Documente Academic
Documente Profesional
Documente Cultură
Features
■ Wide gain bandwidth: 1.3 MHz
■ Input common-mode voltage range includes
ground N
■ Large voltage gain: 100 dB DIP14
(Plastic package)
■ Very low supply current per amplifier: 375 µA
■ Low input bias current: 20 nA
■ Low input offset voltage: 5 mV max.
■ Low input offset current: 2 nA
■ Wide power supply range:
D
– Single supply: +3 V to +30 V
SO-14
■ Dual supplies: ±1.5 V to ±15 V (Plastic micropackage)
Description
The LM124, LM224 and LM324 consist of four
independent, high gain, internally frequency-
compensated operational amplifiers. They
P
operate from a single power supply over a wide
TSSOP-14
range of voltages. Operation from split power
(Thin shrink small outline package)
supplies is also possible and the low power
supply current drain is independent of the
magnitude of the power supply voltage.
Q
QFN16 3x3
(Plastic micropackage)
Output 1 1 14 Output 4
VCC + 4 11 VCC -
Output 2 7 8 Output 3
OUT1
OUT4
IN1-
IN4-
16
15
14
13
IN1+ 1 12 IN4+
VCC+ 2 11 VCC-
NC 3 10 NC
IN2+
IN2 4 9 IN3+
IN3
5
8
IN2-
IN3-
OUT2
OUT3
3 Electrical characteristics
IB (nA) 24 90
21 80 IO +
70
18
mA ID
Supply current (mA)
3
Input voltage (V)
10
Negative
2
Positive
5 Tamb = 0°C to +125°C
1
Tamb = -55°C
0 5 10 15 0 10 20 30
1.35
100
1.30
1.25 80
1.2
+7.5 V
1.15 60 100 kΩ
100 Ω
1.1
40 eO
1.05 eI 100 Ω
1 100 kΩ +7.5 V
20
0.95
0.9 0
-55 -35 -15 5 25 45 65 85 105 125 100 1k 10k 100k 1M
Figure 9. Open loop frequency response Figure 10. Large signal frequency response
140 10 MΩ
20
100 kΩ
0.1 uF
1 kΩ
120 VCC+ +15 V
eO eO
eI eI
15
100
Voltage gain (dB)
40
5
20 VCC+ = +10 to +15 V &
-55°C Tamb +125°C
0 0
1.0 10 100 1.0k 10k 100k 1.0M 10M 1k 10k 100k 1M
Frequency (Hz) Frequency (Hz)
Figure 11. Voltage follower pulse response Figure 12. Output characteristics (current
sinking)
10
4
Input voltage (V) - output voltage (V)
VCC+ = +5 V
RL 2 kΩ VCC+ = +15 V
3 VCC+ = +30 V
VCC+ = +15 V
2
Output voltage (V)
1
1
0 VCC+/2 VCC+
3 0.1 IO
2 VO
1
Tamb = +25°C
0.01
0 10 20 30 40 0.001 0.01 0.1 1 10 100
Time (μS) Output sink current (mA)
Figure 13. Voltage follower pulse response Figure 14. Output characteristics (current
(small signal) sourcing)
500 8
Output voltage referenced to VCC+ (V)
VCC+
7
450 eO VCC+/2 VO
Output voltage (mV)
6
50 pF
eI
400 5
IO
Input
4
350 Independent of VCC+
Output 3 Tamb = +25°C
300 2
Tamb = +25°C
VCC+ = +30 V
250 1
0 1 2 3 4 5 6 7 8 0.001 0.01 0.1 1 10 100
Time (μS) Output source current (mA)
Figure 15. Input current Figure 16. Large signal voltage gain
100 Avd (dB)
120
50 110
Tamb = +25°C
25 105
0 100
10 20 30 -55 -35 -15 5 25 45 65 80 105 125
Power supply voltage (V) Ambient temperature (°C)
Figure 17. Power supply and common mode Figure 18. Voltage gain
rejection ratio
(dB) 120 160
115
Power supply & common mode
SVR RL = 20 kΩ
110
120
105
rejection ratio (dB)
RL = 2 kΩ
Voltage gain (dB)
100
95 80
90
85
80 40
CMR
75
70
-55 -35 -15 5 25 45 65 85 105 125 0 10 20 30
Ambient temperature (°C) Power supply voltage (V)
Figure 19. AC coupled inverting amplifier Figure 20. High input Z adjustable gain DC
instrumentation amplifier
2 Vpp
if R1 = R5
and R3 = R4 = R6 = R7
2R
e0 = 1 + ----------1- (e2 -e1)
R
2
Figure 21. AC coupled non inverting amplifier Figure 22. DC summing amplifier
2 Vpp
Figure 23. Non-inverting DC gain Figure 24. Low drift peak detector
Figure 25. Active bandpass filter Figure 26. High input Z, DC differential
amplifier
R R
1 4
For ------- = -------
R R
2 3
(CMRR depends on this resistor ratio match)
Fo = 1kHz e0
⎛ 1 + R-------4⎞ (e2 - e1)
Q = 50 ⎝ R3⎠
Av = 100 (40dB)
As shown e0 = (e2 - e1)
5 Package information
Millimeters Inches
Ref.
Min. Typ. Max. Min. Typ. Max.
A 5.33 0.21
A1 0.38 0.015
A2 2.92 3.30 4.95 0.11 0.13 0.19
b 0.36 0.46 0.56 0.014 0.018 0.022
b2 1.14 1.52 1.78 0.04 0.06 0.07
c 0.20 0.25 0.36 0.007 0.009 0.01
D 18.67 19.05 19.69 0.73 0.75 0.77
E 7.62 7.87 8.26 0.30 0.31 0.32
E1 6.10 6.35 7.11 0.24 0.25 0.28
e 2.54 0.10
e1 15.24 0.60
eA 7.62 0.30
eB 10.92 0.43
L 2.92 3.30 3.81 0.11 0.13 0.15
Millimeters Inches
Ref.
Min. Typ. Max. Min. Typ. Max.
A 1.20 0.047
A1 0.05 0.15 0.002 0.004 0.006
A2 0.80 1.00 1.05 0.031 0.039 0.041
b 0.19 0.30 0.007 0.012
c 0.09 0.20 0.004 0.0089
D 4.90 5.00 5.10 0.193 0.197 0.201
E 6.20 6.40 6.60 0.244 0.252 0.260
E1 4.30 4.40 4.50 0.169 0.173 0.176
e 0.65 0.0256
L 0.45 0.60 0.75 0.018 0.024 0.030
L1 1.00 0.039
k 0° 8° 0° 8°
aaa 0.10 0.004
6 Ordering information
7 Revision history
0
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.