Documente Academic
Documente Profesional
Documente Cultură
in ADC Circuits
By Bonnie C. Baker, Microchip Technology Inc.
If all three of these issues are addressed, then it is true that No low-pass anti-aliasing filter included
designing a low noise 12-bit ADC board is easy. No by-pass capacitors included
An example of a 12-bit circuit is shown in Figure 1. The signal
No ground plane used
originates at the resistive load cell, part number LCL-816-G. The
differential output ports of the LCL-816-G are connected to a
discrete, two-op-amp instrumentation amplifier (A1, A2, R3, R4
and RG). The signal then travels through a second order, low-
pass filter (A3, R5, R6, C1 and C2). This low-pass filter eliminates
unwanted, higher frequency noise. Finally, the signal couples into
a 12-bit ADC (A4, MCP3201). The converter is configured to
accept signals from 0V to 5V. The output of the converter is sent
to the PIC16C623 microcontroller.
VDD
_ C1
R1 R2 R4
1/4 of
_
MCP6024
R6
PIC16C623
1/4 of R5 A4
+ A1 + SCLK
MCP6024
R2 R1 1/41/4
of of DOUT
C2 MCP3201
+ A2 MCP6024
MCP6024
LCL-816G CS
_
A3
Figure 1. When you use low noise devices, a ground plane, by-pass capacitors and a low-pass filter, it is possible to produce an accurate,
12-bit conversion every time.
70
capacitors not only remove noise but also foster circuit stability.
60
50
Code Width of Noise = 1
40 (Total Samples = 1024)
30 1100
20 1000
Number of Occurrences
10 900
0 800
700
2960 2970 2980 2990 600
Output Code of 12-bit A/D Converter 500
400
Figure 2. When low noise precautions are not taken during circuit 300
design and board layout, a 12-bit ADC system under-performs with 200
approximately 5.45-bit accuracy (or 5.45 Effective Number of Bits). 100
0
Modifying this circuit and board can result in a 12-bit 2940 2941 2942
accurate solution. As a first step, lower noise devices
Output Code of 12-bit A/D Converter
are used. For instance, the resistors are made 10 times
lower. When this is done, the gain remains the same,
but the noise is reduced by approximately 3 times. Figure 3. If low noise, active and passive devices are used, a ground
Additionally, the amplifiers are changed from the MCP604 plane is included, by-pass capacitors are added and a low-pass
to the MCP6044. The MCP604’s voltage noise density, (anti-aliasing) filter is placed in the signal path. The code width of 1024
samples is equal to one.
at 1 kHz, is 29 nV/ √Hz (typ). The MCP6024’s voltage
noise density, at 10 kHz, is 8.7 nV/ √Hz (typ). This is over
3 times improvement. As a third modification, a ground plane Recommended References:
is added to the Printed Circuit Board (PCB). This ground plane
is implemented so that interruptions in the metal are parallel AN681 - Reading and Using Fast Fourier Transforms (FFTs),
instead of horizontal to the signal path. Baker, Bonnie C., Microchip Technology Inc.
The performance of the board changes dramatically with these
three modifications. Tests show that the histogram output AN688 - Layout Tips for 12-Bit A/D Converter Application,
of the ADC changes from a code width of 44 codes down to Baker, Bonnie C., Microchip Technology Inc.
9 codes. This dramatic change converts the circuit in Figure 1
into approximately a 9-bit system. AN695 - Interfacing Pressure Sensors to Microchip’s
Analog Peripherals, Baker, Bonnie C.,
This sounds good, but there is a 12-bit system to be found Microchip Technology Inc.
in this application. Adding a second order filter (A3, R5, R6,
C1 and C2), which is designed using the FilterLab® software, AN699 - Anti-Aliasing, Analog Filters for Data Acquisition
improves the performance. Additionally, including the by-pass Systems, Baker, Bonnie C., Microchip Technology Inc.
capacitors turns this system into a true 12-bit accurate system.
This is illustrated in Figure 3 where 1024 samples are collected Noise Reduction Techniques in Electronic Systems, Henry Ott,
from the converter at a data rate of 30 ksps and all 1024 John Wiley, N.Y., 1998.
samples are equivalent to one code: 2941.