Documente Academic
Documente Profesional
Documente Cultură
All about IT and PC...Mother needs a father !Let the father to take care of the mother !
I have just done this on my DIR-300 successfully...not easy though for a beginner to ▼ 2008 (3)
start. There is some other online guidelines to teach how to flash the firmware but is not ▼ October (3)
clear enough, so here comes another guideline from myself. This is just an enhancement Streamyx goes mobile = streamyx hot spot !
Guide to flash DDWRT firmware on DIR-300
of this to make everything more clear.
Beginner talking on PCs
► 2007 (1)
Things to be download before start:
Telnet Client(Putty) Download Link :Putty Usage :To communicate within PC My Blog List
and Router
TFTP Server(PumpKin) Download Link :PumpKin Usage: To load all the files
that need to be transfer from PC to Router
ap61.ram Download Link:DD-WRT (/v24/Atheros WiSoc/D-Link About Me
DIR300/ap61.ram)*ftp download
ap61.rom Download Link:DD-WRT (/v24/Atheros WiSoc/D-Link Ryan Tham
DIR300/ap61.rom)*ftp download
As a Computer Engineer, would like to share all his
linux.bin Download Link:DD-WRT (/v24/Atheros WiSoc/D-Link information and knowledge to the society.
DIR300/linux.bin)*ftp download View my complete profile
Start Flashing
Connect the network cable from pc ethernet port to the WAN port of
DIR-300.
Configure PC static IP to be 192.168.20.80/255.255.255.0.
Hold on to the reset behind the DIR-300.
Power on the DIR-300 while holding on to the reset button. Hold the reset
button for 30 seconds while it is booting.
Release the reset button
Telnet to 192.168.20.81 on port 9000
You should be greeted by the RedBoot prompt. RedBoot> (Need to wait some
times)
1 of 4 12/4/2019, 8:57 PM
FatherBoard: Guide to flash DDWRT firmware on DIR-300 http://ryantham1987.blogspot.com/2008/10/guide-to-flash-ddwrt-firmwa...
Note: You may need to connect the ethernet cable to the LAN port instead of WAN port.
DD-WRT> fconfig -i
Initialize non-volatile configuration - continue (y/n)? y
Run script at boot: false
Use BOOTP for network configuration: true
Default server IP address:
Console baud rate: 9600
GDB connection port: 9000
Force console for special debug messages: false
Network debug at boot time: false
Update RedBoot non-volatile configuration - continue (y/n)? y
… Erase from 0xbffe0000-0xbfff0000: .
… Program from 0×80ff0000-0×81000000 at 0xbffe0000: .
DD-WRT> fis init
About to initialize [format] FLASH image system - continue (y/n)? y
*** Initialize FLASH Image System
… Erase from 0xbffe0000-0xbfff0000: .
… Program from 0×807f0000-0×80800000 at 0xbffe0000: .
Your DIR-300 will reset at this point. Telnet to it (192.168.1.1, port 9000) after it has
finish resetting. (approximately 30+ seconds)
2 of 4 12/4/2019, 8:57 PM
FatherBoard: Guide to flash DDWRT firmware on DIR-300 http://ryantham1987.blogspot.com/2008/10/guide-to-flash-ddwrt-firmwa...
The default username and password are “root” and “admin” (without the quotes)
respectively. Enjoy your new DIR-300!
Hope it
Helps....Happy
Flashing
Nice GUI
Great features
better routing than original firmware
although able to increase the TX power on the firmware but no effect at
all after increasing, and it is still 17db on the status tab on the GUI.
Pratically try it out and confirm no effect on changing the TX power on
the firmware.
3 of 4 12/4/2019, 8:57 PM
FatherBoard: Guide to flash DDWRT firmware on DIR-300 http://ryantham1987.blogspot.com/2008/10/guide-to-flash-ddwrt-firmwa...
2 comments:
junc said...
i did everything up to the first reset then nothings happen. Only power
indicator from my router is up, i've waited for almost 3hours and still the
same
July 19, 2010 at 6:47 PM
Very good steps. The pumpkin software was really a eyeopener as other
tutorials assume that the user is aware of these software.
The steps are still valid and working after 4 years. Thanks
July 30, 2014 at 8:02 AM
Post a Comment
4 of 4 12/4/2019, 8:57 PM