Documente Academic
Documente Profesional
Documente Cultură
In this article, I’m going to show you how to install macOS Sierra on PC. Finally, Apple has
just released the final version of macOS Sierra 10.12 on 20th September. So due to this, it
took the time to manage this article. Installing a Mac operating system on PC is actually
hard and is not working on all devices. Every company has its own device settings. So the
settings are not the same. If you follow this article very carefully, again you might have to
face any problem during installation. Because all Laptops or desktops are not the same. In
our today’s topic, I’m going to install macOS Sierra Hackintosh on PC on Lenovo Laptop.
We recommend you to visit these articles also:
o How to Install Mac OS X El Capitan on PC?
o How to Install Mac OS X El Capitan on PC Using UniBeast?
o How to Install Mac OS X El Capitan on VirtualBox?
o How to Dual Boot Windows 10 and Mac OS X El Capitan on PC?
o How to Create Bootable USB Installer for macOS Sierra Using UniBeast?
o How to Create macOS Sierra Bootable USB Installer on Windows 10?
BIOS Setup
#2. Now from BIOS, Set The SATA Controller Mode to (AHCI).
SATA Controller Mode
#3. Then Go to Boot Label and Set the Boot Mode to (Legacy Support) and Set the Boot
Priority to (UEFI First).
Boot UEFI Mode
#4. Then Exit and Save Changes.
#1. To partition the Disk for Mac OS. Now click on Utilities > Disk Utility.
o Fix “Erase Process has Failed” While Erasing Partition for Mac OS on Disk
Utility
Erase Process Completed
#9. Wait a little while to Setting Up Your Mac. Then it will run to the desktop of macOS
Sierra.
o Install & Fix macOS Sierra Bootloader, Ethernet, Audio Problem & Post
Installation of Hackintosh
If you want to get notified about the post installation of macOS Sierra full step by step
guides and other upcoming articles to solve error while installing macOS Sierra on PC then
just enter your email address below and get notified. Thanks for being with us.
This was all about, how to Install macOS Sierra on PC. If you faced any problem, tell us
below by comment, feel free to tell us. We’re waiting for your suggestion
How to Create macOS Sierra
Bootable USB Installer on
Windows 10?
FAIZ ORZ576 COMMENTS 0
In this article, I am going to show you how to create macOS Sierra bootable USB Installer on
Windows 10. If you are in the process to install macOS Sierra 10.12 on your PC
or Hackintosh, the first step is to create a bootable USB installer for macOS Sierra to
install Mac OS from it on your PC, you can create bootable USB Installer with UniBeast, but
still, you need a Macintosh to download and create macOS Sierra bootable USB Installer. So
here we’re to show you how to create bootable USB Installer for macOS Sierra on windows
10, and you don’t need any MacBook or an Apple computer.
Create macOS Sierra Bootable USB Installer
on Windows 10
To create a Bootable USB Installer, you need to download macOS Sierra image file from the
link below and other data that mentioned in the download section with an 8 or higher USB
flash drive. The download process is a little bit complicated if you are not known to mega
because you have to download it from there, also the credit goes to a Brazilian
Hackintosh group.
Note: This method works on Windows 7/8/10, and it’s not the TransMac process.
Step #1. Firstly, download the following materials from the link below.
Step #10. As mentioned above, download “Pacote de Config”. After downloading Extract it
also by 7-Zip, Winrar or any other extractor.
Extract “Pacote de config”
Step #11. Open “Pacote de Config” folder then select your PC if it’s desktop or laptop then
from its folder, you will find some system graphics Config.plist file. Find & Copy the
Config.plist that matches your Intell, AMD or NVIDIA system graphics.
Find & Copy your System Config.plist
Note: Remember that if you didn’t find the exact config.plist file for your system, use one
that approaches to your system. Like if your system graphics is Intel 4210 then choose
above or below that because it mostly works, though many might fix your system and
compatible with Hackintosh. Also, you might find your prepared config.plist file just by a
quick googling.
Step #12. Now go to your USB flash drive EFI > Clover then paste and replace the
config.plist file that you copied from “Pacote de Config” folder with default plist file.
Replace Config.plist to Bootable USB Installer
Also Read: How to Create Bootable USB Installer for macOS Sierra via UniBeast?
It was all about, how to create macOS Sierra bootable USB Installer on Windows 10. If
you’ve any question or quiery, feel free to share it in the comment section down below.