%)
Pot life (Airless spray): 2 hour(s) 20°C/68°F
Pot life (Brush): 4 hour(s) 20°C/68°F
Nozzle orifice: 0.021 "
Nozzle pressure: 150 bar [2175 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S TOOL CLEANER 99610
Indicated film thickness, dry: 100 micron [4 mils]
Indicated film thickness, wet: 150 micron [6 mils]
Overcoat interval, min: According to specification.
Overcoat interval, max: According to specification.
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
Overcoating intervals: If the maximum overcoating interval is exceeded, roughening of the surface is necessary to ensure
intercoat adhesion.
Do not put tanks into service until the paint system is completely cured.
Nota: HEMPADUR 85210 For professional use only.
ISSUED BY: HEMPEL A/S 8521011630
The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Version, mixed product: 85550
Mixing ratio: BASE 85559 : CURING AGENT 95690
5.6 : 1.0 by volume
Application method: Spray (small areas: notched trowel)
(Consult separate Application Instructions)
Thinner (max.vol.): Do not dilute (See REMARKS overleaf)
Pot life: 1 hour (20°C/68°F)
Recommended GRACO ToughTek M680a spray equipment
equipment: (Consult separate Application Instructions)
For small area: Quick Spray Hopper Gun
Cleaning of tools: HEMPEL'S TOOL CLEANER 99610
Indicated film thickness, dry: 2.5mm [100 mils]
Indicated film thickness, wet: 2.5mm [100 mils]
Overcoat interval, min: See REMARKS overleaf
Overcoat interval, max: See REMARKS overleaf
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
SURFACE PREPARATION: New steel: Abrasive blasting to Sa 21/2 or Sa 3 (ISO 8501-1:2007), depending on area of use. Surface
profile corresponding to Rugotest No. 3, BN11, Keane-Tator Comparator 5.5 G/S, or ISO Comparator
Coarse (G). Oil and grease must be removed with suitable detergent, salt and other contaminants by
(high pressure) fresh water cleaning prior to blasting. After blasting, clean the surface carefully from
abrasives and dust. The blasted and cleaned surface may advantageously be primed with HEMPADUR
15590.
Concrete: Remove slip agent and other possible contaminants by emulsion washing followed by high
pressure hosing with fresh water. Remove scum layer and loose matter to a hard, rough and uniform
surface, preferably by abrasive blasting, possibly by other mechanical treatment flame cleaning or acid
etching. Seal surface with suitable sealer, e.g. HEMPADUR SEALER 05990 as per relevant painting
specification (furthermore, see Product Data Sheet for 05990.
APPLICATION CONDITIONS: Use only where curing can proceed at temperature above 10°C/50°F. Minimum application
temperature of the substrate is 20°C/68°F.
To facilitate stirring and mixing, the temperature of the paint should in no case be less than
approximately 20°C/68°F
Apply only on a dry and clean surface with a temperature above the dew point to avoid
condensation.
PRECEDING COAT: None, HEMPADUR SEALER 05990, HEMPADUR 15590, or according to specification.
SUBSEQUENT COAT: None, or HEMPADUR qualities according to specification. In case a “smoothening” of the surface is
required, HEMPADUR MULTI-STRENGTH 45751 may be used.
REMARKS:
Weathering/Temperatures: The natural tendency of epoxy coatings to chalk in outdoor exposure and become more sensitive to
mechanical damage and chemical exposure at elevated temperature is also reflected in this product.
Film thicknesses/thinning: Film thicknesses:
May be specified in another film thickness than indicated depending on purpose and area of use. Not
recommended below 2.5mm/100 mils, since HEMPADUR SPRAY-GUARD 85550 will not form a
closed and pinhole-free film at lower film thickness.
Thinning:
Do not dilute as this will influence adhesion and cohesion of the paint system.
Adhesion: Proper adhesion is obtained by applying HEMPADUR SPRAY-GUARD 85550 directly to the steel. If a
blast primer is required, HEMPADUR 15590 is recommended.
Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high
pressure fresh water hosing and allow drying.
A specification supersedes any guideline overcoat intervals indicated in the table.
Environment Atmospheric, severe
Surface temperature: 10°C (50°F) 20°C (68°F) 30°C (86°F)
Min Max Min Max Min Max
HEMPADUR Not relevant 2 months 8h 1 month 4h 2 weeks
Overcoating note: The surface MUST be completely clean before overcoating. All dust, abrasives and loose dry spray
must be removed by vacuum cleaning. Dry spray should be removed by light abrading.
Note: HEMPADUR SPRAY-GUARD 85550 For professional use only.
ISSUED BY: HEMPEL PAINTS (SAUDI ARABIA) W.L.L. – 8555041690CR002
APPLICATION DETAILS:
Version, mixed product: 85671
Mixing ratio: BASE 85675 : CURING AGENT 97371
8.8 : 1.2 by volume
13.8 : 1.0 by weight
Application method: Airless spray / Brush (touch up)
Thinner (max.vol.): HEMPEL'S THINNER 08450 (According to separate APPLICATION INSTRUCTIONS)
Pot life: 3 hour(s) 20°C/68°F
Induction time: 15 minute(s) 20°C/68°F (According to separate APPLICATION INSTRUCTIONS)
Nozzle orifice: 0.018 - 0.021 "
Nozzle pressure: 200 bar [2900 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S TOOL CLEANER 99610
Indicated film thickness, dry: 100 micron [4 mils] see REMARKS overleaf
Indicated film thickness, wet: 150 micron [6 mils]
Overcoat interval, min: According to separate APPLICATION INSTRUCTIONS
Overcoat interval, max: According to separate APPLICATION INSTRUCTIONS
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
-
-
-
-
-
-
-
-
-
SURFACE PREPARATION: New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other
contaminants by high pressure fresh water cleaning. Abrasive blasting to near white metal Sa 2½ (ISO
8501-1:2007) with a surface profile corresponding to Rugotest No. 3, BN10a, Keane-Tator Comparator
3.0 G/S, or ISO Comparator Medium (G).
Repair and maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove
salts and other contaminants by high pressure fresh water cleaning. Other degrees of cleaning
including wet methods like ultra-high-pressure-water-jetting (UHPWJ) and blasting with mixtures of grit
and water may be relevant according to Hempel-specification. Remove water, any residual blasting
material and other debris. Old steel surfaces having been exposed to salt water, excessive amounts of
salt residues in pittings may call for abrasive blasting, high pressure fresh water hosing, drying, and
finally, dry abrasive blasting again.
Concrete: Remove slip agent and other possible contaminants by emulsion washing followed by high
pressure hosing with fresh water. Remove scum layer and loose matter to a hard, rough and uniform
surface, preferably by abrasive blasting, possibly by other mechanical treatment or acid etching. Seal
surface with suitable sealer, as per relevant painting specification.
APPLICATION CONDITIONS: Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.
Use only where application and curing can proceed at temperatures above: 10°C/50°F. The
temperature of paint itself should be 15°C/59°F or above. Curing requires a relative humidity of: max
80%.
In confined spaces provide adequate ventilation during application and drying.
Reference is made to separate APPLICATION INSTRUCTIONS.
PRECEDING COAT: None, or as per specification.
SUBSEQUENT COAT: None, or as per specification.
REMARKS:
Thinning:
Keep thinning at absolute minimum. Do not dilute the components separately - only the mixture.
Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high
pressure fresh water hosing and allow drying.
Overcoating note: The surface MUST be completely clean before overcoating. All dust, abrasives and loose dry spray
must be removed by vacuum cleaning. Dry spray should be removed by light abrading.The coating
may only be exposed to strong direct sunlight or ultraviolet light under exceptional circumstances and
then only for short periods.
The coating is to be checked carefully and any patchy, whitish, and/or greasy formation, must be
completely removed by suitable cleaning method.
Note: HEMPADUR 85671 For professional use only.
ISSUED BY: HEMPEL A/S 8567111150
X Move PDS Disclaimer to Second page
This Product Data Sheet supersedes those previously issued.
For explanations, definitions and scope, see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations given in this data sheet
represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions
of any intended use of the Products herein must be determined exclusively by the Buyer and/or User.
The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed
in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said
GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise.
Product data are subject to change without notice and become void five years from the date of issue.