Documente Academic
Documente Profesional
Documente Cultură
GDC-004/09
Product Catalog
Edition 2.0
Confidential
The information contained in this document is subject to change without prior notice.
All copyright, intellectual and industrial rights in this document and in the technical knowledge it contains
are owned by INTRACOM S.A. TELECOM SOLUTIONS and/or their respective owners.
This document is made available to the end users only for their internal use.
No part of this document nor any data herein may be published, disclosed, copied, reproduced,
redistributed by any form or means, electronically or mechanically, or used for any other purpose
whatsoever without the prior written approval of INTRACOM S.A. TELECOM SOLUTIONS.
Information as well as drawings and specifications contained in this document are subject to change
without prior notice.
All trademarks and copyrights mentioned herein are the property of INTRACOM S.A. TELECOM
SOLUTIONS and/or their respective owners.
Any rights not expressly granted herein are reserved.
Printed in Greece.
INTRACOM TELECOM
19.7 km Markopoulou Ave., Peania, Athens, GR 19002
T +30 210 667 1000, F +30 210 667 1001
http://www.intracom-telecom.com
email (product support): wireless-support@intracom-telecom.com
Document Revision History OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
Reasons of The table below shows the reasons for the document change effected in
change relation to the previous document edition.
-I-
OmniBAS Outdoor Units (ODUs) Document Revision History
Product Catalog - Edition 2.0
-II-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
Table of Contents
1. Introduction .................................................................................................................. 1
About this Document .......................................................................................................... 1
3. Antennas ....................................................................................................................... 6
6 GHz Band........................................................................................................................ 8
7 / 8 GHz Band ................................................................................................................. 10
11 GHz Band .................................................................................................................... 12
13 GHz Band .................................................................................................................... 14
15 GHz Band .................................................................................................................... 16
18 GHz Band .................................................................................................................... 18
23 GHz Band .................................................................................................................... 20
26 GHz Band .................................................................................................................... 22
28 GHz Band .................................................................................................................... 24
38 GHz Band .................................................................................................................... 26
4. Coupler ....................................................................................................................... 28
6. Grounding ................................................................................................................... 40
Grounding Kit ................................................................................................................... 40
7. Others ......................................................................................................................... 41
Consumables ................................................................................................................... 42
IF Cable Adaptation Connector ........................................................................................ 43
Antenna Adaptation Plate ................................................................................................. 44
RSSI Cables ..................................................................................................................... 45
Trimming Tool for IF Cable ............................................................................................... 46
-III-
Table of Contents
-IV-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
Equipment Disposal
-V-
Table of Contents
Declaration of Conformity
Δήλωση Συμμόρφωσης
-VI-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
1. Introduction
About this Document
Scope of The scope of this document is to provide all the available order codes for the
document following equipment and materials:
• OmniBASTM ODUs
• Antennas
• Couplers
• ODU/Coupler Mounting Kits
• Cables, Connectors & Accessories
-1-
2. Radio Equipment
2. Radio Equipment
ODU-CF 6, 11 and 26
ODU-CFs 18 and 38
-2-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
For package box dimensions and gross weight please instruct the Appendix A:
Package Dimensions & Weights on page 57.
(1)
ODU-CFe at antenna port has built-in customized polarizer therefore cannot be used directly to FLEX-
TWIST waveguide cable. For non-integrated installations the proper ODU / coupler mounting kit must be used
by using FLEX-TWIST waveguide cable (see reference Mounting Kit for all ODUs & Coupler on page 50)
-3-
2. Radio Equipment
ODU-CF & ODU-CFe coding Find below the ODU-CF & ODU-CFe (1) coding:
(1)
For details please refer to Operating Frequencies for Point-to-Point (PtP) Radio Systems manual.
For ODU availability please contact Intracom Telecom S.A.
-4-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
(1)
For details please refer to Operating Frequencies for Point-to-Point (PtP) Radio Systems manual.
For ODU availability please contact Intracom Telecom S.A.
-5-
3. Antennas
3. Antennas
Overview This chapter describes the available integrated antenna types per frequency
band.
For package box dimensions and gross weight please instruct the
Appendix A: Package Dimensions & Weights on page 57.
-6-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
Antennas, Continued
OMT overview Orthomode Transducers (OMTs) are 3-port microwave waveguide systems
that split the input power into two parts (based on polarization separation),
consequently, allow the simultaneous operation of two outdoor radio units
(ODUs). Since the devices provide high inter-port isolation and low return
loss, their application together with high performance antennas lead to use
of two independent transmission channels on a single antenna at the same
time.
vertical (V)
V+H OMT
horizontal (H)
OMT can be directly mounted on antennas (as shown below) that have
circular waveguide connector. Interfaces are available for several types of
antennas from several manufacturers.
OMT included into packaging of the dual polarization antenna for XPIC
operation.
-7-
3. Antennas
6 GHz Band
-8-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
-9-
3. Antennas
7 / 8 GHz Band
-10-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
-11-
3. Antennas
11 GHz Band
-12-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
-13-
3. Antennas
13 GHz Band
-14-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
-15-
3. Antennas
15 GHz Band
-16-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
-17-
3. Antennas
18 GHz Band
-18-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
-19-
3. Antennas
23 GHz Band
-20-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
-21-
3. Antennas
26 GHz Band
-22-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
-23-
3. Antennas
28 GHz Band
-24-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
-25-
3. Antennas
38 GHz Band
-26-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
-27-
4. Coupler
4. Coupler
Overview The coupler (with two ODUs mounted on it) is used when hot standby
(asymmetrical coupler) or 2+0 (symmetrical coupler) operation modes is
needed using only one antenna (see below figure). The coupler / hybrid is a
3-port microwave system that splits the input RF power into two parts
(picture 3 below). For typical coupling coefficients (dB) please refer to
Coupler order codes on page 31.
Intracom Telecom provides specially designed antennas (called integrated
antennas with diameter up to 1.8 m or 6 ft) onto which it can directly be
mounted the coupler without the need of a waveguide. In case of a non-
integrated antenna, the appropriate mounting kit should be in order to mount
the coupler onto the mast and connect the coupler to the antenna through a
waveguide.
Coupler Diagram
-28-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
Coupler, Continued
No. Description
1 Coupler brackets.
2 Coupler.
3 Grounding lugs.
4 Greasing paste.
5 Bolts and nuts for assembly of mounting bracket.
6 Grounding cables.
-29-
4. Coupler
Coupler, Continued
Coupler The coupler / hybrid provide high inter-port isolation and low return loss.
application Combined with a single-polarized, high-performance antenna, the coupler /
hybrid allows the concurrent transmission of two independent channels over
the link.
Configuration Description
Two ODUs are used in a hot standby 1+1
configuration for increasing link availability
1+1 link
and reliability (see Coupler installation
diagram on page 28)
Two ODUs are used, operating in two
different frequency channels, for doubling
2+0 link
the transmission capacity (see Coupler
installation diagram on page 28)
-30-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
Coupler, Continued
P1 / P2 Band
Code Description Symmetrical Asymmetrical
(dB) (GHz)
-31-
5. IF Cables & Accessories
-32-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
IF Cables
IF cables The IF cables are used for the connection between IF tail (CAB IFTAIL) and
ODU.
-33-
5. IF Cables & Accessories
IF Connectors
Selection The IF connectors are used for the termination of the IF cable (ACC-CI-VV-
criteria VV-D4 & ACC-CI-VV-VV-D2).
Order codes
Order Code / Photo Description Details
ACC-FC-ST-VV-D4 CONN, N(M), FOR 1/4"(LCF) COAX, • N-type straight male
O-RING connector for terminating ¼’’
IF cable
• O-ring
ACC-FC-RA-VV-D4 CONN, N(m), R/A, w/O-RING, FOR • N-type right angle (R/A)
CF14-50 connector for terminating ¼’’
IF cable
• O-ring
ACC-FC-ST-VV-D2 CONN, N(M), FOR 1/2" (LCF) COAX • N-type male connector for
CABLE terminating ½” IF cable
• Sealing cover
ACC-FC-RA-VV-D2 CONN, N(M), R/A, FOR 1/2"(LCF), • N-type right angle (R/A)
PLAST 2000 male connector for
terminating ½” IF cable
• Sealing cover
-34-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
IF Connectors, Continued
ODU side:
ODU-CFs Single ODU-CFs onto antenna According to the specific position of the ODU-CFs onto
the pole.
ODU-CF Single ODU-CF onto antenna According to the specific orientation of the ODU-CF. (1)
(1) Alternatively, one R/A IF connector could be used for all cases.
-35-
5. IF Cables & Accessories
IF Cable Clamps
IF cable clamps The clamp provide the best solution for fastening the IF cables onto tower.
-36-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
IF cable tie The clamp provide the best solution for fastening the IF cables onto tower.
wraps
It is recommended to use one clamp for every 1 m distances.
-37-
5. IF Cables & Accessories
IF cable There are two types of grounding kits for the IF cables depending on the
grounding kit type of the IF cable.
The number of grounding kits used depends on the distance between the
IDU and the ODU as shown below:
-38-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
IF Tail
IF tail The IF tail is used for the connection between the indoor unit (IF modem
receptacle) and the IF cable (ACC-CI-VV-VV-D4 or ACC-CI-VV-VV-D2) using
also the appropriate N-type straight connector (ACC-FC-ST-VV-D4 or ACC-FC-
ST-VV-D2).
-39-
6. Grounding
6. Grounding
Grounding Kit
-40-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
7. Others
-41-
7. Others
Consumables
Consumables The following materials used for installation of ODU onto antenna and IF
cable termination using IF connectors.
Greasing paste for Antennas O-Ring. Used for antenna O-ring when
GRS-PST the radio unit is installed onto
the antenna.
-42-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
IF cable The following material is used for specific IF cable only (NEC):
adaptation
connector
-43-
7. Others
Antenna The following material is used for specific antennas only (NEC):
adaptation
plate
-44-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
RSSI Cables
RSSI cable The following materials used for antenna alignment only:
-45-
7. Others
Trimming tool The following material is used for the 1/4″ IF cable preparation prior to
for IF cable connector attachment:
-46-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
8. Mounting Kit
-47-
8. Mounting Kit
Mounting kit for The following kit can be used when non-integrated antennas need to be
one ODU-CF connected to one ODU-CF.
KIT INSTALLED
-48-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
Mounting kit for The following kit can be used when non-integrated antennas need to be
two ODUs-CF connected to two ODUs-CF.
KIT INSTALLED
-49-
8. Mounting Kit
-50-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
9. Waveguide Kits
-51-
9. Waveguide Kits
Table selection Select the Flexible / Twistable Waveguide Kit from the table below using as selecting
criteria the frequency band, the waveguide length and the flange type:
Order Code Description Supported Supported
ODU ANTENNAS
flanges flanges
ACC-FW-06 (1)-D7-09 FLEX-TWIST W/G Kit 6 GHz, 900 mm,
UDR70/PDR70
ACC-FW-06-D7-12 FLEX-TWIST W/G Kit 6GHz, 1200 mm,
UDR70 PDR70
UDR70/PDR70
ACC-FW-06-D7-15 FLEX-TWIST W/G Kit 6GHz, 1500 mm,
UDR70/PDR70
ACC-FW-07-D1-09 FLEX-TWIST W/G Kit 7/8 GHz, 900 mm,
UDR84/PBR84
ACC-FW-07-D1-12 FLEX-TWIST W/G Kit 7/8 GHz, 1200 mm,
UBR84 PDR84
UDR84/PBR84
ACC-FW-07-D1-15 FLEX-TWIST W/G Kit 7/8 GHz, 1500 mm,
UDR84/PBR84
ACC-FW-11-B6-06 FLEX-TWIST W/G Kit 11 GHz, 600 mm,
PBR100/UBR100
ACC-FW-11-B6-12 FLEX-TWIST W/G Kit 11 GHz, 1200 mm,
UBR100 PBR100
PBR100/UBR100
ACC-FW-11-B6-15 FLEX-TWIST W/G Kit 11 GHz, 1500 mm,
PBR100/UBR100
ACC-FW-13-B2-12 FLEX-TWIST W/G Kit 13 GHz, 1200 mm,
UBR120/PBR120
UBR120 PBR120
ACC-FW-13-B2-15 FLEX-TWIST W/G Kit 13 GHz, 1500 mm,
UBR120/PBR120
ACC-FW-15-B3-12 FLEX-TWIST W/G Kit 15 GHz, 1200 mm,
UBR140/PBR140
UBR140 PBR140
ACC-FW-15-B3-15 FLEX-TWIST W/G Kit 15 GHz, 1500 mm,
UBR140/PBR140
ACC-FW-23-B4-12 FLEX-TWIST W/G Kit 18-26 GHz, 1200 mm,
UBR220/PBR220
UBR220 PBR220
ACC-FW-23-B4-15 FLEX-TWIST W/G Kit 18-26 GHz, 1500 mm,
UBR220/PBR220
ACC-FW-38-B5-03 FLEX-TWIST W/G Kit 28-38 GHz, 300 mm,
PBR320/UBR320
ACC-FW-38-B5-06 FLEX-TWIST W/G Kit 28-38 GHz, 600mm,
UBR320 PBR320
PBR320/UBR320
ACC-FW-38-B5-09 FLEX-TWIST W/G Kit 28-38 GHz, 900mm,
PBR320/UBR320
(1)
For ODU-CF 6 GHz you need to use an adaptor with order code ACC-FW-06-VV-VV and description 6
GHz W/G ADAPTOR KIT, UDR70.
-52-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
-53-
9. Waveguide Kits
Waveguide Select the Waveguide Clamp Kit (standard or extended) from the table below
clamp kit using as selecting criteria the frequency band and configuration. The kit is
used for the waveguide clamping on the pole (recommended in areas with
strong wind).
The table also shows the number of kits the manufacturer suggests for better
waveguide clamping.
ACC-FL-06-LU-EX Extended W/G clamp kit 6 GHz, 1+0 1 for 1+0 configuration.
ACC-FL-06-VV-ST Standard W/G clamp kit 6 GHz • 2 for length > 900
mm and 1+1
configuration.
• 2 for 1+0
configuration.
ACC-FL-07-SV-EX Extended W/G clamp kit 7/8 GHz for W/G 1 for length <= 900 mm
900 mm and 1+1 configuration.
ACC-FL-07-LU-EX Extended W/G clamp kit 7/8 GHz, 1+0 1 for 1+0 configuration.
ACC-FL-07-VV-ST Standard W/G clamp kit 7/8 GHz • 2 for length > 900
mm and 1+1
configuration.
• 2 for 1+0
configuration.
ACC-FL-13-VV-ST Standard W/G clamp kit 11/13/15 GHz 2
ACC-FL-23-VV-ST Standard W/G clamp Kit 18-38 GHz 2
-54-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
Standard Kit
ACC-FL-06-VV-ST
ACC-FL-07-VV-ST
ACC-FL-13-VV-ST
ACC-FL-23-VV-ST
(1) Extended kits 1+0 slightly differs from extended kits in pole extension section length.
-55-
9. Waveguide Kits
-56-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
-57-
Appendix A: Package Dimensions & Weights
-58-
OmniBAS Outdoor Units (ODUs)
Product Catalog - Edition 2.0
-59-
Appendix A: Package Dimensions & Weights
-60-
Intracom Telecom Regional Contacts