Documente Academic
Documente Profesional
Documente Cultură
重庆惠科金渝光电科技有限公司
Ver. 1.0
Date: 29. Mar.2017
( ) Preliminary Specification
( v ) Approval Specification
Any modification is not allowed without HKC’s permission
Reviewed By PM Date
Name: Pinky
Signature:
Contents
Revision History............................................................................................................................. 3
1. GENERAL DESCRIPTION .......................................................................................................... 4
1.1 General Specifications ........................................................................................................ 4
2. ABSOLUTE MAXIMUM RATINGS .............................................................................................. 5
2.1 Absolute Maximum Ratings ................................................................................................ 5
2.2 Absolute Ratings of Environment ........................................................................................ 5
3. ELECTRICAL SPECIFICATIONS ............................................................................................... 7
3.1 Electrical Characteristics .................................................................................................... 7
3.1.1 Power consumption .................................................................................................. 7
3.1.2 LVDS characteristics................................................................................................. 8
3.1.3 LVDS characteristics................................................................................................. 9
3.1.4 Block diagram ........................................................................................................... 9
3.2 Interface Connections ....................................................................................................... 10
3.3 Timing Spec. ..................................................................................................................... 12
3.4 Power On/Off Sequence ................................................................................................... 15
3.5 Flicker Adjustment ............................................................................................................ 16
3.6 Driver IC ESD spec ........................................................................................................... 16
4. OPTICAL CHARACTERISTICS ................................................................................................ 17
4.1 Measurement Conditions .................................................................................................. 17
4.2 Optical Specifications ....................................................................................................... 18
5. MECHANICAL CHARACTERISTICS ........................................................................................ 21
5.1 Mechanical Specification .................................................................................................. 21
5.2 Packing ............................................................................................................................. 22
5.2.1 Packing specifications ............................................................................................ 22
6. DEFINITION OF LABELS ......................................................................................................... 24
6.1 Open Cell Label ................................................................................................................ 24
6.2 Carton Label ..................................................................................................................... 25
6.3 Pallet Label ....................................................................................................................... 26
7. PRECAUTION ........................................................................................................................... 27
7.1 Unpacking ......................................................................................................................... 27
Revision History
1. GENERAL DESCRIPTION
The specification is applied to 31.5” model (PT320AT01-1) TFT Liquid Crystal Display open cell and it supports
1366 x 768 HD mode with 16.7M colors. This product is with driver ICs and a 30-pins-1ch-LVDS circuit board and built
in without backlight unit.
Scan direction
Note:
(1) a. 90 % RH Max. (Ta ≤ 40 °C).
b. Web-bulb temperature should be 39℃ Max.(Ta>40℃)
c. No condensation
d. Operating condition with a assemble module
(2) The temperature of panel surface should be 0 ºC min. and 50 ºC max.
(3) Any point on the Driver surface must be less than 105 ºC under any condition ,If the surface temperature is
out of the spec, thermal solutions should be applied to avoid be damaged.
3. ELECTRICAL SPECIFICATIONS
3.1 Electrical Characteristics
3.1.1 Power consumption
Value
Parameter Symbol Unit Note
Min. Typ. Max.
VCC
VCC×0.9
VCC×0.1
GND
470μs
(4) Measurement Conditions: Vcc =12V, Ta = 25 ± 2 ºC, Fv = 60 Hz, whereas the test pattern is shown as below.
VTH
VCM |VID|
VTL
GND
JEIDA Format
SCAN DRIVER
DATA
TIMING
VCC
CONTROLLE TFT LCD PANEL
R (1366x768)
DC/DC
CONVERTER
VOLTAGE
Note:
(1) Following finger shows the LVDS pin1 diagram.
(2) For HKC used only, please leave it open.
(3) High: connect to +3.3V→JEIDA Format;Low: connect to GND or Open→VESA Format.
#30 #1
(4) The first pixel is odd. Base on gate driver on left side, source driver on upside.
TV
TVD TVB
DE
TH
DCLK
TCLK
THB THD
DE
(4) The LVDS timing diagram and setup/hold time is defined and showed as the following figure.
90% 90%
OFF ON OFF
Backlight
Values
Parameters Units
Min. Typ. Max.
T1 0.5 - 10 ms
T2 0 - 50 ms
T3 500 - - ms
T4 100 - - ms
T5 0 - 50 ms
T6 1000 - - ms
Attention:
(1)The supply voltage of the external system for the module input should be the same as the definition.
(2) To avoid some abnormal display noise, we suggest " VCC falling time" to follow "T6” definition.
(3) The product should be always operated within above ranges.
(4) In case of VCC is off level, please keep the level of input signals on the low or keep high impedance.
Fig. 3.5 Source COF IC ESD protection Fig. 3.6 Gate COF IC ESD protection
4. OPTICAL CHARACTERISTICS
4.1 Measurement Conditions
The table below is the test condition of optical measurement.
Item Symbol Value Unit
Light source HKC 31.5" WXGA module White LED Backlight Module/ Film structure
4. 2 Optical Specifications
The relative measurement methods of optical characteristics are shown in 4.2. The following items should be
measured under the test conditions described in 4.1 and stable environment shown in 4.1.
Item Symbol Condition Min. Typ. Max. Unit Note
Rx 0.654
Red
Ry 0.327
Gx 0.278
Green θx=0°,θy=0°
Color Chromaticity Gy Typ - 0.578 Typ +
Viewing Angle at -- (1)
(CIE1931) Bx 0.03 0.136 0.03
Blue Normal Direction
By 0.105
at center point of
Wx 0.307
White panel,
Wy Light source is C 0.347
θx+ - 89 -
Horizontal
θx - - 89 -
Viewing Angle CR≧10 Deg. (6)
θy+ - 89 -
Vertical
θy- - 89 -
Note:
(1) Each chromaticity coordinates (x, y) are measured in CIE1931 color space when full-screen displaying
(Red, Green, Blue, White) and light source is defined by C-light, Measurements shall be made at the
center of the panel, and setup of measurement is shown in Fig 4.1.
(2) The color gamut is defined as the fraction in percent of the area of the triangle bounded by R, G, B
coordinates and the area is defined by NTSC 1931 color standard in the CIE color space. Chromaticity
coordinates are measured by CS2000 and the standard setup of measurement is shown in Fig 4.1.
(3) Definition of Transmittance (T%):
The transmittance is measured with full white pattern (Lmax) at the center of the LCD panel.
𝑪𝑹𝒘
Contrast Ratio (CR): 𝑪𝑹 =
𝑪𝑹𝑫
CRW : Luminance of LCD module with full screen white pattern (255,255, 255) at center point.
CRD : Luminance of LCD module with full screen Dark pattern (0, 0, 0) at center point.
Where the measure point of to the Contrast Ratio is the center of the panel
(5) Definition of Response time (T g):
Average of gray to gray response time (Tg) means the average switching time of luminance ratios
among 0%,25%,50%,75%,and 100% to each other and is optimized on frame rate =60Hz.
To
Measured Response time
0% 25% 50% 75% 100%
Fig 4.4
5. MECHANICAL CHARACTERISTICS
5.1 Mechanical Specification
5.2 Packing
5.2.1 Packing specifications
Specification
Item
Quantity Dimension (mm) Weight (kg)
Net Weight:14.1
Packing Box 15pcs/box 930 (L) x 590 (W) x 108.5 (H)
Gross Weight:15.82
Pallet 1 1200(L) x 1000 (W) x 150 (H) Net Weight:12
Stack Layer 9
Pallet after Packing 270pcs/pallet 1200(L) x 1000 (W) x 1074.5 (H) Gross Weight:304.17
6. DEFINITION OF LABELS
6.1 Open Cell Label
Model Name
Manufactured Date
Serial
Serial
Number
Number
Panel ID
Manufactured Date: Y M DD
Date: 01~31
Manufactured Date
Panel Size
Cell Quantity
Manufactured Date
7. PRECAUTION
Please pay attention to the followings when a TFT-LCD cell is used, handled and mounted.
7.1 Unpacking
Should use immediately after unpacking TFT -LCD cell to prevent the terminal corrosion.
Protection film for a polarizer on a TFT open cell should be slowly peeled off so that the electrostatic charge can be
minimized.
Source PCB should be connected to the ground when peel off the protection film.
The protection film should not be contacted to the driver during peeling off.