Documente Academic
Documente Profesional
Documente Cultură
SAFETY WARNING
Alcatel-Lucent training materials can be for products or refer to products that have both lethal and dangerous voltages
present. Always observe all safety precautions and do not work on the equipment alone. The user is strongly advised not to
wear conductive jewelry while working on the products. Equipment referred to or used during this course may be electrostatic
sensitive. Please observe correct anti-static precautions.
DISCLAIMER
ALCATEL-LUCENT DISCLAIMS ALL WARRANTIES REGARDING THE TRAINING COURSES OR THE CONTENT, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THE ALCATEL-LUCENT WILL NOT BE RESPONSIBLE OR LIABLE FOR ANY INJURY, LOSS, CLAIM, DAMAGE, OR ANY SPECIAL,
EXEMPLARY, PUNITIVE, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND (INCLUDING WITHOUT LIMITATION LOSS
PROFITS OR LOSS SAVINGS), WHETHER BASED IN CONTRACT, TORT, STRICT LIABILITY OR OTHERWISE, THAT ARISES OUT OF OR IS
IN ANY WAY CONNECTED WITH (A) ANY USE OR MISUSE OF THE CONTENT OR THE TRAINING COURSES BY YOU, OR (B) ANY FAILURE
OR DELAY BY ALCATEL-LUCENT, ITS OFFICERS, DIRECTORS, AGENTS OR EMPLOYEES IN CONNECTION WITH THE CONTENT OR THE
TRAINING COURSES (INCLUDING, WITHOUT LIMITATION, THE USE OF OR INABILITY TO USE ANY COMPONENT OF THE CONTENT OR
TRAINING BY YOU). SOME JURISDICTIONS LIMIT OR PROHIBIT SUCH EXCLUSION OF WARRANTIES OR LIMITATION OF LIABILITIES
AND SO THE FOREGOING EXCLUSION OF WARRANTIES OR LIMITATION OF LIABILITY MAY NOT APPLY TO YOU.
GOVERNING LAW
These Terms of Use and Legal Notice are governed by the laws of France. The operation and use of the training course is
governed by the laws of the country that governs your employment contract, if applicable. If any provision of these Terms of
Use and Legal Notice, or the application thereto to a person or circumstance, is held invalid or unenforceable by law, statute or
a court of competent jurisdiction, for any reason, then such provision shall be modified and/or superseded by a provision that
reflects the intent of the original provision as closely as possible. All other provisions of these Terms of Use and Legal Notice
shall remain in full force and effect. You may not assign these Terms of Use or any permission granted hereunder without
Alcatel-Lucent’s prior written consent. Nothing herein shall be deemed an employment agreement or an offer of employment
or an alteration in any way of a user’s terms of employment with or within Alcatel-Lucent.
Copyright © 2013 Alcatel-Lucent. All Rights Reserved
1. Operation
1. Common Operation
2. DATA Operation
training.feedback@alcatel-lucent.com
Thank you!
Document History
1 How to login 7
Exercise 14
2 How to set SID 15
3 Communication parameters configuration 18
3.1 DCN physical interface 19
3.2 DCC configuration 22
Exercise 30
3.3 IP tunnel configuration 34
3.4 Network domain 36
Exercise 41
3.5 NTP configuration 42
4 Configurations 47
4.1 Physical media parameter: ALS 48
4.2 TP configuration in RS 51
4.3 TP configuration in MS 58
Exercise 60
4.4 TP configuration in VC4 61
4.5 Restart 64
Exercise 67
4.6 Alarm list 70
5 Board declaration 72
Exercise 82
6 Housekeeping Support 87
References 91
End of module 92
1646 SM/SMC NE B can be managed by ZIC PC via Remote mode after configuration as follows:
Connect NE A and NE B with optical fiber
LAPD configurations (only valid for OSI network):
Set the NSAP address (for OSI networking) of NE A and NE B
Set LAPD parameters:
Type of DCC channels:
· Section
· Line
Type of layer 2 LAPD role:
· User
· Network
Set IP (over OSI) tunnel to reach NSAP address of NE B with ALU encapsulation type.
Add static route:
Define static route from NE B to ZIC PC
Define static route from ZIC PC to NE B
Document History
1 Introduction 7
2 Link aggregation 22
3 Ethernet transparent transport 36
4 Ethernet switch 46
4.1 Ethernet private line 47
4.2 Ethernet virtual private line 71
4.3 Ethernet virtual private LAN 85
4.4 Broad access 118
5 OAM 137
5.1 Introduction 138
5.2 EFM (Ethernet in the First Mile) 152
5.3 Standard OAM management 158
References 179
End of module 180
After “Save & Exit” the “Admin Status” of the UNI port is automatically set to “up”
If you enable the LCAS Control, at the bottom of the window, appear the following parameters:
- VCG Access Identifier, specifies the selected VCG entity to which the command is directed.
- Working Transmitting Channel Numbers. Indicates the the total number of channels within the addressed
VCG that are transmitting payloads (traffic).
- Working Receiving Channel Numbers. Indicates the the total number of channels within the addressed VCG
that are receiving payloads (traffic).
- MST Reference Channel. The VC channel used for retrieving the MST (Member Status Information).
(VCGVC4-{1-7}-{1-9}-{2-9,12-19}-{1-64}-{1-64} (VC4 within a logical VCG on a Multiservice Packet Card)
Channel used for Differential Delay. VC channel that has the most differential delay. (VCGVC4-{1-7}-{1-9}-{2-
9,12-19}-{1-64}-{1-64} (VC4 within a logical VCG on a Multiservice Packet Card)
- Re-Sequence Acknowledge Bit Transmitted.
If you enable the LCAS Control, at the bottom of the window, appear the following parameters:
- VCG Access Identifier, specifies the selected VCG entity to which the command is directed.
- Working Transmitting Channel Numbers. Indicates the the total number of channels within the addressed
VCG that are transmitting payloads (traffic).
- Working Receiving Channel Numbers. Indicates the the total number of channels within the addressed VCG
that are receiving payloads (traffic).
- MST Reference Channel. The VC channel used for retrieving the MST (Member Status Information).
(VCGVC4-{1-7}-{1-9}-{2-9,12-19}-{1-64}-{1-64} (VC4 within a logical VCG on a Multiservice Packet Card)
Channel used for Differential Delay. VC channel that has the most differential delay. (VCGVC4-{1-7}-{1-9}-{2-
9,12-19}-{1-64}-{1-64} (VC4 within a logical VCG on a Multiservice Packet Card)
- Re-Sequence Acknowledge Bit Transmitted.
Color Profile: specifies the association between incoming EVPL priorities and forwarded frame coloring
VLAN pop: if enabled, it pops out the “Stacked VLAN” field of the incoming Ethernet frame
Format: to define the format for the name of this MD. Possible values:
none
charString
dnsLikeName
macAddressAndUint
All Bridges belonging to the same MD must have the same format.
MHF Creation: to define the MHF (MIP Half Function) of this MD. Possible values:
defMHFnone: no MIP can be created for this MD.
defMHFdefault: MIPs can be created for this MD on any bridge port.
defMHFexplicit: MIPs can be created for this MD on bridge ports only if a MEP is created at lower
MD Level.
MHF Creation: to define the MHF (MIP Half Function) of this MA. Possible values:
defMHFnone: no MIP can be created for this MA.
defMHFdefault: MIPs can be created for this MA on any bridge port.
defMHFexplicit: MIPs can be created for this MA on bridge ports only if a MEP is created at lower
MD Level.
Ltm Priority: to associate a VLAN priority (0 to 7) to the Link Trace Message; default is 7.